From 590031450a52c373bf72f5fb156fbcc0c78c6f2c Mon Sep 17 00:00:00 2001 From: Michael Hennerich Date: Sun, 21 Oct 2007 16:54:27 +0800 Subject: [PATCH] Blackfin arch: add new processor ADSP-BF52x arch/mach support Signed-off-by: Michael Hennerich Signed-off-by: Bryan Wu --- arch/blackfin/Kconfig | 51 +- arch/blackfin/Makefile | 6 + arch/blackfin/configs/BF527-EZKIT_defconfig | 1241 +++++++++++++++++ arch/blackfin/kernel/bfin_gpio.c | 35 +- arch/blackfin/kernel/reboot.c | 2 +- arch/blackfin/mach-bf527/Kconfig | 251 ++++ arch/blackfin/mach-bf527/Makefile | 9 + arch/blackfin/mach-bf527/boards/Makefile | 7 + arch/blackfin/mach-bf527/boards/eth_mac.c | 50 + arch/blackfin/mach-bf527/boards/ezkit.c | 737 ++++++++++ arch/blackfin/mach-bf527/cpu.c | 161 +++ arch/blackfin/mach-bf527/dma.c | 115 ++ arch/blackfin/mach-bf527/head.S | 456 ++++++ arch/blackfin/mach-bf527/ints-priority.c | 100 ++ arch/blackfin/mach-common/ints-priority-sc.c | 41 +- include/asm-blackfin/bf5xx_timers.h | 2 +- include/asm-blackfin/gpio.h | 3 +- include/asm-blackfin/mach-bf527/anomaly.h | 8 + include/asm-blackfin/mach-bf527/bf527.h | 127 ++ .../asm-blackfin/mach-bf527/bfin_serial_5xx.h | 152 ++ include/asm-blackfin/mach-bf527/blackfin.h | 78 ++ .../asm-blackfin/mach-bf527/cdefBF52x_base.h | 19 +- include/asm-blackfin/mach-bf527/defBF527.h | 4 +- .../asm-blackfin/mach-bf527/defBF52x_base.h | 9 +- include/asm-blackfin/mach-bf527/dma.h | 60 + include/asm-blackfin/mach-bf527/irq.h | 263 ++++ include/asm-blackfin/mach-bf527/mem_init.h | 337 +++++ include/asm-blackfin/mach-bf527/mem_map.h | 98 ++ include/asm-blackfin/mach-bf527/portmux.h | 205 +++ 29 files changed, 4590 insertions(+), 37 deletions(-) create mode 100644 arch/blackfin/configs/BF527-EZKIT_defconfig create mode 100644 arch/blackfin/mach-bf527/Kconfig create mode 100644 arch/blackfin/mach-bf527/Makefile create mode 100644 arch/blackfin/mach-bf527/boards/Makefile create mode 100644 arch/blackfin/mach-bf527/boards/eth_mac.c create mode 100644 arch/blackfin/mach-bf527/boards/ezkit.c create mode 100644 arch/blackfin/mach-bf527/cpu.c create mode 100644 arch/blackfin/mach-bf527/dma.c create mode 100644 arch/blackfin/mach-bf527/head.S create mode 100644 arch/blackfin/mach-bf527/ints-priority.c create mode 100644 include/asm-blackfin/mach-bf527/bf527.h create mode 100644 include/asm-blackfin/mach-bf527/bfin_serial_5xx.h create mode 100644 include/asm-blackfin/mach-bf527/blackfin.h create mode 100644 include/asm-blackfin/mach-bf527/dma.h create mode 100644 include/asm-blackfin/mach-bf527/irq.h create mode 100644 include/asm-blackfin/mach-bf527/mem_init.h create mode 100644 include/asm-blackfin/mach-bf527/mem_map.h create mode 100644 include/asm-blackfin/mach-bf527/portmux.h diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig index ad28dc76fc9..17830535099 100644 --- a/arch/blackfin/Kconfig +++ b/arch/blackfin/Kconfig @@ -71,7 +71,7 @@ config GENERIC_CALIBRATE_DELAY config IRQCHIP_DEMUX_GPIO bool - depends on (BF53x || BF561 || BF54x) + depends on (BF52x || BF53x || BF561 || BF54x) default y source "init/Kconfig" @@ -85,6 +85,21 @@ choice prompt "CPU" default BF533 +config BF522 + bool "BF522" + help + BF522 Processor Support. + +config BF525 + bool "BF525" + help + BF525 Processor Support. + +config BF527 + bool "BF527" + help + BF527 Processor Support. + config BF531 bool "BF531" help @@ -144,13 +159,18 @@ endchoice choice prompt "Silicon Rev" + default BF_REV_0_1 if BF527 default BF_REV_0_2 if BF537 default BF_REV_0_3 if BF533 default BF_REV_0_0 if BF549 config BF_REV_0_0 bool "0.0" - depends on (BF549) + depends on (BF549 || BF527) + +config BF_REV_0_1 + bool "0.2" + depends on (BF549 || BF527) config BF_REV_0_2 bool "0.2" @@ -176,6 +196,11 @@ config BF_REV_NONE endchoice +config BF52x + bool + depends on (BF522 || BF525 || BF527) + default y + config BF53x bool depends on (BF531 || BF532 || BF533 || BF534 || BF536 || BF537) @@ -204,6 +229,12 @@ choice configuration to ensure that all the other settings are correct. +config BFIN527_EZKIT + bool "BF527-EZKIT" + depends on (BF522 || BF525 || BF527) + help + BF533-EZKIT-LITE board Support. + config BFIN533_EZKIT bool "BF533-EZKIT" depends on (BF533 || BF532 || BF531) @@ -299,11 +330,17 @@ config MEM_MT48LC8M32B2B5_7 depends on (BFIN561_BLUETECHNIX_CM) default y +config MEM_MT48LC32M16A2TG_75 + bool + depends on (BFIN527_EZKIT) + default y + config BFIN_SHARED_FLASH_ENET bool depends on (BFIN533_STAMP) default y +source "arch/blackfin/mach-bf527/Kconfig" source "arch/blackfin/mach-bf533/Kconfig" source "arch/blackfin/mach-bf561/Kconfig" source "arch/blackfin/mach-bf537/Kconfig" @@ -329,7 +366,7 @@ config CLKIN_HZ int "Crystal Frequency in Hz" default "11059200" if BFIN533_STAMP default "27000000" if BFIN533_EZKIT - default "25000000" if BFIN537_STAMP + default "25000000" if (BFIN537_STAMP || BFIN527_EZKIT) default "30000000" if BFIN561_EZKIT default "24576000" if PNAV10 help @@ -362,7 +399,7 @@ config VCO_MULT range 1 64 default "22" if BFIN533_EZKIT default "45" if BFIN533_STAMP - default "20" if BFIN537_STAMP + default "20" if (BFIN537_STAMP || BFIN527_EZKIT) default "22" if BFIN533_BLUETECHNIX_CM default "20" if BFIN537_BLUETECHNIX_CM default "20" if BFIN561_BLUETECHNIX_CM @@ -398,7 +435,7 @@ config SCLK_DIV range 1 15 default 5 if BFIN533_EZKIT default 5 if BFIN533_STAMP - default 4 if BFIN537_STAMP + default 4 if (BFIN537_STAMP || BFIN527_EZKIT) default 5 if BFIN533_BLUETECHNIX_CM default 4 if BFIN537_BLUETECHNIX_CM default 4 if BFIN561_BLUETECHNIX_CM @@ -450,6 +487,7 @@ comment "Memory Setup" config MEM_SIZE int "SDRAM Memory Size in MBytes" default 32 if BFIN533_EZKIT + default 64 if BFIN527_EZKIT default 64 if BFIN537_STAMP default 64 if BFIN561_EZKIT default 128 if BFIN533_STAMP @@ -459,6 +497,7 @@ config MEM_ADD_WIDTH int "SDRAM Memory Address Width" default 9 if BFIN533_EZKIT default 9 if BFIN561_EZKIT + default 10 if BFIN527_EZKIT default 10 if BFIN537_STAMP default 11 if BFIN533_STAMP default 10 if PNAV10 @@ -751,7 +790,7 @@ config LARGE_ALLOCS config BFIN_DMA_5XX bool "Enable DMA Support" - depends on (BF533 || BF532 || BF531 || BF537 || BF536 || BF534 || BF561 || BF54x) + depends on (BF52x || BF53x || BF561 || BF54x) default y help DMA driver for BF5xx. diff --git a/arch/blackfin/Makefile b/arch/blackfin/Makefile index 368933760d2..d80421c7b30 100644 --- a/arch/blackfin/Makefile +++ b/arch/blackfin/Makefile @@ -18,6 +18,9 @@ KALLSYMS += --symbol-prefix=_ KBUILD_DEFCONFIG := BF537-STAMP_defconfig # setup the machine name and the machine dependent settings +machine-$(CONFIG_BF522) := bf527 +machine-$(CONFIG_BF525) := bf527 +machine-$(CONFIG_BF527) := bf527 machine-$(CONFIG_BF531) := bf533 machine-$(CONFIG_BF532) := bf533 machine-$(CONFIG_BF533) := bf533 @@ -32,6 +35,9 @@ machine-$(CONFIG_BF561) := bf561 MACHINE := $(machine-y) export MACHINE +cpu-$(CONFIG_BF522) := bf522 +cpu-$(CONFIG_BF525) := bf525 +cpu-$(CONFIG_BF527) := bf527 cpu-$(CONFIG_BF531) := bf531 cpu-$(CONFIG_BF532) := bf532 cpu-$(CONFIG_BF533) := bf533 diff --git a/arch/blackfin/configs/BF527-EZKIT_defconfig b/arch/blackfin/configs/BF527-EZKIT_defconfig new file mode 100644 index 00000000000..df974e785ee --- /dev/null +++ b/arch/blackfin/configs/BF527-EZKIT_defconfig @@ -0,0 +1,1241 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.22.9 +# +# CONFIG_MMU is not set +# CONFIG_FPU is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set +CONFIG_BLACKFIN=y +CONFIG_ZONE_DMA=y +CONFIG_BFIN=y +CONFIG_SEMAPHORE_SLEEPERS=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_HARDIRQS=y +CONFIG_GENERIC_IRQ_PROBE=y +# CONFIG_GENERIC_TIME is not set +CONFIG_GENERIC_GPIO=y +CONFIG_FORCE_MAX_ZONEORDER=14 +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_IRQCHIP_DEMUX_GPIO=y +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# Code maturity level options +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 + +# +# General setup +# +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SYSVIPC=y +# CONFIG_IPC_NS is not set +CONFIG_SYSVIPC_SYSCTL=y +# CONFIG_POSIX_MQUEUE is not set +# CONFIG_BSD_PROCESS_ACCT is not set +# CONFIG_TASKSTATS is not set +# CONFIG_UTS_NS is not set +# CONFIG_AUDIT is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_LOG_BUF_SHIFT=14 +CONFIG_SYSFS_DEPRECATED=y +# CONFIG_RELAY is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +CONFIG_SYSCTL_SYSCALL=y +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_EXTRA_PASS is not set +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_EVENTFD=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_BIG_ORDER_ALLOC_NOFAIL_MAGIC=3 +# CONFIG_NP2 is not set +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +CONFIG_RT_MUTEXES=y +CONFIG_TINY_SHMEM=y +CONFIG_BASE_SMALL=0 + +# +# Loadable module support +# +CONFIG_MODULES=y +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +# CONFIG_MODVERSIONS is not set +# CONFIG_MODULE_SRCVERSION_ALL is not set +CONFIG_KMOD=y + +# +# Block layer +# +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +# CONFIG_IOSCHED_DEADLINE is not set +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +# CONFIG_PREEMPT_NONE is not set +CONFIG_PREEMPT_VOLUNTARY=y +# CONFIG_PREEMPT is not set + +# +# Blackfin Processor Options +# + +# +# Processor and Board Settings +# +# CONFIG_BF522 is not set +# CONFIG_BF525 is not set +CONFIG_BF527=y +# CONFIG_BF531 is not set +# CONFIG_BF532 is not set +# CONFIG_BF533 is not set +# CONFIG_BF534 is not set +# CONFIG_BF536 is not set +# CONFIG_BF537 is not set +# CONFIG_BF542 is not set +# CONFIG_BF544 is not set +# CONFIG_BF548 is not set +# CONFIG_BF549 is not set +# CONFIG_BF561 is not set +CONFIG_BF_REV_0_0=y +# CONFIG_BF_REV_0_1 is not set +# CONFIG_BF_REV_0_2 is not set +# CONFIG_BF_REV_0_3 is not set +# CONFIG_BF_REV_0_4 is not set +# CONFIG_BF_REV_0_5 is not set +# CONFIG_BF_REV_ANY is not set +# CONFIG_BF_REV_NONE is not set +CONFIG_BF52x=y +CONFIG_BFIN_SINGLE_CORE=y +CONFIG_BFIN527_EZKIT=y +# CONFIG_BFIN533_EZKIT is not set +# CONFIG_BFIN533_STAMP is not set +# CONFIG_BFIN537_STAMP is not set +# CONFIG_BFIN533_BLUETECHNIX_CM is not set +# CONFIG_BFIN537_BLUETECHNIX_CM is not set +# CONFIG_BFIN548_EZKIT is not set +# CONFIG_BFIN561_BLUETECHNIX_CM is not set +# CONFIG_BFIN561_EZKIT is not set +# CONFIG_BFIN561_TEPLA is not set +# CONFIG_PNAV10 is not set +# CONFIG_GENERIC_BOARD is not set +CONFIG_MEM_MT48LC32M16A2TG_75=y + +# +# BF527 Specific Configuration +# + +# +# Alternative Multiplexing Scheme +# +# CONFIG_BF527_SPORT0_PORTF is not set +CONFIG_BF527_SPORT0_PORTG=y +CONFIG_BF527_SPORT0_TSCLK_PG10=y +# CONFIG_BF527_SPORT0_TSCLK_PG14 is not set +# CONFIG_BF527_UART1_PORTF is not set +CONFIG_BF527_UART1_PORTG=y +# CONFIG_BF527_NAND_D_PORTF is not set +CONFIG_BF527_NAND_D_PORTH=y + +# +# Interrupt Priority Assignment +# + +# +# Priority +# +CONFIG_IRQ_PLL_WAKEUP=7 +CONFIG_IRQ_DMA0_ERROR=7 +CONFIG_IRQ_DMAR0_BLK=7 +CONFIG_IRQ_DMAR1_BLK=7 +CONFIG_IRQ_DMAR0_OVR=7 +CONFIG_IRQ_DMAR1_OVR=7 +CONFIG_IRQ_PPI_ERROR=7 +CONFIG_IRQ_MAC_ERROR=7 +CONFIG_IRQ_SPORT0_ERROR=7 +CONFIG_IRQ_SPORT1_ERROR=7 +CONFIG_IRQ_UART0_ERROR=7 +CONFIG_IRQ_UART1_ERROR=7 +CONFIG_IRQ_RTC=8 +CONFIG_IRQ_PPI=8 +CONFIG_IRQ_SPORT0_RX=9 +CONFIG_IRQ_SPORT0_TX=9 +CONFIG_IRQ_SPORT1_RX=9 +CONFIG_IRQ_SPORT1_TX=9 +CONFIG_IRQ_TWI=10 +CONFIG_IRQ_SPI=10 +CONFIG_IRQ_UART0_RX=10 +CONFIG_IRQ_UART0_TX=10 +CONFIG_IRQ_UART1_RX=10 +CONFIG_IRQ_UART1_TX=10 +CONFIG_IRQ_OPTSEC=11 +CONFIG_IRQ_CNT=11 +CONFIG_IRQ_MAC_RX=11 +CONFIG_IRQ_PORTH_INTA=11 +CONFIG_IRQ_MAC_TX=11 +CONFIG_IRQ_PORTH_INTB=11 +CONFIG_IRQ_TMR0=12 +CONFIG_IRQ_TMR1=12 +CONFIG_IRQ_TMR2=12 +CONFIG_IRQ_TMR3=12 +CONFIG_IRQ_TMR4=12 +CONFIG_IRQ_TMR5=12 +CONFIG_IRQ_TMR6=12 +CONFIG_IRQ_TMR7=12 +CONFIG_IRQ_PORTG_INTA=12 +CONFIG_IRQ_PORTG_INTB=12 +CONFIG_IRQ_MEM_DMA0=13 +CONFIG_IRQ_MEM_DMA1=13 +CONFIG_IRQ_WATCH=13 +CONFIG_IRQ_PORTF_INTA=13 +CONFIG_IRQ_PORTF_INTB=13 +CONFIG_IRQ_SPI_ERROR=7 +CONFIG_IRQ_NFC_ERROR=7 +CONFIG_IRQ_HDMA_ERROR=7 +CONFIG_IRQ_HDMA=7 +CONFIG_IRQ_USB_EINT=10 +CONFIG_IRQ_USB_INT0=11 +CONFIG_IRQ_USB_INT1=11 +CONFIG_IRQ_USB_INT2=11 +CONFIG_IRQ_USB_DMA=11 + +# +# Board customizations +# +# CONFIG_CMDLINE_BOOL is not set + +# +# Clock/PLL Setup +# +CONFIG_CLKIN_HZ=25000000 +# CONFIG_BFIN_KERNEL_CLOCK is not set +CONFIG_MAX_VCO_HZ=600000000 +CONFIG_MIN_VCO_HZ=50000000 +CONFIG_MAX_SCLK_HZ=133000000 +CONFIG_MIN_SCLK_HZ=27000000 + +# +# Kernel Timer/Scheduler +# +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_HZ_300 is not set +# CONFIG_HZ_1000 is not set +CONFIG_HZ=250 + +# +# Memory Setup +# +CONFIG_MEM_SIZE=64 +CONFIG_MEM_ADD_WIDTH=10 +CONFIG_BOOT_LOAD=0x1000 +CONFIG_BFIN_SCRATCH_REG_RETN=y +# CONFIG_BFIN_SCRATCH_REG_RETE is not set +# CONFIG_BFIN_SCRATCH_REG_CYCLES is not set + +# +# Blackfin Kernel Optimizations +# + +# +# Memory Optimizations +# +CONFIG_I_ENTRY_L1=y +CONFIG_EXCPT_IRQ_SYSC_L1=y +CONFIG_DO_IRQ_L1=y +CONFIG_CORE_TIMER_IRQ_L1=y +CONFIG_IDLE_L1=y +# CONFIG_SCHEDULE_L1 is not set +CONFIG_ARITHMETIC_OPS_L1=y +CONFIG_ACCESS_OK_L1=y +# CONFIG_MEMSET_L1 is not set +# CONFIG_MEMCPY_L1 is not set +# CONFIG_SYS_BFIN_SPINLOCK_L1 is not set +# CONFIG_IP_CHECKSUM_L1 is not set +CONFIG_CACHELINE_ALIGNED_L1=y +# CONFIG_SYSCALL_TAB_L1 is not set +# CONFIG_CPLB_SWITCH_TAB_L1 is not set +CONFIG_RAMKERNEL=y +# CONFIG_ROMKERNEL is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_LARGE_ALLOCS=y +CONFIG_BFIN_DMA_5XX=y +# CONFIG_DMA_UNCACHED_2M is not set +CONFIG_DMA_UNCACHED_1M=y +# CONFIG_DMA_UNCACHED_NONE is not set + +# +# Cache Support +# +CONFIG_BFIN_ICACHE=y +CONFIG_BFIN_DCACHE=y +# CONFIG_BFIN_DCACHE_BANKA is not set +# CONFIG_BFIN_ICACHE_LOCK is not set +# CONFIG_BFIN_WB is not set +CONFIG_BFIN_WT=y +CONFIG_L1_MAX_PIECE=16 + +# +# Asynchonous Memory Configuration +# + +# +# EBIU_AMBCTL Global Control +# +CONFIG_C_AMCKEN=y +CONFIG_C_CDPRIO=y +# CONFIG_C_AMBEN is not set +# CONFIG_C_AMBEN_B0 is not set +# CONFIG_C_AMBEN_B0_B1 is not set +# CONFIG_C_AMBEN_B0_B1_B2 is not set +CONFIG_C_AMBEN_ALL=y + +# +# EBIU_AMBCTL Control +# +CONFIG_BANK_0=0x7BB0 +CONFIG_BANK_1=0x5554 +CONFIG_BANK_2=0x7BB0 +CONFIG_BANK_3=0xFFC0 + +# +# Bus options (PCI, PCMCIA, EISA, MCA, ISA) +# +# CONFIG_PCI is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set + +# +# PCCARD (PCMCIA/CardBus) support +# +# CONFIG_PCCARD is not set + +# +# Executable file formats +# +CONFIG_BINFMT_ELF_FDPIC=y +CONFIG_BINFMT_FLAT=y +CONFIG_BINFMT_ZFLAT=y +# CONFIG_BINFMT_SHARED_FLAT is not set +# CONFIG_BINFMT_MISC is not set + +# +# Power management options +# +# CONFIG_PM is not set + +# +# Networking +# +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +# CONFIG_XFRM_USER is not set +# CONFIG_XFRM_SUB_POLICY is not set +# CONFIG_XFRM_MIGRATE is not set +# CONFIG_NET_KEY is not set +CONFIG_INET=y +# CONFIG_IP_MULTICAST is not set +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +# CONFIG_IP_PNP_DHCP is not set +# CONFIG_IP_PNP_BOOTP is not set +# CONFIG_IP_PNP_RARP is not set +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_ARPD is not set +CONFIG_SYN_COOKIES=y +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_INET6_XFRM_TUNNEL is not set +# CONFIG_INET6_TUNNEL is not set +# CONFIG_NETLABEL is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set + +# +# QoS and/or fair queueing +# +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set + +# +# Wireless +# +# CONFIG_CFG80211 is not set +# CONFIG_WIRELESS_EXT is not set +# CONFIG_MAC80211 is not set +# CONFIG_IEEE80211 is not set +# CONFIG_RFKILL is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_SYS_HYPERVISOR is not set + +# +# Connector - unified userspace <-> kernelspace linker +# +# CONFIG_CONNECTOR is not set +CONFIG_MTD=y +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_CONCAT is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_CMDLINE_PARTS is not set + +# +# User Modules And Translation Layers +# +CONFIG_MTD_CHAR=m +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_FTL is not set +# CONFIG_NFTL is not set +# CONFIG_INFTL is not set +# CONFIG_RFD_FTL is not set +# CONFIG_SSFDC is not set + +# +# RAM/ROM/Flash chip drivers +# +# CONFIG_MTD_CFI is not set +CONFIG_MTD_JEDECPROBE=m +CONFIG_MTD_GEN_PROBE=m +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +CONFIG_MTD_MAP_BANK_WIDTH_2=y +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_AMDSTD is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_MW320D=m +CONFIG_MTD_RAM=y +CONFIG_MTD_ROM=m +# CONFIG_MTD_ABSENT is not set + +# +# Mapping drivers for chip access +# +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_PHYSMAP is not set +CONFIG_MTD_BF5xx=m +CONFIG_BFIN_FLASH_SIZE=0x400000 +CONFIG_EBIU_FLASH_BASE=0x20000000 +# CONFIG_MTD_UCLINUX is not set +# CONFIG_MTD_PLATRAM is not set + +# +# Self-contained MTD device drivers +# +# CONFIG_MTD_DATAFLASH is not set +# CONFIG_MTD_M25P80 is not set +# CONFIG_MTD_SLRAM is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_BLOCK2MTD is not set + +# +# Disk-On-Chip Device Drivers +# +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_NAND=m +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +CONFIG_MTD_NAND_BFIN=m +CONFIG_BFIN_NAND_BASE=0x20212000 +CONFIG_BFIN_NAND_CLE=2 +CONFIG_BFIN_NAND_ALE=1 +CONFIG_BFIN_NAND_READY=3 +CONFIG_MTD_NAND_IDS=m +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_NANDSIM is not set +# CONFIG_MTD_NAND_PLATFORM is not set +# CONFIG_MTD_ONENAND is not set + +# +# UBI - Unsorted block images +# +# CONFIG_MTD_UBI is not set + +# +# Parallel port support +# +# CONFIG_PARPORT is not set + +# +# Plug and Play support +# +# CONFIG_PNPACPI is not set + +# +# Block devices +# +# CONFIG_BLK_DEV_COW_COMMON is not set +# CONFIG_BLK_DEV_LOOP is not set +# CONFIG_BLK_DEV_NBD is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024 +# CONFIG_CDROM_PKTCDVD is not set +# CONFIG_ATA_OVER_ETH is not set + +# +# Misc devices +# +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +# CONFIG_SCSI is not set +# CONFIG_SCSI_NETLINK is not set +# CONFIG_ATA is not set + +# +# Multi-device support (RAID and LVM) +# +# CONFIG_MD is not set + +# +# Network device support +# +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +# CONFIG_SMSC_PHY is not set +# CONFIG_BROADCOM_PHY is not set +# CONFIG_FIXED_PHY is not set + +# +# Ethernet (10 or 100Mbit) +# +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_SMC91X is not set +CONFIG_BFIN_MAC=y +CONFIG_BFIN_MAC_USE_L1=y +CONFIG_BFIN_TX_DESC_NUM=10 +CONFIG_BFIN_RX_DESC_NUM=20 +CONFIG_BFIN_MAC_RMII=y +# CONFIG_SMSC911X is not set +# CONFIG_DM9000 is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_SHAPER is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set + +# +# ISDN subsystem +# +# CONFIG_ISDN is not set + +# +# Telephony Support +# +# CONFIG_PHONE is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +# CONFIG_INPUT_TSDEV is not set +# CONFIG_INPUT_EVDEV is not set +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +# CONFIG_INPUT_TOUCHSCREEN is not set +CONFIG_INPUT_MISC=y +# CONFIG_INPUT_ATI_REMOTE is not set +# CONFIG_INPUT_ATI_REMOTE2 is not set +# CONFIG_INPUT_KEYSPAN_REMOTE is not set +# CONFIG_INPUT_POWERMATE is not set +# CONFIG_INPUT_YEALINK is not set +# CONFIG_INPUT_UINPUT is not set +# CONFIG_BF53X_PFBUTTONS is not set +# CONFIG_TWI_KEYPAD is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +# CONFIG_AD9960 is not set +# CONFIG_SPI_ADC_BF533 is not set +# CONFIG_BF5xx_PFLAGS is not set +# CONFIG_BF5xx_PPIFCD is not set +# CONFIG_BF5xx_TIMERS is not set +# CONFIG_BF5xx_PPI is not set +# CONFIG_BFIN_SPORT is not set +# CONFIG_BFIN_TIMER_LATENCY is not set +# CONFIG_TWI_LCD is not set +# CONFIG_AD5304 is not set +# CONFIG_BF5xx_TEA5764 is not set +# CONFIG_BF5xx_FBDMA is not set +# CONFIG_VT is not set +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +# CONFIG_SERIAL_8250 is not set + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_BFIN=y +CONFIG_SERIAL_BFIN_CONSOLE=y +# CONFIG_SERIAL_BFIN_DMA is not set +CONFIG_SERIAL_BFIN_PIO=y +# CONFIG_SERIAL_BFIN_UART0 is not set +CONFIG_SERIAL_BFIN_UART1=y +# CONFIG_BFIN_UART1_CTSRTS is not set +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +# CONFIG_SERIAL_BFIN_SPORT is not set +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set + +# +# CAN, the car bus and industrial fieldbus +# +# CONFIG_CAN4LINUX is not set + +# +# IPMI +# +# CONFIG_IPMI_HANDLER is not set +CONFIG_WATCHDOG=y +# CONFIG_WATCHDOG_NOWAYOUT is not set + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set +CONFIG_BFIN_WDT=y +CONFIG_HW_RANDOM=y +# CONFIG_GEN_RTC is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set + +# +# TPM devices +# +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=m + +# +# I2C Algorithms +# +# CONFIG_I2C_ALGOBIT is not set +# CONFIG_I2C_ALGOPCF is not set +# CONFIG_I2C_ALGOPCA is not set + +# +# I2C Hardware Bus support +# +# CONFIG_I2C_BLACKFIN_GPIO is not set +CONFIG_I2C_BLACKFIN_TWI=m +CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ=50 +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_SIMTEC is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_SENSORS_DS1337 is not set +# CONFIG_SENSORS_DS1374 is not set +# CONFIG_SENSORS_AD5252 is not set +# CONFIG_SENSORS_EEPROM is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_SENSORS_PCF8575 is not set +# CONFIG_SENSORS_PCA9543 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set + +# +# SPI support +# +CONFIG_SPI=y +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +CONFIG_SPI_BFIN=y +# CONFIG_SPI_BITBANG is not set + +# +# SPI Protocol Masters +# +# CONFIG_SPI_AT25 is not set +# CONFIG_SPI_SPIDEV is not set + +# +# Dallas's 1-wire bus +# +# CONFIG_W1 is not set +CONFIG_HWMON=y +# CONFIG_HWMON_VID is not set +# CONFIG_SENSORS_ABITUGURU is not set +# CONFIG_SENSORS_AD7418 is not set +# CONFIG_SENSORS_ADM1021 is not set +# CONFIG_SENSORS_ADM1025 is not set +# CONFIG_SENSORS_ADM1026 is not set +# CONFIG_SENSORS_ADM1029 is not set +# CONFIG_SENSORS_ADM1031 is not set +# CONFIG_SENSORS_ADM9240 is not set +# CONFIG_SENSORS_ASB100 is not set +# CONFIG_SENSORS_ATXP1 is not set +# CONFIG_SENSORS_DS1621 is not set +# CONFIG_SENSORS_F71805F is not set +# CONFIG_SENSORS_FSCHER is not set +# CONFIG_SENSORS_FSCPOS is not set +# CONFIG_SENSORS_GL518SM is not set +# CONFIG_SENSORS_GL520SM is not set +# CONFIG_SENSORS_IT87 is not set +# CONFIG_SENSORS_LM63 is not set +# CONFIG_SENSORS_LM70 is not set +# CONFIG_SENSORS_LM75 is not set +# CONFIG_SENSORS_LM77 is not set +# CONFIG_SENSORS_LM78 is not set +# CONFIG_SENSORS_LM80 is not set +# CONFIG_SENSORS_LM83 is not set +# CONFIG_SENSORS_LM85 is not set +# CONFIG_SENSORS_LM87 is not set +# CONFIG_SENSORS_LM90 is not set +# CONFIG_SENSORS_LM92 is not set +# CONFIG_SENSORS_MAX1619 is not set +# CONFIG_SENSORS_MAX6650 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SENSORS_PC87427 is not set +# CONFIG_SENSORS_SMSC47M1 is not set +# CONFIG_SENSORS_SMSC47M192 is not set +# CONFIG_SENSORS_SMSC47B397 is not set +# CONFIG_SENSORS_VT1211 is not set +# CONFIG_SENSORS_W83781D is not set +# CONFIG_SENSORS_W83791D is not set +# CONFIG_SENSORS_W83792D is not set +# CONFIG_SENSORS_W83793 is not set +# CONFIG_SENSORS_W83L785TS is not set +# CONFIG_SENSORS_W83627HF is not set +# CONFIG_SENSORS_W83627EHF is not set +# CONFIG_HWMON_DEBUG_CHIP is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_SM501 is not set + +# +# Multimedia devices +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_DVB_CORE is not set +# CONFIG_DAB is not set + +# +# Graphics support +# +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set +# CONFIG_VGASTATE is not set +# CONFIG_FB is not set + +# +# Sound +# +# CONFIG_SOUND is not set + +# +# HID Devices +# +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set + +# +# USB support +# +CONFIG_USB_ARCH_HAS_HCD=y +# CONFIG_USB_ARCH_HAS_OHCI is not set +# CONFIG_USB_ARCH_HAS_EHCI is not set +# CONFIG_USB is not set + +# +# Enable Host or Gadget support to see Inventra options +# + +# +# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support' +# + +# +# USB Gadget Support +# +# CONFIG_USB_GADGET is not set +# CONFIG_MMC is not set + +# +# LED devices +# +# CONFIG_NEW_LEDS is not set + +# +# LED drivers +# + +# +# LED Triggers +# + +# +# InfiniBand support +# + +# +# EDAC - error detection and reporting (RAS) (EXPERIMENTAL) +# + +# +# Real Time Clock +# +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_RS5C348 is not set +# CONFIG_RTC_DRV_MAX6902 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +CONFIG_RTC_DRV_BFIN=y + +# +# DMA Engine support +# +# CONFIG_DMA_ENGINE is not set + +# +# DMA Clients +# + +# +# DMA Devices +# + +# +# PBX support +# +# CONFIG_PBX is not set + +# +# File systems +# +# CONFIG_EXT2_FS is not set +# CONFIG_EXT3_FS is not set +# CONFIG_EXT4DEV_FS is not set +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +# CONFIG_GFS2_FS is not set +# CONFIG_OCFS2_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_ROMFS_FS is not set +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +# CONFIG_QUOTA is not set +# CONFIG_DNOTIFY is not set +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +# CONFIG_MSDOS_FS is not set +# CONFIG_VFAT_FS is not set +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +# CONFIG_TMPFS is not set +# CONFIG_HUGETLB_PAGE is not set +CONFIG_RAMFS=y +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +CONFIG_YAFFS_FS=m +CONFIG_YAFFS_YAFFS1=y +# CONFIG_YAFFS_DOES_ECC is not set +CONFIG_YAFFS_YAFFS2=y +CONFIG_YAFFS_AUTO_YAFFS2=y +# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set +CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=10 +# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set +# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set +CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y +CONFIG_JFFS2_FS=m +CONFIG_JFFS2_FS_DEBUG=0 +CONFIG_JFFS2_FS_WRITEBUFFER=y +# CONFIG_JFFS2_SUMMARY is not set +# CONFIG_JFFS2_FS_XATTR is not set +# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set +CONFIG_JFFS2_ZLIB=y +CONFIG_JFFS2_RTIME=y +# CONFIG_JFFS2_RUBIN is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set + +# +# Network File Systems +# +CONFIG_NFS_FS=m +CONFIG_NFS_V3=y +# CONFIG_NFS_V3_ACL is not set +# CONFIG_NFS_V4 is not set +# CONFIG_NFS_DIRECTIO is not set +# CONFIG_NFSD is not set +CONFIG_LOCKD=m +CONFIG_LOCKD_V4=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=m +# CONFIG_SUNRPC_BIND34 is not set +# CONFIG_RPCSEC_GSS_KRB5 is not set +# CONFIG_RPCSEC_GSS_SPKM3 is not set +CONFIG_SMB_FS=m +# CONFIG_SMB_NLS_DEFAULT is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set +# CONFIG_9P_FS is not set + +# +# Partition Types +# +# CONFIG_PARTITION_ADVANCED is not set +CONFIG_MSDOS_PARTITION=y + +# +# Native Language Support +# +CONFIG_NLS=m +CONFIG_NLS_DEFAULT="iso8859-1" +# CONFIG_NLS_CODEPAGE_437 is not set +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +# CONFIG_NLS_ISO8859_1 is not set +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Distributed Lock Manager +# +# CONFIG_DLM is not set + +# +# Profiling support +# +# CONFIG_PROFILING is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +CONFIG_DEBUG_FS=y +# CONFIG_HEADERS_CHECK is not set +# CONFIG_DEBUG_KERNEL is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_MMRS=y +CONFIG_DEBUG_HUNT_FOR_ZERO=y +CONFIG_DEBUG_BFIN_HWTRACE_ON=y +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_OFF=y +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_ONE is not set +# CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION_TWO is not set +CONFIG_DEBUG_BFIN_HWTRACE_COMPRESSION=0 +# CONFIG_DEBUG_BFIN_HWTRACE_EXPAND is not set +# CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE is not set +CONFIG_EARLY_PRINTK=y +CONFIG_CPLB_INFO=y +CONFIG_ACCESS_CHECK=y + +# +# Security options +# +# CONFIG_KEYS is not set +CONFIG_SECURITY=y +# CONFIG_SECURITY_NETWORK is not set +CONFIG_SECURITY_CAPABILITIES=y + +# +# Cryptographic options +# +# CONFIG_CRYPTO is not set + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_CRC_CCITT is not set +# CONFIG_CRC16 is not set +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_LIBCRC32C is not set +CONFIG_ZLIB_INFLATE=y +CONFIG_ZLIB_DEFLATE=m +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y diff --git a/arch/blackfin/kernel/bfin_gpio.c b/arch/blackfin/kernel/bfin_gpio.c index 3fe0cd49e8d..ce85d4bf34c 100644 --- a/arch/blackfin/kernel/bfin_gpio.c +++ b/arch/blackfin/kernel/bfin_gpio.c @@ -124,7 +124,7 @@ static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = { }; #endif -#ifdef BF537_FAMILY +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = { (struct gpio_port_t *) PORTFIO, (struct gpio_port_t *) PORTGIO, @@ -139,6 +139,21 @@ static unsigned short *port_fer[gpio_bank(MAX_BLACKFIN_GPIOS)] = { #endif +#ifdef BF527_FAMILY +static unsigned short *port_mux[gpio_bank(MAX_BLACKFIN_GPIOS)] = { + (unsigned short *) PORTF_MUX, + (unsigned short *) PORTG_MUX, + (unsigned short *) PORTH_MUX, +}; + +static const +u8 pmux_offset[][16] = + {{ 0, 0, 0, 0, 0, 0, 0, 0, 2, 2, 4, 6, 8, 8, 10, 10 }, /* PORTF */ + { 0, 0, 0, 0, 0, 2, 2, 4, 4, 6, 8, 10, 10, 10, 12, 12 }, /* PORTG */ + { 0, 0, 0, 0, 0, 0, 0, 0, 2, 4, 4, 4, 4, 4, 4, 4 }, /* PORTH */ + }; +#endif + #ifdef BF561_FAMILY static struct gpio_port_t *gpio_bankb[gpio_bank(MAX_BLACKFIN_GPIOS)] = { (struct gpio_port_t *) FIO0_FLAG_D, @@ -186,6 +201,10 @@ static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG_INTB, IRQ_PORTG_INTB, IRQ_MAC_TX}; #endif +#ifdef BF527_FAMILY +static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PORTF_INTB, IRQ_PORTG_INTB, IRQ_PORTH_INTB}; +#endif + #ifdef BF561_FAMILY static unsigned int sic_iwr_irqs[gpio_bank(MAX_BLACKFIN_GPIOS)] = {IRQ_PROG0_INTB, IRQ_PROG1_INTB, IRQ_PROG2_INTB}; #endif @@ -238,7 +257,7 @@ static int cmp_label(unsigned short ident, const char *label) return -EINVAL; } -#ifdef BF537_FAMILY +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) static void port_setup(unsigned short gpio, unsigned short usage) { if (!check_gpio(gpio)) { @@ -354,6 +373,18 @@ inline u16 get_portmux(unsigned short portno) return (pmux >> (2 * gpio_sub_n(portno)) & 0x3); } +#elif defined(BF527_FAMILY) +inline void portmux_setup(unsigned short portno, unsigned short function) +{ + u16 pmux, ident = P_IDENT(portno); + u8 offset = pmux_offset[gpio_bank(ident)][gpio_sub_n(ident)]; + + pmux = *port_mux[gpio_bank(ident)]; + pmux &= ~(3 << offset); + pmux |= (function & 3) << offset; + *port_mux[gpio_bank(ident)] = pmux; + SSYNC(); +} #else # define portmux_setup(...) do { } while (0) #endif diff --git a/arch/blackfin/kernel/reboot.c b/arch/blackfin/kernel/reboot.c index 356078ec462..ae28aac6fec 100644 --- a/arch/blackfin/kernel/reboot.c +++ b/arch/blackfin/kernel/reboot.c @@ -11,7 +11,7 @@ #include #include -#if defined(BF537_FAMILY) || defined(BF533_FAMILY) +#if defined(BF537_FAMILY) || defined(BF533_FAMILY) || defined(BF527_FAMILY) #define SYSCR_VAL 0x0 #elif defined(BF561_FAMILY) #define SYSCR_VAL 0x20 diff --git a/arch/blackfin/mach-bf527/Kconfig b/arch/blackfin/mach-bf527/Kconfig new file mode 100644 index 00000000000..50321f723de --- /dev/null +++ b/arch/blackfin/mach-bf527/Kconfig @@ -0,0 +1,251 @@ +if (BF52x) + +menu "BF527 Specific Configuration" + +comment "Alternative Multiplexing Scheme" + +choice + prompt "SPORT0" + default BF527_SPORT0_PORTG + help + Select PORT used for SPORT0. See Hardware Reference Manual + +config BF527_SPORT0_PORTF + bool "PORT F" + help + PORT F + +config BF527_SPORT0_PORTG + bool "PORT G" + help + PORT G +endchoice + +choice + prompt "SPORT0 TSCLK Location" + depends on BF527_SPORT0_PORTG + default BF527_SPORT0_TSCLK_PG10 + help + Select PIN used for SPORT0_TSCLK. See Hardware Reference Manual + +config BF527_SPORT0_TSCLK_PG10 + bool "PORT PG10" + help + PORT PG10 + +config BF527_SPORT0_TSCLK_PG14 + bool "PORT PG14" + help + PORT PG14 +endchoice + +choice + prompt "UART1" + default BF527_UART1_PORTG + help + Select PORT used for UART1. See Hardware Reference Manual + +config BF527_UART1_PORTF + bool "PORT F" + help + PORT F + +config BF527_UART1_PORTG + bool "PORT G" + help + PORT G +endchoice + +choice + prompt "NAND (NFC) Data" + default BF527_NAND_D_PORTH + help + Select PORT used for NAND Data Bus. See Hardware Reference Manual + +config BF527_NAND_D_PORTF + bool "PORT F" + help + PORT F + +config BF527_NAND_D_PORTH + bool "PORT H" + help + PORT H +endchoice + +comment "Interrupt Priority Assignment" +menu "Priority" + +config IRQ_PLL_WAKEUP + int "IRQ_PLL_WAKEUP" + default 7 +config IRQ_DMA0_ERROR + int "IRQ_DMA0_ERROR" + default 7 +config IRQ_DMAR0_BLK + int "IRQ_DMAR0_BLK" + default 7 +config IRQ_DMAR1_BLK + int "IRQ_DMAR1_BLK" + default 7 +config IRQ_DMAR0_OVR + int "IRQ_DMAR0_OVR" + default 7 +config IRQ_DMAR1_OVR + int "IRQ_DMAR1_OVR" + default 7 +config IRQ_PPI_ERROR + int "IRQ_PPI_ERROR" + default 7 +config IRQ_MAC_ERROR + int "IRQ_MAC_ERROR" + default 7 +config IRQ_SPORT0_ERROR + int "IRQ_SPORT0_ERROR" + default 7 +config IRQ_SPORT1_ERROR + int "IRQ_SPORT1_ERROR" + default 7 +config IRQ_UART0_ERROR + int "IRQ_UART0_ERROR" + default 7 +config IRQ_UART1_ERROR + int "IRQ_UART1_ERROR" + default 7 +config IRQ_RTC + int "IRQ_RTC" + default 8 +config IRQ_PPI + int "IRQ_PPI" + default 8 +config IRQ_SPORT0_RX + int "IRQ_SPORT0_RX" + default 9 +config IRQ_SPORT0_TX + int "IRQ_SPORT0_TX" + default 9 +config IRQ_SPORT1_RX + int "IRQ_SPORT1_RX" + default 9 +config IRQ_SPORT1_TX + int "IRQ_SPORT1_TX" + default 9 +config IRQ_TWI + int "IRQ_TWI" + default 10 +config IRQ_SPI + int "IRQ_SPI" + default 10 +config IRQ_UART0_RX + int "IRQ_UART0_RX" + default 10 +config IRQ_UART0_TX + int "IRQ_UART0_TX" + default 10 +config IRQ_UART1_RX + int "IRQ_UART1_RX" + default 10 +config IRQ_UART1_TX + int "IRQ_UART1_TX" + default 10 +config IRQ_OPTSEC + int "IRQ_OPTSEC" + default 11 +config IRQ_CNT + int "IRQ_CNT" + default 11 +config IRQ_MAC_RX + int "IRQ_MAC_RX" + default 11 +config IRQ_PORTH_INTA + int "IRQ_PORTH_INTA" + default 11 +config IRQ_MAC_TX + int "IRQ_MAC_TX/NFC" + default 11 +config IRQ_PORTH_INTB + int "IRQ_PORTH_INTB" + default 11 +config IRQ_TMR0 + int "IRQ_TMR0" + default 12 +config IRQ_TMR1 + int "IRQ_TMR1" + default 12 +config IRQ_TMR2 + int "IRQ_TMR2" + default 12 +config IRQ_TMR3 + int "IRQ_TMR3" + default 12 +config IRQ_TMR4 + int "IRQ_TMR4" + default 12 +config IRQ_TMR5 + int "IRQ_TMR5" + default 12 +config IRQ_TMR6 + int "IRQ_TMR6" + default 12 +config IRQ_TMR7 + int "IRQ_TMR7" + default 12 +config IRQ_PORTG_INTA + int "IRQ_PORTG_INTA" + default 12 +config IRQ_PORTG_INTB + int "IRQ_PORTG_INTB" + default 12 +config IRQ_MEM_DMA0 + int "IRQ_MEM_DMA0" + default 13 +config IRQ_MEM_DMA1 + int "IRQ_MEM_DMA1" + default 13 +config IRQ_WATCH + int "IRQ_WATCH" + default 13 +config IRQ_PORTF_INTA + int "IRQ_PORTF_INTA" + default 13 +config IRQ_PORTF_INTB + int "IRQ_PORTF_INTB" + default 13 +config IRQ_SPI_ERROR + int "IRQ_SPI_ERROR" + default 7 +config IRQ_NFC_ERROR + int "IRQ_NFC_ERROR" + default 7 +config IRQ_HDMA_ERROR + int "IRQ_HDMA_ERROR" + default 7 +config IRQ_HDMA + int "IRQ_HDMA" + default 7 +config IRQ_USB_EINT + int "IRQ_USB_EINT" + default 10 +config IRQ_USB_INT0 + int "IRQ_USB_INT0" + default 10 +config IRQ_USB_INT1 + int "IRQ_USB_INT1" + default 10 +config IRQ_USB_INT2 + int "IRQ_USB_INT2" + default 10 +config IRQ_USB_DMA + int "IRQ_USB_DMA" + default 10 + + help + Enter the priority numbers between 7-13 ONLY. Others are Reserved. + This applies to all the above. It is not recommended to assign the + highest priority number 7 to UART or any other device. + +endmenu + +endmenu + +endif diff --git a/arch/blackfin/mach-bf527/Makefile b/arch/blackfin/mach-bf527/Makefile new file mode 100644 index 00000000000..9f99f5d0bcd --- /dev/null +++ b/arch/blackfin/mach-bf527/Makefile @@ -0,0 +1,9 @@ +# +# arch/blackfin/mach-bf527/Makefile +# + +extra-y := head.o + +obj-y := ints-priority.o dma.o + +obj-$(CONFIG_CPU_FREQ) += cpu.o diff --git a/arch/blackfin/mach-bf527/boards/Makefile b/arch/blackfin/mach-bf527/boards/Makefile new file mode 100644 index 00000000000..912ac8ebc88 --- /dev/null +++ b/arch/blackfin/mach-bf527/boards/Makefile @@ -0,0 +1,7 @@ +# +# arch/blackfin/mach-bf532/boards/Makefile +# + +obj-y += eth_mac.o +obj-$(CONFIG_BFIN527_EZKIT) += ezkit.o + diff --git a/arch/blackfin/mach-bf527/boards/eth_mac.c b/arch/blackfin/mach-bf527/boards/eth_mac.c new file mode 100644 index 00000000000..a725cc8a929 --- /dev/null +++ b/arch/blackfin/mach-bf527/boards/eth_mac.c @@ -0,0 +1,50 @@ +/* + * arch/blackfin/mach-bf537/board/eth_mac.c + * + * Copyright (C) 2007 Analog Devices, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include +#include + +#if defined(CONFIG_GENERIC_BOARD) || defined(CONFIG_BFIN537_STAMP) + +/* + * Currently the MAC address is saved in Flash by U-Boot + */ +#define FLASH_MAC 0x203f0000 + +void get_bf537_ether_addr(char *addr) +{ + unsigned int flash_mac = (unsigned int) FLASH_MAC; + *(u32 *)(&(addr[0])) = bfin_read32(flash_mac); + flash_mac += 4; + *(u16 *)(&(addr[4])) = bfin_read16(flash_mac); +} + +#else + +/* + * Provide MAC address function for other specific board setting + */ +void get_bf537_ether_addr(char *addr) +{ + printk(KERN_WARNING "%s: No valid Ethernet MAC address found\n", __FILE__); +} + +#endif + +EXPORT_SYMBOL(get_bf537_ether_addr); diff --git a/arch/blackfin/mach-bf527/boards/ezkit.c b/arch/blackfin/mach-bf527/boards/ezkit.c new file mode 100644 index 00000000000..09fb624af5a --- /dev/null +++ b/arch/blackfin/mach-bf527/boards/ezkit.c @@ -0,0 +1,737 @@ +/* + * File: arch/blackfin/mach-bf527/boards/ezkit.c + * Based on: arch/blackfin/mach-bf537/boards/stamp.c + * Author: Aidan Williams + * + * Created: + * Description: + * + * Modified: + * Copyright 2005 National ICT Australia (NICTA) + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +#include +#endif +#include +#include +#include +#include +#include +#include +#include +#include + +/* + * Name the Board for the /proc/cpuinfo + */ +char *bfin_board_name = "ADDS-BF527-EZKIT"; + +/* + * Driver needs to know address, irq and flag pin. + */ + +#define ISP1761_BASE 0x203C0000 +#define ISP1761_IRQ IRQ_PF7 + +#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE) +static struct resource bfin_isp1761_resources[] = { + [0] = { + .name = "isp1761-regs", + .start = ISP1761_BASE + 0x00000000, + .end = ISP1761_BASE + 0x000fffff, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = ISP1761_IRQ, + .end = ISP1761_IRQ, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_isp1761_device = { + .name = "isp1761", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_isp1761_resources), + .resource = bfin_isp1761_resources, +}; + +static struct platform_device *bfin_isp1761_devices[] = { + &bfin_isp1761_device, +}; + +int __init bfin_isp1761_init(void) +{ + unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices); + + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + set_irq_type(ISP1761_IRQ, IRQF_TRIGGER_FALLING); + + return platform_add_devices(bfin_isp1761_devices, num_devices); +} + +void __exit bfin_isp1761_exit(void) +{ + platform_device_unregister(&bfin_isp1761_device); +} + +arch_initcall(bfin_isp1761_init); +#endif + +#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) +static struct resource bfin_pcmcia_cf_resources[] = { + { + .start = 0x20310000, /* IO PORT */ + .end = 0x20312000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20311000, /* Attribute Memory */ + .end = 0x20311FFF, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF4, + .end = IRQ_PF4, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, + }, { + .start = 6, /* Card Detect PF6 */ + .end = 6, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pcmcia_cf_device = { + .name = "bfin_cf_pcmcia", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources), + .resource = bfin_pcmcia_cf_resources, +}; +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) +static struct platform_device rtc_device = { + .name = "rtc-bfin", + .id = -1, +}; +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) +static struct resource smc91x_resources[] = { + { + .name = "smc91x-regs", + .start = 0x20300300, + .end = 0x20300300 + 16, + .flags = IORESOURCE_MEM, + }, { + + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; +static struct platform_device smc91x_device = { + .name = "smc91x", + .id = 0, + .num_resources = ARRAY_SIZE(smc91x_resources), + .resource = smc91x_resources, +}; +#endif + +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) +static struct resource dm9000_resources[] = { + [0] = { + .start = 0x203FB800, + .end = 0x203FB800 + 8, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_PF9, + .end = IRQ_PF9, + .flags = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE), + }, +}; + +static struct platform_device dm9000_device = { + .name = "dm9000", + .id = -1, + .num_resources = ARRAY_SIZE(dm9000_resources), + .resource = dm9000_resources, +}; +#endif + +#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE) +static struct resource sl811_hcd_resources[] = { + { + .start = 0x20340000, + .end = 0x20340000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20340004, + .end = 0x20340004, + .flags = IORESOURCE_MEM, + }, { + .start = CONFIG_USB_SL811_BFIN_IRQ, + .end = CONFIG_USB_SL811_BFIN_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS) +void sl811_port_power(struct device *dev, int is_on) +{ + gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS"); + gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS); + + if (is_on) + gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 1); + else + gpio_set_value(CONFIG_USB_SL811_BFIN_GPIO_VBUS, 0); +} +#endif + +static struct sl811_platform_data sl811_priv = { + .potpg = 10, + .power = 250, /* == 500mA */ +#if defined(CONFIG_USB_SL811_BFIN_USE_VBUS) + .port_power = &sl811_port_power, +#endif +}; + +static struct platform_device sl811_hcd_device = { + .name = "sl811-hcd", + .id = 0, + .dev = { + .platform_data = &sl811_priv, + }, + .num_resources = ARRAY_SIZE(sl811_hcd_resources), + .resource = sl811_hcd_resources, +}; +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) +static struct resource isp1362_hcd_resources[] = { + { + .start = 0x20360000, + .end = 0x20360000, + .flags = IORESOURCE_MEM, + }, { + .start = 0x20360004, + .end = 0x20360004, + .flags = IORESOURCE_MEM, + }, { + .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ, + .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct isp1362_platform_data isp1362_priv = { + .sel15Kres = 1, + .clknotstop = 0, + .oc_enable = 0, + .int_act_high = 0, + .int_edge_triggered = 0, + .remote_wakeup_connected = 0, + .no_power_switching = 1, + .power_switching_mode = 0, +}; + +static struct platform_device isp1362_hcd_device = { + .name = "isp1362-hcd", + .id = 0, + .dev = { + .platform_data = &isp1362_priv, + }, + .num_resources = ARRAY_SIZE(isp1362_hcd_resources), + .resource = isp1362_hcd_resources, +}; +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) +static struct platform_device bfin_mac_device = { + .name = "bfin_mac", +}; +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) +static struct resource net2272_bfin_resources[] = { + { + .start = 0x20300000, + .end = 0x20300000 + 0x100, + .flags = IORESOURCE_MEM, + }, { + .start = IRQ_PF7, + .end = IRQ_PF7, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, + }, +}; + +static struct platform_device net2272_bfin_device = { + .name = "net2272", + .id = -1, + .num_resources = ARRAY_SIZE(net2272_bfin_resources), + .resource = net2272_bfin_resources, +}; +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) +/* all SPI peripherals info goes here */ + +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) +static struct mtd_partition bfin_spi_flash_partitions[] = { + { + .name = "bootloader", + .size = 0x00020000, + .offset = 0, + .mask_flags = MTD_CAP_ROM + }, { + .name = "kernel", + .size = 0xe0000, + .offset = 0x20000 + }, { + .name = "file system", + .size = 0x700000, + .offset = 0x00100000, + } +}; + +static struct flash_platform_data bfin_spi_flash_data = { + .name = "m25p80", + .parts = bfin_spi_flash_partitions, + .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), + .type = "m25p64", +}; + +/* SPI flash chip (m25p64) */ +static struct bfin5xx_spi_chip spi_flash_chip_info = { + .enable_dma = 0, /* use dma transfer with this chip*/ + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_SPI_ADC_BF533) \ + || defined(CONFIG_SPI_ADC_BF533_MODULE) +/* SPI ADC chip */ +static struct bfin5xx_spi_chip spi_adc_chip_info = { + .enable_dma = 1, /* use dma transfer with this chip*/ + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) \ + || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) +static struct bfin5xx_spi_chip ad1836_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE) +static struct bfin5xx_spi_chip ad9960_spi_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) +static struct bfin5xx_spi_chip spi_mmc_chip_info = { + .enable_dma = 1, + .bits_per_word = 8, +}; +#endif + +#if defined(CONFIG_PBX) +static struct bfin5xx_spi_chip spi_si3xxx_chip_info = { + .ctl_reg = 0x4, /* send zero */ + .enable_dma = 0, + .bits_per_word = 8, + .cs_change_per_word = 1, +}; +#endif + +#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE) +static struct bfin5xx_spi_chip ad5304_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; +#endif + +#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) +static struct bfin5xx_spi_chip spi_ad7877_chip_info = { + .enable_dma = 0, + .bits_per_word = 16, +}; + +static const struct ad7877_platform_data bfin_ad7877_ts_info = { + .model = 7877, + .vref_delay_usecs = 50, /* internal, no capacitor */ + .x_plate_ohms = 419, + .y_plate_ohms = 486, + .pressure_max = 1000, + .pressure_min = 0, + .stopacq_polarity = 1, + .first_conversion_delay = 3, + .acquisition_time = 1, + .averaging = 1, + .pen_down_acc_interval = 1, +}; +#endif + +static struct spi_board_info bfin_spi_board_info[] __initdata = { +#if defined(CONFIG_MTD_M25P80) \ + || defined(CONFIG_MTD_M25P80_MODULE) + { + /* the modalias must be the same as spi device driver name */ + .modalias = "m25p80", /* Name of spi_driver for this device */ + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ + .platform_data = &bfin_spi_flash_data, + .controller_data = &spi_flash_chip_info, + .mode = SPI_MODE_3, + }, +#endif + +#if defined(CONFIG_SPI_ADC_BF533) \ + || defined(CONFIG_SPI_ADC_BF533_MODULE) + { + .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ + .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, /* Framework bus number */ + .chip_select = 1, /* Framework chip select. */ + .platform_data = NULL, /* No spi_driver specific config */ + .controller_data = &spi_adc_chip_info, + }, +#endif + +#if defined(CONFIG_SND_BLACKFIN_AD1836) \ + || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) + { + .modalias = "ad1836-spi", + .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, + .controller_data = &ad1836_spi_chip_info, + }, +#endif +#if defined(CONFIG_AD9960) || defined(CONFIG_AD9960_MODULE) + { + .modalias = "ad9960-spi", + .max_speed_hz = 10000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 1, + .controller_data = &ad9960_spi_chip_info, + }, +#endif +#if defined(CONFIG_SPI_MMC) || defined(CONFIG_SPI_MMC_MODULE) + { + .modalias = "spi_mmc_dummy", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 0, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "spi_mmc", + .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = CONFIG_SPI_MMC_CS_CHAN, + .platform_data = NULL, + .controller_data = &spi_mmc_chip_info, + .mode = SPI_MODE_3, + }, +#endif +#if defined(CONFIG_PBX) + { + .modalias = "fxs-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 8 - CONFIG_J11_JUMPER, + .controller_data = &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, + { + .modalias = "fxo-spi", + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 8 - CONFIG_J19_JUMPER, + .controller_data = &spi_si3xxx_chip_info, + .mode = SPI_MODE_3, + }, +#endif +#if defined(CONFIG_AD5304) || defined(CONFIG_AD5304_MODULE) + { + .modalias = "ad5304_spi", + .max_speed_hz = 1250000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 0, + .chip_select = 2, + .platform_data = NULL, + .controller_data = &ad5304_chip_info, + .mode = SPI_MODE_2, + }, +#endif +#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) + { + .modalias = "ad7877", + .platform_data = &bfin_ad7877_ts_info, + .irq = IRQ_PF6, + .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ + .bus_num = 1, + .chip_select = 1, + .controller_data = &spi_ad7877_chip_info, + }, +#endif +}; + +/* SPI controller data */ +static struct bfin5xx_spi_master bfin_spi0_info = { + .num_chipselect = 8, + .enable_dma = 1, /* master has the ability to do dma transfer */ +}; + +/* SPI (0) */ +static struct resource bfin_spi0_resource[] = { + [0] = { + .start = SPI0_REGBASE, + .end = SPI0_REGBASE + 0xFF, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = CH_SPI, + .end = CH_SPI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_spi0_device = { + .name = "bfin-spi", + .id = 0, /* Bus number */ + .num_resources = ARRAY_SIZE(bfin_spi0_resource), + .resource = bfin_spi0_resource, + .dev = { + .platform_data = &bfin_spi0_info, /* Passed to driver */ + }, +}; +#endif /* spi master and devices */ + +#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) +static struct platform_device bfin_fb_device = { + .name = "bf537-lq035", +}; +#endif + +#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE) +static struct platform_device bfin_fb_adv7393_device = { + .name = "bfin-adv7393", +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) +static struct resource bfin_uart_resources[] = { +#ifdef CONFIG_SERIAL_BFIN_UART0 + { + .start = 0xFFC00400, + .end = 0xFFC004FF, + .flags = IORESOURCE_MEM, + }, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + { + .start = 0xFFC02000, + .end = 0xFFC020FF, + .flags = IORESOURCE_MEM, + }, +#endif +}; + +static struct platform_device bfin_uart_device = { + .name = "bfin-uart", + .id = 1, + .num_resources = ARRAY_SIZE(bfin_uart_resources), + .resource = bfin_uart_resources, +}; +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) +static struct resource bfin_twi0_resource[] = { + [0] = { + .start = TWI0_REGBASE, + .end = TWI0_REGBASE, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = IRQ_TWI, + .end = IRQ_TWI, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device i2c_bfin_twi_device = { + .name = "i2c-bfin-twi", + .id = 0, + .num_resources = ARRAY_SIZE(bfin_twi0_resource), + .resource = bfin_twi0_resource, +}; +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) +static struct platform_device bfin_sport0_uart_device = { + .name = "bfin-sport-uart", + .id = 0, +}; + +static struct platform_device bfin_sport1_uart_device = { + .name = "bfin-sport-uart", + .id = 1, +}; +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) +#define PATA_INT 55 + +static struct pata_platform_info bfin_pata_platform_data = { + .ioport_shift = 1, + .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED, +}; + +static struct resource bfin_pata_resources[] = { + { + .start = 0x20314020, + .end = 0x2031403F, + .flags = IORESOURCE_MEM, + }, + { + .start = 0x2031401C, + .end = 0x2031401F, + .flags = IORESOURCE_MEM, + }, + { + .start = PATA_INT, + .end = PATA_INT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device bfin_pata_device = { + .name = "pata_platform", + .id = -1, + .num_resources = ARRAY_SIZE(bfin_pata_resources), + .resource = bfin_pata_resources, + .dev = { + .platform_data = &bfin_pata_platform_data, + } +}; +#endif + +static struct platform_device *stamp_devices[] __initdata = { +#if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) + &bfin_pcmcia_cf_device, +#endif + +#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) + &rtc_device, +#endif + +#if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE) + &sl811_hcd_device, +#endif + +#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) + &isp1362_hcd_device, +#endif + +#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) + &smc91x_device, +#endif + +#if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE) + &dm9000_device, +#endif + +#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) + &bfin_mac_device, +#endif + +#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) + &net2272_bfin_device, +#endif + +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + &bfin_spi0_device, +#endif + +#if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) + &bfin_fb_device, +#endif + +#if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE) + &bfin_fb_adv7393_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) + &bfin_uart_device, +#endif + +#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE) + &i2c_bfin_twi_device, +#endif + +#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE) + &bfin_sport0_uart_device, + &bfin_sport1_uart_device, +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + &bfin_pata_device, +#endif +}; + +static int __init stamp_init(void) +{ + printk(KERN_INFO "%s(): registering device resources\n", __FUNCTION__); + platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); +#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) + spi_register_board_info(bfin_spi_board_info, + ARRAY_SIZE(bfin_spi_board_info)); +#endif + +#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE) + irq_desc[PATA_INT].status |= IRQ_NOAUTOEN; +#endif + return 0; +} + +arch_initcall(stamp_init); + +void native_machine_restart(char *cmd) +{ + /* workaround reboot hang when booting from SPI */ + if ((bfin_read_SYSCR() & 0x7) == 0x3) + bfin_gpio_reset_spi0_ssel1(); +} diff --git a/arch/blackfin/mach-bf527/cpu.c b/arch/blackfin/mach-bf527/cpu.c new file mode 100644 index 00000000000..1975402b1db --- /dev/null +++ b/arch/blackfin/mach-bf527/cpu.c @@ -0,0 +1,161 @@ +/* + * File: arch/blackfin/mach-bf527/cpu.c + * Based on: arch/blackfin/mach-bf537/cpu.c + * Author: michael.kang@analog.com + * + * Created: + * Description: clock scaling for the bf527 + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include +#include +#include +#include + +/* CONFIG_CLKIN_HZ=11059200 */ +#define VCO5 (CONFIG_CLKIN_HZ*45) /*497664000 */ +#define VCO4 (CONFIG_CLKIN_HZ*36) /*398131200 */ +#define VCO3 (CONFIG_CLKIN_HZ*27) /*298598400 */ +#define VCO2 (CONFIG_CLKIN_HZ*18) /*199065600 */ +#define VCO1 (CONFIG_CLKIN_HZ*9) /*99532800 */ +#define VCO(x) VCO##x + +#define MFREQ(x) {VCO(x), VCO(x)/4}, {VCO(x), VCO(x)/2}, {VCO(x), VCO(x)} +/* frequency */ +static struct cpufreq_frequency_table bf527_freq_table[] = { + MFREQ(1), + MFREQ(3), + {VCO4, VCO4 / 2}, {VCO4, VCO4}, + MFREQ(5), + {0, CPUFREQ_TABLE_END}, +}; + +/* + * dpmc_fops->ioctl() + * static int dpmc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, unsigned long arg) + */ +static int bf527_getfreq(unsigned int cpu) +{ + unsigned long cclk_mhz; + + /* The driver only support single cpu */ + if (cpu == 0) + dpmc_fops.ioctl(NULL, NULL, IOCTL_GET_CORECLOCK, &cclk_mhz); + else + cclk_mhz = -1; + + return cclk_mhz; +} + +static int bf527_target(struct cpufreq_policy *policy, + unsigned int target_freq, unsigned int relation) +{ + unsigned long cclk_mhz; + unsigned long vco_mhz; + unsigned long flags; + unsigned int index; + struct cpufreq_freqs freqs; + + if (cpufreq_frequency_table_target + (policy, bf527_freq_table, target_freq, relation, &index)) + return -EINVAL; + + cclk_mhz = bf527_freq_table[index].frequency; + vco_mhz = bf527_freq_table[index].index; + + dpmc_fops.ioctl(NULL, NULL, IOCTL_CHANGE_FREQUENCY, &vco_mhz); + freqs.old = bf527_getfreq(0); + freqs.new = cclk_mhz; + freqs.cpu = 0; + + pr_debug + ("cclk begin change to cclk %d,vco=%d,index=%d,target=%d,oldfreq=%d\n", + cclk_mhz, vco_mhz, index, target_freq, freqs.old); + + cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); + local_irq_save(flags); + dpmc_fops.ioctl(NULL, NULL, IOCTL_SET_CCLK, &cclk_mhz); + local_irq_restore(flags); + cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); + + vco_mhz = get_vco(); + cclk_mhz = get_cclk(); + return 0; +} + +/* make sure that only the "userspace" governor is run -- anything else wouldn't make sense on + * this platform, anyway. + */ +static int bf527_verify_speed(struct cpufreq_policy *policy) +{ + return cpufreq_frequency_table_verify(policy, &bf527_freq_table); +} + +static int __init __bf527_cpu_init(struct cpufreq_policy *policy) +{ + if (policy->cpu != 0) + return -EINVAL; + + policy->governor = CPUFREQ_DEFAULT_GOVERNOR; + + policy->cpuinfo.transition_latency = CPUFREQ_ETERNAL; + /*Now ,only support one cpu */ + policy->cur = bf527_getfreq(0); + cpufreq_frequency_table_get_attr(bf527_freq_table, policy->cpu); + return cpufreq_frequency_table_cpuinfo(policy, bf527_freq_table); +} + +static struct freq_attr *bf527_freq_attr[] = { + &cpufreq_freq_attr_scaling_available_freqs, + NULL, +}; + +static struct cpufreq_driver bf527_driver = { + .verify = bf527_verify_speed, + .target = bf527_target, + .get = bf527_getfreq, + .init = __bf527_cpu_init, + .name = "bf527", + .owner = THIS_MODULE, + .attr = bf527_freq_attr, +}; + +static int __init bf527_cpu_init(void) +{ + return cpufreq_register_driver(&bf527_driver); +} + +static void __exit bf527_cpu_exit(void) +{ + cpufreq_unregister_driver(&bf527_driver); +} + +MODULE_AUTHOR("Mickael Kang"); +MODULE_DESCRIPTION("cpufreq driver for bf527 CPU"); +MODULE_LICENSE("GPL"); + +module_init(bf527_cpu_init); +module_exit(bf527_cpu_exit); diff --git a/arch/blackfin/mach-bf527/dma.c b/arch/blackfin/mach-bf527/dma.c new file mode 100644 index 00000000000..522de24cc39 --- /dev/null +++ b/arch/blackfin/mach-bf527/dma.c @@ -0,0 +1,115 @@ +/* + * File: arch/blackfin/mach-bf527/dma.c + * Based on: + * Author: + * + * Created: + * Description: This file contains the simple DMA Implementation for Blackfin + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ +#include +#include + +struct dma_register *base_addr[MAX_BLACKFIN_DMA_CHANNEL] = { + (struct dma_register *) DMA0_NEXT_DESC_PTR, + (struct dma_register *) DMA1_NEXT_DESC_PTR, + (struct dma_register *) DMA2_NEXT_DESC_PTR, + (struct dma_register *) DMA3_NEXT_DESC_PTR, + (struct dma_register *) DMA4_NEXT_DESC_PTR, + (struct dma_register *) DMA5_NEXT_DESC_PTR, + (struct dma_register *) DMA6_NEXT_DESC_PTR, + (struct dma_register *) DMA7_NEXT_DESC_PTR, + (struct dma_register *) DMA8_NEXT_DESC_PTR, + (struct dma_register *) DMA9_NEXT_DESC_PTR, + (struct dma_register *) DMA10_NEXT_DESC_PTR, + (struct dma_register *) DMA11_NEXT_DESC_PTR, + (struct dma_register *) MDMA_D0_NEXT_DESC_PTR, + (struct dma_register *) MDMA_S0_NEXT_DESC_PTR, + (struct dma_register *) MDMA_D1_NEXT_DESC_PTR, + (struct dma_register *) MDMA_S1_NEXT_DESC_PTR, +}; + +int channel2irq(unsigned int channel) +{ + int ret_irq = -1; + + switch (channel) { + case CH_PPI: + ret_irq = IRQ_PPI; + break; + + case CH_EMAC_RX: + ret_irq = IRQ_MAC_RX; + break; + + case CH_EMAC_TX: + ret_irq = IRQ_MAC_TX; + break; + + case CH_UART1_RX: + ret_irq = IRQ_UART1_RX; + break; + + case CH_UART1_TX: + ret_irq = IRQ_UART1_TX; + break; + + case CH_SPORT0_RX: + ret_irq = IRQ_SPORT0_RX; + break; + + case CH_SPORT0_TX: + ret_irq = IRQ_SPORT0_TX; + break; + + case CH_SPORT1_RX: + ret_irq = IRQ_SPORT1_RX; + break; + + case CH_SPORT1_TX: + ret_irq = IRQ_SPORT1_TX; + break; + + case CH_SPI: + ret_irq = IRQ_SPI; + break; + + case CH_UART0_RX: + ret_irq = IRQ_UART0_RX; + break; + + case CH_UART0_TX: + ret_irq = IRQ_UART0_TX; + break; + + case CH_MEM_STREAM0_SRC: + case CH_MEM_STREAM0_DEST: + ret_irq = IRQ_MEM_DMA0; + break; + + case CH_MEM_STREAM1_SRC: + case CH_MEM_STREAM1_DEST: + ret_irq = IRQ_MEM_DMA1; + break; + } + return ret_irq; +} diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S new file mode 100644 index 00000000000..cdb00a08496 --- /dev/null +++ b/arch/blackfin/mach-bf527/head.S @@ -0,0 +1,456 @@ +/* + * File: arch/blackfin/mach-bf527/head.S + * Based on: arch/blackfin/mach-bf533/head.S + * Author: Jeff Dionne COPYRIGHT 1998 D. Jeff Dionne + * + * Created: 1998 + * Description: Startup code for Blackfin BF537 + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include +#include + +#if CONFIG_BFIN_KERNEL_CLOCK +#include +#include +#endif + +.global __rambase +.global __ramstart +.global __ramend +.extern ___bss_stop +.extern ___bss_start +.extern _bf53x_relocate_l1_mem + +#define INITIAL_STACK 0xFFB01000 + +__INIT + +ENTRY(__start) + /* R0: argument of command line string, passed from uboot, save it */ + R7 = R0; + /* Enable Cycle Counter and Nesting Of Interrupts */ +#ifdef CONFIG_BFIN_SCRATCH_REG_CYCLES + R0 = SYSCFG_SNEN; +#else + R0 = SYSCFG_SNEN | SYSCFG_CCEN; +#endif + SYSCFG = R0; + R0 = 0; + + /* Clear Out All the data and pointer Registers */ + R1 = R0; + R2 = R0; + R3 = R0; + R4 = R0; + R5 = R0; + R6 = R0; + + P0 = R0; + P1 = R0; + P2 = R0; + P3 = R0; + P4 = R0; + P5 = R0; + + LC0 = r0; + LC1 = r0; + L0 = r0; + L1 = r0; + L2 = r0; + L3 = r0; + + /* Clear Out All the DAG Registers */ + B0 = r0; + B1 = r0; + B2 = r0; + B3 = r0; + + I0 = r0; + I1 = r0; + I2 = r0; + I3 = r0; + + M0 = r0; + M1 = r0; + M2 = r0; + M3 = r0; + + trace_buffer_init(p0,r0); + P0 = R1; + R0 = R1; + + /* Turn off the icache */ + p0.l = LO(IMEM_CONTROL); + p0.h = HI(IMEM_CONTROL); + R1 = [p0]; + R0 = ~ENICPLB; + R0 = R0 & R1; + + /* Anomaly 05000125 */ +#if ANOMALY_05000125 + CLI R2; + SSYNC; +#endif + [p0] = R0; + SSYNC; +#if ANOMALY_05000125 + STI R2; +#endif + + /* Turn off the dcache */ + p0.l = LO(DMEM_CONTROL); + p0.h = HI(DMEM_CONTROL); + R1 = [p0]; + R0 = ~ENDCPLB; + R0 = R0 & R1; + + /* Anomaly 05000125 */ +#if ANOMALY_05000125 + CLI R2; + SSYNC; +#endif + [p0] = R0; + SSYNC; +#if ANOMALY_05000125 + STI R2; +#endif + + +#if defined(CONFIG_BF527) + p0.h = hi(EMAC_SYSTAT); + p0.l = lo(EMAC_SYSTAT); + R0.h = 0xFFFF; /* Clear EMAC Interrupt Status bits */ + R0.l = 0xFFFF; + [P0] = R0; + SSYNC; +#endif + + /* Initialise UART - when booting from u-boot, the UART is not disabled + * so if we dont initalize here, our serial console gets hosed */ + p0.h = hi(UART1_LCR); + p0.l = lo(UART1_LCR); + r0 = 0x0(Z); + w[p0] = r0.L; /* To enable DLL writes */ + ssync; + + p0.h = hi(UART1_DLL); + p0.l = lo(UART1_DLL); + r0 = 0x0(Z); + w[p0] = r0.L; + ssync; + + p0.h = hi(UART1_DLH); + p0.l = lo(UART1_DLH); + r0 = 0x00(Z); + w[p0] = r0.L; + ssync; + + p0.h = hi(UART1_GCTL); + p0.l = lo(UART1_GCTL); + r0 = 0x0(Z); + w[p0] = r0.L; /* To enable UART clock */ + ssync; + + /* Initialize stack pointer */ + sp.l = lo(INITIAL_STACK); + sp.h = hi(INITIAL_STACK); + fp = sp; + usp = sp; + +#ifdef CONFIG_EARLY_PRINTK + SP += -12; + call _init_early_exception_vectors; + SP += 12; +#endif + + /* Put The Code for PLL Programming and SDRAM Programming in L1 ISRAM */ + call _bf53x_relocate_l1_mem; +#if CONFIG_BFIN_KERNEL_CLOCK + call _start_dma_code; +#endif + + /* Code for initializing Async memory banks */ + + p2.h = hi(EBIU_AMBCTL1); + p2.l = lo(EBIU_AMBCTL1); + r0.h = hi(AMBCTL1VAL); + r0.l = lo(AMBCTL1VAL); + [p2] = r0; + ssync; + + p2.h = hi(EBIU_AMBCTL0); + p2.l = lo(EBIU_AMBCTL0); + r0.h = hi(AMBCTL0VAL); + r0.l = lo(AMBCTL0VAL); + [p2] = r0; + ssync; + + p2.h = hi(EBIU_AMGCTL); + p2.l = lo(EBIU_AMGCTL); + r0 = AMGCTLVAL; + w[p2] = r0; + ssync; + + /* This section keeps the processor in supervisor mode + * during kernel boot. Switches to user mode at end of boot. + * See page 3-9 of Hardware Reference manual for documentation. + */ + + /* EVT15 = _real_start */ + + p0.l = lo(EVT15); + p0.h = hi(EVT15); + p1.l = _real_start; + p1.h = _real_start; + [p0] = p1; + csync; + + p0.l = lo(IMASK); + p0.h = hi(IMASK); + p1.l = IMASK_IVG15; + p1.h = 0x0; + [p0] = p1; + csync; + + raise 15; + p0.l = .LWAIT_HERE; + p0.h = .LWAIT_HERE; + reti = p0; +#if ANOMALY_05000281 + nop; nop; nop; +#endif + rti; + +.LWAIT_HERE: + jump .LWAIT_HERE; +ENDPROC(__start) + +ENTRY(_real_start) + [ -- sp ] = reti; + p0.l = lo(WDOG_CTL); + p0.h = hi(WDOG_CTL); + r0 = 0xAD6(z); + w[p0] = r0; /* watchdog off for now */ + ssync; + + /* Code update for BSS size == 0 + * Zero out the bss region. + */ + + p1.l = ___bss_start; + p1.h = ___bss_start; + p2.l = ___bss_stop; + p2.h = ___bss_stop; + r0 = 0; + p2 -= p1; + lsetup (.L_clear_bss, .L_clear_bss) lc0 = p2; +.L_clear_bss: + B[p1++] = r0; + + /* In case there is a NULL pointer reference + * Zero out region before stext + */ + + p1.l = 0x0; + p1.h = 0x0; + r0.l = __stext; + r0.h = __stext; + r0 = r0 >> 1; + p2 = r0; + r0 = 0; + lsetup (.L_clear_zero, .L_clear_zero) lc0 = p2; +.L_clear_zero: + W[p1++] = r0; + + /* pass the uboot arguments to the global value command line */ + R0 = R7; + call _cmdline_init; + + p1.l = __rambase; + p1.h = __rambase; + r0.l = __sdata; + r0.h = __sdata; + [p1] = r0; + + p1.l = __ramstart; + p1.h = __ramstart; + p3.l = ___bss_stop; + p3.h = ___bss_stop; + + r1 = p3; + [p1] = r1; + + /* + * load the current thread pointer and stack + */ + r1.l = _init_thread_union; + r1.h = _init_thread_union; + + r2.l = 0x2000; + r2.h = 0x0000; + r1 = r1 + r2; + sp = r1; + usp = sp; + fp = sp; + jump.l _start_kernel; +ENDPROC(_real_start) + +__FINIT + +.section .l1.text +#if CONFIG_BFIN_KERNEL_CLOCK +ENTRY(_start_dma_code) + + /* Enable PHY CLK buffer output */ + p0.h = hi(VR_CTL); + p0.l = lo(VR_CTL); + r0.l = w[p0]; + bitset(r0, 14); + w[p0] = r0.l; + ssync; + + p0.h = hi(SIC_IWR0); + p0.l = lo(SIC_IWR0); + r0.l = 0x1; + r0.h = 0x0; + [p0] = r0; + SSYNC; + + /* + * Set PLL_CTL + * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors + * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK + * - [7] = output delay (add 200ps of delay to mem signals) + * - [6] = input delay (add 200ps of input delay to mem signals) + * - [5] = PDWN : 1=All Clocks off + * - [3] = STOPCK : 1=Core Clock off + * - [1] = PLL_OFF : 1=Disable Power to PLL + * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL + * all other bits set to zero + */ + + p0.h = hi(PLL_LOCKCNT); + p0.l = lo(PLL_LOCKCNT); + r0 = 0x300(Z); + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITSET (R0, 24); + [P2] = R0; + SSYNC; + + r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */ + r0 = r0 << 9; /* Shift it over, */ + r1 = CLKIN_HALF; /* Do we need to divide CLKIN by 2?*/ + r0 = r1 | r0; + r1 = PLL_BYPASS; /* Bypass the PLL? */ + r1 = r1 << 8; /* Shift it over */ + r0 = r1 | r0; /* add them all together */ + + p0.h = hi(PLL_CTL); + p0.l = lo(PLL_CTL); /* Load the address */ + cli r2; /* Disable interrupts */ + ssync; + w[p0] = r0.l; /* Set the value */ + idle; /* Wait for the PLL to stablize */ + sti r2; /* Enable interrupts */ + +.Lcheck_again: + p0.h = hi(PLL_STAT); + p0.l = lo(PLL_STAT); + R0 = W[P0](Z); + CC = BITTST(R0,5); + if ! CC jump .Lcheck_again; + + /* Configure SCLK & CCLK Dividers */ + r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV); + p0.h = hi(PLL_DIV); + p0.l = lo(PLL_DIV); + w[p0] = r0.l; + ssync; + + p0.l = lo(EBIU_SDRRC); + p0.h = hi(EBIU_SDRRC); + r0 = mem_SDRRC; + w[p0] = r0.l; + ssync; + + p0.l = LO(EBIU_SDBCTL); + p0.h = HI(EBIU_SDBCTL); /* SDRAM Memory Bank Control Register */ + r0 = mem_SDBCTL; + w[p0] = r0.l; + ssync; + + P2.H = hi(EBIU_SDGCTL); + P2.L = lo(EBIU_SDGCTL); + R0 = [P2]; + BITCLR (R0, 24); + p0.h = hi(EBIU_SDSTAT); + p0.l = lo(EBIU_SDSTAT); + r2.l = w[p0]; + cc = bittst(r2,3); + if !cc jump .Lskip; + NOP; + BITSET (R0, 23); +.Lskip: + [P2] = R0; + SSYNC; + + R0.L = lo(mem_SDGCTL); + R0.H = hi(mem_SDGCTL); + R1 = [p2]; + R1 = R1 | R0; + [P2] = R1; + SSYNC; + + p0.h = hi(SIC_IWR0); + p0.l = lo(SIC_IWR0); + r0.l = lo(IWR_ENABLE_ALL); + r0.h = hi(IWR_ENABLE_ALL); + [p0] = r0; + SSYNC; + + RTS; +ENDPROC(_start_dma_code) +#endif /* CONFIG_BFIN_KERNEL_CLOCK */ + +.data + +/* + * Set up the usable of RAM stuff. Size of RAM is determined then + * an initial stack set up at the end. + */ + +.align 4 +__rambase: +.long 0 +__ramstart: +.long 0 +__ramend: +.long 0 diff --git a/arch/blackfin/mach-bf527/ints-priority.c b/arch/blackfin/mach-bf527/ints-priority.c new file mode 100644 index 00000000000..1fa38979396 --- /dev/null +++ b/arch/blackfin/mach-bf527/ints-priority.c @@ -0,0 +1,100 @@ +/* + * File: arch/blackfin/mach-bf537/ints-priority.c + * Based on: arch/blackfin/mach-bf533/ints-priority.c + * Author: Michael Hennerich (michael.hennerich@analog.com) + * + * Created: + * Description: Set up the interrupt priorities + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#include +#include +#include + +void program_IAR(void) +{ + /* Program the IAR0 Register with the configured priority */ + bfin_write_SIC_IAR0(((CONFIG_IRQ_PLL_WAKEUP - 7) << IRQ_PLL_WAKEUP_POS) | + ((CONFIG_IRQ_DMA0_ERROR - 7) << IRQ_DMA0_ERROR_POS) | + ((CONFIG_IRQ_DMAR0_BLK - 7) << IRQ_DMAR0_BLK_POS) | + ((CONFIG_IRQ_DMAR1_BLK - 7) << IRQ_DMAR1_BLK_POS) | + ((CONFIG_IRQ_DMAR0_OVR - 7) << IRQ_DMAR0_OVR_POS) | + ((CONFIG_IRQ_DMAR1_OVR - 7) << IRQ_DMAR1_OVR_POS) | + ((CONFIG_IRQ_PPI_ERROR - 7) << IRQ_PPI_ERROR_POS) | + ((CONFIG_IRQ_MAC_ERROR - 7) << IRQ_MAC_ERROR_POS)); + + + bfin_write_SIC_IAR1(((CONFIG_IRQ_SPORT0_ERROR - 7) << IRQ_SPORT0_ERROR_POS) | + ((CONFIG_IRQ_SPORT1_ERROR - 7) << IRQ_SPORT1_ERROR_POS) | + ((CONFIG_IRQ_UART0_ERROR - 7) << IRQ_UART0_ERROR_POS) | + ((CONFIG_IRQ_UART1_ERROR - 7) << IRQ_UART1_ERROR_POS) | + ((CONFIG_IRQ_RTC - 7) << IRQ_RTC_POS) | + ((CONFIG_IRQ_PPI - 7) << IRQ_PPI_POS)); + + bfin_write_SIC_IAR2(((CONFIG_IRQ_SPORT0_RX - 7) << IRQ_SPORT0_RX_POS) | + ((CONFIG_IRQ_SPORT0_TX - 7) << IRQ_SPORT0_TX_POS) | + ((CONFIG_IRQ_SPORT1_RX - 7) << IRQ_SPORT1_RX_POS) | + ((CONFIG_IRQ_SPORT1_TX - 7) << IRQ_SPORT1_TX_POS) | + ((CONFIG_IRQ_TWI - 7) << IRQ_TWI_POS) | + ((CONFIG_IRQ_SPI - 7) << IRQ_SPI_POS) | + ((CONFIG_IRQ_UART0_RX - 7) << IRQ_UART0_RX_POS) | + ((CONFIG_IRQ_UART0_TX - 7) << IRQ_UART0_TX_POS)); + + bfin_write_SIC_IAR3(((CONFIG_IRQ_UART1_RX - 7) << IRQ_UART1_RX_POS) | + ((CONFIG_IRQ_UART1_TX - 7) << IRQ_UART1_TX_POS) | + ((CONFIG_IRQ_OPTSEC - 7) << IRQ_OPTSEC_POS) | + ((CONFIG_IRQ_CNT - 7) << IRQ_CNT_POS) | + ((CONFIG_IRQ_MAC_RX - 7) << IRQ_MAC_RX_POS) | + ((CONFIG_IRQ_PORTH_INTA - 7) << IRQ_PORTH_INTA_POS) | + ((CONFIG_IRQ_MAC_TX - 7) << IRQ_MAC_TX_POS) | + ((CONFIG_IRQ_PORTH_INTB - 7) << IRQ_PORTH_INTB_POS)); + + bfin_write_SIC_IAR4(((CONFIG_IRQ_TMR0 - 7) << IRQ_TMR0_POS) | + ((CONFIG_IRQ_TMR1 - 7) << IRQ_TMR1_POS) | + ((CONFIG_IRQ_TMR2 - 7) << IRQ_TMR2_POS) | + ((CONFIG_IRQ_TMR3 - 7) << IRQ_TMR3_POS) | + ((CONFIG_IRQ_TMR4 - 7) << IRQ_TMR4_POS) | + ((CONFIG_IRQ_TMR5 - 7) << IRQ_TMR5_POS) | + ((CONFIG_IRQ_TMR6 - 7) << IRQ_TMR6_POS) | + ((CONFIG_IRQ_TMR7 - 7) << IRQ_TMR7_POS)); + + bfin_write_SIC_IAR5(((CONFIG_IRQ_PORTG_INTA - 7) << IRQ_PORTG_INTA_POS) | + ((CONFIG_IRQ_PORTG_INTB - 7) << IRQ_PORTG_INTB_POS) | + ((CONFIG_IRQ_MEM_DMA0 - 7) << IRQ_MEM_DMA0_POS) | + ((CONFIG_IRQ_MEM_DMA1 - 7) << IRQ_MEM_DMA1_POS) | + ((CONFIG_IRQ_WATCH - 7) << IRQ_WATCH_POS) | + ((CONFIG_IRQ_PORTF_INTA - 7) << IRQ_PORTF_INTA_POS) | + ((CONFIG_IRQ_PORTF_INTB - 7) << IRQ_PORTF_INTB_POS) | + ((CONFIG_IRQ_SPI_ERROR - 7) << IRQ_SPI_ERROR_POS)); + + bfin_write_SIC_IAR6(((CONFIG_IRQ_NFC_ERROR - 7) << IRQ_NFC_ERROR_POS) | + ((CONFIG_IRQ_HDMA_ERROR - 7) << IRQ_HDMA_ERROR_POS) | + ((CONFIG_IRQ_HDMA - 7) << IRQ_HDMA_POS) | + ((CONFIG_IRQ_USB_EINT - 7) << IRQ_USB_EINT_POS) | + ((CONFIG_IRQ_USB_INT0 - 7) << IRQ_USB_INT0_POS) | + ((CONFIG_IRQ_USB_INT1 - 7) << IRQ_USB_INT1_POS) | + ((CONFIG_IRQ_USB_INT2 - 7) << IRQ_USB_INT2_POS) | + ((CONFIG_IRQ_USB_DMA - 7) << IRQ_USB_DMA_POS)); + + SSYNC(); +} diff --git a/arch/blackfin/mach-common/ints-priority-sc.c b/arch/blackfin/mach-common/ints-priority-sc.c index d3b7672b2b9..e06fe96b6fc 100644 --- a/arch/blackfin/mach-common/ints-priority-sc.c +++ b/arch/blackfin/mach-common/ints-priority-sc.c @@ -92,10 +92,15 @@ static void __init search_IAR(void) for (irqn = 0; irqn < NR_PERI_INTS; irqn++) { int iar_shift = (irqn & 7) * 4; - if (ivg == + if (ivg == (0xf & +#ifndef CONFIG_BF52x bfin_read32((unsigned long *)SIC_IAR0 + (irqn >> 3)) >> iar_shift)) { +#else + bfin_read32((unsigned long *)SIC_IAR0 + + ((irqn%32) >> 3) + ((irqn / 32) * 16)) >> iar_shift)) { +#endif ivg_table[irq_pos].irqno = IVG7 + irqn; ivg_table[irq_pos].isrflag = 1 << (irqn % 32); ivg7_13[ivg].istop++; @@ -140,7 +145,7 @@ static void bfin_core_unmask_irq(unsigned int irq) static void bfin_internal_mask_irq(unsigned int irq) { -#ifndef CONFIG_BF54x +#ifdef CONFIG_BF53x bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() & ~(1 << (irq - (IRQ_CORETMR + 1)))); #else @@ -155,7 +160,7 @@ static void bfin_internal_mask_irq(unsigned int irq) static void bfin_internal_unmask_irq(unsigned int irq) { -#ifndef CONFIG_BF54x +#ifdef CONFIG_BF53x bfin_write_SIC_IMASK(bfin_read_SIC_IMASK() | (1 << (irq - (IRQ_CORETMR + 1)))); #else @@ -750,13 +755,15 @@ int __init init_arch_irq(void) int irq; unsigned long ilat = 0; /* Disable all the peripheral intrs - page 4-29 HW Ref manual */ -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) bfin_write_SIC_IMASK0(SIC_UNMASK_ALL); bfin_write_SIC_IMASK1(SIC_UNMASK_ALL); - bfin_write_SIC_IMASK2(SIC_UNMASK_ALL); bfin_write_SIC_IWR0(IWR_ENABLE_ALL); bfin_write_SIC_IWR1(IWR_ENABLE_ALL); +#ifdef CONFIG_BF54x + bfin_write_SIC_IMASK2(SIC_UNMASK_ALL); bfin_write_SIC_IWR2(IWR_ENABLE_ALL); +#endif #else bfin_write_SIC_IMASK(SIC_UNMASK_ALL); bfin_write_SIC_IWR(IWR_ENABLE_ALL); @@ -787,7 +794,7 @@ int __init init_arch_irq(void) switch (irq) { #ifdef CONFIG_IRQCHIP_DEMUX_GPIO -#ifndef CONFIG_BF54x +#if defined(CONFIG_BF53x) case IRQ_PROG_INTA: set_irq_chained_handler(irq, bfin_demux_gpio_irq); @@ -798,7 +805,7 @@ int __init init_arch_irq(void) bfin_demux_gpio_irq); break; #endif -#else +#elif defined(CONFIG_BF54x) case IRQ_PINT0: set_irq_chained_handler(irq, bfin_demux_gpio_irq); @@ -815,7 +822,20 @@ int __init init_arch_irq(void) set_irq_chained_handler(irq, bfin_demux_gpio_irq); break; -#endif /*CONFIG_BF54x */ +#elif defined(CONFIG_BF52x) + case IRQ_PORTF_INTA: + set_irq_chained_handler(irq, + bfin_demux_gpio_irq); + break; + case IRQ_PORTG_INTA: + set_irq_chained_handler(irq, + bfin_demux_gpio_irq); + break; + case IRQ_PORTH_INTA: + set_irq_chained_handler(irq, + bfin_demux_gpio_irq); + break; +#endif #endif default: set_irq_handler(irq, handle_simple_irq); @@ -880,14 +900,15 @@ void do_irq(int vec, struct pt_regs *fp) } else { struct ivgx *ivg = ivg7_13[vec - IVG7].ifirst; struct ivgx *ivg_stop = ivg7_13[vec - IVG7].istop; -#ifdef CONFIG_BF54x +#if defined(CONFIG_BF54x) || defined(CONFIG_BF52x) unsigned long sic_status[3]; SSYNC(); sic_status[0] = bfin_read_SIC_ISR(0) & bfin_read_SIC_IMASK(0); sic_status[1] = bfin_read_SIC_ISR(1) & bfin_read_SIC_IMASK(1); +#ifdef CONFIG_BF54x sic_status[2] = bfin_read_SIC_ISR(2) & bfin_read_SIC_IMASK(2); - +#endif for (;; ivg++) { if (ivg >= ivg_stop) { atomic_inc(&num_spurious); diff --git a/include/asm-blackfin/bf5xx_timers.h b/include/asm-blackfin/bf5xx_timers.h index 86c770321b6..8e8246f32fe 100644 --- a/include/asm-blackfin/bf5xx_timers.h +++ b/include/asm-blackfin/bf5xx_timers.h @@ -16,7 +16,7 @@ /* * BF537: 8 timers: */ -#if defined(CONFIG_BF537) +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) # define MAX_BLACKFIN_GPTIMERS 8 # define TIMER0_GROUP_REG TIMER_ENABLE #endif diff --git a/include/asm-blackfin/gpio.h b/include/asm-blackfin/gpio.h index dd203cd9379..33ce98ef7e0 100644 --- a/include/asm-blackfin/gpio.h +++ b/include/asm-blackfin/gpio.h @@ -29,6 +29,7 @@ /* * Number BF537/6/4 BF561 BF533/2/1 +* BF527/5/2 * * GPIO_0 PF0 PF0 PF0 * GPIO_1 PF1 PF1 PF1 @@ -164,7 +165,7 @@ #endif -#ifdef BF537_FAMILY +#if defined(BF527_FAMILY) || defined(BF537_FAMILY) #define MAX_BLACKFIN_GPIOS 48 #define GPIO_PF0 0 diff --git a/include/asm-blackfin/mach-bf527/anomaly.h b/include/asm-blackfin/mach-bf527/anomaly.h index 991db986cd4..a89120445be 100644 --- a/include/asm-blackfin/mach-bf527/anomaly.h +++ b/include/asm-blackfin/mach-bf527/anomaly.h @@ -38,4 +38,12 @@ /* Anomalies that don't exist on this proc */ #define ANOMALY_05000323 (0) +#define ANOMALY_05000244 (0) +#define ANOMALY_05000198 (0) +#define ANOMALY_05000125 (0) +#define ANOMALY_05000158 (0) +#define ANOMALY_05000273 (0) +#define ANOMALY_05000263 (0) +#define ANOMALY_05000311 (0) +#define ANOMALY_05000230 (0) #endif diff --git a/include/asm-blackfin/mach-bf527/bf527.h b/include/asm-blackfin/mach-bf527/bf527.h new file mode 100644 index 00000000000..056eb4b9cd2 --- /dev/null +++ b/include/asm-blackfin/mach-bf527/bf527.h @@ -0,0 +1,127 @@ +/* + * File: include/asm-blackfin/mach-bf527/bf527.h + * Based on: include/asm-blackfin/mach-bf537/bf537.h + * Author: Michael Hennerich (michael.hennerich@analog.com) + * + * Created: + * Description: SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF527 + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, see the file COPYING, or write + * to the Free Software Foundation, Inc., + * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __MACH_BF527_H__ +#define __MACH_BF527_H__ + +#define SUPPORTED_REVID 2 + +#define OFFSET_(x) ((x) & 0x0000FFFF) + +/*some misc defines*/ +#define IMASK_IVG15 0x8000 +#define IMASK_IVG14 0x4000 +#define IMASK_IVG13 0x2000 +#define IMASK_IVG12 0x1000 + +#define IMASK_IVG11 0x0800 +#define IMASK_IVG10 0x0400 +#define IMASK_IVG9 0x0200 +#define IMASK_IVG8 0x0100 + +#define IMASK_IVG7 0x0080 +#define IMASK_IVGTMR 0x0040 +#define IMASK_IVGHW 0x0020 + +/***************************/ + +#define BFIN_DSUBBANKS 4 +#define BFIN_DWAYS 2 +#define BFIN_DLINES 64 +#define BFIN_ISUBBANKS 4 +#define BFIN_IWAYS 4 +#define BFIN_ILINES 32 + +#define WAY0_L 0x1 +#define WAY1_L 0x2 +#define WAY01_L 0x3 +#define WAY2_L 0x4 +#define WAY02_L 0x5 +#define WAY12_L 0x6 +#define WAY012_L 0x7 + +#define WAY3_L 0x8 +#define WAY03_L 0x9 +#define WAY13_L 0xA +#define WAY013_L 0xB + +#define WAY32_L 0xC +#define WAY320_L 0xD +#define WAY321_L 0xE +#define WAYALL_L 0xF + +#define DMC_ENABLE (2<<2) /*yes, 2, not 1 */ + +/********************************* EBIU Settings ************************************/ +#define AMBCTL0VAL ((CONFIG_BANK_1 << 16) | CONFIG_BANK_0) +#define AMBCTL1VAL ((CONFIG_BANK_3 << 16) | CONFIG_BANK_2) + +#ifdef CONFIG_C_AMBEN_ALL +#define V_AMBEN AMBEN_ALL +#endif +#ifdef CONFIG_C_AMBEN +#define V_AMBEN 0x0 +#endif +#ifdef CONFIG_C_AMBEN_B0 +#define V_AMBEN AMBEN_B0 +#endif +#ifdef CONFIG_C_AMBEN_B0_B1 +#define V_AMBEN AMBEN_B0_B1 +#endif +#ifdef CONFIG_C_AMBEN_B0_B1_B2 +#define V_AMBEN AMBEN_B0_B1_B2 +#endif +#ifdef CONFIG_C_AMCKEN +#define V_AMCKEN AMCKEN +#else +#define V_AMCKEN 0x0 +#endif +#ifdef CONFIG_C_CDPRIO +#define V_CDPRIO 0x100 +#else +#define V_CDPRIO 0x0 +#endif + +#define AMGCTLVAL (V_AMBEN | V_AMCKEN | V_CDPRIO) + +#ifdef CONFIG_BF527 +#define CPU "BF527" +#endif +#ifdef CONFIG_BF525 +#define CPU "BF525" +#endif +#ifdef CONFIG_BF522 +#define CPU "BF522" +#endif +#ifndef CPU +#define CPU "UNKNOWN" +#define CPUID 0x0 +#endif + +#endif /* __MACH_BF527_H__ */ diff --git a/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h new file mode 100644 index 00000000000..0b867e6a76c --- /dev/null +++ b/include/asm-blackfin/mach-bf527/bfin_serial_5xx.h @@ -0,0 +1,152 @@ +#include +#include +#include + +#define NR_PORTS 2 + +#define OFFSET_THR 0x00 /* Transmit Holding register */ +#define OFFSET_RBR 0x00 /* Receive Buffer register */ +#define OFFSET_DLL 0x00 /* Divisor Latch (Low-Byte) */ +#define OFFSET_IER 0x04 /* Interrupt Enable Register */ +#define OFFSET_DLH 0x04 /* Divisor Latch (High-Byte) */ +#define OFFSET_IIR 0x08 /* Interrupt Identification Register */ +#define OFFSET_LCR 0x0C /* Line Control Register */ +#define OFFSET_MCR 0x10 /* Modem Control Register */ +#define OFFSET_LSR 0x14 /* Line Status Register */ +#define OFFSET_MSR 0x18 /* Modem Status Register */ +#define OFFSET_SCR 0x1C /* SCR Scratch Register */ +#define OFFSET_GCTL 0x24 /* Global Control Register */ + +#define UART_GET_CHAR(uart) bfin_read16(((uart)->port.membase + OFFSET_RBR)) +#define UART_GET_DLL(uart) bfin_read16(((uart)->port.membase + OFFSET_DLL)) +#define UART_GET_IER(uart) bfin_read16(((uart)->port.membase + OFFSET_IER)) +#define UART_GET_DLH(uart) bfin_read16(((uart)->port.membase + OFFSET_DLH)) +#define UART_GET_IIR(uart) bfin_read16(((uart)->port.membase + OFFSET_IIR)) +#define UART_GET_LCR(uart) bfin_read16(((uart)->port.membase + OFFSET_LCR)) +#define UART_GET_LSR(uart) bfin_read16(((uart)->port.membase + OFFSET_LSR)) +#define UART_GET_GCTL(uart) bfin_read16(((uart)->port.membase + OFFSET_GCTL)) + +#define UART_PUT_CHAR(uart, v) bfin_write16(((uart)->port.membase + OFFSET_THR), v) +#define UART_PUT_DLL(uart, v) bfin_write16(((uart)->port.membase + OFFSET_DLL), v) +#define UART_PUT_IER(uart, v) bfin_write16(((uart)->port.membase + OFFSET_IER), v) +#define UART_PUT_DLH(uart, v) bfin_write16(((uart)->port.membase + OFFSET_DLH), v) +#define UART_PUT_LCR(uart, v) bfin_write16(((uart)->port.membase + OFFSET_LCR), v) +#define UART_PUT_GCTL(uart, v) bfin_write16(((uart)->port.membase + OFFSET_GCTL), v) + +#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) +# define CONFIG_SERIAL_BFIN_CTSRTS + +# ifndef CONFIG_UART0_CTS_PIN +# define CONFIG_UART0_CTS_PIN -1 +# endif + +# ifndef CONFIG_UART0_RTS_PIN +# define CONFIG_UART0_RTS_PIN -1 +# endif + +# ifndef CONFIG_UART1_CTS_PIN +# define CONFIG_UART1_CTS_PIN -1 +# endif + +# ifndef CONFIG_UART1_RTS_PIN +# define CONFIG_UART1_RTS_PIN -1 +# endif +#endif +/* + * The pin configuration is different from schematic + */ +struct bfin_serial_port { + struct uart_port port; + unsigned int old_status; +#ifdef CONFIG_SERIAL_BFIN_DMA + int tx_done; + int tx_count; + struct circ_buf rx_dma_buf; + struct timer_list rx_dma_timer; + int rx_dma_nrows; + unsigned int tx_dma_channel; + unsigned int rx_dma_channel; + struct work_struct tx_dma_workqueue; +#else + struct work_struct cts_workqueue; +#endif +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + int cts_pin; + int rts_pin; +#endif +}; + +struct bfin_serial_port bfin_serial_ports[NR_PORTS]; +struct bfin_serial_res { + unsigned long uart_base_addr; + int uart_irq; +#ifdef CONFIG_SERIAL_BFIN_DMA + unsigned int uart_tx_dma_channel; + unsigned int uart_rx_dma_channel; +#endif +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + int uart_cts_pin; + int uart_rts_pin; +#endif +}; + +struct bfin_serial_res bfin_serial_resource[] = { +#ifdef CONFIG_SERIAL_BFIN_UART0 + { + 0xFFC00400, + IRQ_UART0_RX, +#ifdef CONFIG_SERIAL_BFIN_DMA + CH_UART0_TX, + CH_UART0_RX, +#endif +#ifdef CONFIG_BFIN_UART0_CTSRTS + CONFIG_UART0_CTS_PIN, + CONFIG_UART0_RTS_PIN, +#endif + }, +#endif +#ifdef CONFIG_SERIAL_BFIN_UART1 + { + 0xFFC02000, + IRQ_UART1_RX, +#ifdef CONFIG_SERIAL_BFIN_DMA + CH_UART1_TX, + CH_UART1_RX, +#endif +#ifdef CONFIG_BFIN_UART1_CTSRTS + CONFIG_UART1_CTS_PIN, + CONFIG_UART1_RTS_PIN, +#endif + }, +#endif +}; + +int nr_ports = ARRAY_SIZE(bfin_serial_resource); + +#define DRIVER_NAME "bfin-uart" + +static void bfin_serial_hw_init(struct bfin_serial_port *uart) +{ + +#ifdef CONFIG_SERIAL_BFIN_UART0 + peripheral_request(P_UART0_TX, DRIVER_NAME); + peripheral_request(P_UART0_RX, DRIVER_NAME); +#endif + +#ifdef CONFIG_SERIAL_BFIN_UART1 + peripheral_request(P_UART1_TX, DRIVER_NAME); + peripheral_request(P_UART1_RX, DRIVER_NAME); +#endif + +#ifdef CONFIG_SERIAL_BFIN_CTSRTS + if (uart->cts_pin >= 0) { + gpio_request(uart->cts_pin, DRIVER_NAME); + gpio_direction_input(uart->cts_pin); + } + + if (uart->rts_pin >= 0) { + gpio_request(uart->rts_pin, DRIVER_NAME); + gpio_direction_output(uart->rts_pin); + } +#endif +} diff --git a/include/asm-blackfin/mach-bf527/blackfin.h b/include/asm-blackfin/mach-bf527/blackfin.h new file mode 100644 index 00000000000..1bd07e30781 --- /dev/null +++ b/include/asm-blackfin/mach-bf527/blackfin.h @@ -0,0 +1,78 @@ +/* + * File: include/asm-blackfin/mach-bf527/blackfin.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#ifndef _MACH_BLACKFIN_H_ +#define _MACH_BLACKFIN_H_ + +#define BF527_FAMILY + +#include "bf527.h" +#include "mem_map.h" +#include "defBF522.h" +#include "anomaly.h" + +#if defined(CONFIG_BF527) +#include "defBF527.h" +#endif + +#if defined(CONFIG_BF525) +#include "defBF525.h" +#endif + +#if !defined(__ASSEMBLY__) +#include "cdefBF522.h" + +#if defined(CONFIG_BF527) +#include "cdefBF527.h" +#endif + +#if defined(CONFIG_BF525) +#include "cdefBF525.h" +#endif +#endif + +/* UART_IIR Register */ +#define STATUS(x) ((x << 1) & 0x06) +#define STATUS_P1 0x02 +#define STATUS_P0 0x01 + +/* DPMC*/ +#define bfin_read_STOPCK_OFF() bfin_read_STOPCK() +#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val) +#define STOPCK_OFF STOPCK + +/* PLL_DIV Masks */ +#define CCLK_DIV1 CSEL_DIV1 /* CCLK = VCO / 1 */ +#define CCLK_DIV2 CSEL_DIV2 /* CCLK = VCO / 2 */ +#define CCLK_DIV4 CSEL_DIV4 /* CCLK = VCO / 4 */ +#define CCLK_DIV8 CSEL_DIV8 /* CCLK = VCO / 8 */ + +#endif diff --git a/include/asm-blackfin/mach-bf527/cdefBF52x_base.h b/include/asm-blackfin/mach-bf527/cdefBF52x_base.h index 5f801a0ef79..3f4de5d9d4c 100644 --- a/include/asm-blackfin/mach-bf527/cdefBF52x_base.h +++ b/include/asm-blackfin/mach-bf527/cdefBF52x_base.h @@ -45,8 +45,8 @@ #define bfin_write_PLL_STAT(val) bfin_write16(PLL_STAT, val) #define bfin_read_PLL_LOCKCNT() bfin_read16(PLL_LOCKCNT) #define bfin_write_PLL_LOCKCNT(val) bfin_write16(PLL_LOCKCNT, val) -#define bfin_read_CHIPID() bfin_read16(CHIPID) -#define bfin_write_CHIPID(val) bfin_write16(CHIPID, val) +#define bfin_read_CHIPID() bfin_read32(CHIPID) +#define bfin_write_CHIPID(val) bfin_write32(CHIPID, val) /* System Interrupt Controller (0xFFC00100 - 0xFFC001FF) */ @@ -59,9 +59,8 @@ #define bfin_write_SIC_RVECT(val) bfin_write32(SIC_RVECT, val) #define bfin_read_SIC_IMASK0() bfin_read32(SIC_IMASK0) #define bfin_write_SIC_IMASK0(val) bfin_write32(SIC_IMASK0, val) -/* legacy register name (below) provided for backwards code compatibility */ -#define bfin_read_SIC_IMASK() bfin_read32(SIC_IMASK) -#define bfin_write_SIC_IMASK(val) bfin_write32(SIC_IMASK, val) +#define bfin_read_SIC_IMASK(x) bfin_read32(SIC_IMASK0 + (x << 6)) +#define bfin_write_SIC_IMASK(x, val) bfin_write32((SIC_IMASK0 + (x << 6)), val) #define bfin_read_SIC_IAR0() bfin_read32(SIC_IAR0) #define bfin_write_SIC_IAR0(val) bfin_write32(SIC_IAR0, val) @@ -74,15 +73,13 @@ #define bfin_read_SIC_ISR0() bfin_read32(SIC_ISR0) #define bfin_write_SIC_ISR0(val) bfin_write32(SIC_ISR0, val) -/* legacy register name (below) provided for backwards code compatibility */ -#define bfin_read_SIC_ISR() bfin_read32(SIC_ISR) -#define bfin_write_SIC_ISR(val) bfin_write32(SIC_ISR, val) +#define bfin_read_SIC_ISR(x) bfin_read32(SIC_ISR0 + (x << 6)) +#define bfin_write_SIC_ISR(x, val) bfin_write32((SIC_ISR0 + (x << 6)), val) #define bfin_read_SIC_IWR0() bfin_read32(SIC_IWR0) #define bfin_write_SIC_IWR0(val) bfin_write32(SIC_IWR0, val) -/* legacy register name (below) provided for backwards code compatibility */ -#define bfin_read_SIC_IWR() bfin_read32(SIC_IWR) -#define bfin_write_SIC_IWR(val) bfin_write32(SIC_IWR, val) +#define bfin_read_SIC_IWR(x) bfin_read32(SIC_IWR0 + (x << 6)) +#define bfin_write_SIC_IWR(x, val) bfin_write32((SIC_IWR0 + (x << 6)), val) /* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */ diff --git a/include/asm-blackfin/mach-bf527/defBF527.h b/include/asm-blackfin/mach-bf527/defBF527.h index 2be3293f9e2..82134f578f3 100644 --- a/include/asm-blackfin/mach-bf527/defBF527.h +++ b/include/asm-blackfin/mach-bf527/defBF527.h @@ -32,12 +32,12 @@ #define _DEF_BF527_H /* Include all Core registers and bit definitions */ -#include +#include /* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */ /* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */ -#include +#include "defBF52x_base.h" /* The following are the #defines needed by ADSP-BF527 that are not in the common header */ /* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */ diff --git a/include/asm-blackfin/mach-bf527/defBF52x_base.h b/include/asm-blackfin/mach-bf527/defBF52x_base.h index b1ff67db01f..d6c24c54699 100644 --- a/include/asm-blackfin/mach-bf527/defBF52x_base.h +++ b/include/asm-blackfin/mach-bf527/defBF52x_base.h @@ -52,13 +52,13 @@ #define SYSCR 0xFFC00104 /* System Configuration Register */ #define SIC_RVECT 0xFFC00108 /* Interrupt Reset Vector Address Register */ -#define SIC_IMASK 0xFFC0010C /* Interrupt Mask Register */ +#define SIC_IMASK0 0xFFC0010C /* Interrupt Mask Register */ #define SIC_IAR0 0xFFC00110 /* Interrupt Assignment Register 0 */ #define SIC_IAR1 0xFFC00114 /* Interrupt Assignment Register 1 */ #define SIC_IAR2 0xFFC00118 /* Interrupt Assignment Register 2 */ #define SIC_IAR3 0xFFC0011C /* Interrupt Assignment Register 3 */ -#define SIC_ISR 0xFFC00120 /* Interrupt Status Register */ -#define SIC_IWR 0xFFC00124 /* Interrupt Wakeup Register */ +#define SIC_ISR0 0xFFC00120 /* Interrupt Status Register */ +#define SIC_IWR0 0xFFC00124 /* Interrupt Wakeup Register */ /* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */ #define SIC_IMASK1 0xFFC0014C /* Interrupt Mask register of SIC2 */ @@ -691,6 +691,8 @@ /* ************* SYSTEM INTERRUPT CONTROLLER MASKS *************************************/ /* Peripheral Masks For SIC_ISR, SIC_IWR, SIC_IMASK */ + +#if 0 #define IRQ_PLL_WAKEUP 0x00000001 /* PLL Wakeup Interrupt */ #define IRQ_ERROR1 0x00000002 /* Error Interrupt (DMA, DMARx Block, DMARx Overflow) */ @@ -732,6 +734,7 @@ #define IRQ_DMA15 0x40000000 /* DMA Channels 15 (MDMA0 Destination) TX Interrupt */ #define IRQ_WDOG 0x80000000 /* Software Watchdog Timer Interrupt */ #define IRQ_PFB_PORTG 0x10000000 /* PF Port G (PF31:16) Interrupt B */ +#endif /* SIC_IAR0 Macros */ #define P0_IVG(x) (((x)&0xF)-7) /* Peripheral #0 assigned IVG #x */ diff --git a/include/asm-blackfin/mach-bf527/dma.h b/include/asm-blackfin/mach-bf527/dma.h new file mode 100644 index 00000000000..a41627ae913 --- /dev/null +++ b/include/asm-blackfin/mach-bf527/dma.h @@ -0,0 +1,60 @@ +/* + * file: include/asm-blackfin/mach-bf527/dma.h + * based on: include/asm-blackfin/mach-bf537/dma.h + * author: Michael Hennerich (michael.hennerich@analog.com) + * + * created: + * description: + * system DMA map + * rev: + * + * modified: + * + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _MACH_DMA_H_ +#define _MACH_DMA_H_ + +#define MAX_BLACKFIN_DMA_CHANNEL 16 + +#define CH_PPI 0 /* PPI receive/transmit or NFC */ +#define CH_NFC 0 /* PPI receive/transmit or NFC */ +#define CH_EMAC_RX 1 /* Ethernet MAC receive or HOSTDP */ +#define CH_EMAC_HOSTDP 1 /* Ethernet MAC receive or HOSTDP */ +#define CH_EMAC_TX 2 /* Ethernet MAC transmit or NFC */ +#define CH_SPORT0_RX 3 /* SPORT0 receive */ +#define CH_SPORT0_TX 4 /* SPORT0 transmit */ +#define CH_SPORT1_RX 5 /* SPORT1 receive */ +#define CH_SPORT1_TX 6 /* SPORT1 transmit */ +#define CH_SPI 7 /* SPI transmit/receive */ +#define CH_UART0_RX 8 /* UART0 receive */ +#define CH_UART0_TX 9 /* UART0 transmit */ +#define CH_UART1_RX 10 /* UART1 receive */ +#define CH_UART1_TX 11 /* UART1 transmit */ + +#define CH_MEM_STREAM0_DEST 12 /* TX */ +#define CH_MEM_STREAM0_SRC 13 /* RX */ +#define CH_MEM_STREAM1_DEST 14 /* TX */ +#define CH_MEM_STREAM1_SRC 15 /* RX */ + +extern int channel2irq(unsigned int channel); +extern struct dma_register *base_addr[]; + +#endif diff --git a/include/asm-blackfin/mach-bf527/irq.h b/include/asm-blackfin/mach-bf527/irq.h new file mode 100644 index 00000000000..304f5bcfebe --- /dev/null +++ b/include/asm-blackfin/mach-bf527/irq.h @@ -0,0 +1,263 @@ +/* + * file: include/asm-blackfin/mach-bf527/irq.h + * based on: include/asm-blackfin/mach-bf537/irq.h + * author: Michael Hennerich (michael.hennerich@analog.com) + * + * created: + * description: + * system mmr register map + * rev: + * + * modified: + * + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _BF527_IRQ_H_ +#define _BF527_IRQ_H_ + +/* + * Interrupt source definitions + Event Source Core Event Name + Core Emulation ** + Events (highest priority) EMU 0 + Reset RST 1 + NMI NMI 2 + Exception EVX 3 + Reserved -- 4 + Hardware Error IVHW 5 + Core Timer IVTMR 6 * + + ..... + + Software Interrupt 1 IVG14 31 + Software Interrupt 2 -- + (lowest priority) IVG15 32 * +*/ + +#define NR_PERI_INTS (2 * 32) + +/* The ABSTRACT IRQ definitions */ +/** the first seven of the following are fixed, the rest you change if you need to **/ +#define IRQ_EMU 0 /* Emulation */ +#define IRQ_RST 1 /* reset */ +#define IRQ_NMI 2 /* Non Maskable */ +#define IRQ_EVX 3 /* Exception */ +#define IRQ_UNUSED 4 /* - unused interrupt */ +#define IRQ_HWERR 5 /* Hardware Error */ +#define IRQ_CORETMR 6 /* Core timer */ + +#define BFIN_IRQ(x) ((x) + 7) + +#define IRQ_PLL_WAKEUP BFIN_IRQ(0) /* PLL Wakeup Interrupt */ +#define IRQ_DMA0_ERROR BFIN_IRQ(1) /* DMA Error 0 (generic) */ +#define IRQ_DMAR0_BLK BFIN_IRQ(2) /* DMAR0 Block Interrupt */ +#define IRQ_DMAR1_BLK BFIN_IRQ(3) /* DMAR1 Block Interrupt */ +#define IRQ_DMAR0_OVR BFIN_IRQ(4) /* DMAR0 Overflow Error */ +#define IRQ_DMAR1_OVR BFIN_IRQ(5) /* DMAR1 Overflow Error */ +#define IRQ_PPI_ERROR BFIN_IRQ(6) /* PPI Error */ +#define IRQ_MAC_ERROR BFIN_IRQ(7) /* MAC Status */ +#define IRQ_SPORT0_ERROR BFIN_IRQ(8) /* SPORT0 Status */ +#define IRQ_SPORT1_ERROR BFIN_IRQ(9) /* SPORT1 Status */ +#define IRQ_UART0_ERROR BFIN_IRQ(12) /* UART0 Status */ +#define IRQ_UART1_ERROR BFIN_IRQ(13) /* UART1 Status */ +#define IRQ_RTC BFIN_IRQ(14) /* RTC */ +#define IRQ_PPI BFIN_IRQ(15) /* DMA Channel 0 (PPI/NAND) */ +#define IRQ_SPORT0_RX BFIN_IRQ(16) /* DMA 3 Channel (SPORT0 RX) */ +#define IRQ_SPORT0_TX BFIN_IRQ(17) /* DMA 4 Channel (SPORT0 TX) */ +#define IRQ_SPORT1_RX BFIN_IRQ(18) /* DMA 5 Channel (SPORT1 RX) */ +#define IRQ_SPORT1_TX BFIN_IRQ(19) /* DMA 6 Channel (SPORT1 TX) */ +#define IRQ_TWI BFIN_IRQ(20) /* TWI */ +#define IRQ_SPI BFIN_IRQ(21) /* DMA 7 Channel (SPI) */ +#define IRQ_UART0_RX BFIN_IRQ(22) /* DMA8 Channel (UART0 RX) */ +#define IRQ_UART0_TX BFIN_IRQ(23) /* DMA9 Channel (UART0 TX) */ +#define IRQ_UART1_RX BFIN_IRQ(24) /* DMA10 Channel (UART1 RX) */ +#define IRQ_UART1_TX BFIN_IRQ(25) /* DMA11 Channel (UART1 TX) */ +#define IRQ_OPTSEC BFIN_IRQ(26) /* OTPSEC Interrupt */ +#define IRQ_CNT BFIN_IRQ(27) /* GP Counter */ +#define IRQ_MAC_RX BFIN_IRQ(28) /* DMA1 Channel (MAC RX/HDMA) */ +#define IRQ_PORTH_INTA BFIN_IRQ(29) /* Port H Interrupt A */ +#define IRQ_MAC_TX BFIN_IRQ(30) /* DMA2 Channel (MAC TX/NAND) */ +#define IRQ_NFC BFIN_IRQ(30) /* DMA2 Channel (MAC TX/NAND) */ +#define IRQ_PORTH_INTB BFIN_IRQ(31) /* Port H Interrupt B */ +#define IRQ_TMR0 BFIN_IRQ(32) /* Timer 0 */ +#define IRQ_TMR1 BFIN_IRQ(33) /* Timer 1 */ +#define IRQ_TMR2 BFIN_IRQ(34) /* Timer 2 */ +#define IRQ_TMR3 BFIN_IRQ(35) /* Timer 3 */ +#define IRQ_TMR4 BFIN_IRQ(36) /* Timer 4 */ +#define IRQ_TMR5 BFIN_IRQ(37) /* Timer 5 */ +#define IRQ_TMR6 BFIN_IRQ(38) /* Timer 6 */ +#define IRQ_TMR7 BFIN_IRQ(39) /* Timer 7 */ +#define IRQ_PORTG_INTA BFIN_IRQ(40) /* Port G Interrupt A */ +#define IRQ_PORTG_INTB BFIN_IRQ(41) /* Port G Interrupt B */ +#define IRQ_MEM_DMA0 BFIN_IRQ(42) /* MDMA Stream 0 */ +#define IRQ_MEM_DMA1 BFIN_IRQ(43) /* MDMA Stream 1 */ +#define IRQ_WATCH BFIN_IRQ(44) /* Software Watchdog Timer */ +#define IRQ_PORTF_INTA BFIN_IRQ(45) /* Port F Interrupt A */ +#define IRQ_PORTF_INTB BFIN_IRQ(46) /* Port F Interrupt B */ +#define IRQ_SPI_ERROR BFIN_IRQ(47) /* SPI Status */ +#define IRQ_NFC_ERROR BFIN_IRQ(48) /* NAND Error */ +#define IRQ_HDMA_ERROR BFIN_IRQ(49) /* HDMA Error */ +#define IRQ_HDMA BFIN_IRQ(50) /* HDMA (TFI) */ +#define IRQ_USB_EINT BFIN_IRQ(51) /* USB_EINT Interrupt */ +#define IRQ_USB_INT0 BFIN_IRQ(52) /* USB_INT0 Interrupt */ +#define IRQ_USB_INT1 BFIN_IRQ(53) /* USB_INT1 Interrupt */ +#define IRQ_USB_INT2 BFIN_IRQ(54) /* USB_INT2 Interrupt */ +#define IRQ_USB_DMA BFIN_IRQ(55) /* USB_DMAINT Interrupt */ + +#define SYS_IRQS BFIN_IRQ(63) /* 70 */ + +#define IRQ_PF0 71 +#define IRQ_PF1 72 +#define IRQ_PF2 73 +#define IRQ_PF3 74 +#define IRQ_PF4 75 +#define IRQ_PF5 76 +#define IRQ_PF6 77 +#define IRQ_PF7 78 +#define IRQ_PF8 79 +#define IRQ_PF9 80 +#define IRQ_PF10 81 +#define IRQ_PF11 82 +#define IRQ_PF12 83 +#define IRQ_PF13 84 +#define IRQ_PF14 85 +#define IRQ_PF15 86 + +#define IRQ_PG0 87 +#define IRQ_PG1 88 +#define IRQ_PG2 89 +#define IRQ_PG3 90 +#define IRQ_PG4 91 +#define IRQ_PG5 92 +#define IRQ_PG6 93 +#define IRQ_PG7 94 +#define IRQ_PG8 95 +#define IRQ_PG9 96 +#define IRQ_PG10 97 +#define IRQ_PG11 98 +#define IRQ_PG12 99 +#define IRQ_PG13 100 +#define IRQ_PG14 101 +#define IRQ_PG15 102 + +#define IRQ_PH0 103 +#define IRQ_PH1 104 +#define IRQ_PH2 105 +#define IRQ_PH3 106 +#define IRQ_PH4 107 +#define IRQ_PH5 108 +#define IRQ_PH6 109 +#define IRQ_PH7 110 +#define IRQ_PH8 111 +#define IRQ_PH9 112 +#define IRQ_PH10 113 +#define IRQ_PH11 114 +#define IRQ_PH12 115 +#define IRQ_PH13 116 +#define IRQ_PH14 117 +#define IRQ_PH15 118 + +#define GPIO_IRQ_BASE IRQ_PF0 + +#ifdef CONFIG_IRQCHIP_DEMUX_GPIO +#define NR_IRQS (IRQ_PH15+1) +#else +#define NR_IRQS (SYS_IRQS+1) +#endif + +#define IVG7 7 +#define IVG8 8 +#define IVG9 9 +#define IVG10 10 +#define IVG11 11 +#define IVG12 12 +#define IVG13 13 +#define IVG14 14 +#define IVG15 15 + +/* IAR0 BIT FIELDS */ +#define IRQ_PLL_WAKEUP_POS 0 +#define IRQ_DMA0_ERROR_POS 4 +#define IRQ_DMAR0_BLK_POS 8 +#define IRQ_DMAR1_BLK_POS 12 +#define IRQ_DMAR0_OVR_POS 16 +#define IRQ_DMAR1_OVR_POS 20 +#define IRQ_PPI_ERROR_POS 24 +#define IRQ_MAC_ERROR_POS 28 + +/* IAR1 BIT FIELDS */ +#define IRQ_SPORT0_ERROR_POS 0 +#define IRQ_SPORT1_ERROR_POS 4 +#define IRQ_UART0_ERROR_POS 16 +#define IRQ_UART1_ERROR_POS 20 +#define IRQ_RTC_POS 24 +#define IRQ_PPI_POS 28 + +/* IAR2 BIT FIELDS */ +#define IRQ_SPORT0_RX_POS 0 +#define IRQ_SPORT0_TX_POS 4 +#define IRQ_SPORT1_RX_POS 8 +#define IRQ_SPORT1_TX_POS 12 +#define IRQ_TWI_POS 16 +#define IRQ_SPI_POS 20 +#define IRQ_UART0_RX_POS 24 +#define IRQ_UART0_TX_POS 28 + +/* IAR3 BIT FIELDS */ +#define IRQ_UART1_RX_POS 0 +#define IRQ_UART1_TX_POS 4 +#define IRQ_OPTSEC_POS 8 +#define IRQ_CNT_POS 12 +#define IRQ_MAC_RX_POS 16 +#define IRQ_PORTH_INTA_POS 20 +#define IRQ_MAC_TX_POS 24 +#define IRQ_PORTH_INTB_POS 28 + +/* IAR4 BIT FIELDS */ +#define IRQ_TMR0_POS 0 +#define IRQ_TMR1_POS 4 +#define IRQ_TMR2_POS 8 +#define IRQ_TMR3_POS 12 +#define IRQ_TMR4_POS 16 +#define IRQ_TMR5_POS 20 +#define IRQ_TMR6_POS 24 +#define IRQ_TMR7_POS 28 + +/* IAR5 BIT FIELDS */ +#define IRQ_PORTG_INTA_POS 0 +#define IRQ_PORTG_INTB_POS 4 +#define IRQ_MEM_DMA0_POS 8 +#define IRQ_MEM_DMA1_POS 12 +#define IRQ_WATCH_POS 16 +#define IRQ_PORTF_INTA_POS 20 +#define IRQ_PORTF_INTB_POS 24 +#define IRQ_SPI_ERROR_POS 28 + +/* IAR6 BIT FIELDS */ +#define IRQ_NFC_ERROR_POS 0 +#define IRQ_HDMA_ERROR_POS 4 +#define IRQ_HDMA_POS 8 +#define IRQ_USB_EINT_POS 12 +#define IRQ_USB_INT0_POS 16 +#define IRQ_USB_INT1_POS 20 +#define IRQ_USB_INT2_POS 24 +#define IRQ_USB_DMA_POS 28 + +#endif /* _BF527_IRQ_H_ */ diff --git a/include/asm-blackfin/mach-bf527/mem_init.h b/include/asm-blackfin/mach-bf527/mem_init.h new file mode 100644 index 00000000000..008ca66719e --- /dev/null +++ b/include/asm-blackfin/mach-bf527/mem_init.h @@ -0,0 +1,337 @@ +/* + * File: include/asm-blackfin/mach-bf527/mem_init.h + * Based on: + * Author: + * + * Created: + * Description: + * + * Rev: + * + * Modified: + * Copyright 2004-2007 Analog Devices Inc. + * + * Bugs: Enter bugs at http://blackfin.uclinux.org/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2, or (at your option) + * any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; see the file COPYING. + * If not, write to the Free Software Foundation, + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + */ + +#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_MT48LC16M8A2TG_75 || CONFIG_MEM_GENERIC_BOARD || CONFIG_MEM_MT48LC32M8A2_75 || CONFIG_MEM_MT48LC32M16A2TG_75) +#if (CONFIG_SCLK_HZ > 119402985) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_7 +#define SDRAM_tRAS_num 7 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_6 +#define SDRAM_tRAS_num 6 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_5 +#define SDRAM_tRAS_num 5 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_4 +#define SDRAM_tRAS_num 4 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866) +#define SDRAM_tRP TRP_2 +#define SDRAM_tRP_num 2 +#define SDRAM_tRAS TRAS_3 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_2 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_4 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_3 +#define SDRAM_tRAS_num 3 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_2 +#define SDRAM_tRAS_num 2 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#if (CONFIG_SCLK_HZ <= 29850746) +#define SDRAM_tRP TRP_1 +#define SDRAM_tRP_num 1 +#define SDRAM_tRAS TRAS_1 +#define SDRAM_tRAS_num 1 +#define SDRAM_tRCD TRCD_1 +#define SDRAM_tWR TWR_2 +#endif +#endif + +#if (CONFIG_MEM_MT48LC16M16A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC16M8A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 4096 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC32M8A2_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC64M4A2FB_7E) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_GENERIC_BOARD) + /*SDRAM INFORMATION: Modify this for your board */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_MT48LC32M16A2TG_75) + /*SDRAM INFORMATION: */ +#define SDRAM_Tref 64 /* Refresh period in milliseconds */ +#define SDRAM_NRA 8192 /* Number of row addresses in SDRAM */ +#define SDRAM_CL CL_3 +#endif + +#if (CONFIG_MEM_SIZE == 128) +#define SDRAM_SIZE EBSZ_128 +#endif +#if (CONFIG_MEM_SIZE == 64) +#define SDRAM_SIZE EBSZ_64 +#endif +#if (CONFIG_MEM_SIZE == 32) +#define SDRAM_SIZE EBSZ_32 +#endif +#if (CONFIG_MEM_SIZE == 16) +#define SDRAM_SIZE EBSZ_16 +#endif +#if (CONFIG_MEM_ADD_WIDTH == 11) +#define SDRAM_WIDTH EBCAW_11 +#endif +#if (CONFIG_MEM_ADD_WIDTH == 10) +#define SDRAM_WIDTH EBCAW_10 +#endif +#if (CONFIG_MEM_ADD_WIDTH == 9) +#define SDRAM_WIDTH EBCAW_9 +#endif +#if (CONFIG_MEM_ADD_WIDTH == 8) +#define SDRAM_WIDTH EBCAW_8 +#endif + +#define mem_SDBCTL (SDRAM_WIDTH | SDRAM_SIZE | EBE) + +/* Equation from section 17 (p17-46) of BF533 HRM */ +#define mem_SDRRC (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num) + +/* Enable SCLK Out */ +#define mem_SDGCTL (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS) + +#if defined CONFIG_CLKIN_HALF +#define CLKIN_HALF 1 +#else +#define CLKIN_HALF 0 +#endif + +#if defined CONFIG_PLL_BYPASS +#define PLL_BYPASS 1 +#else +#define PLL_BYPASS 0 +#endif + +/***************************************Currently Not Being Used *********************************/ +#define flash_EBIU_AMBCTL_WAT ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_RAT ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_HT ((CONFIG_FLASH_SPEED_BHT * 4) / (4000000000 / CONFIG_SCLK_HZ)) +#define flash_EBIU_AMBCTL_ST ((CONFIG_FLASH_SPEED_BST * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 +#define flash_EBIU_AMBCTL_TT ((CONFIG_FLASH_SPEED_BTT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1 + +#if (flash_EBIU_AMBCTL_TT > 3) +#define flash_EBIU_AMBCTL0_TT B0TT_4 +#endif +#if (flash_EBIU_AMBCTL_TT == 3) +#define flash_EBIU_AMBCTL0_TT B0TT_3 +#endif +#if (flash_EBIU_AMBCTL_TT == 2) +#define flash_EBIU_AMBCTL0_TT B0TT_2 +#endif +#if (flash_EBIU_AMBCTL_TT < 2) +#define flash_EBIU_AMBCTL0_TT B0TT_1 +#endif + +#if (flash_EBIU_AMBCTL_ST > 3) +#define flash_EBIU_AMBCTL0_ST B0ST_4 +#endif +#if (flash_EBIU_AMBCTL_ST == 3) +#define flash_EBIU_AMBCTL0_ST B0ST_3 +#endif +#if (flash_EBIU_AMBCTL_ST == 2) +#define flash_EBIU_AMBCTL0_ST B0ST_2 +#endif +#if (flash_EBIU_AMBCTL_ST < 2) +#define flash_EBIU_AMBCTL0_ST B0ST_1 +#endif + +#if (flash_EBIU_AMBCTL_HT > 2) +#define flash_EBIU_AMBCTL0_HT B0HT_3 +#endif +#if (flash_EBIU_AMBCTL_HT == 2) +#define flash_EBIU_AMBCTL0_HT B0HT_2 +#endif +#if (flash_EBIU_AMBCTL_HT == 1) +#define flash_EBIU_AMBCTL0_HT B0HT_1 +#endif +#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0) +#define flash_EBIU_AMBCTL0_HT B0HT_0 +#endif +#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0) +#define flash_EBIU_AMBCTL0_HT B0HT_1 +#endif + +#if (flash_EBIU_AMBCTL_WAT > 14) +#define flash_EBIU_AMBCTL0_WAT B0WAT_15 +#endif +#if (flash_EBIU_AMBCTL_WAT == 14) +#define flash_EBIU_AMBCTL0_WAT B0WAT_14 +#endif +#if (flash_EBIU_AMBCTL_WAT == 13) +#define flash_EBIU_AMBCTL0_WAT B0WAT_13 +#endif +#if (flash_EBIU_AMBCTL_WAT == 12) +#define flash_EBIU_AMBCTL0_WAT B0WAT_12 +#endif +#if (flash_EBIU_AMBCTL_WAT == 11) +#define flash_EBIU_AMBCTL0_WAT B0WAT_11 +#endif +#if (flash_EBIU_AMBCTL_WAT == 10) +#define flash_EBIU_AMBCTL0_WAT B0WAT_10 +#endif +#if (flash_EBIU_AMBCTL_WAT == 9) +#define flash_EBIU_AMBCTL0_WAT B0WAT_9 +#endif +#if (flash_EBIU_AMBCTL_WAT == 8) +#define flash_EBIU_AMBCTL0_WAT B0WAT_8 +#endif +#if (flash_EBIU_AMBCTL_WAT == 7) +#define flash_EBIU_AMBCTL0_WAT B0WAT_7 +#endif +#if (flash_EBIU_AMBCTL_WAT == 6) +#define flash_EBIU_AMBCTL0_WAT B0WAT_6 +#endif +#if (flash_EBIU_AMBCTL_WAT == 5) +#define flash_EBIU_AMBCTL0_WAT B0WAT_5 +#endif +#if (flash_EBIU_AMBCTL_WAT == 4) +#define flash_EBIU_AMBCTL0_WAT B0WAT_4 +#endif +#if (flash_EBIU_AMBCTL_WAT == 3) +#define flash_EBIU_AMBCTL0_WAT B0WAT_3 +#endif +#if (flash_EBIU_AMBCTL_WAT == 2) +#define flash_EBIU_AMBCTL0_WAT B0WAT_2 +#endif +#if (flash_EBIU_AMBCTL_WAT == 1) +#define flash_EBIU_AMBCTL0_WAT B0WAT_1 +#endif + +#if (flash_EBIU_AMBCTL_RAT > 14) +#define flash_EBIU_AMBCTL0_RAT B0RAT_15 +#endif +#if (flash_EBIU_AMBCTL_RAT == 14) +#define flash_EBIU_AMBCTL0_RAT B0RAT_14 +#endif +#if (flash_EBIU_AMBCTL_RAT == 13) +#define flash_EBIU_AMBCTL0_RAT B0RAT_13 +#endif +#if (flash_EBIU_AMBCTL_RAT == 12) +#define flash_EBIU_AMBCTL0_RAT B0RAT_12 +#endif +#if (flash_EBIU_AMBCTL_RAT == 11) +#define flash_EBIU_AMBCTL0_RAT B0RAT_11 +#endif +#if (flash_EBIU_AMBCTL_RAT == 10) +#define flash_EBIU_AMBCTL0_RAT B0RAT_10 +#endif +#if (flash_EBIU_AMBCTL_RAT == 9) +#define flash_EBIU_AMBCTL0_RAT B0RAT_9 +#endif +#if (flash_EBIU_AMBCTL_RAT == 8) +#define flash_EBIU_AMBCTL0_RAT B0RAT_8 +#endif +#if (flash_EBIU_AMBCTL_RAT == 7) +#define flash_EBIU_AMBCTL0_RAT B0RAT_7 +#endif +#if (flash_EBIU_AMBCTL_RAT == 6) +#define flash_EBIU_AMBCTL0_RAT B0RAT_6 +#endif +#if (flash_EBIU_AMBCTL_RAT == 5) +#define flash_EBIU_AMBCTL0_RAT B0RAT_5 +#endif +#if (flash_EBIU_AMBCTL_RAT == 4) +#define flash_EBIU_AMBCTL0_RAT B0RAT_4 +#endif +#if (flash_EBIU_AMBCTL_RAT == 3) +#define flash_EBIU_AMBCTL0_RAT B0RAT_3 +#endif +#if (flash_EBIU_AMBCTL_RAT == 2) +#define flash_EBIU_AMBCTL0_RAT B0RAT_2 +#endif +#if (flash_EBIU_AMBCTL_RAT == 1) +#define flash_EBIU_AMBCTL0_RAT B0RAT_1 +#endif + +#define flash_EBIU_AMBCTL0 \ + (flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \ + flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN) diff --git a/include/asm-blackfin/mach-bf527/mem_map.h b/include/asm-blackfin/mach-bf527/mem_map.h new file mode 100644 index 00000000000..c5aa20102b2 --- /dev/null +++ b/include/asm-blackfin/mach-bf527/mem_map.h @@ -0,0 +1,98 @@ +/* + * file: include/asm-blackfin/mach-bf527/mem_map.h + * based on: include/asm-blackfin/mach-bf537/mem_map.h + * author: Michael Hennerich (michael.hennerich@analog.com) + * + * created: + * description: + * Memory MAP Common header file for blackfin BF527/5/2 of processors. + * rev: + * + * modified: + * + * bugs: enter bugs at http://blackfin.uclinux.org/ + * + * this program is free software; you can redistribute it and/or modify + * it under the terms of the gnu general public license as published by + * the free software foundation; either version 2, or (at your option) + * any later version. + * + * this program is distributed in the hope that it will be useful, + * but without any warranty; without even the implied warranty of + * merchantability or fitness for a particular purpose. see the + * gnu general public license for more details. + * + * you should have received a copy of the gnu general public license + * along with this program; see the file copying. + * if not, write to the free software foundation, + * 59 temple place - suite 330, boston, ma 02111-1307, usa. + */ + +#ifndef _MEM_MAP_527_H_ +#define _MEM_MAP_527_H_ + +#define COREMMR_BASE 0xFFE00000 /* Core MMRs */ +#define SYSMMR_BASE 0xFFC00000 /* System MMRs */ + +/* Async Memory Banks */ +#define ASYNC_BANK3_BASE 0x20300000 /* Async Bank 3 */ +#define ASYNC_BANK3_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK2_BASE 0x20200000 /* Async Bank 2 */ +#define ASYNC_BANK2_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK1_BASE 0x20100000 /* Async Bank 1 */ +#define ASYNC_BANK1_SIZE 0x00100000 /* 1M */ +#define ASYNC_BANK0_BASE 0x20000000 /* Async Bank 0 */ +#define ASYNC_BANK0_SIZE 0x00100000 /* 1M */ + +/* Boot ROM Memory */ + +#define BOOT_ROM_START 0xEF000000 + +/* Level 1 Memory */ + +/* Memory Map for ADSP-BF527 ADSP-BF525 ADSP-BF522 processors */ + +#ifdef CONFIG_BFIN_ICACHE +#define BFIN_ICACHESIZE (16*1024) +#else +#define BFIN_ICACHESIZE (0*1024) +#endif + +#define L1_CODE_START 0xFFA00000 +#define L1_DATA_A_START 0xFF800000 +#define L1_DATA_B_START 0xFF900000 + +#define L1_CODE_LENGTH 0xC000 + +#ifdef CONFIG_BFIN_DCACHE + +#ifdef CONFIG_BFIN_DCACHE_BANKA +#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH (0x8000 - 0x4000) +#define L1_DATA_B_LENGTH 0x8000 +#define BFIN_DCACHESIZE (16*1024) +#define BFIN_DSUPBANKS 1 +#else +#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH (0x8000 - 0x4000) +#define L1_DATA_B_LENGTH (0x8000 - 0x4000) +#define BFIN_DCACHESIZE (32*1024) +#define BFIN_DSUPBANKS 2 +#endif + +#else +#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0) +#define L1_DATA_A_LENGTH 0x8000 +#define L1_DATA_B_LENGTH 0x8000 +#define BFIN_DCACHESIZE (0*1024) +#define BFIN_DSUPBANKS 0 +#endif /*CONFIG_BFIN_DCACHE */ + +/* Scratch Pad Memory */ + +#if defined(CONFIG_BF527) || defined(CONFIG_BF536) || defined(CONFIG_BF534) +#define L1_SCRATCH_START 0xFFB00000 +#define L1_SCRATCH_LENGTH 0x1000 +#endif + +#endif /* _MEM_MAP_527_H_ */ diff --git a/include/asm-blackfin/mach-bf527/portmux.h b/include/asm-blackfin/mach-bf527/portmux.h new file mode 100644 index 00000000000..dcf001adc63 --- /dev/null +++ b/include/asm-blackfin/mach-bf527/portmux.h @@ -0,0 +1,205 @@ +#ifndef _MACH_PORTMUX_H_ +#define _MACH_PORTMUX_H_ + +#define P_PPI0_D0 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(0)) +#define P_PPI0_D1 (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(0)) +#define P_PPI0_D2 (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(0)) +#define P_PPI0_D3 (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(0)) +#define P_PPI0_D4 (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(0)) +#define P_PPI0_D5 (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(0)) +#define P_PPI0_D6 (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(0)) +#define P_PPI0_D7 (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(0)) +#define P_PPI0_D8 (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(0)) +#define P_PPI0_D9 (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(0)) +#define P_PPI0_D10 (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(0)) +#define P_PPI0_D11 (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(0)) +#define P_PPI0_D12 (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(0)) +#define P_PPI0_D13 (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(0)) +#define P_PPI0_D14 (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(0)) +#define P_PPI0_D15 (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(0)) + +#if defined(CONFIG_BF527_SPORT0_PORTF) +#define P_SPORT0_DRPRI (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1)) +#define P_SPORT0_RFS (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1)) +#define P_SPORT0_RSCLK (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1)) +#define P_SPORT0_DTPRI (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1)) +#define P_SPORT0_TFS (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1)) +#define P_SPORT0_TSCLK (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1)) +#define P_SPORT0_DTSEC (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1)) +#define P_SPORT0_DRSEC (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1)) +#elif defined(CONFIG_BF527_SPORT0_PORTG) +#define P_SPORT0_DTPRI (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(0)) +#define P_SPORT0_DRSEC (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1)) +#define P_SPORT0_DTSEC (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1)) +#define P_SPORT0_DRPRI (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1)) +#define P_SPORT0_RFS (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(1)) +#define P_SPORT0_RSCLK (P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(1)) +#if defined(CONFIG_BF527_SPORT0_TSCLK_PG10) +#define P_SPORT0_TSCLK (P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(1)) +#elif defined(CONFIG_BF527_SPORT0_TSCLK_PG14) +#define P_SPORT0_TSCLK (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(0)) +#endif +#define P_SPORT0_TFS (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(0)) +#endif + +#define P_SPORT1_DRPRI (P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1)) +#define P_SPORT1_RSCLK (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1)) +#define P_SPORT1_RFS (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1)) +#define P_SPORT1_TFS (P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1)) +#define P_SPORT1_DTPRI (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1)) +#define P_SPORT1_TSCLK (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1)) +#define P_SPORT1_DTSEC (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1)) +#define P_SPORT1_DRSEC (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1)) + +#define P_SPI0_SSEL6 (P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(2)) +#define P_SPI0_SSEL7 (P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(2)) + +#define P_SPI0_SSEL2 (P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2)) +#define P_SPI0_SSEL3 (P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2)) + +#if defined(CONFIG_BF527_UART1_PORTF) +#define P_UART1_TX (P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2)) +#define P_UART1_RX (P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2)) +#elif defined(CONFIG_BF527_UART1_PORTG) +#define P_UART1_TX (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(1)) +#define P_UART1_RX (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(1)) +#endif + +#define P_HWAIT (P_DONTCARE) + +#define P_SPI0_SS (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0)) +#define P_SPI0_SSEL1 (P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2)) +#define P_SPI0_SCK (P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2)) +#define P_SPI0_MISO (P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(2)) +#define P_SPI0_MOSI (P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(2)) +#define P_TMR1 (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0)) +#define P_PPI0_FS2 (P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0)) +#define P_TMR3 (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(0)) +#define P_TMR4 (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(0)) +#define P_TMR5 (P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(0)) +#define P_TMR6 (P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(0)) +/* #define P_TMR7 (P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(0)) */ +#define P_DMAR1 (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(0)) +#define P_DMAR0 (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(0)) +#define P_TMR2 (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1)) +#define P_TMR7 (P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(1)) +#define P_MDC (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(1)) +#define P_RMII0_MDINT (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1)) +#define P_MII0_PHYINT (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1)) + +#define P_PPI0_FS3 (P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(2)) +#define P_UART0_TX (P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(2)) +#define P_UART0_RX (P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(2)) + +#define P_HOST_WR (P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(2)) +#define P_HOST_ACK (P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(2)) +#define P_HOST_ADDR (P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(2)) +#define P_HOST_RD (P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2)) +#define P_HOST_CE (P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(2)) + +#if defined(CONFIG_BF527_NAND_D_PORTF) +#define P_NAND_D0 (P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(2)) +#define P_NAND_D1 (P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2)) +#define P_NAND_D2 (P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2)) +#define P_NAND_D3 (P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2)) +#define P_NAND_D4 (P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2)) +#define P_NAND_D5 (P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2)) +#define P_NAND_D6 (P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2)) +#define P_NAND_D7 (P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2)) +#elif defined(CONFIG_BF527_NAND_D_PORTH) +#define P_NAND_D0 (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(0)) +#define P_NAND_D1 (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(0)) +#define P_NAND_D2 (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(0)) +#define P_NAND_D3 (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(0)) +#define P_NAND_D4 (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(0)) +#define P_NAND_D5 (P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(0)) +#define P_NAND_D6 (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(0)) +#define P_NAND_D7 (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(0)) +#endif + +#define P_SPI0_SSEL4 (P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(0)) +#define P_SPI0_SSEL5 (P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(0)) +#define P_NAND_CE (P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(0)) +#define P_NAND_WE (P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(0)) +#define P_NAND_RE (P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(0)) +#define P_NAND_RB (P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(0)) +#define P_NAND_CLE (P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(0)) +#define P_NAND_ALE (P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(0)) + +#define P_HOST_D0 (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(2)) +#define P_HOST_D1 (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(2)) +#define P_HOST_D2 (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(2)) +#define P_HOST_D3 (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(2)) +#define P_HOST_D4 (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(2)) +#define P_HOST_D5 (P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(2)) +#define P_HOST_D6 (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(2)) +#define P_HOST_D7 (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(2)) +#define P_HOST_D8 (P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(2)) +#define P_HOST_D9 (P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(2)) +#define P_HOST_D10 (P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(2)) +#define P_HOST_D11 (P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(2)) +#define P_HOST_D12 (P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(2)) +#define P_HOST_D13 (P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(2)) +#define P_HOST_D14 (P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(2)) +#define P_HOST_D15 (P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(2)) + +#define P_MII0_ETxD0 (P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(1)) +#define P_MII0_ETxD1 (P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(1)) +#define P_MII0_ETxD2 (P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(1)) +#define P_MII0_ETxD3 (P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(1)) +#define P_MII0_ETxEN (P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(1)) +#define P_MII0_TxCLK (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1)) +#define P_MII0_COL (P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(1)) +#define P_MII0_ERxD0 (P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(1)) +#define P_MII0_ERxD1 (P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(1)) +#define P_MII0_ERxD2 (P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(1)) +#define P_MII0_ERxD3 (P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(1)) +#define P_MII0_ERxDV (P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(1)) +#define P_MII0_ERxCLK (P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(1)) +#define P_MII0_ERxER (P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(1)) +#define P_MII0_CRS (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1)) +#define P_RMII0_REF_CLK (P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1)) +#define P_RMII0_CRS_DV (P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1)) +#define P_MDIO (P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(1)) + +#define P_TWI0_SCL (P_DONTCARE) +#define P_TWI0_SDA (P_DONTCARE) +#define P_PPI0_FS1 (P_DONTCARE) +#define P_TMR0 (P_DONTCARE) +#define P_TMRCLK (P_DONTCARE) +#define P_PPI0_CLK (P_DONTCARE) + +#define P_MII0 {\ + P_MII0_ETxD0, \ + P_MII0_ETxD1, \ + P_MII0_ETxD2, \ + P_MII0_ETxD3, \ + P_MII0_ETxEN, \ + P_MII0_TxCLK, \ + P_MII0_PHYINT, \ + P_MII0_COL, \ + P_MII0_ERxD0, \ + P_MII0_ERxD1, \ + P_MII0_ERxD2, \ + P_MII0_ERxD3, \ + P_MII0_ERxDV, \ + P_MII0_ERxCLK, \ + P_MII0_ERxER, \ + P_MII0_CRS, \ + P_MDC, \ + P_MDIO, 0} + +#define P_RMII0 {\ + P_MII0_ETxD0, \ + P_MII0_ETxD1, \ + P_MII0_ETxEN, \ + P_MII0_ERxD0, \ + P_MII0_ERxD1, \ + P_MII0_ERxER, \ + P_RMII0_REF_CLK, \ + P_RMII0_MDINT, \ + P_RMII0_CRS_DV, \ + P_MDC, \ + P_MDIO, 0} + +#endif /* _MACH_PORTMUX_H_ */ -- 2.41.1