This fixes some instances where we were continuing after calling
ext3_error. ext3_error calls panic only if errors=panic mount option is
set. So we need to make sure we return correctly after ext3_error call
When a new block bitmap is read from disk in read_block_bitmap() there are a
few bits that should ALWAYS be set. In particular, the blocks given
corresponding to block bitmap, inode bitmap and inode tables. Validate the
block bitmap against these blocks.
When a new block bitmap is read from disk in read_block_bitmap() there are a
few bits that should ALWAYS be set. In particular, the blocks given
corresponding to block bitmap, inode bitmap and inode tables. Validate the
block bitmap against these blocks.
Bjorn Helgaas [Wed, 6 Feb 2008 09:40:08 +0000 (01:40 -0800)]
PNP: disable Supermicro H8DCE motherboard resources that overlap SATA BARs
Some Supermicro BIOSes describe a SATA PCI BAR as a motherboard resource.
The PNP system driver claims motherboard resources, and this prevents the
sata_nv driver from requesting it later.
This patch disables the PNP0C01/PNP0C02 resources so they won't be claimed
by the PNP system driver, so they'll available for sata_nv.
This fixes the bugs below, where sata_nv detects only two out of four SATA
drives. The signature includes dmesg lines similar to these:
pnp: 00:09: iomem range 0xdfefc000-0xdfefcfff has been reserved
pnp: 00:09: iomem range 0xdfefd000-0xdfefd3ff has been reserved
pnp: 00:09: iomem range 0xdfefe000-0xdfefe3ff has been reserved
PCI: Unable to reserve mem region #6:1000@dfefd000 for device 0000:80:07.0
sata_nv: probe of 0000:80:07.0 failed with error -16
PCI: Unable to reserve mem region #6:1000@dfefe000 for device 0000:80:08.0
sata_nv: probe of 0000:80:08.0 failed with error -16
Rene Herman [Wed, 6 Feb 2008 09:40:05 +0000 (01:40 -0800)]
PNP: do not test PNP_DRIVER_RES_DO_NOT_CHANGE on suspend/resume
The PNP_DRIVER_RES_DO_NOT_CHANGE flag is meant to signify that the PNP core
should not change resources for the device -- not that it shouldn't
disable/enable the device on suspend/resume.
ALSA ISAPnP drivers set PNP_DRIVER_RES_DO_NOT_CHANAGE (0x0001) through
setting PNP_DRIVER_RES_DISABLE (0x0003). The latter including the former
may in itself be considered rather unexpected but doesn't change that
suspend/resume wouldn't seem to have any business testing the flag.
As reported by Ondrej Zary for snd-cs4236, ALSA driven ISAPnP cards don't
survive swsusp hibernation with the resume skipping setting the resources
due to testing the flag -- the same test in the suspend path isn't enough
to keep hibernation from disabling the card it seems.
These tests were added (in 2005) by Piere Ossman in commit 68094e3251a664ee1389fcf179497237cbf78331, "alsa: Improved PnP suspend
support" who doesn't remember why. This deletes them.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Tested-by: Ondrej Zary <linux@rainbow-software.org> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Pierre Ossman <drzeus@drzeus.cx> Cc: Adam Belay <ambx1@neo.rr.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pnp: declare PNP option parsing functions as __init
There are three kind of parse functions provided by PNP acpi/bios:
- get current resources
- set resources
- get possible resources
The first two may be needed later at runtime.
The possible resource settings should never change dynamically.
And even if this would make any sense (I doubt it), the current implementation
only parses possible resource settings at early init time:
-> declare all the option parsing __init
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Thomas Renninger <trenn@suse.de> Acked-By: Rene Herman <rene.herman@gmail.com> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:40:00 +0000 (01:40 -0800)]
md: fix an occasional deadlock in raid5
raid5's 'make_request' function calls generic_make_request on underlying
devices and if we run out of stripe heads, it could end up waiting for one of
those requests to complete. This is bad as recursive calls to
generic_make_request go on a queue and are not even attempted until
make_request completes.
So: don't make any generic_make_request calls in raid5 make_request until all
waiting has been done. We do this by simply setting STRIPE_HANDLE instead of
calling handle_stripe().
If we need more stripe_heads, raid5d will get called to process the pending
stripe_heads which will call generic_make_request from a
This change by itself causes a performance hit. So add a change so that
raid5_activate_delayed is only called at unplug time, never in raid5. This
seems to bring back the performance numbers. Calling it in raid5d was
sometimes too soon...
Neil said:
How about we queue it for 2.6.25-rc1 and then about when -rc2 comes out,
we queue it for 2.6.24.y?
Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Tested-by: dean gaudet <dean@arctic.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:59 +0000 (01:39 -0800)]
md: change ITERATE_RDEV_GENERIC to rdev_for_each_list, and remove ITERATE_RDEV_PENDING.
Finish ITERATE_ to for_each conversion.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:59 +0000 (01:39 -0800)]
md: change ITERATE_RDEV to rdev_for_each
As this is more in line with common practice in the kernel. Also swap the
args around to be more like list_for_each.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:58 +0000 (01:39 -0800)]
md: change INTERATE_MDDEV to for_each_mddev
As this is more consistent with kernel style.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:57 +0000 (01:39 -0800)]
md: change a few 'int' to 'size_t' in md
As suggested by Andrew Morton.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:56 +0000 (01:39 -0800)]
md: fix use-after-free bug when dropping an rdev from an md array
Due to possible deadlock issues we need to use a schedule work to kobject_del
an 'rdev' object from a different thread.
A recent change means that kobject_add no longer gets a refernce, and
kobject_del doesn't put a reference. Consequently, we need to explicitly hold
a reference to ensure that the last reference isn't dropped before the
scheduled work get a chance to call kobject_del.
Also, rename delayed_delete to md_delayed_delete to that it is more obvious in
a stack trace which code is to blame.
Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:55 +0000 (01:39 -0800)]
md: allow an md array to appear with 0 drives if it has external metadata
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:55 +0000 (01:39 -0800)]
md: lock address when changing attributes of component devices
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:54 +0000 (01:39 -0800)]
md: allow devices to be shared between md arrays
Currently, a given device is "claimed" by a particular array so that it cannot
be used by other arrays.
This is not ideal for DDF and other metadata schemes which have their own
partitioning concept.
So for externally managed metadata, just claim the device for md in general,
require that "offset" and "size" are set properly for each device, and make
sure that if a device is included in different arrays then the active sections
do not overlap.
This involves adding another flag to the rdev which makes it awkward to set
"->flags = 0" to clear certain flags. So now clear flags explicitly by name
when we want to clear things.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:53 +0000 (01:39 -0800)]
md: set and test the ->persistent flag for md devices more consistently
If you try to start an array for which the number of raid disks is listed as
zero, md will currently try to read metadata off any devices that have been
given. This was done because the value of raid_disks is used to signal
whether array details have been provided by userspace (raid_disks > 0) or must
be read from the devices (raid_disks == 0).
However for an array without persistent metadata (or with externally managed
metadata) this is the wrong thing to do. So we add a test in do_md_run to
give an error if raid_disks is zero for non-persistent arrays.
This requires that mddev->persistent is set corrently at this point, which it
currently isn't for in-kernel autodetected arrays.
So set ->persistent for autodetect arrays, and remove the settign in
super_*_validate which is now redundant.
Also clear ->persistent when stopping an array so it is consistently zero when
starting an array.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:52 +0000 (01:39 -0800)]
md: allow a maximum extent to be set for resyncing
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.
Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:51 +0000 (01:39 -0800)]
md: give userspace control over removing failed devices when external metdata in use
When a device fails, we must not allow an further writes to the array until
the device failure has been recorded in array metadata. When metadata is
managed externally, this requires some synchronisation...
Allow/require userspace to explicitly remove failed devices from active
service in the array by writing 'none' to the 'slot' attribute. If this
reduces the number of failed devices to 0, the write block will automatically
be lowered.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:51 +0000 (01:39 -0800)]
md: support 'external' metadata for md arrays
- Add a state flag 'external' to indicate that the metadata is managed
externally (by user-space) so important changes need to be
left of user-space to handle.
Alternates are non-persistant ('none') where there is no stable metadata -
after the array is stopped there is no record of it's status - and
internal which can be version 0.90 or version 1.x
These are selected by writing to the 'metadata' attribute.
- move the updating of superblocks (sync_sbs) to after we have checked if
there are any superblocks or not.
- New array state 'write_pending'. This means that the metadata records
the array as 'clean', but a write has been requested, so the metadata has
to be updated to record a 'dirty' array before the write can continue.
This change is reported to md by writing 'active' to the array_state
attribute.
- tidy up marking of sb_dirty:
- don't set sb_dirty when resync finishes as md_check_recovery
calls md_update_sb when the sync thread finishes anyway.
- Don't set sb_dirty in multipath_run as the array might not be dirty.
- don't mark superblock dirty when switching to 'clean' if there
is no internal superblock (if external, userspace can choose to
update the superblock whenever it chooses to).
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Wed, 6 Feb 2008 09:39:50 +0000 (01:39 -0800)]
md: Update md bitmap during resync.
Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync. Rather the entire bitmap is updated
when the resync completes.
This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.
However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap. Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.
[snitzer@gmail.com: export bitmap_cond_end_sync] Signed-off-by: Neil Brown <neilb@suse.de> Cc: "Mike Snitzer" <snitzer@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 6 Feb 2008 09:39:48 +0000 (01:39 -0800)]
md: raid6: clean up the style of raid6test/test.c
Clean up the coding style in raid6test/test.c. Break it apart into
subfunctions to make the code more readable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 6 Feb 2008 09:39:48 +0000 (01:39 -0800)]
md: raid6: Fix mktable.c
Make both mktables.c and its output CodingStyle compliant. Update the
copyright notice.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oliver Pinter [Wed, 6 Feb 2008 09:39:47 +0000 (01:39 -0800)]
coding style cleanups for drivers/md/mktables.c
Signed-off-by: Oliver Pinter <oliver.pntr@gmail.com> Cc: Neil Brown <neilb@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Pfaff [Wed, 6 Feb 2008 09:39:45 +0000 (01:39 -0800)]
fbcon: fix color generation for monochrome framebuffer
The current attr_fgcol_ec / attr_bgcol_ec macros do a simple shift of bits
to get the color from vc_video_erase_char. For a monochrome display
however the attribute does not contain any color, only attribute bits.
Furthermore the reverse bit is lost because it is shifted out, the
resulting color is always 0.
This can bee seen on a monochrome console either directly or by setting it
to inverse mode via "setterm -inversescreen on" . Text is written with
correct color, fb_fillrects from a bit_clear / bit_clear_margins will get
wrong colors.
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Wed, 6 Feb 2008 09:39:44 +0000 (01:39 -0800)]
FB/S3C2410: check default_display parameter passed in platform data
Ensure that the default display parameter passed in via the
device's platform data is valid. It turns out when mach-bast.c
was updated, the default_display was set outside of the display
array bounds, causing a panic on startup.
If the default_display is bigger than num_displays, then generate
an error and refuse to initialise the driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Vincent Sanders <vince@simtec.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Wed, 6 Feb 2008 09:39:38 +0000 (01:39 -0800)]
FB/SM501: ensure console suspended before saving state
Move the console suspend to before we save the state of
the framebuffer to ensure that it does not try and change
the fb state again once we have copied it out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Vincent Sanders <vince@simtec.co.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cleanup sweep:
- Kill ps3fb_priv.xdr_ea and ps3fb_priv.xdr_size, use info->screen_base and
info->fix.smem_len instead.
- Kill superfluous assignments to info->fix.smem_start, info->fix.smem_len,
and info->screen_base in ps3fb_set_par(). Their values never change.
- Add sparse annotations to casts to kill address space warnings
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorganize modedb handling:
- Reorder the video modes in ps3fb_modedb, for easier indexing using
PS3AV_MODE_* numbers,
- Introduce ps3fb_native_vmode(), to convert from native (PS3AV_MODE_*) mode
numbers to struct fb_videomode *,
- Rename and move ps3fb_default_mode() to ps3fb_vmode().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 6 Feb 2008 09:39:26 +0000 (01:39 -0800)]
atmel_lcdfb: backlight control
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Russell King <rmk@arm.linux.org.uk> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Wed, 6 Feb 2008 09:39:25 +0000 (01:39 -0800)]
sm501fb: clear framebuffer memory and palette
Avoid displaying garbage on unused framebuffers. For most users a single
framebuffer is used together with fbcon. sm501fb supports two framebuffers
where one often is assigned to fbcon and the other one is left unused during
the boot.
The problem here is that framebuffers not in use by fbcon happen to display
garbage. This can easily be solved by making sure that framebuffer memory and
palette ram are cleared.
The problem can be observed by using looking at the panel output (fb1) after
booting the kernel with fbcon on crt (fb0). This is the default
configuration. It's also possible to watch the garbage on the crt framebuffer
by passing "fbcon=map:1" on the kernel cmdline. This will assign fbcon to the
panel (fb1) and leave the crt (fb0) unused.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Wed, 6 Feb 2008 09:39:24 +0000 (01:39 -0800)]
sm501fb: control panel pin usage with platform data flags
This patch makes it possible to control panel pins usage with flags passed
from the platform data. Without this patch the sm501fb driver always controls
the VBIASEN and FPEN pins. The polarity and use of these pins are very
platform specific, so this patch introduces the flags
SM501FB_FLAG_PANEL_USE_VBIASEN and SM501FB_FLAG_PANEL_USE_FPEN which enable
the use of these pins.
This patch is needed to support the a Sharp LQ104V1DG21 lcd panel on SuperH
platforms such as R2D-1 and R2D-PLUS boards. Letting the sm501fb driver
control the FPEN and VBIASEN pins like today just results in lcd panel
flicker.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Paul Mundt <lethal@linux-sh.org> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Wed, 6 Feb 2008 09:39:23 +0000 (01:39 -0800)]
drivers/video: add missing pci_dev_get
pci_get_device does a pci_dev_get, so pci_dev_put needs to be called in an
error case
The problem was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@exists@
type T1,T2;
identifier E;
statement S,S1;
expression x1,x2,x3;
expression test;
int ret != 0;
@@
struct pci_dev *E;
...
(
E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...);
if (E == NULL) S
|
if ((E = \(pci_get_slot\|pci_get_device\|pci_get_bus_and_slot\)(...)) == NULL) S
)
... when != pci_dev_put(...,(T1)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
(
if (E == NULL) S1
|
if (test)
+ {
(
+ pci_dev_put(E);
return;
|
+ pci_dev_put(E);
return ret;
)
+ }
|
if (test) {
... when != pci_dev_put(...,(T2)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
+ pci_dev_put(E);
return;
|
+ pci_dev_put(E);
return ret;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Cc: "David S. Miller" <davem@davemloft.net> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 6 Feb 2008 09:39:22 +0000 (01:39 -0800)]
uvesafb: small cleanups
Some cleanups in uvesafb:
- The custom module_param() get/set functions don't need to be inlined
since it is referred to via a pointer in a struct.
- don't end a #define with a ';'
- remove one of the single quote marks in "''ypan'"
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Michal Januszewski <spock@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 6 Feb 2008 09:39:19 +0000 (01:39 -0800)]
tdfxfb: fix section mismatch warnings
tdfxfb_setup() can be __init. This fixes the modpost section mismatch
warnings:
WARNING: vmlinux.o(.text+0x4cff9b): Section mismatch: reference to .init.data:mode_option (between 'tdfxfb_setup' and 'getclkMHz')
WARNING: vmlinux.o(.text+0x4cffa8): Section mismatch: reference to .init.data: (between 'tdfxfb_setup' and 'getclkMHz')
[krzysztof.h1@poczta.fm: use __init, not __devinit] Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Wed, 6 Feb 2008 09:39:18 +0000 (01:39 -0800)]
fb: nvidiafb: Try harder at initial mode setting.
The current nvidiafb_check_var() simply bails out if the selected mode is
out of range of the panel dimensions. A good question would be why the
bogus mode is being selected in the first place -- the panel dimensions
that are read back are certainly bogus, but alas, I have no idea where to
even begin looking at the i2c/EDID/DDC mess:
nvidiafb: Device ID: 10de0165
nvidiafb: CRTC0 analog not found
nvidiafb: CRTC1 analog not found
nvidiafb: EDID found from BUS1
nvidiafb: CRTC 0 is currently programmed for DFP
nvidiafb: Using DFP on CRTC 0
nvidiafb: Panel size is 1280 x 1024
nvidiafb: Panel is TMDS
nvidiafb: unable to setup MTRR
nvidiafb: Flat panel dithering disabled
nvidiafb: PCI nVidia NV16 framebuffer (64MB @ 0xC0000000)
I've not tried fiddling with these options, as I haven't the vaguest idea
what I should be looking at.
As a workaround, simply groveling for a new mode based on the probed
dimensions seems to work ok. While it would be nice to debug this further
and sort out why the panel information is bogus, I think it's still worth
retrying the mode based on the panel information at hand as a last-ditch
effort, rather than simply bailing out completely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Cc: Antonino A. Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Wed, 6 Feb 2008 09:39:15 +0000 (01:39 -0800)]
drivers/video/pm3fb.c section fix
WARNING: vmlinux.o(.text+0x46e456): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e45c): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e49b): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4a0): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4bc): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e4c2): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e5c1): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
WARNING: vmlinux.o(.text+0x46e5c7): Section mismatch: reference to .init.data: (between 'pm3fb_size_memory' and 'update_crtc2')
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting a display timing parameter too high or too low may cause it to
wrap around and thus become completely wrong. Validate the timings in
atmel_lcdfb_check_var() and saturate to the highest or lowest possible
value if necessary.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This third part of an extension to support more pca953x chips updates the
logic to handle the smaller register widths used by the 4-bit and 8-bit parts,
and to use the chip type to determine how many GPIOs it provides.
As long as we don't support interrupt and reset capabilities, those size
issues are the only software-visible differences between these parts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This second part of an extension to support more pca953x chips renames the C
and Kconfig symbols. All affected files were updated by sed, except for a
couple of obvious exceptions. It also updates the Kconfig helptext.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ville Syrjala [Wed, 6 Feb 2008 09:39:01 +0000 (01:39 -0800)]
w1-gpio: add GPIO w1 bus master driver
Add a GPIO 1-wire bus master driver. The driver used the GPIO API to
control the wire and the GPIO pin can be specified using platform data
similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.
Signed-off-by: Ville Syrjala <syrjala@sci.fi> Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Don't force use of RTT0 and GPBR0. Either resource may need
to be used for other purposes (like NO_HZ support).
- Update "AT91RM9200 RTC" Kconfig to allow it on SAM9RL chips
(it has both RTT and RTC).
Driver binding uses bus_find_device() to avoid needing any kind of "timer
library" code when there's more than one RTT module. (This timer can be used
as an RTC, to support NO_HZ operation, or potentially for other stuff. The
choice is a per-system policy.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Michel Benoit <murpme@gmail.com> Cc: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 6 Feb 2008 09:38:57 +0000 (01:38 -0800)]
rtc: remove more dev->power.power_state usage
Remove some more references to dev->power.power_state. That field is overdue
for removal, but we can't do that while it's still referenced in the kernel.
The only reason to update it was to make the /sys/devices/.../power/state
files (now removed) work better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
frederic Rodo [Wed, 6 Feb 2008 09:38:55 +0000 (01:38 -0800)]
rtc ds1307: ds_1340 change init
For DS140, clear the oscillator fault flag as needed.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
[ And remove some "sparse" warnings. ] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bernhard Walle [Wed, 6 Feb 2008 09:38:52 +0000 (01:38 -0800)]
rtc: add HPET RTC emulation to RTC_DRV_CMOS
That patch adds the RTC emulation of the HPET timer to the new RTC_DRV_CMOS.
The old drivers/char/rtc.ko driver had that functionality and it's important
on new systems.
[akpm@linux-foundation.org: unbreak alpha build] Signed-off-by: Bernhard Walle <bwalle@suse.de> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andi Kleen <ak@suse.de> Cc: john stultz <johnstul@us.ibm.com> Cc: Robert Picco <Robert.Picco@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 6 Feb 2008 09:38:45 +0000 (01:38 -0800)]
rtc-cmos alarm acts as oneshot
Start making the rtc-cmos alarm act more like a oneshot alarm by disabling
that alarm after its IRQ fires. (ACPI hooks are also needed.)
The Linux RTC framework has previously been a bit vague in this area, but
any other behavior is problematic and not very portable. RTCs with full
YYYY-MM-DD HH:MM[:SS] alarms won't have a problem here. Only ones with
partial match criteria, with the most visible example being the PC RTC, get
confused. (Because the criteria will match repeatedly.)
Update comments relating to that oneshot behavior and timezone handling.
(Timezones are another issue that's mostly visible with rtc-cmos. That's
because PCs often dual-boot MS-Windows, which likes its RTC to match local
wall-clock time instead of UTC.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Wed, 6 Feb 2008 09:38:44 +0000 (01:38 -0800)]
rtc: ds1302 rtc support
This adds a basic ds1302 RTC driver, which is basically a cleanup and move
of the in-tree SH SecureEdge5410 code (which is currently located in
arch/sh/board/snapgear/rtc.c) to drivers/rtc.
This aims to be a building block that the M32R and CRIS code can be worked
on top of, so we can get rid of drivers/char/ds1302.c and
arch/cris/arch-v10/drivers/ds1302.c respectively, though more work is
needed for this.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Wed, 6 Feb 2008 09:38:43 +0000 (01:38 -0800)]
rtc-cmos: export nvram in sysfs
This makes rtc-cmos export its NVRAM, like several other RTC drivers.
It still works within the limits of the current CMOS_READ/CMOS_WRITE calls,
which don't understand how to access multiple register banks. The primary
impact of that limitation is that Linux can't access the uppermost 128
bytes of NVRAM on many systems.
Note that this isn't aiming to be a drop-in replacement for the legacy
/dev/nvram support. (Presumably that has real users, and isn't just
getting carried forward automatically?) Userspace handles more work:
- When userspace code updates NVRAM, that will need to include
updating any platform-specific checksums that may apply.
- No /proc/driver/nvram file will parse and display NVRAM data
according to whichever boot firmware your board expects.
Also minor pnp-related updates: update a comment, remove dead code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc-s3c: Use is_power_of_2() macro for simplicity.
Use is_power_of_2() macro for simplicity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean Delvare [Wed, 6 Feb 2008 09:38:41 +0000 (01:38 -0800)]
rtc-pcf8583: Don't abuse I2C_M_NOSTART
The rtc-pcf8583 driver is using the I2C_M_NOSTART flag but shouldn't. This
flag is only meant for broken chips and the PCF8583 RTC chip is not one of
these.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miklos Szeredi [Wed, 6 Feb 2008 09:38:39 +0000 (01:38 -0800)]
fuse: limit queued background requests
Libfuse basically creates a new thread for each new request. This is fine for
synchronous requests, which are naturally limited. However background
requests (especially writepage) can cause a thread creation storm.
To avoid this, limit the number of background requests available to userspace.
This is done by introducing another queue for background requests, and a
counter for the number of "active" requests, which are currently available for
userspace.
Eric Sandeen [Wed, 6 Feb 2008 09:38:37 +0000 (01:38 -0800)]
ecryptfs: check for existing key_tfm at mount time
Jeff Moyer pointed out that a mount; umount loop of ecryptfs, with the same
cipher & other mount options, created a new ecryptfs_key_tfm_cache item
each time, and the cache could grow quite large this way.
Looking at this with mhalcrow, we saw that ecryptfs_parse_options()
unconditionally called ecryptfs_add_new_key_tfm(), which is what was adding
these items.
Refactor ecryptfs_get_tfm_and_mutex_for_cipher_name() to create a new
helper function, ecryptfs_tfm_exists(), which checks for the cipher on the
cached key_tfm_list, and sets a pointer to it if it exists. This can then
be called from ecryptfs_parse_options(), and new key_tfm's can be added
only when a cached one is not found.
With list locking changes suggested by akpm.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Cc: Michael Halcrow <mhalcrow@us.ibm.com> Cc: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log