Hans de Goede [Fri, 25 Aug 2006 08:24:20 +0000 (10:24 +0200)]
[PATCH] hwmon: abituguru timeout fixes
This patch contains 2 sets of fixes for the abituguru:
1) Much improved timeout handling, drasticly reducing the amount of
timeout errors on some motherboards
2) Fix the exit paths in the bank1 sensor type detect code to always
restore the original settings even on an error. Without this our
special test settings could remain seriously confusing the system
BIOS's setup menu.
Both are very much related and are must haves, to avoid messing up the
uguru CMOS settings.
Detailed changes:
- Much improved timeout / wait for status handling. Many thanks to Sunil
Kumar, for all his testing, ideas and patches! The code now first busy
waits, polling the uguru for the expected status as this usually
succeeds pretty quickly (within 90 reads). To avoid unnecessary CPU burn
in timeout conditions, the amount of busy waiting has been halved from
previous versions (120 tries instead of 250). This is not a problem,
because this version goes to sleep after 120 attemps for 1 jiffy and
then tries again, it does this sleep and try again 5 times before
finally giving up. This (almost?) completly removes the timeout errors
some people have seen regulary. Apparently some older uguru versions
sometimes are distracted for a (relatively) long time. This solves this.
- These timeout errors not only occur in the sending address part of
reading the uguru but also in the wait for read state, so errors in
this state are now handled as retryable just like send address state
errors and are only logged and reported to userspace if 3 executive
tries fail.
- Fix a very nasty bug in the bank1 sensor type detection code, where it
would not restore the original settings in any of the error paths!
- Since not successfully restoring the original settings can seriously
confuse the system BIOS (hang when entering the relevant setup menu),
we now try restoring them 3 times before giving up.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 11 Aug 2006 20:53:08 +0000 (22:53 +0200)]
[PATCH] i2c: tps65010 build fixes
The tps65010.c driver in the main tree never got updated with
build fixes since the last batch of I2C driver changes; and the
genirq trigger flags were updated wierdly too.
This also includes a minor tweak to reduce the frequency used to
poll for unplug-the-AC-power on the TPS chips that don't provide
relevant IRQs. It _would_ be nice to sense whether there's even
a battery, but that'd normally be an HDQ/1-wire interface to a
smart battery, and such APIs aren't standardized.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Christie [Sat, 26 Aug 2006 07:00:22 +0000 (03:00 -0400)]
[SCSI] fix scsi_send_eh_cmnd regression
The callers of scsi_send_eh_cmnd are setting the cmnd buffer,
and then scsi_send_eh_cmnd is copying that updated buffer to
the old_cmnd variable. Then after the command runs, we end up
copying that old_cmnd var which has the new cmnd to the scsi
command buffer. When this command gets recent, all types of fun
things happen like getting TUR or START_STOP commands with
data and scatterlists.
This patch made against scsi-rc-fixes, has the callers of
scsi_send_eh_cmnd pass in the command so scsi_send_eh_cmnd
can do the right thing. This should go into 2.6.18 since this
fixes a regression added when we removed some of the scsi_cmnd
fields and replaced them with local variables.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andrew Vasquez [Wed, 23 Aug 2006 21:54:54 +0000 (14:54 -0700)]
[SCSI] qla2xxx: Correct PLOGI retry logic.
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Douglas Gilbert [Sat, 19 Aug 2006 04:11:34 +0000 (00:11 -0400)]
[SCSI] sg: fix incorrect page problem
There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped. The fix is to
select the correct page by indexing into the compound.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Trond Myklebust [Wed, 23 Aug 2006 00:06:03 +0000 (20:06 -0400)]
VFS: Fix access("file", X_OK) in the presence of ACLs
Currently, the access() call will return incorrect information on NFS if
there exists an ACL that grants execute access to the user on a regular
file. The reason the information is incorrect is that the VFS overrides
this execute access in open_exec() by checking (inode->i_mode & 0111).
This patch propagates the VFS execute bit check back into the generic
permission() call.
Trond Myklebust [Thu, 24 Aug 2006 16:27:15 +0000 (12:27 -0400)]
NFSv4: Add v4 exception handling for the ACL functions.
This is needed in order to handle any NFS4ERR_DELAY errors that might be
returned by the server. It also ensures that we map the NFSv4 errors before
they are returned to userland.
David Howells [Thu, 24 Aug 2006 19:44:19 +0000 (15:44 -0400)]
NFS: Check lengths more thoroughly in NFS4 readdir XDR decode
Check the bounds of length specifiers more thoroughly in the XDR decoding of
NFS4 readdir reply data.
Currently, if the server returns a bitmap or attr length that causes the
current decode point pointer to wrap, this could go undetected (consider a
small "negative" length on a 32-bit machine).
Also add a check into the main XDR decode handler to make sure that the amount
of data is a multiple of four bytes (as specified by RFC-1014). This makes
sure that we can do u32* pointer subtraction in the NFS client without risking
an undefined result (the result is undefined if the pointers are not correctly
aligned with respect to one another).
Signed-Off-By: David Howells <dhowells@redhat.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 5861fddd64a7eaf7e8b1a9997455a24e7f688092 commit)
Neil Brown observed that the current limit of 32 bytes isn't enough to hold two
ip addresses and the rest of the stuff we're putting in it, so it's often
truncated to the point where it's unlikely to be unique. This can cause
spurious CLID_INUSE's from the server.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from fc8c17ec251e984ab3df9182ed097aa5b577c915 commit)
Chuck Lever [Wed, 23 Aug 2006 00:06:15 +0000 (20:06 -0400)]
SUNRPC: avoid choosing an IPMI port for RPC traffic
Some hardware uses port 664 for its hardware-based IPMI listener. Teach
the RPC client to avoid using that port by raising the default minimum port
number to 665.
Test plan:
Find a mainboard known to use port 664 for IPMI; enable IPMI; mount NFS
servers in a tight loop.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from 58e8cb3a035d22fc386e1c53a5d98c3f219530fb commit)
Trond Myklebust [Tue, 22 Aug 2006 17:44:32 +0000 (13:44 -0400)]
NFS: Fix issue with EIO on NFS read
The problem is that we may be caching writes that would extend the file and
create a hole in the region that we are reading. In this case, we need to
detect the eof from the server, ensure that we zero out the pages that
are part of the hole and mark them as up to date.
Trond Myklebust [Thu, 10 Aug 2006 15:58:57 +0000 (11:58 -0400)]
LOCKD: Fix a deadlock in nlm_traverse_files()
nlm_traverse_files() is not allowed to hold the nlm_file_mutex while calling
nlm_inspect file, since it may end up calling nlm_release_file() when
releaseing the blocks.
Trond Myklebust [Thu, 10 Aug 2006 21:51:46 +0000 (17:51 -0400)]
SUNRPC: rpc_unlink() must check for unhashed dentries
A prior call to rpc_depopulate() by rpc_rmdir() on the parent directory may
have already called simple_unlink() on this entry.
Add the same check to rpc_rmdir(). Also remove a redundant call to
rpc_close_pipes() in rpc_rmdir.
ASANO Masahiro [Wed, 23 Aug 2006 00:06:02 +0000 (20:06 -0400)]
VFS: add lookup hint for network file systems
I'm trying to speeding up mkdir(2) for network file systems. A typical
mkdir(2) calls two inode_operations: lookup and mkdir. The lookup
operation would fail with ENOENT in common case. I think it is unnecessary
because the subsequent mkdir operation can check it. In case of creat(2),
lookup operation is called with the LOOKUP_CREATE flag, so individual
filesystem can omit real lookup. e.g. nfs_lookup().
Here is a sample patch which uses LOOKUP_CREATE and O_EXCL on mkdir,
symlink and mknod. This uses the gadget for creat(2).
And here is the result of a benchmark on NFSv3.
mkdir(2) 10,000 times:
original 50.5 sec
patched 29.0 sec
Signed-off-by: ASANO Masahiro <masano@tnes.nec.co.jp> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
(cherry picked from fab7bf44449b29f9d5572a5dd8adcf7c91d5bf0f commit)
Nikita Danilov [Wed, 9 Aug 2006 17:53:47 +0000 (13:53 -0400)]
NFS: Fix a potential deadlock in nfs_release_page
nfs_wb_page() waits on request completion and, as a result, is not safe to be
called from nfs_release_page() invoked by VM scanner as part of GFP_NOFS
allocation. Fix possible deadlock by analyzing gfp mask and refusing to
release page if __GFP_FS is not set.
Tejun Heo [Tue, 22 Aug 2006 16:00:27 +0000 (01:00 +0900)]
[PATCH] sata_via: use old SCR access pattern on vt6420
vt6420 has super-fragile SCR registers which can hang the whole
machine if accessed with the wrong timings. This patch makes sata_via
use SCR registers only during probing and with the same timings as
before (pre new EH), which is proven to work.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements force_pcs module parameter for ata_piix. If 1,
PCS is ignored, 2 honored. As there seem to be quite a few ICHs w/
impaired PCS, this option will be useful for cases where the default
setting doesn't work.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 22 Aug 2006 12:06:46 +0000 (21:06 +0900)]
[PATCH] ata_piix: ignore PCS on ICH5
There have been a number of reports regarding some ICH5s failing to
detect devices since the PCS handling update. Analysis shows that
these problems are caused by bogus PCS values from those controllers.
Before the PCS update, the driver didn't honor PCS regs exactly and
probed them in many cases PCS reports no device. Now that PCS is
honored exactly, these hardware problems are visible.
This patch makes ICH5 ignore PCS.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don Fry [Tue, 22 Aug 2006 17:22:37 +0000 (10:22 -0700)]
[PATCH] pcnet32: break in 2.6.18-rc1 identified
A change I made for 2.6.17 and another for 2.6.18 do not work on older
pcnet32 chips which I do not have access to. If the chip is a 79C970 or
79C965, do not try and suspend or check the link status.
I have tested with a 79C970A, 79C971, 79C972, 79C973, 79C975, 79C976,
and 79C978.
Signed-off-by: Don Fry <brazilnut@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Joerg Ahrens [Sun, 20 Aug 2006 20:51:57 +0000 (21:51 +0100)]
[PATCH] xirc2ps_cs: Cannot reset card in atomic context
I am using a Xircom CEM33 pcmcia NIC which has occasional hardware problems.
If the netdev watchdog detects a transmit timeout, do_reset is called which
msleeps - this is illegal in atomic context.
This patch schedules the timeout handling as a workqueue item.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eric Sesterhenn [Sat, 19 Aug 2006 17:37:57 +0000 (19:37 +0200)]
[PATCH] Signedness issue in drivers/net/3c515.c
while playing with gcc 4.1 -Wextra warnings, I came across this one:
drivers/net/3c515.c:1027: warning: comparison of unsigned expression >= 0 is always true
Since i is unsigned the >= 0 check in the for loop is always true,
so we might spin there forever unless the if condition triggers.
Since i is only used in this loop, this patch changes it to
an integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adam Litke [Fri, 18 Aug 2006 18:22:21 +0000 (11:22 -0700)]
[POWERPC] hugepage BUG fix
On Tue, 2006-08-15 at 08:22 -0700, Dave Hansen wrote:
> kernel BUG in cache_free_debugcheck at mm/slab.c:2748!
Alright, this one is only triggered when slab debugging is enabled. The
slabs are assumed to be aligned on a HUGEPTE_TABLE_SIZE boundary. The free
path makes use of this assumption and uses the lowest nibble to pass around
an index into an array of kmem_cache pointers. With slab debugging turned
on, the slab is still aligned, but the "working" object pointer is not.
This would break the assumption above that a full nibble is available for
the PGF_CACHENUM_MASK.
The following patch reduces PGF_CACHENUM_MASK to cover only the two least
significant bits, which is enough to cover the current number of 4 pgtable
cache types. Then use this constant to mask out the appropriate part of
the huge pte pointer.
Signed-off-by: Adam Litke <agl@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Marc Zyngier [Wed, 23 Aug 2006 22:50:57 +0000 (15:50 -0700)]
[SERIAL] sunsab: Fix E250 console with RSC.
This fixes yet another sunsab problem, when console is set to anything
but the first port. The console framework calls sunsab_console_setup
for each port, and we end up setting up a console on a not yet
discovered port, which leads to an Oops. Instead, defer console setup
until the requested port is properly initialized. Tested on an E250
through an RSC console.
Reported by Daniel Smolik <marvin@mydatex.cz>
Signed-off-by: Marc Zyngier <maz@misterjones.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver's list of HCA firmware revisions to make sure people
running Sinai firmware older than 1.1.0 get a message suggesting a
firmware upgrade. Update the Arbel versions as well while we are at it.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Paul Mackerras [Wed, 23 Aug 2006 06:58:39 +0000 (16:58 +1000)]
[POWERPC] Correct masks used in emulating some instructions
When we get an illegal instruction exception, we check to see whether
the instruction is one that we emulate for the user program. Some of
the masks we use in checking whether the offending instruction is one
we care about didn't have the top bit set, which is the MSB of the
major opcode. Thus some undefined opcodes could get emulated as other
(defined but unimplemented) instructions. This corrects the masks.
The bootx_init.c trampoline didn't properly add the ramdisk to the
"reserve map" (list of reserved areas of memory), thus causing all sorts
of failures when using BootX with an initrd. Also fixes a possible
problem if the ramdisk is located before the device-tree passed by
BootX.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nathan Lynch [Wed, 23 Aug 2006 01:36:05 +0000 (20:36 -0500)]
[POWERPC] Fix gettimeofday inaccuracies
There are two problems in the powerpc gettimeofday code which can
cause incorrect results to be returned.
The first is that there is a race between do_gettimeofday and the
timer interrupt:
1. do_gettimeofday does get_tb()
2. decrementer exception on boot cpu which runs timer_recalc_offset,
which also samples the timebase and updates the do_gtod structure
with a greater timebase value.
3. do_gettimeofday calls __do_gettimeofday, which leads to the
negative result from tb_val - temp_varp->tb_orig_stamp.
The second is caused by taking the boot cpu offline, which can cause
the value of tb_last_jiffy to be increased past the currently
available timebase, causing the same underflow as above.
[paulus@samba.org - define and use data_barrier() instead of mb().]
Signed-off-by: Nathan Lynch <ntl@pobox.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jon Loeliger [Fri, 18 Aug 2006 19:30:35 +0000 (14:30 -0500)]
[POWERPC] Rewrite the PPC 86xx IRQ handling to use Flat Device Tree
IRQ setup now comes from the Flat Device Tree and use the new generic
IRQ code. Fixed the fsl_soc.c IRQ OF interrupt node parsing.
Removed some unused MPC86xx macro definition.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
(cherry picked from 919fede6edab94cccb3ca8c1c0b32fa62c9369a5 commit)
Andy Fleming [Fri, 18 Aug 2006 01:24:48 +0000 (20:24 -0500)]
[POWERPC] Fix CDS IRQ handling and PCI code
* Fix IRQ support in the 85xx CDS boards so it uses the new
generic stuff
* Fix PCI IRQ mapping to use the device tree
* Disabled i8259 support to allow the CDS to boot. This will be
fixed soon, but the current code doesn't even compile, so this
is a vast improvement
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andy Fleming [Fri, 18 Aug 2006 23:03:08 +0000 (18:03 -0500)]
[POWERPC] Fix interrupts on 8540 ADS board
* Fixed 8540 ADS support for the new irq layer
* Fixed 8540 ADS support for mapping PCI interrupts
* Updated 8540 ADS to use device tree for interrupt assignment
and sense values
Michael Rash [Tue, 22 Aug 2006 07:45:22 +0000 (00:45 -0700)]
[TEXTSEARCH]: Fix Boyer Moore initialization bug
The pattern is set after trying to compute the prefix table, which tries
to use it. Initialize it before calling compute_prefix_tbl, make
compute_prefix_tbl consistently use only the data from struct ts_bm
and remove the now unnecessary arguments.
Signed-off-by: Michael Rash <mbr@cipherdyne.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This small change allows for easy per-route workarounds for broken hosts or
middleboxes that are not compliant with TCP standards for window scaling.
Rather than having to turn off window scaling globally. This patch allows
reducing or disabling window scaling if window clamp is present.
Example: Mark Lord reported a problem with 2.6.17 kernel being unable to
access http://www.everymac.com
# ip route add 216.145.246.23/32 via 10.8.0.1 window 65535
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_make_abort_user() now takes the msg_len along with the msg
so that we don't have to recalculate the bytes in iovec.
It also uses memcpy_fromiovec() so that we don't go beyond the
length allocated.
It is good to have this fix even if verify_iovec() is fixed to
return error on overflow.
Move out PCS handling from piix_sata_prereset() into
piix_sata_present_mask() and use it from newly implemented
piix_sata_softreset(). Class codes for devices which are indicated to
be absent by PCS are cleared to ATA_DEV_NONE. This fixes ghost device
problem reported on ICH6 and 7.
This patch moves PCS handling from prereset to softreset, which makes
two behavior changes.
* perform softreset even when PCS indicates no device
* PCS handling is repeated before retrying softresets due to reset
failures.
Both behavior changes are intended and more consistent with how other
drivers behave.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Oleg Nesterov [Mon, 21 Aug 2006 06:34:15 +0000 (08:34 +0200)]
[PATCH] Fix current_io_context() vs set_task_ioprio() race
I know nothing about io scheduler, but I suspect set_task_ioprio() is not safe.
current_io_context() initializes "struct io_context", then sets ->io_context.
set_task_ioprio() running on another cpu may see the changes out of order, so
->set_ioprio(ioc) may use io_context which was not initialized properly.
Vitaly Bordug [Tue, 15 Aug 2006 06:00:31 +0000 (23:00 -0700)]
[PATCH] ppc32: board-specific part of fs_enet update
This contains board-specific portion to respect driver changes (for 8272ads ,
885ads and 866ads). Altered platform_data structures as well as initial setup
routines relevant to fs_enet.
Changes to the mpc8560ads ppc/ code are also introduced, but mainly as
reference, since the entire board support is going to appear in arch/powerpc.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Vitaly Bordug [Tue, 15 Aug 2006 06:00:30 +0000 (23:00 -0700)]
[PATCH] FS_ENET: use PAL for mii management
This patch should update the fs_enet infrastructure to utilize Phy Abstraction
Layer subsystem. Along with the above, there are apparent bugfixes, overhaul
and improvements.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Vitaly Bordug [Tue, 15 Aug 2006 06:00:29 +0000 (23:00 -0700)]
[PATCH] PAL: Support of the fixed PHY
This makes it possible for HW PHY-less boards to utilize PAL goodies. Generic
routines to connect to fixed PHY are provided, as well as ability to specify
software callback that fills up link, speed, etc. information into PHY
descriptor (the latter feature not tested so far).
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] skge: remember to run netif_poll_disable()
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@axis.com> Cc: Stephen Hemminger <shemminger@osdl.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
David Brownell [Tue, 15 Aug 2006 06:00:22 +0000 (23:00 -0700)]
[PATCH] build fixes: smc91x
Unclear how these bugs arrived, presumably from incorrect cleanup of
the 16-bit-only paths, but smc91x wouldn't build for OMAP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Nicolas Pitre <nico@cam.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Roger Luethi [Tue, 15 Aug 2006 06:00:21 +0000 (23:00 -0700)]
[PATCH] via-rhine: add option avoid_D3 (work around broken BIOSes)
It looks like broken BIOSes controlling Rhine chips will remain in use in
significant numbers; such systems fail to come up via PXE after they have
been put into D3 (power-saving) mode.
This patch adds a module option for disabling the call that puts the chip
to sleep.
Signed-off-by: Roger Luethi <rl@hellgate.ch> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Joerg Bashir <brak@archive.org> Cc: Tim Phipps <tim@phipps-hutton.freeserve.co.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Russell King [Tue, 15 Aug 2006 06:00:20 +0000 (23:00 -0700)]
[PATCH] lockdep: fix smc91x
When booting using root-nfs, I'm seeing (independently) two lockdep dumps
in the smc91x driver. The patch below fixes both. Both dumps look like
real locking issues.
Nico - please review and ack if you think the patch is correct.
The poll_enable should be in init_registers before enabling interrupts, not
in tx_timeout. Thanks for spotting it Roger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Cc: Roger Luethi <rl@hellgate.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Roger Luethi [Tue, 15 Aug 2006 06:00:17 +0000 (23:00 -0700)]
[PATCH] via-rhine: NAPI support
Add NAPI support to the via-rhine driver so that it can handle higher
speeds and doesn't get overloaded by interrupts as easily.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Roger Luethi <rl@hellgate.ch> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Peter Korsgaard [Tue, 15 Aug 2006 06:00:17 +0000 (23:00 -0700)]
[PATCH] smc911x: Re-release spinlock on spurious interrupt
The smc911x driver forgets to release the spinlock on spurious interrupts.
This little patch fixes it.
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kevin Hao [Tue, 15 Aug 2006 06:00:15 +0000 (23:00 -0700)]
[PATCH] net: Add netconsole support to dm9000 driver
Add netconsole support to dm9000 driver.
Cc: Jeff Garzik <jeff@garzik.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Tue, 15 Aug 2006 06:00:14 +0000 (23:00 -0700)]
[PATCH] s2io build fix
sparc32:
drivers/net/s2io.c:2636: warning: implicit declaration of function 'disable_irq'
drivers/net/s2io.c:2656: warning: implicit declaration of function 'enable_irq'
Cc: Ananda Raju <Ananda.Raju@neterion.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Deepak Saxena [Tue, 15 Aug 2006 06:00:13 +0000 (23:00 -0700)]
[PATCH] Update smc91x driver with ARM Versatile board info
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Cc: Jeff Garzik <jeff@garzik.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Nicolas Pitre <nico@cam.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Li Yang [Tue, 15 Aug 2006 06:00:11 +0000 (23:00 -0700)]
[PATCH] Freescale QE UCC gigabit ethernet driver
QE(QUICC Engine) is a new generation communication coprocessor, which can
be found on some of the latest Freescale PowerQUICC CPUs(e.g. MPC8360).
The UCC(Unified Communications Controller) module of QE can work as gigabit
Ethernet device. This patch provides driver for the device.
Signed-off-by: Shlomi Gridish <gridish@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Tue, 15 Aug 2006 06:00:10 +0000 (23:00 -0700)]
[PATCH] sundance section fix
drivers/net/sundance.c:110: error: version causes a section type conflict
I don't understand this error. It's referred to from both __init and
__devinit code. With CONFIG_HOTPLUG=n, version[] is placed in .init.data and
is referred to from .init.text.
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Tue, 15 Aug 2006 06:00:08 +0000 (23:00 -0700)]
[PATCH] seeq8005 section fix
WARNING: drivers/net/seeq8005.o - Section mismatch: reference to .init.text:seeq8005_probe from .text between 'init_module' (at offset 0x106) and 'seeq8005_open'
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / linux-2.6-omap-h63xx.git / log