Sonic Zhang [Thu, 5 Mar 2009 10:26:59 +0000 (18:26 +0800)]
Blackfin arch: Fix bug - KGDB single step into the middle of a 4 bytes instruction on bf561 after soft bp is hit
Run IFLUSH twice to avoid loading wrong instruction
after invalidating icache and following sequence is met.
1) The one instruction address is cached in the icache.
2) This instruction in SDRAM is changed.
3) IFLASH[P0] is executed only once in lackfin_icache_flush_range().
4) This instruction is executed again, but not the changed new one.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enrik Berkhan [Thu, 5 Mar 2009 06:42:30 +0000 (14:42 +0800)]
Blackfin arch: fix bug - The SPORT_HYS bit is not set for BF561 0.5
IMHO the setting should depend on ANOMALY_05000305 which is about the
availability of the bit, not ANOMALY_05000265 which only describes the
SPORT sensitivity to noise (checked for BF561 only, though).
If that's not true for other BF variants, maybe the definition of
ANOMALY_05000265 for BF561 should be changed to '(1)' instead.
Tom Parker [Tue, 3 Mar 2009 09:59:39 +0000 (17:59 +0800)]
Blackfin arch: fix bug - Error if one serial has hardware flow control and the other doesn't
I have a system where UART0 is configured with hardware flow control, but UART1
doesn't have it enabled. Attempting to access UART1 in this configuration
results in the following error in dmesg:
This is because the #ifdef's in bfin_serial_5xx.h are messed up. More
specifically, they add/remove the uart_{rts,cts}_pin fields in
bfin_serial_resources based on whether the particular port has rts/cts enabled,
as opposed to when either port has it enabled.
This patch fixed this.
Signed-off-by: Tom Parker <blackfin@tevp.net> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
Tony Breeds [Tue, 3 Mar 2009 17:59:30 +0000 (17:59 +0000)]
powerpc: Run sbc610 USB fixup code only on the appropriate platform.
commit a969e76a7101bf5f3d369563df1ca1253dd6131b (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.
Linus Torvalds [Tue, 3 Mar 2009 22:33:20 +0000 (14:33 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: don't allow setuid to succeed if the user does not have rt bandwidth
sched_rt: don't start timer when rt bandwidth disabled
Linus Torvalds [Tue, 3 Mar 2009 22:32:55 +0000 (14:32 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
Linus Torvalds [Tue, 3 Mar 2009 22:32:37 +0000 (14:32 -0800)]
Merge branch 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
Linus Torvalds [Tue, 3 Mar 2009 22:32:04 +0000 (14:32 -0800)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Teach RCU that idle task is not quiscent state at boot
Russell King [Tue, 3 Mar 2009 13:43:47 +0000 (13:43 +0000)]
[ARM] fix lots of ARM __devexit sillyness
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Tue, 3 Mar 2009 10:44:12 +0000 (11:44 +0100)]
[ARM] 5417/1: Set the correct cacheid for ARMv6 CPUs with ARMv7 style MMU
The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Seth Forshee [Mon, 2 Mar 2009 21:39:36 +0000 (22:39 +0100)]
[ARM] 5416/1: Use unused address in v6_early_abort
The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack. If the store succeeeds this
corrupts r0 in pt_regs. Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Yinghai Lu [Tue, 3 Mar 2009 07:36:13 +0000 (23:36 -0800)]
x86: fix init_memory_mapping() to handle small ranges
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Tue, 3 Mar 2009 00:23:33 +0000 (16:23 -0800)]
Revert "menu: fix embedded menu snafu"
This reverts commit 155b25bcc28631a5b5230191aa3f56c40dfffa3f, which was
totally wrong - the "embedded" options still exists (very much so) even
on non-embedded platforms.
It's just that we don't bother with actually asking about them when
we're not embedded, we just take their default values (which is usually
'y' - the options add features that may not be worth it in a constrained
environment).
Noticed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 3 Mar 2009 00:11:36 +0000 (16:11 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix use-before-null-check in i915_irq_emit().
drm: Avoid client deadlocks when the master disappears.
drm: Wake up all lock waiters when the master disappears.
drm: Don't return ERESTARTSYS to user-space.
drm: Avoid client deadlocks when the master disappears.
This is done by
1) Wake up lock waiters when we close the master file descriptor.
Not when the master structure is removed, since the latter
requires the waiters themselves to release the refcount on the
master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
Normally these clients will get a SIGPIPE when the X server dies,
but clients may also spin trying to grab the DRM lock, without
getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Dave Airlie <airlied@linux.ie>
Randy Dunlap [Mon, 2 Mar 2009 22:14:06 +0000 (14:14 -0800)]
menu: fix embedded menu snafu
The COMPAT_BRK kconfig symbol does not depend on EMBEDDED, but it is in
the midst of the EMBEDDED menu symbols, so it mucks up the EMBEDDED
menu. Fix by moving it to just after all of the EMBEDDED menu symbols.
Also, surround all of the EMBEDDED symbols with "if EMBEDDED"/"endif" so
that this EMBEDDED block is clearer.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 2 Mar 2009 23:48:00 +0000 (15:48 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
sdhci: Add quirk for controllers with no end-of-busy IRQ
Linus Torvalds [Mon, 2 Mar 2009 23:47:19 +0000 (15:47 -0800)]
Merge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add probe_mask default for Toshiba laptop with ALC268
ALSA: hda - Add quirk for new HP xw series
ALSA: hda - Fix digital mic on dell-m4-1 and dell-m4-3
Linus Torvalds [Mon, 2 Mar 2009 23:47:01 +0000 (15:47 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
zaurus: add usb id for motomagx phones
usbnet: make usbnet_get_link() fall back to ethtool_op_get_link()
veth: Fix carrier detect
cdc_ether: add usb id for Ericsson F3507g
r8169: read MAC address from EEPROM on init (2nd attempt)
tcp: fix retrans_out leaks
net headers: export dcbnl.h
net headers: cleanup dcbnl.h
netpoll: Add drop checks to all entry points
gianfar: Do right check on num_txbdfree
pkt_sched: sch_drr: Fix oops in drr_change_class.
b44: Disable device on shutdown
b44: Unconditionally enable interrupt routing on reset
net: fix hp-plus build error
libertas: fix misuse of netdev_priv() and dev->ml_priv
ipv6: don't use tw net when accounting for recycled tw
asix: new device ids
tcp_scalable: Update malformed & dead url
netfilter: xt_recent: fix proc-file addition/removal of IPv4 addresses
netxen: handle pci bar 0 mapping failure
...
Linus Torvalds [Mon, 2 Mar 2009 23:43:03 +0000 (15:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
Linus Torvalds [Mon, 2 Mar 2009 23:42:26 +0000 (15:42 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: don't call jbd2_journal_force_commit_nested without journal
ext4: Reorder fs/Makefile so that ext2 root fs's are mounted using ext2
ext4: Remove duplicate call to ext4_commit_super() in ext4_freeze()
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt: fix disable lsi sas to use msi as default
[SCSI] fix ABORTED_COMMAND looping forever problem
[SCSI] sd: revive sd_index_lock
[SCSI] cxgb3i: update the driver version to 1.0.1
[SCSI] cxgb3i: Fix spelling errors in documentation
[SCSI] cxgb3i: added missing include in cxgb3i_ddp.h
[SCSI] cxgb3i: Outgoing pdus need to observe skb's MAX_SKB_FRAGS
[SCSI] cxgb3i: added per-task data to track transmit progress
[SCSI] cxgb3i: transmit work-request fixes
[SCSI] hptiop: Add new PCI device ID
Roland McGrath [Sat, 28 Feb 2009 07:25:54 +0000 (23:25 -0800)]
x86-64: seccomp: fix 32/64 syscall hole
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Sat, 28 Feb 2009 03:03:24 +0000 (19:03 -0800)]
x86-64: syscall-audit: fix 32/64 syscall hole
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Mon, 2 Mar 2009 20:48:20 +0000 (21:48 +0100)]
sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
As described here: http://lkml.org/lkml/2009/2/20/265
The CAFE chip is broken due to commit e809517f6fa5803a5a1cd5602.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279 that fixes
CAFE's problem. This adds the quirk for CAFE.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Ben Dooks [Fri, 20 Feb 2009 17:33:08 +0000 (20:33 +0300)]
sdhci: Add quirk for controllers with no end-of-busy IRQ
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Pekka Paalanen [Tue, 24 Feb 2009 19:44:15 +0000 (21:44 +0200)]
x86 mmiotrace: fix race with release_kmmio_fault_page()
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Stuart Bennett <stuart@freedesktop.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stuart Bennett [Thu, 5 Feb 2009 11:02:02 +0000 (11:02 +0000)]
x86 mmiotrace: improve handling of secondary faults
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org> Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Stuart Bennett <stuart@freedesktop.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stuart Bennett [Fri, 30 Jan 2009 17:38:59 +0000 (17:38 +0000)]
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org> Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pekka Paalanen [Sun, 1 Mar 2009 14:10:08 +0000 (16:10 +0200)]
x86: add far read test to testmmiotrace
Apparently pages far into an ioremapped region might not actually be
mapped during ioremap(). Add an optional read test to try to trigger a
multiply faulting MMIO access. Also add more messages to the kernel log
to help debugging.
This patch is based on a patch suggested by
Stuart Bennett <stuart@freedesktop.org>
who discovered bugs in mmiotrace related to normal kernel space faults.
Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Stuart Bennett <stuart@freedesktop.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pekka Paalanen [Sun, 1 Mar 2009 14:09:14 +0000 (16:09 +0200)]
x86: count errors in testmmiotrace.ko
Check the read values against the written values in the MMIO read/write
test. This test shows if the given MMIO test area really works as
memory, which is a prerequisite for a successful mmiotrace test.
Signed-off-by: Pekka Paalanen <pq@iki.fi> Cc: Stuart Bennett <stuart@freedesktop.org> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Takashi Iwai [Sun, 1 Mar 2009 09:55:44 +0000 (10:55 +0100)]
ALSA: hda - Add probe_mask default for Toshiba laptop with ALC268
Some Toshiba laptops have another ALC268 codec on slot#3 that conflicts
with the primary codec. The codec#3 is for the digital I/O, and should
be fixed by the driver, but it'd need a bunch of changes.
So, let's fix the probe problem temporarily by setting the default
probe_mask value.
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Mon, 2 Mar 2009 04:45:40 +0000 (20:45 -0800)]
usbnet: make usbnet_get_link() fall back to ethtool_op_get_link()
Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate. cdc_ether is an example of
such a driver.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.
So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 25 Feb 2009 04:33:58 +0000 (04:33 +0000)]
cdc_ether: add usb id for Ericsson F3507g
The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up. This patch adds the device id to cdc_ether.c as a workaround.
Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c. See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Mon, 2 Mar 2009 04:34:48 +0000 (20:34 -0800)]
r8169: read MAC address from EEPROM on init (2nd attempt)
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Fri, 27 Feb 2009 20:00:03 +0000 (15:00 -0500)]
selinux: Fix a panic in selinux_netlbl_inode_permission()
Rick McNeal from LSI identified a panic in selinux_netlbl_inode_permission()
caused by a certain sequence of SUNRPC operations. The problem appears to be
due to the lack of NULL pointer checking in the function; this patch adds the
pointer checks so the function will exit safely in the cases where the socket
is not completely initialized.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Ilpo Järvinen [Sun, 1 Mar 2009 08:21:36 +0000 (00:21 -0800)]
tcp: fix retrans_out leaks
There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Tested-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Leech [Fri, 27 Feb 2009 10:01:36 +0000 (10:01 +0000)]
net headers: cleanup dcbnl.h
1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
consistent with use of kernel types
Signed-off-by: Chris Leech <christopher.leech@intel.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sun, 1 Mar 2009 08:11:52 +0000 (00:11 -0800)]
netpoll: Add drop checks to all entry points
The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll. Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points. The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.
This patch adds the netpoll check to all entry points.
I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code). The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler
you're going to get a nice BUG_ON.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Some Logitech mice react to the magic knock like Elantech touchpad would.
This leads to those mice being misdetected as Elantech touchpads. Add a
version query to elantech_detect() to distinguish the two.
[dtor@mail.ru:
- lower severity of some messages - when we are not sure yet if
device is Elantech or not not responding to knock is not an error.
]
Andy Whitcroft [Sat, 28 Feb 2009 20:51:01 +0000 (12:51 -0800)]
Input: synaptics - ensure we reset the device on resume
When resuming from suspend newer Synaptics touchpads do not recover
correctly. Analysis of the resume sequence as applied in Linux was
compared to that of other operating systems. This indicated that the
other OSs were resetting the mouse before attempting to detect it (for
all Synaptics touchpads, old and new). Applying this same modification
fixes these newer Synaptics touchpads and brings the driver into line
with common OS reset behaviour.
Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Devices confirmed to be real HID have the class set to HID and the protocol
set to 'mouse'. Some have HID class but protocol set to 'none'. Those are
not HID and should be driven by usbtouchscreen.
Fix the device ignoring macro by adding match for the protocol too.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: musb: fix srp sysfs entry deletion
USB: musb: resume suspended root hub on disconnect
USB: musb: use right poll limit for low speed devices
USB: musb: be careful with 64K+ transfer lengths, host side
USB: musb: fix data toggle saving with shared FIFO
USB: musb: host endpoint_disable() oops fixes
USB: musb: fix urb_dequeue() method
USB: musb: fix musb_host_tx() for shared endpoint FIFO
USB: musb: be careful with 64K+ transfer lengths (gadget side)
usb: musb: make Davinci *work* in mainline
USB: usb_get_string should check the descriptor type
USB: gadget: fix build error in omap_apollon_2420_defconfig
USB: g_file_storage: automatically disable stalls under Atmel
USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
USB: Quirk for Hummingbird huc56s / Conexant ACM modem
USB: serial: add support for second revision of Ericsson F3507G WWAN card
USB: cdc-acm: add usb id for motomagx phones
USB: option: add BenQ 3g modem information
usb: gadget: obex: select correct ep descriptors
USB: EHCI: slow down ITD reuse
...
Linus Torvalds [Sat, 28 Feb 2009 00:48:33 +0000 (16:48 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Revert "MIPS: Print irq handler description"
MIPS: CVE-2009-0029: Enable syscall wrappers.
MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0
MIPS: Only allow Cavium OCTEON to be configured for boards that support it
Linus Torvalds [Sat, 28 Feb 2009 00:43:05 +0000 (16:43 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
Linus Torvalds [Sat, 28 Feb 2009 00:40:00 +0000 (16:40 -0800)]
Merge branch 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: ap325rxa: Revert ov772x support.
serial: sh-sci: fix overrun error handling for SH7785 SCIF.
sh: Storage class should be before const qualifier
Commit 8e961870bb9804110d5c8211d5d9d500451c4518 removed the FREEZE/THAW
handling in xfs_compat_ioctl but never added any compat handler back, so
now any freeze/thaw request from a 32-bit binary ond 64-bit userspace
will fail.
As these ioctls are 32/64-bit compatible two simple COMPATIBLE_IOCTL
entries in fs/compat_ioctl.c will do the job.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log