From 81d4903d2d17a9f33ece2666185a8b51e6935ae0 Mon Sep 17 00:00:00 2001 From: Greg Ungerer Date: Mon, 12 Sep 2005 11:18:10 +1000 Subject: [PATCH] [PATCH] m68knommu: common RAM based 68360 startup code Create common start code for all 68360 based platforms that are loaded and run directly from RAM (as opposed to running from flash/ROM). This replaces the old specific startup code for each board. Signed-off-by: Greg Ungerer Signed-off-by: Linus Torvalds --- arch/m68knommu/platform/68360/head-ram.S | 408 +++++++++++++++++++++++ 1 file changed, 408 insertions(+) create mode 100644 arch/m68knommu/platform/68360/head-ram.S diff --git a/arch/m68knommu/platform/68360/head-ram.S b/arch/m68knommu/platform/68360/head-ram.S new file mode 100644 index 00000000000..a5c639a51ee --- /dev/null +++ b/arch/m68knommu/platform/68360/head-ram.S @@ -0,0 +1,408 @@ +/* arch/m68knommu/platform/68360/head-ram.S + * + * Startup code for Motorola 68360 + * + * Copyright 2001 (C) SED Systems, a Division of Calian Ltd. + * Based on: arch/m68knommu/platform/68328/pilot/crt0_rom.S + * Based on: arch/m68knommu/platform/68360/uCquicc/crt0_rom.S, 2.0.38.1.pre7 + * uClinux Kernel + * Copyright (C) Michael Leslie + * Based on: arch/m68knommu/platform/68EZ328/ucsimm/crt0_rom.S + * Copyright (C) 1998 D. Jeff Dionne , + * + */ +#define ASSEMBLY +#include + +.global _stext +.global _start + +.global _rambase +.global __ramvec +.global _ramvec +.global _ramstart +.global _ramend + +.global _quicc_base +.global _periph_base + +#define REGB 0x1000 +#define PEPAR (_dprbase + REGB + 0x0016) +#define GMR (_dprbase + REGB + 0x0040) +#define OR0 (_dprbase + REGB + 0x0054) +#define BR0 (_dprbase + REGB + 0x0050) +#define OR1 (_dprbase + REGB + 0x0064) +#define BR1 (_dprbase + REGB + 0x0060) +#define OR4 (_dprbase + REGB + 0x0094) +#define BR4 (_dprbase + REGB + 0x0090) +#define OR6 (_dprbase + REGB + 0x00b4) +#define BR6 (_dprbase + REGB + 0x00b0) +#define OR7 (_dprbase + REGB + 0x00c4) +#define BR7 (_dprbase + REGB + 0x00c0) + +#define MCR (_dprbase + REGB + 0x0000) +#define AVR (_dprbase + REGB + 0x0008) + +#define SYPCR (_dprbase + REGB + 0x0022) + +#define PLLCR (_dprbase + REGB + 0x0010) +#define CLKOCR (_dprbase + REGB + 0x000C) +#define CDVCR (_dprbase + REGB + 0x0014) + +#define BKAR (_dprbase + REGB + 0x0030) +#define BKCR (_dprbase + REGB + 0x0034) +#define SWIV (_dprbase + REGB + 0x0023) +#define PICR (_dprbase + REGB + 0x0026) +#define PITR (_dprbase + REGB + 0x002A) + +/* Define for all memory configuration */ +#define MCU_SIM_GMR 0x00000000 +#define SIM_OR_MASK 0x0fffffff + +/* Defines for chip select zero - the flash */ +#define SIM_OR0_MASK 0x20000002 +#define SIM_BR0_MASK 0x00000001 + + +/* Defines for chip select one - the RAM */ +#define SIM_OR1_MASK 0x10000000 +#define SIM_BR1_MASK 0x00000001 + +#define MCU_SIM_MBAR_ADRS 0x0003ff00 +#define MCU_SIM_MBAR_BA_MASK 0xfffff000 +#define MCU_SIM_MBAR_AS_MASK 0x00000001 + +#define MCU_SIM_PEPAR 0x00B4 + +#define MCU_DISABLE_INTRPTS 0x2700 +#define MCU_SIM_AVR 0x00 + +#define MCU_SIM_MCR 0x00005cff + +#define MCU_SIM_CLKOCR 0x00 +#define MCU_SIM_PLLCR 0x8000 +#define MCU_SIM_CDVCR 0x0000 + +#define MCU_SIM_SYPCR 0x0000 +#define MCU_SIM_SWIV 0x00 +#define MCU_SIM_PICR 0x0000 +#define MCU_SIM_PITR 0x0000 + + +#include + + +/* + * By the time this RAM specific code begins to execute, DPRAM + * and DRAM should already be mapped and accessible. + */ + + .text +_start: +_stext: + nop + ori.w #MCU_DISABLE_INTRPTS, %sr /* disable interrupts: */ + /* We should not need to setup the boot stack the reset should do it. */ + movea.l #__ramend, %sp /*set up stack at the end of DRAM:*/ + +set_mbar_register: + moveq.l #0x07, %d1 /* Setup MBAR */ + movec %d1, %dfc + + lea.l MCU_SIM_MBAR_ADRS, %a0 + move.l #_dprbase, %d0 + andi.l #MCU_SIM_MBAR_BA_MASK, %d0 + ori.l #MCU_SIM_MBAR_AS_MASK, %d0 + moves.l %d0, %a0@ + + moveq.l #0x05, %d1 + movec.l %d1, %dfc + + /* Now we can begin to access registers in DPRAM */ + +set_sim_mcr: + /* Set Module Configuration Register */ + move.l #MCU_SIM_MCR, MCR + + /* to do: Determine cause of reset */ + + /* + * configure system clock MC68360 p. 6-40 + * (value +1)*osc/128 = system clock + */ +set_sim_clock: + move.w #MCU_SIM_PLLCR, PLLCR + move.b #MCU_SIM_CLKOCR, CLKOCR + move.w #MCU_SIM_CDVCR, CDVCR + + /* Wait for the PLL to settle */ + move.w #16384, %d0 +pll_settle_wait: + subi.w #1, %d0 + bne pll_settle_wait + + /* Setup the system protection register, and watchdog timer register */ + move.b #MCU_SIM_SWIV, SWIV + move.w #MCU_SIM_PICR, PICR + move.w #MCU_SIM_PITR, PITR + move.w #MCU_SIM_SYPCR, SYPCR + + /* Clear DPRAM - system + parameter */ + movea.l #_dprbase, %a0 + movea.l #_dprbase+0x2000, %a1 + + /* Copy 0 to %a0 until %a0 == %a1 */ +clear_dpram: + movel #0, %a0@+ + cmpal %a0, %a1 + bhi clear_dpram + +configure_memory_controller: + /* Set up Global Memory Register (GMR) */ + move.l #MCU_SIM_GMR, %d0 + move.l %d0, GMR + +configure_chip_select_0: + move.l #__ramend, %d0 + subi.l #__ramstart, %d0 + subq.l #0x01, %d0 + eori.l #SIM_OR_MASK, %d0 + ori.l #SIM_OR0_MASK, %d0 + move.l %d0, OR0 + + move.l #__ramstart, %d0 + ori.l #SIM_BR0_MASK, %d0 + move.l %d0, BR0 + +configure_chip_select_1: + move.l #__rom_end, %d0 + subi.l #__rom_start, %d0 + subq.l #0x01, %d0 + eori.l #SIM_OR_MASK, %d0 + ori.l #SIM_OR1_MASK, %d0 + move.l %d0, OR1 + + move.l #__rom_start, %d0 + ori.l #SIM_BR1_MASK, %d0 + move.l %d0, BR1 + + move.w #MCU_SIM_PEPAR, PEPAR + + /* point to vector table: */ + move.l #_romvec, %a0 + move.l #_ramvec, %a1 +copy_vectors: + move.l %a0@, %d0 + move.l %d0, %a1@ + move.l %a0@, %a1@ + addq.l #0x04, %a0 + addq.l #0x04, %a1 + cmp.l #_start, %a0 + blt copy_vectors + + move.l #_ramvec, %a1 + movec %a1, %vbr + + + /* Copy data segment from ROM to RAM */ + moveal #_stext, %a0 + moveal #_sdata, %a1 + moveal #_edata, %a2 + + /* Copy %a0 to %a1 until %a1 == %a2 */ +LD1: + move.l %a0@, %d0 + addq.l #0x04, %a0 + move.l %d0, %a1@ + addq.l #0x04, %a1 + cmp.l #_edata, %a1 + blt LD1 + + moveal #_sbss, %a0 + moveal #_ebss, %a1 + + /* Copy 0 to %a0 until %a0 == %a1 */ +L1: + movel #0, %a0@+ + cmpal %a0, %a1 + bhi L1 + +load_quicc: + move.l #_dprbase, _quicc_base + +store_ram_size: + /* Set ram size information */ + move.l #_sdata, _rambase + move.l #_ebss, _ramstart + move.l #__ramend, %d0 + sub.l #0x1000, %d0 /* Reserve 4K for stack space.*/ + move.l %d0, _ramend /* Different from __ramend.*/ + +store_flash_size: + /* Set rom size information */ + move.l #__rom_end, %d0 + sub.l #__rom_start, %d0 + move.l %d0, rom_length + + pea 0 + pea env + pea %sp@(4) + pea 0 + + lea init_thread_union, %a2 + lea 0x2000(%a2), %sp + +lp: + jsr start_kernel + +_exit: + jmp _exit + + + .data + .align 4 +env: + .long 0 +_quicc_base: + .long 0 +_periph_base: + .long 0 +_ramvec: + .long 0 +_rambase: + .long 0 +_ramstart: + .long 0 +_ramend: + .long 0 +_dprbase: + .long 0xffffe000 + + .text + + /* + * These are the exception vectors at boot up, they are copied into RAM + * and then overwritten as needed. + */ + +.section ".data.initvect","awx" + .long __ramend /* Reset: Initial Stack Pointer - 0. */ + .long _start /* Reset: Initial Program Counter - 1. */ + .long buserr /* Bus Error - 2. */ + .long trap /* Address Error - 3. */ + .long trap /* Illegal Instruction - 4. */ + .long trap /* Divide by zero - 5. */ + .long trap /* CHK, CHK2 Instructions - 6. */ + .long trap /* TRAPcc, TRAPV Instructions - 7. */ + .long trap /* Privilege Violation - 8. */ + .long trap /* Trace - 9. */ + .long trap /* Line 1010 Emulator - 10. */ + .long trap /* Line 1111 Emualtor - 11. */ + .long trap /* Harware Breakpoint - 12. */ + .long trap /* (Reserved for Coprocessor Protocol Violation)- 13. */ + .long trap /* Format Error - 14. */ + .long trap /* Uninitialized Interrupt - 15. */ + .long trap /* (Unassigned, Reserver) - 16. */ + .long trap /* (Unassigned, Reserver) - 17. */ + .long trap /* (Unassigned, Reserver) - 18. */ + .long trap /* (Unassigned, Reserver) - 19. */ + .long trap /* (Unassigned, Reserver) - 20. */ + .long trap /* (Unassigned, Reserver) - 21. */ + .long trap /* (Unassigned, Reserver) - 22. */ + .long trap /* (Unassigned, Reserver) - 23. */ + .long trap /* Spurious Interrupt - 24. */ + .long trap /* Level 1 Interrupt Autovector - 25. */ + .long trap /* Level 2 Interrupt Autovector - 26. */ + .long trap /* Level 3 Interrupt Autovector - 27. */ + .long trap /* Level 4 Interrupt Autovector - 28. */ + .long trap /* Level 5 Interrupt Autovector - 29. */ + .long trap /* Level 6 Interrupt Autovector - 30. */ + .long trap /* Level 7 Interrupt Autovector - 31. */ + .long system_call /* Trap Instruction Vectors 0 - 32. */ + .long trap /* Trap Instruction Vectors 1 - 33. */ + .long trap /* Trap Instruction Vectors 2 - 34. */ + .long trap /* Trap Instruction Vectors 3 - 35. */ + .long trap /* Trap Instruction Vectors 4 - 36. */ + .long trap /* Trap Instruction Vectors 5 - 37. */ + .long trap /* Trap Instruction Vectors 6 - 38. */ + .long trap /* Trap Instruction Vectors 7 - 39. */ + .long trap /* Trap Instruction Vectors 8 - 40. */ + .long trap /* Trap Instruction Vectors 9 - 41. */ + .long trap /* Trap Instruction Vectors 10 - 42. */ + .long trap /* Trap Instruction Vectors 11 - 43. */ + .long trap /* Trap Instruction Vectors 12 - 44. */ + .long trap /* Trap Instruction Vectors 13 - 45. */ + .long trap /* Trap Instruction Vectors 14 - 46. */ + .long trap /* Trap Instruction Vectors 15 - 47. */ + .long 0 /* (Reserved for Coprocessor) - 48. */ + .long 0 /* (Reserved for Coprocessor) - 49. */ + .long 0 /* (Reserved for Coprocessor) - 50. */ + .long 0 /* (Reserved for Coprocessor) - 51. */ + .long 0 /* (Reserved for Coprocessor) - 52. */ + .long 0 /* (Reserved for Coprocessor) - 53. */ + .long 0 /* (Reserved for Coprocessor) - 54. */ + .long 0 /* (Reserved for Coprocessor) - 55. */ + .long 0 /* (Reserved for Coprocessor) - 56. */ + .long 0 /* (Reserved for Coprocessor) - 57. */ + .long 0 /* (Reserved for Coprocessor) - 58. */ + .long 0 /* (Unassigned, Reserved) - 59. */ + .long 0 /* (Unassigned, Reserved) - 60. */ + .long 0 /* (Unassigned, Reserved) - 61. */ + .long 0 /* (Unassigned, Reserved) - 62. */ + .long 0 /* (Unassigned, Reserved) - 63. */ + /* The assignment of these vectors to the CPM is */ + /* dependent on the configuration of the CPM vba */ + /* fields. */ + .long 0 /* (User-Defined Vectors 1) CPM Error - 64. */ + .long 0 /* (User-Defined Vectors 2) CPM Parallel IO PC11- 65. */ + .long 0 /* (User-Defined Vectors 3) CPM Parallel IO PC10- 66. */ + .long 0 /* (User-Defined Vectors 4) CPM SMC2 / PIP - 67. */ + .long 0 /* (User-Defined Vectors 5) CPM SMC1 - 68. */ + .long 0 /* (User-Defined Vectors 6) CPM SPI - 69. */ + .long 0 /* (User-Defined Vectors 7) CPM Parallel IO PC9 - 70. */ + .long 0 /* (User-Defined Vectors 8) CPM Timer 4 - 71. */ + .long 0 /* (User-Defined Vectors 9) CPM Reserved - 72. */ + .long 0 /* (User-Defined Vectors 10) CPM Parallel IO PC8- 73. */ + .long 0 /* (User-Defined Vectors 11) CPM Parallel IO PC7- 74. */ + .long 0 /* (User-Defined Vectors 12) CPM Parallel IO PC6- 75. */ + .long 0 /* (User-Defined Vectors 13) CPM Timer 3 - 76. */ + .long 0 /* (User-Defined Vectors 14) CPM Reserved - 77. */ + .long 0 /* (User-Defined Vectors 15) CPM Parallel IO PC5- 78. */ + .long 0 /* (User-Defined Vectors 16) CPM Parallel IO PC4- 79. */ + .long 0 /* (User-Defined Vectors 17) CPM Reserved - 80. */ + .long 0 /* (User-Defined Vectors 18) CPM RISC Timer Tbl - 81. */ + .long 0 /* (User-Defined Vectors 19) CPM Timer 2 - 82. */ + .long 0 /* (User-Defined Vectors 21) CPM Reserved - 83. */ + .long 0 /* (User-Defined Vectors 22) CPM IDMA2 - 84. */ + .long 0 /* (User-Defined Vectors 23) CPM IDMA1 - 85. */ + .long 0 /* (User-Defined Vectors 24) CPM SDMA Bus Err - 86. */ + .long 0 /* (User-Defined Vectors 25) CPM Parallel IO PC3- 87. */ + .long 0 /* (User-Defined Vectors 26) CPM Parallel IO PC2- 88. */ + .long 0 /* (User-Defined Vectors 27) CPM Timer 1 - 89. */ + .long 0 /* (User-Defined Vectors 28) CPM Parallel IO PC1- 90. */ + .long 0 /* (User-Defined Vectors 29) CPM SCC 4 - 91. */ + .long 0 /* (User-Defined Vectors 30) CPM SCC 3 - 92. */ + .long 0 /* (User-Defined Vectors 31) CPM SCC 2 - 93. */ + .long 0 /* (User-Defined Vectors 32) CPM SCC 1 - 94. */ + .long 0 /* (User-Defined Vectors 33) CPM Parallel IO PC0- 95. */ + /* I don't think anything uses the vectors after here. */ + .long 0 /* (User-Defined Vectors 34) - 96. */ + .long 0,0,0,0,0 /* (User-Defined Vectors 35 - 39). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 40 - 49). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 50 - 59). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 60 - 69). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 70 - 79). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 80 - 89). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 90 - 99). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 100 - 109). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 110 - 119). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 120 - 129). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 130 - 139). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 140 - 149). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 150 - 159). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 160 - 169). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 170 - 179). */ + .long 0,0,0,0,0,0,0,0,0,0 /* (User-Defined Vectors 180 - 189). */ + .long 0,0,0 /* (User-Defined Vectors 190 - 192). */ +.text +ignore: rte -- 2.41.1