Marek Vašut [Thu, 7 Dec 2006 01:14:07 +0000 (17:14 -0800)]
ARM: OMAP: Palm Zire71 minor fixes
This patch makes minor changes in palmz71 board file (formating changes) and
renames one GPIO (PALMZ71_PINTDAV_GPIO to PALMZ71_PENIRQ_GPIO) in
board-palmz71.h and board-palmz71.c .
Signed-off-by: Marek Vašut <marek.vasut@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: abstract debug card setup (smc, leds)
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:14:03 +0000 (17:14 -0800)]
ARM: OMAP: h4 must have blinky leds!!
This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.
It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.
In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO). Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
On Fri, Oct 27, 2006 at 05:16:59PM +0100, Jonathan McDowell wrote:
> However having prodded further I'm seeing incorrect key parsing with
> the omap-keypad driver under both -rc2 and -rc3 (works fine in
> 2.6.18-omap1). Numerous keys now returns strings of characters rather
> than the single expected character. A few keys still work as expected
> however. Before I dig in further is anyone else seeing anything similar?
This appears to be due to the addition of keymapsize to the
omap_kp_platform_data structure. The patch below fixes things up for
the Delta; other boards appear to have already had this done.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:59 +0000 (17:13 -0800)]
ARM: OMAP: gpio object shrinkage, cleanup
More GPIO/IRQ cleanup:
- compile-time removal of much useless code
* mpuio support on non-OMAP1.
* 15xx/730/24xx gpio support on 1610
* 15xx/730/16xx gpio support on 24xx
* etc
- remove all BUG() calls, which are always bad news ... replaced some
with normal fault reports for that call, others with WARN_ON(1).
- small mpuio bugfix: add missing set_type() method
Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:55 +0000 (17:13 -0800)]
ARM: OMAP: omap2/gpmc updates
GPMC updates:
- bugfixes: wrong/missing flags, omitted write, wrong test
- don't map memory segments starting at zero
- improve debug messaging
- export gpmc_get_fclk_perio]d() since it's needed to calc timings
- expect gpmc_cs_set_timings() caller to have initialized sync vs async
Note that this API is glitchy; likely the best fix would be to add
a member to "struct gpmc_timings" to hold GPMC_CONFIG1, since that
holds one key aspect of the GPMC timings (the gpmc_fclk divisor,
and sync vs. async == whether that divisor matters).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kyungmin Park [Thu, 7 Dec 2006 01:13:54 +0000 (17:13 -0800)]
ARM: OMAP: 24xx pinmux updates
Add some OMAP 24xx pin mux declarations to support:
- TUSB 6010 EVM (on H4)
- All three full speed USB ports
- GPIOs used with USB0 on Apollon and H4
For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Thu, 7 Dec 2006 01:13:53 +0000 (17:13 -0800)]
ARM: OMAP: /sys/kernel/debug/omap_gpio
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.
Includes minor bugfixes: recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds support for the keypad on the top of the Amstrad Delta. It's
just a standard omap-keypad so all we need to do is add the keypad
layout and platform data to the board definition file.
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Thu, 7 Dec 2006 01:13:52 +0000 (17:13 -0800)]
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
General update of the board file for Palm Tungsten E. Registers the
platform devices contained in the PDA (ROM chip, keypad, infra-red)
and updates the configuration for USB and MMC, whose config values
were previously guessed in most cases due to lack of documentation
(and now are confirmed by a number of users). Macros for GPIO pins are
moved to a file in include/asm-arm/arch-omap.
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Imre Deak [Thu, 7 Dec 2006 01:13:50 +0000 (17:13 -0800)]
ARM: OMAP: FB: add controller platform data
Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:13:51 +0000 (17:13 -0800)]
ARM: OMAP: Fix warning in clock.c
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP: correct misc 15xx and non-15xx platform code
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Matthew Percival [Fri, 26 Jan 2007 00:24:29 +0000 (16:24 -0800)]
ARM: OMAP: dmtimer.c omap1 register fix
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Arnaud Patard [Thu, 7 Dec 2006 01:14:06 +0000 (17:14 -0800)]
ARM: OMAP: board-nokia770: correct lcd name
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:14:04 +0000 (17:14 -0800)]
ARM: OMAP: Fix warning in mach-omap1
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:14:00 +0000 (17:14 -0800)]
ARM: OMAP: Fix warning in mach-omap2
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:14:00 +0000 (17:14 -0800)]
ARM: OMAP: Fix warnings in plat-omap
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Timo Teras [Thu, 7 Dec 2006 01:13:52 +0000 (17:13 -0800)]
ARM: OMAP: Proper handling of DMA4_IRQSTATUS_L0
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com> Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Dirk Behme [Thu, 7 Dec 2006 01:13:51 +0000 (17:13 -0800)]
ARM: OMAP: Fix warning in clock.c
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP: correct misc 15xx and non-15xx platform code
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Kyle McMartin [Tue, 27 Feb 2007 03:21:22 +0000 (22:21 -0500)]
[PARISC] clocksource: Move update_cr16_clocksource later in boot
smp_cpus_done is too early for us... before we even do a device
inventory! Move update_cr16_clocksource into the tail end of
processor_probe() and stub it out on CONFIG_SMP=n builds.
Verified that clocksource0 is properly updated to use jiffies
on an SMP build.
Atsushi Nemoto [Thu, 22 Feb 2007 15:39:48 +0000 (00:39 +0900)]
[MIPS] Kill redundant EXTRA_AFLAGS
Many Makefiles in arch/mips have EXTRA_AFLAGS := $(CFLAGS) line. This
is redundant while AFLAGS contains $(cflags-y) and any options only
listed in CFLAGS (not in cflags-y) should be unnecessary for asm
sources.
Linus Torvalds [Mon, 26 Feb 2007 22:55:48 +0000 (14:55 -0800)]
Revert "[CPUFREQ] constify cpufreq_driver where possible."
This reverts commit aeeddc1435c37fa3fc844f31d39c185b08de4158, which was
half-baked and broken. It just resulted in compile errors, since
cpufreq_register_driver() still changes the 'driver_data' by setting
bits in the flags field. So claiming it is 'const' _really_ doesn't
work.
Linus Torvalds [Mon, 26 Feb 2007 21:18:43 +0000 (13:18 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Correct debugging output when path record lookup fails
RDMA/cxgb3: Stop the EP Timer on BAD CLOSE
RDMA/cxgb3: cleanups
RDMA/cma: Remove unused node_guid from cma_device structure
IB/cm: Remove ca_guid from cm_device structure
RDMA/cma: Request reversible paths only
IB/core: Set hop limit in ib_init_ah_from_wc correctly
IB/uverbs: Return correct error for invalid PD in register MR
IPoIB: Remove unused local_rate tracking
IPoIB/cm: Improve small message bandwidth
IB/mthca: Make 2 functions static
Alan [Wed, 21 Feb 2007 16:41:23 +0000 (16:41 +0000)]
[PATCH] Fix oops in pata_pcmcia
The change to the devres layer re-orders the execution of cleanup
functions and in turn causes the pcmcia layer to oops as it zaps a
pointer now needed later on. We simply leave the pointer alone.
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland Dreier [Mon, 26 Feb 2007 20:57:08 +0000 (12:57 -0800)]
IPoIB: Correct debugging output when path record lookup fails
If path_rec_completion() is passed a non-NULL path record pointer
along with an unsuccessful status value, the tracing code incorrectly
prints the (invalid) DLID from the path record rather than the more
interesting status code. The actual logic of the function correctly
uses the path record only if the status indicates a successful lookup.
Ondrej Zajicek [Thu, 22 Feb 2007 16:00:41 +0000 (17:00 +0100)]
[PATCH] Fix build-failure in drivers/video/s3fb.c
Toralf Förster pointed out that drivers/video/s3fb.c would fail to compile:
> ...
> CC drivers/video/s3fb.o
> drivers/video/s3fb.c: In function `s3_pci_remove':
> drivers/video/s3fb.c:1003: warning: unused variable `par'
> drivers/video/s3fb.c: In function `s3fb_setup':
> drivers/video/s3fb.c:1141: error: `mtrr' undeclared (first use in this function)
> drivers/video/s3fb.c:1141: error: (Each undeclared identifier is reported only once
> drivers/video/s3fb.c:1141: error: for each function it appears in.)
> make[2]: *** [drivers/video/s3fb.o] Error 1
> make[1]: *** [drivers/video] Error 2
> make: *** [drivers] Error 2
Ingo Molnar [Thu, 22 Feb 2007 08:38:22 +0000 (09:38 +0100)]
[PATCH] x86: add -freg-struct-return to CFLAGS
Jeremy Fitzhardinge suggested the use of -freg-struct-return, which does
structure-returns (such as when using pte_t) in registers instead of on
the stack.
that is indeed so, and this option reduced the kernel size a bit:
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
Bernhard Walle [Mon, 26 Feb 2007 20:10:32 +0000 (12:10 -0800)]
[XFRM]: Fix oops in xfrm4_dst_destroy()
With 2.6.21-rc1, I get an oops when running 'ifdown eth0' and an IPsec
connection is active. If I shut down the connection before running 'ifdown
eth0', then there's no problem. The critical operation of this script is to
kill dhcpd.
This patch fixes that oops. I don't know the network code of the Linux
kernel in deep, so if that fix is wrong, please change it. But please
fix the oops. :)
Signed-off-by: Bernhard Walle <bwalle@suse.de> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris [Thu, 22 Feb 2007 23:11:31 +0000 (18:11 -0500)]
Reassign printk levels in selinux kernel code
Below is a patch which demotes many printk lines to KERN_DEBUG from
KERN_INFO. It should help stop the spamming of logs with messages in
which users are not interested nor is there any action that users should
take. It also promotes some KERN_INFO to KERN_ERR such as when there
are improper attempts to register/unregister security modules.
A similar patch was discussed a while back on list:
http://marc.theaimsgroup.com/?t=116656343500003&r=1&w=2
This patch addresses almost all of the issues raised. I believe the
only advice not taken was in the demoting of messages related to
undefined permissions and classes.
Signed-off-by: Eric Paris <eparis@redhat.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
security/selinux/hooks.c | 20 ++++++++++----------
security/selinux/ss/avtab.c | 2 +-
security/selinux/ss/policydb.c | 6 +++---
security/selinux/ss/sidtab.c | 2 +-
4 files changed, 15 insertions(+), 15 deletions(-) Signed-off-by: James Morris <jmorris@namei.org>
[XFRM_TUNNEL]: Reload header pointer after pskb_may_pull/pskb_expand_head
Please consider applying, this was found on your latest
net-2.6 tree while playing around with that ip_hdr() + turn
skb->nh/h/mac pointers as offsets on 64 bits idea :-)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Having a work queue for checking carrier leads to lots of race issues.
Simpler to just get the cost when data structure is created and
update on change.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 21 Feb 2007 16:53:47 +0000 (01:53 +0900)]
[IPV4] devinet: Register inetdev earlier.
This patch allocates inetdev at registration for all devices
in line with IPv6. This allows sysctl configuration on the
devices to occur before they're brought up or addresses are
added.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>