Milton Miller [Mon, 20 Oct 2008 15:37:04 +0000 (15:37 +0000)]
powerpc: Always trim numa memory to lmb_end_of_DRAM()
numa_enforce_memory_limit tried to be smart and only call lmb_end_of_DRAM
when a memory limit was set via mem= on the command line. However,
the early boot code will also limit memory added to the lmb system
when iommu=off is specified. When this happens, the page allocator
is given pages not in the linear mapping and this results in a fatal
data reference to the unmapped page.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Milton Miller [Mon, 20 Oct 2008 15:37:03 +0000 (15:37 +0000)]
powerpc: Use cpu_thread_in_core in smp_init for of_spin_map
We used to assume that even numbered threads were the primary
threads, ie those that would be listed and started as a cpu from
open firmware. Replace a left over is even (% 2) check with a check
for it being a primary thread and update the comments.
Tested with a debug print on pseries, identical code found for cell.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Milton Miller [Mon, 20 Oct 2008 15:37:03 +0000 (15:37 +0000)]
powerpc: Find and destroy possible stale kernel added properties
64 bit powerpc requires the kexec user space tools avoid overwriting
the static kernel image and translation hash table when choosing
where to put memory image data because it copies the data into place
using the kernels virtual memory system. Kexec userspace determines
these and other areas blocked by reading properties the kernel adds,
but does not filter these properties when creating the device tree
for the next kernel.
When the second kernel tries to add its values for these properties,
the export via /proc/device-tree is hidden by the pre-existing but
stale values from the flat tree. Kexec userspace reads the old
property, allocates the new kernel at the old kernel's end, and
gets rejected by the overlap check.
Search and remove these stale properties before adding the new values.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kumar Gala [Mon, 20 Oct 2008 03:16:55 +0000 (03:16 +0000)]
powerpc: Fix build issue with CONFIG_RELOCATABLE=y
There are two issues when we enable CONFIG_RELOCATABLE. The first is due
to the fact that phys_addr_t is now defined in linux/types.h. The second
is due to the fact that the DMA code changes expose memstart_addr to
prom_init.c
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mike Ditto [Fri, 17 Oct 2008 09:27:51 +0000 (09:27 +0000)]
powerpc: Fix boot wrapper memcmp() called with zero length argument
I noticed, when trying to use, e.g.,
node = find_node_by_prop_value(prev, "booleanprop", "", 0))
to search for all nodes with a certain boolean property, that memcmp()
returns garbage when comparing zero bytes. It should return zero.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jon Tollefson [Thu, 16 Oct 2008 18:59:43 +0000 (18:59 +0000)]
powerpc/numa: Make memory reserve code more robust
Adjust amount to reserve based on previous nodes for reserves spanning
multiple nodes. Check if the node active range is empty before attempting
to pass the reserve to bootmem. In practice the range shouldn't be empty,
but to be sure we check.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Carl Love [Tue, 14 Oct 2008 23:37:01 +0000 (23:37 +0000)]
powerpc/oprofile: Fix mutex locking for cell spu-oprofile
The issue is the SPU code is not holding the kernel mutex lock while
adding samples to the kernel buffer.
This patch creates per SPU buffers to hold the data. Data
is added to the buffers from in interrupt context. The data
is periodically pushed to the kernel buffer via a new Oprofile
function oprofile_put_buff(). The oprofile_put_buff() function
is called via a work queue enabling the funtion to acquire the
mutex lock.
The existing user controls for adjusting the per CPU buffer
size is used to control the size of the per SPU buffers.
Similarly, overflows of the SPU buffers are reported by
incrementing the per CPU buffer stats. This eliminates the
need to have architecture specific controls for the per SPU
buffers which is not acceptable to the OProfile user tool
maintainer.
The export of the oprofile add_event_entry() is removed as it
is no longer needed given this patch.
Note, this patch has not addressed the issue of indexing arrays
by the spu number. This still needs to be fixed as the spu
numbering is not guarenteed to be 0 to max_num_spus-1.
Signed-off-by: Carl Love <carll@us.ibm.com> Signed-off-by: Maynard Johnson <maynardj@us.ibm.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Acked-by: Robert Richter <robert.richter@amd.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nathan Fontenot [Mon, 13 Oct 2008 08:42:00 +0000 (08:42 +0000)]
powerpc/pseries: Validate PFN in pseries_remove_lmb()
The pfn of the memory to be removed should be validated prior to
attempting to remove the memory. In cases where the probe of a
memory section fails during hotplug add, the pfn for the lmb may
not be valid.
powerpc/boot: Compare _start against ei.loadsize instead ei.memsize
If the vmlinux binary in memory is larger than 4 MiB than it collides
with the initial boot code which is linked at 4 MiB in case of cuBoot.
If the the uncompressed image size (on disk size) is less than 4 MiB
then it would fit. The difference between those two sizes is the bss
section. In cuBoot we have the dtb embedded right after the data
section so it is very likely that the reset of the bss section (in
kernel's start up code) will overwrite the dtb blob. Therefore we
reallocate the dtb. Something similar is allready done to the initrd.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jeremy Kerr [Thu, 16 Oct 2008 00:11:12 +0000 (11:11 +1100)]
powerpc/spufs: Don't spu_acquire_saved unnecessarily in regs read
With most file readers (eg cat, dd), reading a context's regs file will
result in two reads: the first to read the data, and the second to
return EOF. Because each read performs a spu_acquire_saved, we end up
descheduling and re-scheduling the context twice.
This change does a simple check to see if we'd return EOF before
calling spu_acquire_saved(), saving the extra schedule operation.
Jeremy Kerr [Wed, 15 Oct 2008 23:51:46 +0000 (10:51 +1100)]
powerpc/spufs: Don't require full buffer in switch_log read
Currently, read() on the sputrace log will block until the read buffer
is full. This makes it difficult to retrieve the end of the buffer, as
the user will need to read with the right-sized buffer.
Jeremy Kerr [Wed, 15 Oct 2008 23:03:46 +0000 (10:03 +1100)]
powerpc/spufs: Use state_mutex for switch_log locking, and prevent multiple openers
Currently, we use ctx->mapping_lock and ctx->switch_log->lock for the
context switch log. The mapping lock only prevents concurrent open()s,
so we require the switch_lock->lock for reads.
Since writes to the switch log buffer occur on context switches, we're
better off synchronising with the state_mutex, which is held during a
switch. Since we're serialised througout the buffer reads and writes,
we can use the state mutex to protect open and release too, and
can now kfree() the log buffer on release. This allows us to perform
the switch log notify without taking any extra locks.
Because the buffer is only present while the file is open, we can use
it to prevent multiple simultaneous openers.
Jeremy Kerr [Wed, 15 Oct 2008 02:20:42 +0000 (13:20 +1100)]
powerpc/spufs: sputrace: Don't block until the read buffer is full
Currently, read() on the sputrace buffer will only return data when
the user buffer is exhausted. This may mean that we never see the
end of the event log, unless we read() with exactly the right-sized
buffer.
This change makes sputrace_read not block if we have data ready to
return.
Jeremy Kerr [Wed, 15 Oct 2008 02:16:18 +0000 (13:16 +1100)]
powerpc/spufs: sputrace: Only enable logging on open(), prevent multiple openers
Currently, sputrace will start logging to the event buffer before the
log buffer has been open()ed. This results in a heap of "lost samples"
warnings if the sputrace file hasn't yet been opened.
Since the buffer is reset on open() anyway, there's no need to enable
logging when no-one has opened the log.
Because open clears the log, make it return EBUSY for mutliple open
calls.
Josh Boyer [Thu, 16 Oct 2008 04:38:40 +0000 (04:38 +0000)]
ibm_newemac: Fix new MAL feature handling
Support for new features needed by the PPC 405EZ boards
introduced some errors in the MAL and EMAC feature handling.
This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is
not set for those.
This patch fixes these errors by wrapping the code in the
appropriate #ifdefs.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
powerpc/40x: Add PowerPC 40x simple platform support
This adds a common board file for almost all of the "simple" PowerPC 40x
boards that exist today. This is intended to be a single place to add
support for boards that do not differ in platform support from most of the
evaluation boards that are used as reference platforms. Boards that have
specific requirements or custom hardware setup should still have their own
board.c file.
The first board ported to this is the AMCC PowerPC 405EZ Acadia board.
Add the base DTS for the AMCC PowerPC 405EZ Acadia evalution board.
In addition to some of the normal PPC 40x peripherals, the Acadia
board has:
- 64 MiB PSRAM
- NOR and NAND flash
- Two USB 1.1 host ports
- Two CAN 2.0 ports
- ADC and DAC connectors
- LCD display
This adds the basic platform support to build from.
Linus Torvalds [Wed, 15 Oct 2008 17:22:21 +0000 (10:22 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Kill unused <asm/debug.h> inclusions
MIPS: IP32: Add platform device for CMOS RTC; remove dead code
RTC: M48T35: new RTC driver
MIPS: IP27: Switch over to RTC class driver
MIPS: DS1286: New RTC driver
MIPS: IP22/28: Switch over to RTC class driver
MIPS: PCI: Scan busses when they are registered
MIPS: WGT634U: Add reset button support
MIPS: BCM47xx: Use the new SSB GPIO API
MIPS: BCM47xx: Remove references to BCM947XX
MIPS: WGT634U: Add machine detection message
MIPS: Align .data.cacheline_aligned based on CONFIG_MIPS_L1_CACHE_SHIFT
MIPS: show_cpuinfo prints the type of the calling CPU
MIPS: Fix wrong branch target in new spin_lock code.
MIPS: Have a heart for a lonely, lost header file ...
Arjan van de Ven [Wed, 15 Oct 2008 09:52:34 +0000 (10:52 +0100)]
tty: make sure that proc_clear_tty stores the cpu flags
proc_clear_tty() gets called with interrupts off (while holding the task list
lock) from sys_setid. This means that it needs the _irqsave version of the
locking primitives.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com> Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Read & write functions now call a generic transfer function, so identical
code in both routines could be eliminated. The result is easier to maintain
and smaller in source and binary code. Also, fix some checkpatch warnings.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfram Sang [Wed, 15 Oct 2008 17:09:59 +0000 (11:09 -0600)]
powerpc/mpc5200: Don't touch pipelining for MPC5200B
MPC5200 needs to have pipelining disabled for ATA to work. MPC5200B does not.
So, for the latter, don't touch the original setting from the bootloader.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When we skip unrecognized options in xfs_fs_remount we should just break
out of the switch and not return because otherwise we may skip clearing
the xfs-internal read-only flag. This will only show up on some
operations like touch because most read-only checks are done by the VFS
which thinks this filesystem is r/w. Eventually we should replace the
XFS read-only flag with a helper that always checks the VFS flag to make
sure they can never get out of sync.
Bug reported and fix verified by Marcel Beister on #xfs.
Bug fix verified by updated xfstests/189.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Timothy Shimmin <tes@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 15 Oct 2008 15:07:35 +0000 (08:07 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
Linus Torvalds [Tue, 14 Oct 2008 23:53:02 +0000 (16:53 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-viapro: Add support for SMBus Process Call transactions
i2c: Restore i2c_smbus_process_call function
i2c: Do earlier driver model init
i2c: Only build Tyan SMBus mux drivers on x86
i2c: Guard against oopses from bad init sequences
i2c: Document the implementation details of the /dev interface
i2c: Improve dev-interface documentation
i2c-parport-light: Don't register a platform device resource
hwmon: (dme1737) Convert to a new-style i2c driver
hwmon: (dme1737) Be less i2c-centric
i2c/tps65010: Vibrator hookup to gpiolib
i2c-viapro: Add VX800/VX820 support
i2c: Renesas Highlander FPGA SMBus support
i2c-pca-isa: Don't grab arbitrary resources
i2c/isp1301_omap: Convert to a new-style i2c driver, part 2
i2c/isp1301_omap: Convert to a new-style i2c driver, part 1
Linus Torvalds [Tue, 14 Oct 2008 23:35:43 +0000 (16:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
Linus Torvalds [Tue, 14 Oct 2008 23:34:11 +0000 (16:34 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
ocfs2: Make cached block reads the common case.
ocfs2: Kill the last naked wait_on_buffer() for cached reads.
ocfs2: Move ocfs2_bread() into dir.c
ocfs2: Simplify ocfs2_read_block()
ocfs2: Require an inode for ocfs2_read_block(s)().
ocfs2: Separate out sync reads from ocfs2_read_blocks()
ocfs2: Refactor xattr list and remove ocfs2_xattr_handler().
ocfs2: Calculate EA hash only by its suffix.
ocfs2: Move trusted and user attribute support into xattr.c
ocfs2: Uninline ocfs2_xattr_name_hash()
ocfs2: Don't check for NULL before brelse()
ocfs2: use smaller counters in ocfs2_remove_xattr_clusters_from_cache
ocfs2: Documentation update for user_xattr / nouser_xattr mount options
ocfs2: make la_debug_mutex static
ocfs2: Remove pointless !!
ocfs2: Add empty bucket support in xattr.
ocfs2/xattr.c: Fix a bug when inserting xattr.
ocfs2: Add xattr mount option in ocfs2_show_options()
ocfs2: Switch over to JBD2.
ocfs2: Add the 'inode64' mount option.
...
Bjorn Helgaas [Tue, 14 Oct 2008 23:01:59 +0000 (17:01 -0600)]
rtc-cmos: look for PNP RTC first, then for platform RTC
We shouldn't rely on "pnp_platform_devices" to tell us whether there
is a PNP RTC device.
I introduced "pnp_platform_devices", but I think it was a mistake.
All it tells us is whether we found any PNPBIOS or PNPACPI devices.
Many machines have some PNP devices, but do not describe the RTC
via PNP. On those machines, we need to do the platform driver probe
to find the RTC.
We should just register the PNP driver and see whether it claims anything.
If we don't find a PNP RTC, fall back to the platform driver probe.
This (in conjunction with the arch/x86/kernel/rtc.c patch to add
a platform RTC device when PNP doesn't have one) should resolve
these issues:
powerpc: Fix CHRP PCI config access for indirect_pci
Recently, indirect_pci was changed to test if the bus number requested
is the one hanging straight off the PHB, then it substitutes the bus
number with another one contained in a new "self_busno" field of the
pci_controller structure.
However, this breaks CHRP which didn't initialize this new field, and
which relies on having the right bus number passed to the hardware.
This fixes it by initializing this variable properly for all CHRP bridges
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
The detection of the IBM "Python" PCI host bridge on IBM CHRP
machines such as old RS6000 was broken when we changed
of_device_is_compatible() from strncasecmp to strcasecmp (dropped
the "n" variant) due to the way IBM encodes the chip version.
We fix that by instead doing a match on the model property like
we do for others bridges in that file. It should be good enough
for those machines. If yours is still broken, let me know.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Fix link errors on 32-bit machines using legacy DMA
The new merged DMA code will try to access isa_bridge_pcidev when
trying to DMA to/from legacy devices. This is however only defined
on 64-bit. Fixes this for now by adding the variable, even if it
stays NULL. In the long run, we'll make isa-bridge.c common to
32 and 64-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pci: Improve detection of unassigned bridge resources
When the powerpc PCI layer is not configured to re-assign everything,
it currently fails to detect that a PCI to PCI bridge has been left
unassigned by the firmware and tries to allocate resource for the
default window values in the bridge (0...X) (with the notable exception
of a hack we have in there that detects some Apple firmware unassigned
bridge resources).
This results in resource allocation failures, which are generally
fixed up later on but it causes scary warnings in the logs and we
have seen the fixup code fall over in some circumstances (a different
issue to fix as well).
This code improves that by providing a more complete & useful function
to intuit that a bridge was left unassigned by the firmware, and thus
force a full re-allocation by the PCI code without trying to allocate
the existing useless resources first.
The algorithm we use basically considers unassigned a window that
starts at 0 (PCI address) if the corresponding address space enable
bit is not set. In addition, for memory space, it considers such a
resource unassigned also if the host bridge isn't configured to
forward cycles to address 0 (ie, the resource basically overlaps
main memory).
This fixes a range of problems with things like Bare-Metal support
on pSeries machines, or attempt to use partial firmware PCI setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 611e097d7707741a336a0677d9d69bec40f29f3d
Author: Christian Borntraeger <borntraeger@de.ibm.com>
hvc_console: rework setup to replace irq functions with callbacks
introduced a spinlock recursion problem. The notifier_del is
called with a lock held, and in turns calls free_irq which then
complains when manipulating procfs. This fixes it by moving the
call to the notifier to outside of the locked section.
Signed-off-by: Christian Borntraeger<borntraeger@de.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jiri Kosina [Tue, 14 Oct 2008 21:37:33 +0000 (23:37 +0200)]
HID: build drivers for all quirky devices by default
Once kernel configuration has CONFIG_HID turned on, let also all the
specialized drivers for quirky devices to be built (unless CONFIG_EMBEDDED is
specified), as usually users don't care that much which driver
gives them the functionality, but when they want generic support, they
probably want to have support for all the quirky devices as well.
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Anssi Hannula [Sat, 4 Oct 2008 12:44:06 +0000 (14:44 +0200)]
HID: fix a lockup regression when using force feedback on a PID device
Commit 8006479c9b75fb6594a7b746af3d7f1fbb68f18f introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
hid_compat_load() runs on the default workqueue, it request_module(), it
execs modprobe, it exits, tty flushes default workqueue, it hangs, because
we are still in it.
HID: report descriptor fix for remaining MacBook JIS keyboards
This patch fixes a problem that MacBook JIS keyboard sends wrong report
descriptors. Although it has already been fixed in the first Core 2 Duo model,
it still remains in other models of MacBook.
HID: Autocentering support for Logitech MOMO Racing Wheel
Current kernel has no support for autocentering for Logitech wheels. By
default autocentering enabled in wheel and constant effect does not work
properly. Using USB sniffer I found command which change autocentering
settings: 0xFE, 0x0D, 0x0R, 0x0L, 0x80, 0x00, 0x00, where R - clockwise force,
L - counter-clockwise (0x0-0xF, 0xC = 100%).
Richard Hughes [Wed, 27 Aug 2008 09:19:37 +0000 (11:19 +0200)]
HID: remove ignore quirk for MGE UPS devices
This patch reverts the change made four years ago here:
http://www.vg.kernel.org/pub/linux/kernel/people/gregkh/usb/2.4/usb-hid-2.4.25-pre7.patch
UPS's made by MGE can be used with usbhid just fine, and by removing the
ignore quirk allows them to be used with HAL so they just work when plugged
in, without needing to be manually configured.
With the ignore quirk in place a user would have to configure NUT before the
UPS could be used, as NUT uses it's own internal USB matching framework
to match against the USB devices, do low level control messages on the
device and then parse the HID tables all in userspace.
This is not needed, as allowing the device to be claimed as a usbhid device
allows it to be used like any other USB UPS device. The devices correctly
advertise the power device page which can be queried for the device state.
I assume the quirk was changed so that people using < libusb 0.1.8 could
still use NUT's internal HID code to manage the UPS.
libusb 0.1.8 was released quite some time ago: 2004-02-11.
This patch does not break NUT as in drivers/libusb.c the device is force
unbound from the kernel driver using usb_detach_kernel_driver_np () where
it can be controlled like normal.
[jkosina@suse.cz: adapt to the new hidbus code]
Signed-off-by: Richard Hughes <rhughes@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Wed, 20 Aug 2008 17:13:52 +0000 (19:13 +0200)]
HID: introduce list for hiddev creation forcing
Introduce a list of devices for which there is need to
force a creation of the hiddev interface, but still they
are operated by generic driver (i.e. certain UPS).
projects / linux-2.6-omap-h63xx.git / log