From af6521ea8af210fea094b183a9ad29ab73945ee1 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Fri, 5 Oct 2007 21:46:53 +0400 Subject: [PATCH] [POWERPC] 85xx: mpc8568mds - update dts to be able to use UCCs 1. UCC1's RX_DV pin is 16, not 15; 2. UCC1's phy is at 0x7, not 0x1. Schematics says 0x7, and recent u-boot also using 0x7. 3. Use gianfar's (eTSEC) mdio bus. This is hardware default setup. 4. tx-clock should be CLK16 (GE125, PB31); 5. phy-connection-type is RGMII-ID; Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8568mds.dts | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts index b064a2ff230..54394372b12 100644 --- a/arch/powerpc/boot/dts/mpc8568mds.dts +++ b/arch/powerpc/boot/dts/mpc8568mds.dts @@ -104,10 +104,10 @@ device_type = "mdio"; compatible = "gianfar"; reg = <24520 20>; - phy0: ethernet-phy@0 { + phy0: ethernet-phy@7 { interrupt-parent = <&mpic>; interrupts = <1 1>; - reg = <0>; + reg = <7>; device_type = "ethernet-phy"; }; phy1: ethernet-phy@1 { @@ -242,7 +242,7 @@ 4 1a 2 0 2 0 /* RxD7 */ 4 0b 1 0 2 0 /* TX_EN */ 4 18 1 0 2 0 /* TX_ER */ - 4 0f 2 0 2 0 /* RX_DV */ + 4 10 2 0 2 0 /* RX_DV */ 4 1e 2 0 2 0 /* RX_ER */ 4 11 2 0 2 0 /* RX_CLK */ 4 13 1 0 2 0 /* GTX_CLK */ @@ -334,10 +334,10 @@ mac-address = [ 00 00 00 00 00 00 ]; local-mac-address = [ 00 00 00 00 00 00 ]; rx-clock = <0>; - tx-clock = <19>; - phy-handle = <&qe_phy0>; - phy-connection-type = "gmii"; + tx-clock = <20>; pio-handle = <&pio1>; + phy-handle = <&phy0>; + phy-connection-type = "rgmii-id"; }; ucc@3000 { @@ -356,10 +356,10 @@ mac-address = [ 00 00 00 00 00 00 ]; local-mac-address = [ 00 00 00 00 00 00 ]; rx-clock = <0>; - tx-clock = <14>; - phy-handle = <&qe_phy1>; - phy-connection-type = "gmii"; + tx-clock = <20>; pio-handle = <&pio2>; + phy-handle = <&phy1>; + phy-connection-type = "rgmii-id"; }; mdio@2120 { @@ -371,10 +371,10 @@ /* These are the same PHYs as on * gianfar's MDIO bus */ - qe_phy0: ethernet-phy@00 { + qe_phy0: ethernet-phy@07 { interrupt-parent = <&mpic>; interrupts = <1 1>; - reg = <0>; + reg = <7>; device_type = "ethernet-phy"; }; qe_phy1: ethernet-phy@01 { -- 2.41.1