Anton Vorontsov [Thu, 13 Sep 2007 15:23:33 +0000 (19:23 +0400)]
ucc_geth: fix compilation
Currently qe_bd_t is used in the macro call -- dma_unmap_single,
which is a no-op on PPC32, thus error is hidden today. Starting
with 2.6.24, macro will be replaced by the empty static function,
and erroneous use of qe_bd_t will trigger compilation error.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Larry Finger [Tue, 4 Sep 2007 19:14:20 +0000 (14:14 -0500)]
[PATCH] bcm43xx: Fix cancellation of work queue crashes
A crash upon booting that is caused by bcm43xx has been reported [1] and
found to be due to a work queue being reinitialized while work on that
queue is still pending. This fix modifies the shutdown of work queues and
prevents periodic work from being requeued during shutdown. With this patch,
no more crashes on reboot were observed by the original reporter. I do not
get that particular failure on my system; however, when running a large
number of ifdown/ifup sequences, my system would kernel panic with the
'caps lock' light blinking at roughly a 1 Hz rate. In addition, there were
infrequent failures in the firmware that resulted in 'IRQ READY TIMEOUT'
errors. With this patch, no more of the first type of failure occur, and
incidence of the second type is greatly reduced.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ishizaki Kou [Mon, 20 Aug 2007 13:13:27 +0000 (22:13 +0900)]
spidernet: fix interrupt reason recognition
This patch solves a problem that the spidernet driver sometimes fails
to handle IRQ.
The problem happens because,
- In Cell architecture, interrupts may arrive at an interrupt
controller, even if they are masked by the setting on registers of
devices. It happens when interrupt packets are sent just before
the interrupts are masked.
- spidernet interrupt handler compares interrupt reasons with
interrupt masks, so when such interrupts occurs, spidernet interrupt
handler returns IRQ_NONE.
- When all of interrupt handler return IRQ_NONE, linux kernel disables
the IRQ and it no longer delivers interrupts to the interrupt handlers.
spidernet doesn't work after above sequence, because it can't receive
interrupts.
This patch changes spidernet interrupt handler that it compares
interrupt reason with SPIDER_NET_INTX_MASK_VALUE.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduces a module parameter to decide whether the physical
port link state is propagated to the network stack or not.
It makes sense not to take the physical port state into account
on machines with more logical partitions that communicate
with each other. This is always possible no matter what the physical
port state is. Thus eHEA can be considered as a switch there.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
64-bit DMA causes data corruption with atl1. We don't know why, and Atheros
is working on it. For now, just use 32-bit DMA. This is a big hack that is
probably wrong, but it stops the bleeding.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com> Acked-by: Chris Snook <csnook@redhat.com> Acked-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Olof Johansson [Thu, 23 Aug 2007 00:26:37 +0000 (19:26 -0500)]
[POWERPC] Move serial_dev_init to device_initcall()
With the I/O space rewrite by BenH, the legacy_serial serial_dev_init()
initcall is now called before I/O space is setup, but it's dependent on
it being available.
Since there's no way to make dependencies between initcalls, we'll just
have to move it to device_initcall(). Yes, it's suboptimal but I'm not
aware of any better solution at this time, and it fixes a regression
from 2.6.22.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a compile error when the directory above the kernel source contains
a file named "kernel". Originally from Ben LaHaise, modified based on
feedback from Sam Ravnborg
Signed-off-by: Andi Kleen <ak@suse.de> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Ben LaHaise <bcrl@kvack.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mackerras [Wed, 12 Sep 2007 15:16:31 +0000 (01:16 +1000)]
Define termios_1 functions for powerpc, s390, avr32 and frv
Commit f629307c857c030d5a3dd777fee37c8bb395e171 introduced uses of
kernel_termios_to_user_termios_1 and user_termios_to_kernel_termios_1
on all architectures. However, powerpc, s390, avr32 and frv don't
currently define those functions since their termios struct didn't
need to be changed when the arbitrary baud rate stuff was added, and
thus the kernel won't currently build on those architectures.
This adds definitions of kernel_termios_to_user_termios_1 and
user_termios_to_kernel_termios_1 to include/asm-generic/termios.h
which are identical to kernel_termios_to_user_termios and
user_termios_to_kernel_termios respectively. The definitions are the
same because the "old" termios and "new" termios are in fact the same
on these architectures (which are the same ones that use
asm-generic/termios.h).
Signed-off-by: Paul Mackerras <paulus@samba.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Alan Cox <alan@redhat.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kumar Gala [Mon, 10 Sep 2007 19:57:34 +0000 (14:57 -0500)]
[POWERPC] Enable GENERIC_ISA_DMA if FSL_ULI1575 to fix compile issue
Since the ULI1575 has a ISA bus we need to enable the generic ISA dma
support for drivers that might expect it. Without this we get compile
errors like the following:
ound/built-in.o: In function `claim_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
sound/built-in.o: In function `release_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:195: undefined reference to `dma_spin_lock'
sound/built-in.o: In function `claim_dma_lock':
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
/home/galak/git/linux-8572/include/asm/dma.h:189: undefined reference to `dma_spin_lock'
sound/built-in.o:/home/galak/git/linux-8572/include/asm/dma.h:195: more undefined references to `dma_spin_lock' follow
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Fix calculation of i_blocks during truncate
[PATCH] ocfs2: Fix a wrong cluster calculation.
[PATCH] ocfs2: fix mount option parsing
ocfs2: update docs for new features
Adrian Bunk [Tue, 11 Sep 2007 22:24:13 +0000 (15:24 -0700)]
fix SERIAL_CORE_CONSOLE driver dependencies
SERIAL_BFIN=m or SERIAL_MUX=m shouldn't allow SERIAL_CORE_CONSOLE=y.
Additionally, this patch fixes whitespace instead of tabs at the
SERIAL_MUX_CONSOLE option.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Bryan Wu <bryan.wu@analog.com> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pixel clock (and thus both H and V sync) will be slower than requested, so
if you set the minimum allowed the display may not sync. In case of really
old CRT display it could theoretically damage it.
I'm using it with PAL TV (using RGB input - SCART connector) and the bug
prevented it from working at all (TV requirements are more strict and made the
bug visible).
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we simply add the debug flags unconditional when checking for a
matching slab. This creates issues for sysfs processing when slabs exist
that are exempt from debugging due to their huge size or because only a
subset of slabs was selected for debugging.
We need to only add the flags if kmem_cache_open() would also add them.
Create a function to calculate the flags that would be set
if the cache would be opened and use that function to determine
the flags before looking for a compatible slab.
[akpm@linux-foundation.org: fixlets] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Chuck Ebbert <cebbert@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Catch illegally nested kmap_atomic()s even if the page that is mapped by
the 'inner' instance is from lowmem.
This avoids spuriously zapped kmap-atomic ptes and turns hard to find
crashes into clear asserts at the bug site.
Problem is, a get_zeroed_page(GFP_KERNEL) from interrupt context will trigger
this check if non-irq code on this CPU holds a KM_USER0 mapping. But that
get_zeroed_page() will never be altering the kmap slot anyway due to the
GFP_KERNEL.
Cc: Christoph Lameter <clameter@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Emelyanov [Tue, 11 Sep 2007 22:24:01 +0000 (15:24 -0700)]
Leases can be hidden by flocks
The inode->i_flock list contains the leases, flocks and posix
locks in the specified order. However, the flocks are added in
the head of this list thus hiding the leases from F_GETLEASE
command, from time_out_leases() and other code that expects
the leases to come first.
Zhenyu Wang [Tue, 11 Sep 2007 22:23:58 +0000 (15:23 -0700)]
intel_agp: fix GTT map size on G33
G33 has 1MB GTT table range. Fix GTT mapping in case like 512MB aperture
size.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com> Acked-by: Dave Airlie <airlied@linux.ie> Cc: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhenyu Wang [Tue, 11 Sep 2007 22:23:57 +0000 (15:23 -0700)]
intel_agp: fix stolen mem range on G33
G33 GTT stolen memory is below graphics data stolen memory and be seperate,
so don't subtract it in stolen mem counting.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com> Acked-by: Dave Airlie <airlied@linux.ie> Cc: Dave Jones <davej@codemonkey.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taneli Vähäkangas <vahakang@cs.helsinki.fi> reported that commit 786d7e1612f0b0adb6046f19b906609e4fe8b1ba aka "Fix rmmod/read/write races
in /proc entries" broke SBCL + SLIME combo.
The old code in do_select() used DEFAULT_POLLMASK, if couldn't find
->poll handler. The new code makes ->poll always there and returns 0 by
default, which is not correct. Return DEFAULT_POLLMASK instead.
Steps to reproduce:
install emacs, SBCL, SLIME
emacs
M-x slime in *inferior-lisp* buffer
[watch it doing "Connecting to Swank on port X.."]
Please, apply before 2.6.23.
P.S.: why SBCL can't just read(2) /proc/cpuinfo is a mystery.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: T Taneli Vahakangas <vahakang@cs.helsinki.fi> Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Ellerman [Tue, 11 Sep 2007 22:23:51 +0000 (15:23 -0700)]
Restore call_usermodehelper_pipe() behaviour
The semantics of call_usermodehelper_pipe() used to be that it would fork
the helper, and wait for the kernel thread to be started. This was
implemented by setting sub_info.wait to 0 (implicitly), and doing a
wait_for_completion().
As part of the cleanup done in 0ab4dc92278a0f3816e486d6350c6652a72e06c8,
call_usermodehelper_pipe() was changed to pass 1 as the value for wait to
call_usermodehelper_exec().
This is equivalent to setting sub_info.wait to 1, which is a change from
the previous behaviour. Using 1 instead of 0 causes
__call_usermodehelper() to start the kernel thread running
wait_for_helper(), rather than directly calling ____call_usermodehelper().
The end result is that the calling kernel code blocks until the user mode
helper finishes. As the helper is expecting input on stdin, and now no one
is writing anything, everything locks up (observed in do_coredump).
The fix is to change the 1 to UMH_WAIT_EXEC (aka 0), indicating that we
want to wait for the kernel thread to be started, but not for the helper to
finish.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller [Tue, 11 Sep 2007 22:23:50 +0000 (15:23 -0700)]
tty: termios locking functions break with new termios type
I ran into a few problems.
n_tty_ioctl() for instance:
drivers/char/tty_ioctl.c:799: error: $,1rxstruct termios$,1ry has no
member named $,1rxc_ispeed$,1ry
This is calling the copy interface that is supposed to be using
a termios2 when the new interfaces are defined, however:
case TIOCGLCKTRMIOS:
if (kernel_termios_to_user_termios((struct termios __user *)arg, real_tty->termios_locked))
return -EFAULT;
return 0;
This is going to write over the end of the userspace
structure by a few bytes, and wasn't caught by you yet
because the i386 implementation is simply copy_to_user()
which does zero type checking.
Signed-off-by: Alan Cox <alan@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The futex list traversal on the compat side appears to have
a bug.
It's loop termination condition compares:
while (compat_ptr(uentry) != &head->list)
But that can't be right because "uentry" has the special
"pi" indicator bit still potentially set at bit 0. This
is cleared by fetch_robust_entry() into the "entry"
return value.
What this seems to mean is that the list won't terminate
when list iteration gets back to the the head. And we'll
also process the list head like a normal entry, which could
cause all kinds of problems.
So we should check for equality with "entry". That pointer
is of the non-compat type so we have to do a little casting
to keep the compiler and sparse happy.
The same problem can in theory occur with the 'pending'
variable, although that has not been reported from users
so far.
Based on the original patch from David Miller.
Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: David Miller <davem@davemloft.net> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthew Wilcox [Tue, 11 Sep 2007 22:23:47 +0000 (15:23 -0700)]
PTR_ALIGN
The AdvanSys driver wants to align some pointers, and the ALIGN macro
doesn't work for pointers. Rather than try to make it work, add a new
PTR_ALIGN macro which is typesafe.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Acked-by: Satyam Sharma <satyam@infradead.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md: fix some bugs with growing raid5/raid6 arrays.
The recent changed to raid5 to allow offload of parity calculation etc
introduced some bugs in the code for growing (i.e. adding a disk to) raid5
and raid6. This fixes them
Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the quirk enables the SIR part of the SMCf010 device, the 8250 driver
may claim it as a legacy ttyS device, which makes the legacy probe in the
smsc-ircc2 driver fail.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Andrey Borzenkov <arvidjaar@mail.ru> Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Andersson [Tue, 11 Sep 2007 22:23:30 +0000 (15:23 -0700)]
spi_mpc83xx: hang fix
When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it
only writes one zero filled word to the transmit register. If the driver
expects to receive more than one word it will wait forever for a second
receive interrupt. With this patch the controller will shift out zeroes
until all words have been received.
Signed-off-by: Jan Andersson <jan@gaisler.com> Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Tue, 11 Sep 2007 22:23:29 +0000 (15:23 -0700)]
quota: fix infinite loop
If we fail to start a transaction when releasing dquot, we have to call
dquot_release() anyway to mark dquot structure as inactive. Otherwise we
end in an infinite loop inside dqput().
Signed-off-by: Jan Kara <jack@suse.cz> Cc: xb <xavier.bru@bull.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix aliasing bug in copy_user_highpage.
[MIPS] IP22: fix wrong argument order
[MIPS] IP22: Fix wrong check for second HPC
[MIPS] Ocelot: remove remaining bits
[MIPS] TLB: Fix instruction bitmasks
[MIPS] R10000: Fix wrong test in dma-default.c
[MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
[MIPS] Sibyte: Remove broken dependency on EXPERIMENTAL from SIBYTE_SB1xxx_SOC.
[MIPS] Kconfig: whitespace cleanup.
[MIPS] PCI: Set need_domain_info if controller domain index is non-zero.
[MIPS] BCM1480: Fix computation of interrupt mask address register.
[MIPS] i8259: Add disable method.
[MIPS] tty: add the new ioctls and definitions.
Fix a bitmask typo in the pdc202xx_new PLL frequency detection code
which causes it to truncate an intermediate difference to 26 bits
instead of the correct 30 bits (the PLL's bitwidth).
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Daniel Exner [Tue, 11 Sep 2007 20:28:36 +0000 (22:28 +0200)]
pata_ali/alim15x3: override 80-wire cable detection for Toshiba S1800-814
Add Toshiba S1800-814 to whitelist for both pata_ali and alim15x3,
as it is correctly detected as 40-wire connected but this cable is
short enough to still use transfer modes higher than UDMA33.
Signed-off-by: Daniel Exner <dex@dragonslave.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 11 Sep 2007 20:28:36 +0000 (22:28 +0200)]
hpt366: UltraDMA filter for SATA cards (take 2)
The Marvell bridge chips used on HighPoint SATA cards do not seem to support
the UltraDMA modes 1, 2, and 3 as well as any MWDMA modes, so the driver needs
to account for this in the udma_filter() method. In order to achieve that, do
the following changes:
- install the method for all chips, not only HPT36x/370 and improve the code
formatting by killing the extra tabs while at it;
- add to the end of the 'switch' statement in the method cases for HPT372[AN]
and HPT374 chips upon which the known SATA cards are based;
- use hwif->ultra_mask as a default mask for the ide_dma_filter() method to
behave correctly;
- move the HPT370[A] cases below the HPT36x case for consistency.
While at it, replace the explicit UltraDMA mode masks with ATA_UDMA* constants
all over the driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Bob Ham <rah@bash.sh> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 11 Sep 2007 20:28:36 +0000 (22:28 +0200)]
ide: add ide_dev_is_sata() helper (take 2)
Make the SATA drive detection code from eighty_ninty_three() into inline
ide_dev_is_sata() helper fixing it along the way to be more strict while
checking word 80 for the reserved values...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 11 Sep 2007 20:28:35 +0000 (22:28 +0200)]
hpt366: fix PCI clock detection for HPT374 (take 4)
HPT374 BIOS seems to only save f_CNT register value for the function #0 before
re-tuning DPLL (that causes the driver to report obviously distorted f_CNT for
the function #1) -- fix this by always reading the saved f_CNT register value
from the function #0 in the driver's init_chipset() method.
While at it, introduce 'chip_type' for holding the 'struct hpt_info' field
of the same name and replace the structure assignment with memcpy()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 11 Sep 2007 20:28:34 +0000 (22:28 +0200)]
pdc202xx_new: fix PCI refcounting
The driver erroneously "lets go" the mate IDE chip in init_setup_pdc20270()
when ide_setup_pci_devices() call succeeds -- fix this, and drop a couple of
useless assignments in this function while at it...
Bart: keep "findev" variable initialization to silence gcc
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Tue, 11 Sep 2007 20:28:34 +0000 (22:28 +0200)]
ide: fix PCI refcounting
The IDE core never marked the PCI IDE devices as being in use after succesfull
driver probe call (the devices were marked in use only while being probed), and
so was susceptible to issues caused by unsolicited PCI hotplug device removal.
So, add pci_dev_get() call to ide_scan_pcidev() and convert this function to
the kernel style, also dropping a bunch of useless curly braces from its caller,
ide_scan_pcibus() and somewhat beautifying printk() call there, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Kumar Gala [Tue, 11 Sep 2007 20:28:33 +0000 (22:28 +0200)]
mpc8xx: Only build mpc8xx on arch/ppc
Currently the mpc8xx ide driver will only work on arch/ppc so only
allow it to be built there. Also, killed a minor include that isn't
actually used by the driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ocfs2_alloc_write_write_ctxt, the written clusters length is calculated
by the byte length only. This may cause some problems if we start to write
at some position in the end of one cluster and last to a second cluster
while the "len" is smaller than a cluster size. In that case, we have to
write 2 clusters actually.
So we have to take the start position into consideration also.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Tiger Yang [Fri, 7 Sep 2007 16:16:10 +0000 (00:16 +0800)]
[PATCH] ocfs2: fix mount option parsing
For some mount option types, ocfs2_parse_options() will try to access
sb->s_fs_info to get at the ocfs2 private superblock. Unfortunately, that
hasn't been allocated yet and will cause a kernel crash.
Fix this by storing options in a struct which can then get pushed into the
ocfs2_super once it's been allocated later. If we need more options which
store to the ocfs2_super in the future, we can just fields to this struct.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Mark Fasheh [Thu, 23 Aug 2007 18:17:55 +0000 (11:17 -0700)]
ocfs2: update docs for new features
Update documentation listing ocfs2 features to reflect the current state of
the file system. Add missing descriptions for some mount options which ocfs2
supports.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Copy_user_highpage was written assuming it was only being called for
breaking COW pages in which case the source page isn't cached as in
marked cachable under it kernel virtual address. If it is called anyway
the aliasing avoidance strategy implemented by kmap_coherent will fail.
Avoid the use of kmap_coherent for pages marked dirty and to avoid
another instance of this sort of bug, place a BUG_ON in kmap_coherent.
[MIPS] Provide empty irq_enable_hazard definition for legacy and R1 cores.
Following a strict interpretation the empty definition of irq_enable_hazard
has always been a bug - but an intentional one because it didn't bite.
This has now changed, for uniprocessor kernels mm/slab.c:do_drain()
Ralf Baechle [Tue, 28 Aug 2007 23:38:13 +0000 (00:38 +0100)]
[MIPS] BCM1480: Fix computation of interrupt mask address register.
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_mask_irq':
arch/mips/sibyte/bcm1480/irq.c:112: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:114: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c: In function 'bcm1480_unmask_irq':
arch/mips/sibyte/bcm1480/irq.c:130: warning: cast to pointer from integer of different size
arch/mips/sibyte/bcm1480/irq.c:132: warning: cast to pointer from integer of different size
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: irq and pci_ids patch for Intel Tolapai
PCI: unhide SMBus on Compaq Deskpro EP 401963-001 motherboard
PCI: Remove __devinit from pcibios_get_irq_routing_table
PCI: remove devinit from pci_read_bridge_bases
PCI AER: fix warnings when PCIEAER=n
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: drivers/usb/serial/bus.c: Fix incompatible pointer type warning
USB: another quirky device (LCD display)
USB: fix serial gadget ACM breakage
USB: More USB_QUIRK_RESET_RESUME devices
USB Mass Storage: limit "Rockchip ROCK MP3" device (071b:3203) max I/O to 64 sectors per command
USB: Nikon D40 Quirks
USB: Add Sony Ericsson P1i to unusual_devs.h
USB: option: Add Dell HSDPA 5520 to driver
USB: option: Add a new device ID for the HUAWEI E220 HSDPA modem.
USB: fix linked list insertion bugfix for usb core
USB: quirky flash drive
USB: prevent Genesys USB-IDE from autosuspending
USB: prevent Thomson card reader from autosuspending
USB: Add iPhone device id to the quirk list.
USB: ftdi_sio: add of a new product/manufacturer, TML
usb/misc/sisusbvga: add product ID of TARGUS/MCT device
USB: oti6858: Remove broken ioctl code in -mm tree and also the broken fixes
Anti Sullin [Thu, 30 Aug 2007 14:15:16 +0000 (16:15 +0200)]
bug in AT91 MCI suspend routines
This patch fixes a bug in AT91 mmc host driver, that enables the wakeup
from suspend on card detection pin even if the card detect pin is not
available (==0). If not card detection pin is defined, IRQ0 == FIQ gets
enabled and if some activity is present on that pin, the system gets a
FIQ request, that causes a crash.
Signed-off-by: Anti Sullin <anti.sullin@artecdesign.ee> Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
USB: drivers/usb/serial/bus.c: Fix incompatible pointer type warning
drivers/usb/serial/bus.c: In function usb_serial_bus_deregister:
drivers/usb/serial/bus.c:185:
warning: passing argument 1 of free_dynids from incompatible pointer type
Above build warning comes when CONFIG_HOTPLUG=n because argument of
free_dynids() in serial/bus.c is a struct usb_serial_driver, not a
struct usb_driver. This is not a runtime bug, because the function
is an empty stub and never dereferences the passed pointer anyway.
David Brownell [Sun, 26 Aug 2007 19:44:24 +0000 (12:44 -0700)]
USB: fix serial gadget ACM breakage
Two of the CDC ACM control requests in the serial gadget have never
been correct, and have been reported to cause serious troubles ... as
in, soft lockup and maybe watchdog reset (depending on hardware).
This patch makes those request fail cleanly, rather than misbehaving.
Someone using CDC ACM should fix them according to the FIXME comments
which now replace the previous bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.
USB Mass Storage: limit "Rockchip ROCK MP3" device (071b:3203) max I/O to 64 sectors per command
The MP3/MP4/AVI player "Rockchip ROCK MP3" is seen as a USB disk, but fails
if more than 128 sectors (64kB) are sent or requested in a single read or write
command, and disconnects from the USB bus.
Typical kernel log showing the problem is:
usb 3-1: reset high speed USB device using ehci_hcd and address 6
usb 3-1: reset high speed USB device using ehci_hcd and address 6
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
sd 14:0:0:0: [sdb] Result: hostbyte=0x07 driverbyte=0x00
end_request: I/O error, dev sdb, sector 32
usb 3-1: USB disconnect, address 6
This patch works around the device limitation by adding "Rockchip ROCK MP3"
to unusual USB devices list and limiting data transfers to 64 sectors (32kB)
per command.
Tested on 2.6.23-rc5 (amd64).
projects / linux-2.6-omap-h63xx.git / log