From 7d2f6075f992d33c7be829c3638b8cb72b782b19 Mon Sep 17 00:00:00 2001 From: Nathan Lynch Date: Sun, 27 Jul 2008 15:24:50 +1000 Subject: [PATCH] powerpc: kill useless SMT code in prom_hold_cpus This piece of code is broken for >2 threads, and possibly in some other subtle ways (such as comparing a value obtained from an "ibm,ppc-interrupt-server#s" property to a value obtained from a "reg" property) and doesn't seem to have any useful purpose in the first place other than a dubious warning in case NR_CPUS is too small, which probably isn't the right place to do so. Signed-off-by: Nathan Lynch Signed-off-by: Benjamin Herrenschmidt --- arch/powerpc/kernel/prom_init.c | 39 +++------------------------------ 1 file changed, 3 insertions(+), 36 deletions(-) diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c index c4ab2195b9c..b72849ac7db 100644 --- a/arch/powerpc/kernel/prom_init.c +++ b/arch/powerpc/kernel/prom_init.c @@ -205,8 +205,6 @@ static int __initdata mem_reserve_cnt; static cell_t __initdata regbuf[1024]; -#define MAX_CPU_THREADS 2 - /* * Error results ... some OF calls will return "-1" on error, some * will return 0, some will return either. To simplify, here are @@ -1339,10 +1337,6 @@ static void __init prom_hold_cpus(void) unsigned int reg; phandle node; char type[64]; - int cpuid = 0; - unsigned int interrupt_server[MAX_CPU_THREADS]; - unsigned int cpu_threads, hw_cpu_num; - int propsize; struct prom_t *_prom = &RELOC(prom); unsigned long *spinloop = (void *) LOW_ADDR(__secondary_hold_spinloop); @@ -1386,7 +1380,6 @@ static void __init prom_hold_cpus(void) reg = -1; prom_getprop(node, "reg", ®, sizeof(reg)); - prom_debug("\ncpuid = 0x%x\n", cpuid); prom_debug("cpu hw idx = 0x%x\n", reg); /* Init the acknowledge var which will be reset by @@ -1395,28 +1388,9 @@ static void __init prom_hold_cpus(void) */ *acknowledge = (unsigned long)-1; - propsize = prom_getprop(node, "ibm,ppc-interrupt-server#s", - &interrupt_server, - sizeof(interrupt_server)); - if (propsize < 0) { - /* no property. old hardware has no SMT */ - cpu_threads = 1; - interrupt_server[0] = reg; /* fake it with phys id */ - } else { - /* We have a threaded processor */ - cpu_threads = propsize / sizeof(u32); - if (cpu_threads > MAX_CPU_THREADS) { - prom_printf("SMT: too many threads!\n" - "SMT: found %x, max is %x\n", - cpu_threads, MAX_CPU_THREADS); - cpu_threads = 1; /* ToDo: panic? */ - } - } - - hw_cpu_num = interrupt_server[0]; - if (hw_cpu_num != _prom->cpu) { + if (reg != _prom->cpu) { /* Primary Thread of non-boot cpu */ - prom_printf("%x : starting cpu hw idx %x... ", cpuid, reg); + prom_printf("starting cpu hw idx %x... ", reg); call_prom("start-cpu", 3, 0, node, secondary_hold, reg); @@ -1431,17 +1405,10 @@ static void __init prom_hold_cpus(void) } #ifdef CONFIG_SMP else - prom_printf("%x : boot cpu %x\n", cpuid, reg); + prom_printf("boot cpu hw idx %x\n", reg); #endif /* CONFIG_SMP */ - - /* Reserve cpu #s for secondary threads. They start later. */ - cpuid += cpu_threads; } - if (cpuid > NR_CPUS) - prom_printf("WARNING: maximum CPUs (" __stringify(NR_CPUS) - ") exceeded: ignoring extras\n"); - prom_debug("prom_hold_cpus: end...\n"); } -- 2.41.1