[PATCH] cciss: add struct pci_driver shutdown support (replaces reboot notifier)
This patch adds support for the struct pci_driver shutdown method to cciss.
We require notification of an impending reboot or shutdown so that we can
flush the battery backed write cache (BBWC) on the Smart Array controller.
Signed-off-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the way we determine if a logical volume is larger than
2TB.
The original test looked for a total_size of 0. Originally we added 1 to the
total_size. That would make our read_capacity return size 0 for >2TB lv's.
We assumed that we could not have a lv size of 0 so it seemed OK until we were
in a clustered system. The backup node would see a size of 0 due to the
reservation on the drive. That caused the driver to switch to 16-byte CDB's
which are not supported on older controllers. After that everything was
broken.
It may seem petty but I don't see the value in trying to determine if the LBA
is beyond the 2TB boundary. That's why when we switch we use 16-byte CDB's
for all read/write operations. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Josh Triplett [Tue, 6 Mar 2007 09:42:13 +0000 (01:42 -0800)]
[PATCH] Publish rcutorture module parameters via sysfs, read-only
rcutorture's module parameters currently use permissions of 0, so they
don't show up in /sys/module/rcutorture/parameters. Change the permissions
on all module parameters to world-readable (0444).
rcutorture does all of its initialization and thread startup when loaded
and relies on the parameters not changing during execution, so they should
not permit writing. However, reading seems fine.
Signed-off-by: Josh Triplett <josh@freedesktop.org> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Walker [Tue, 6 Mar 2007 09:42:11 +0000 (01:42 -0800)]
[PATCH] fix vsyscall settimeofday
I've only seen this on x86_64.
The vsyscall state only gets updated when a timer interrupts comes in. So
if the time is set long before the next timer, there will be a period when
a gettimeofday() won't reflect the correct time.
I added an explicit update_vsyscall() during the settimeofday(), that way
the vsyscall state doesn't get stale.
Signed-off-by: Daniel Walker <dwalker@mvista.com> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: John Stultz <johnstul@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Tue, 6 Mar 2007 09:42:08 +0000 (01:42 -0800)]
[PATCH] highres: do not run the TIMER_SOFTIRQ after switching to highres mode
The TIMER_SOFTIRQ runs the hrtimers during bootup until a usable
clocksource and clock event sources are registered. The switch to high
resolution mode happens inside of the TIMER_SOFTIRQ, but runs the softirq
afterwards. That way the tick emulation timer, which was set up in the
switch to highres might be executed in the softirq context, which is a BUG.
The rbtree has not to be touched by the softirq after the highres switch.
This BUG was observed by Andres Salomon, who provided the information to
debug it.
Return early from the softirq, when the switch was sucessful.
[dilinger@debian.org: add debug warning]
[akpm@linux-foundation.org: make debug warning compile] Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andres Salomon <dilinger@debian.org> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andres Salomon <dilinger@debian.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Tue, 6 Mar 2007 09:42:05 +0000 (01:42 -0800)]
[PATCH] i386: make x86_64 tsc header require i386 rather than vice-versa
Prior to commit 95492e4646e5de8b43d9a7908d6177fb737b61f0 ([PATCH] x86:
rewrite SMP TSC sync code), the headers in asm-i386 did not really require
anything in include/asm-x86_64. This means that distributions such as
fedora did not include asm-x86_64 in kernel-devel headers for i386. Ingo's
commit changed that, and broke things. This is easy enough to hack around
in package builds by just including asm-x86_64 on i386, but that's kind of
annoying. If anything, x86_64 should depend upon i386, not the other way
around.
This patch changes it so that asm-x86_64/tsc.h includes asm-i386/tsc.h,
rather than vice-versa.
Signed-off-by: Andres Salomon <dilinger@debian.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Lord [Tue, 6 Mar 2007 09:42:03 +0000 (01:42 -0800)]
[PATCH] Fix 2.6.21 rfcomm lockups
Any attempt to open/use a bluetooth rfcomm device locks up
scheduling completely on my machine.
Interrupts (ping, alt-sysrq) seem to be alive, but nothing else.
This was working fine in 2.6.20, broken now in 2.6.21-rc2-git*
Reverting this change (below) fixes it:
| author Marcel Holtmann <marcel@holtmann.org>
| Sat, 17 Feb 2007 22:58:57 +0000 (23:58 +0100)
| committer David S. Miller <davem@sunset.davemloft.net>
| Mon, 26 Feb 2007 19:42:41 +0000 (11:42 -0800)
| commit c1a3313698895d8ad4760f98642007bf236af2e8
| tree 337a876f727061362b6a169f8759849c105b8f7a tree | snapshot
| parent f5ffd4620aba9e55656483ae1ef5c79ba81f5403 commit | diff
| | [Bluetooth] Make use of device_move() for RFCOMM TTY devices
| | In the case of bound RFCOMM TTY devices the parent is not available
| before its usage. So when opening a RFCOMM TTY device, move it to
| the corresponding ACL device as a child. When closing the device,
| move it back to the virtual device tree.
| Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The simplest fix for this bug is to prevent sysfs_move_dir()
from self-deadlocking when (old_parent == new_parent).
This patch prevents total system lockup when using rfcomm devices.
Signed-off-by: Mark Lord <mlord@pobox.com> Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Tue, 6 Mar 2007 09:42:01 +0000 (01:42 -0800)]
[PATCH] atyfb: fix kconfig error part 2
Fix implicit declarations and missing code in atyfb.
drivers/video/aty/atyfb_base.c:2137: warning: implicit declaration of function 'a
ty_ld_lcd'
drivers/video/aty/atyfb_base.c:2154: warning: implicit declaration of function 'a
ty_st_lcd'
atyfb_base.c:(.text+0x33e5c): undefined reference to `aty_ld_lcd'
atyfb_base.c:(.text+0x33eb2): undefined reference to `aty_st_lcd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Cc: James Simmons <jsimmons@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Tue, 6 Mar 2007 09:42:00 +0000 (01:42 -0800)]
[PATCH] nvidiafb backlight: Fix implicit declaration in nv_backlight
drivers/video/nvidia/nv_backlight.c: In function 'nvidia_bl_init':
drivers/video/nvidia/nv_backlight.c:103: error: implicit declaration of function 'pmac_has_backlight_type'
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Antonino Daplas <adaplas@gmail.com> Cc: James Simmons <jsimmons@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 6 Mar 2007 09:41:58 +0000 (01:41 -0800)]
[PATCH] fix build with CONFIG_NO_IDLE_HZ=n
arch/i386/kernel/vmi.c: In function 'vmi_safe_halt':
arch/i386/kernel/vmi.c:262: warning: implicit declaration of function 'vmi_stop_hz_timer'
arch/i386/kernel/vmi.c:266: warning: implicit declaration of function 'vmi_account_time_restart_hz_timer'
Thomas Gleixner [Tue, 6 Mar 2007 07:25:42 +0000 (08:25 +0100)]
[PATCH] Save/restore periodic tick information over suspend/resume
The programming of periodic tick devices needs to be saved/restored
across suspend/resume - otherwise we might end up with a system coming
up that relies on getting a PIT (or HPET) interrupt, while those devices
default to 'no interrupts' after powerup. (To confuse things it worked
to a certain degree on some systems because the lapic gets initialized
as a side-effect of SMP bootup.)
This suspend / resume thing was dropped unintentionally during the
last-minute -mm code reshuffling.
Ingo Molnar [Mon, 5 Mar 2007 13:46:30 +0000 (14:46 +0100)]
[PATCH] paravirt: re-enable COMPAT_VDSO
CONFIG_PARAVIRT broke old glibc bootup: it silently turned off the
selectability of CONFIG_COMPAT_VDSO and thus rendered distro kernels
unbootable on old-style VDSO glibc setups.
the proper solution is to keep COMPAT_VDSO available - if a hypervisor
needs any modification of that concept then we'll judge those changes in
full context, once those changes are submitted.
Ingo Molnar [Mon, 5 Mar 2007 12:20:11 +0000 (13:20 +0100)]
[PATCH] disable NMI watchdog by default
there's a new NMI watchdog related problem: KVM crashes on certain
bzImages because ... we enable the NMI watchdog by default (even if the
user does not ask for it) , and no other OS on this planet does that so
KVM doesnt have emulation for that yet. So KVM injects a #GP, which
crashes the Linux guest:
general protection fault: 0000 [#1]
PREEMPT SMP
Modules linked in:
CPU: 0
EIP: 0060:[<c011a8ae>] Not tainted VLI
EFLAGS: 00000246 (2.6.20-rc5-rt0 #3)
EIP is at setup_apic_nmi_watchdog+0x26d/0x3d3
and no, i did /not/ request an nmi_watchdog on the boot command line!
Solution: turn off that darn thing! It's a debug tool, not a 'make life
harder' tool!!
with this patch the KVM guest boots up just fine.
And with this my laptop (Lenovo T60) also stopped its sporadic hard
hanging (sometimes in acpi_init(), sometimes later during bootup,
sometimes much later during actual use) as well. It hung with both
nmi_watchdog=1 and nmi_watchdog=2, so it's generally the fact of NMI
injection that is causing problems, not the NMI watchdog variant, nor
any particular bootup code.
[ NMI breaks on some systems, esp in combination with SMM -Arjan ]
Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Mon, 5 Mar 2007 12:15:40 +0000 (13:15 +0100)]
[PATCH] paravirt: let users decide whether they want VMI
do not use default=y for CONFIG_VMI (we do not do that for any driver or
special-hardware feature): the overwhelming majority of Linux users does
not need it, and interested users and distributions can enable it
as-needed.
Ingo Molnar [Mon, 5 Mar 2007 12:13:46 +0000 (13:13 +0100)]
[PATCH] paravirt: clarify VMI description
Clarify the description of the CONFIG_VMI option: describe the reality
that VMI is a VMWare-only interface for now. Once that changes and
another hypervisor adopts the VMI ABI we can change the text.
As can be seen from the Xen paravirtualization patches submitted to lkml
the Xen project has chosen its own, non-VMI interface between Xen and
the para-Linux - so remove Xen from the description.
CT based mach64 cards were reported to hang on sparc64 boxes when
compiled with gcc-4.1.x and later.
Looking at this piece of code, it's no surprise. A critical
delay was implemented as an empty for() loop, and gcc 4.0.x
and previous did not optimize it away, so we did get a delay.
But gcc-4.1.x and later can optimize it away, and we get crashes.
Use a real udelay() to fix this. Fix verified on SunBlade100.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Mon, 5 Mar 2007 08:30:56 +0000 (00:30 -0800)]
[PATCH] arch/i386/kernel/vmi.c must #include <asm/kmap_types.h>
CC arch/i386/kernel/vmi.o
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c: In function 'vmi_map_pt_hook':
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE0' undeclared (first use in this function)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: (Each undeclared identifier is reported only once
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: for each function it appears in.)
/home/bunk/linux/kernel-2.6/linux-2.6.21-rc2-mm1/arch/i386/kernel/vmi.c:387: error: 'KM_PTE1' undeclared (first use in this function)
make[2]: *** [arch/i386/kernel/vmi.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Zachary Amsden <zach@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Which means the spinlocks are taken in an order which depends on which cpu
gets shut down from which other cpu. Therefore lockdep complains that there
might be an ABBA deadlock. Since migrate_hrtimers() gets only called on
cpu hotplug it's safe to assume that it isn't executed concurrently on a
The same problem exists in kernel/timer.c: migrate_timers().
As pointed out by Christian Borntraeger one possible solution to avoid
the locking order complaints would be to make sure that the locks are
always taken in the same order. E.g. by taking the lock of the cpu with
the lower number first.
To achieve this we introduce two new spinlock functions double_spin_lock
and double_spin_unlock which lock or unlock two locks in a given order.
Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: John Stultz <johnstul@us.ibm.com> Cc: Christian Borntraeger <cborntra@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] ipmi: check, if default ports are accessible on PPC
ipmi_si_intf tries to access default ports, if no device could be found
elsewhere. On PPC we have a function to check, if these legacy IO ports
are accessible. This patch adds a check for these ports on PPC. This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Acked-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Corey Minyard <minyard@acm.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- In fact we don't have to fail if AOP_TRUNCATED_PAGE was returned from
prepare_write or commit_write. It is beter to retry attempt where it
is possible.
- Rearange ecryptfs_get_lower_page() error handling logic, make it more clean.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org> Acked-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] ecryptfs: lower root result must be adirectory
- Currently after path_lookup succeed we dot't have any guarantie what
it is DIR. This must be explicitly demanded.
- path_lookup can't return negative dentry, So inode check is useless.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org> Acked-by: Michael Halcrow <mhalcrow@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Mon, 5 Mar 2007 08:30:44 +0000 (00:30 -0800)]
[PATCH] md: fix for raid6 reshape
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zachary Amsden [Mon, 5 Mar 2007 08:30:43 +0000 (00:30 -0800)]
[PATCH] vmi: smp fixes
Critical fixes for SMP.
Fix a couple functions which needed to be __devinit and fix a bogus parameter
to AP startup that just so happened to work because the low virtual mapping of
memory was still established.
Zachary Amsden [Mon, 5 Mar 2007 08:30:41 +0000 (00:30 -0800)]
[PATCH] vmi: apic ops
Use para_fill instead of directly setting the APIC ops to the result of the
vmi_get_function call - this allows one to implement a VMI ROM without
implementing APIC functions, just using the native APIC functions.
While doing this, I realized that there is a lot more cleanup that should have
been done. Basically, we should never assume that the ROM implements a
specific set of functions, and always allow fallback to the native
implementation.
This is critical for future compatibility.
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws> Signed-off-by: Zachary Amsden <zach@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zachary Amsden [Mon, 5 Mar 2007 08:30:41 +0000 (00:30 -0800)]
[PATCH] vmi: fix nohz compile
More goo from hrtimers integration. We do compile and run properly with NO_HZ
enabled. There was a period when we didn't because of a missing export, but
that was since fixed.
And with the clocksource code now firmly in place, we can get rid of code that
fixes up the wallclock, since this is done in the common infrastructure. This
actually fixes a timer bug as well, that was caused by do_settimeofday no
longer being callable with interrupts disabled due to the use of
on_each_cpu().
Zachary Amsden [Mon, 5 Mar 2007 08:30:39 +0000 (00:30 -0800)]
[PATCH] vmi: pit override
The time_init_hook in paravirt-ops no longer functions in the correct manner
after the integration of the hrtimers code. The problem is that now the call
path for time initialization is:
If this isn't confusing enough, the paravirt case goes through an indirect
function pointer in the paravirt-ops table. The problem is, by the time the
paravirt hook is called, the pit timer is already enabled.
But paravirt guests have their own timer, and don't want to use the PIT.
Rather than intensify the struggle for power going on here, just make it all
nice and simple and just unconditionally do all timer setup in the
late_time_init hook. This also has the advantage of enabling timers in the
same place in all code paths, so everyone has the same bugs and we don't have
outliers who break other code because they turn on timer too early or too
late.
So the paravirt-ops time init function is now by default hpet_time_init, which
is the time init function used for native hardware. Paravirt guests have the
chance to override this when they setup the paravirt-ops table, and should
need no change.
Zachary Amsden [Mon, 5 Mar 2007 08:30:38 +0000 (00:30 -0800)]
[PATCH] vmi: paravirt drop udelay op
Not respecting udelay causes problems with any virtual hardware that is passed
through to real hardware. This can be noticed by any device that interacts
with the real world in real time - like AP startup, which takes real time. Or
keyboard LEDs, which should blink in real-time. Or floppy drives, but only
when passed through to a real floppy controller on OSes which can't
sufficiently buffer the floppy commands to emulate a zero latency floppy. Or
IDE drives, when connecting to a physical CDROM.
This was mostly a hack to get the kernel to boot faster, but it introduced a
number of misvirtualization bugs, and Alan and Pavel argued pretty strongly
against it. We were the only client, and now want to clean up this cruft.
Zachary Amsden [Mon, 5 Mar 2007 08:30:37 +0000 (00:30 -0800)]
[PATCH] vmi: fix highpte
Provide a PT map hook for HIGHPTE kernels to designate where they are mapping
page tables. This information is required so the physical address of PTE
updates can be determined; otherwise, the mm layer would have to carry the
physical address all the way to each PTE modification callsite, which is even
more hideous that the macros required to provide the proper hooks.
So lets not mess up arch neutral code to achieve this, but keep the horror in
an #ifdef HIGHPTE in include/asm-i386/pgtable.h. I had to use macros here
because some types are not yet defined in all the include paths for this
header.
This patch is absolutely required for HIGHPTE kernels to operate properly with
VMI.
Zachary Amsden [Mon, 5 Mar 2007 08:30:36 +0000 (00:30 -0800)]
[PATCH] vmi: cpu cycles fix
In order to share the common code in tsc.c which does CPU Khz calibration, we
need to make an accurate value of CPU speed available to the tsc.c code. This
value loses a lot of precision in a VM because of the timing differences with
real hardware, but we need it to be as precise as possible so the guest can
make accurate time calculations with the cycle counters.
Zachary Amsden [Mon, 5 Mar 2007 08:30:35 +0000 (00:30 -0800)]
[PATCH] vmi: sched clock paravirt op fix
The custom_sched_clock hook is broken. The result from sched_clock needs to
be in nanoseconds, not in CPU cycles. The TSC is insufficient for this
purpose, because TSC is poorly defined in a virtual environment, and mostly
represents real world time instead of scheduled process time (which can be
interrupted without notice when a virtual machine is descheduled).
To make the scheduler consistent, we must expose a different nature of time,
that is scheduled time. So deprecate this custom_sched_clock hack and turn it
into a paravirt-op, as it should have been all along. This allows the tsc.c
code which converts cycles to nanoseconds to be shared by all paravirt-ops
backends.
It is unfortunate to add a new paravirt-op, but this is a very distinct
abstraction which is clearly different for all virtual machine
implementations, and it gets rid of an ugly indirect function which I
ashamedly admit I hacked in to try to get this to work earlier, and then even
got in the wrong units.
Zachary Amsden [Mon, 5 Mar 2007 08:30:34 +0000 (00:30 -0800)]
[PATCH] vmi: timer fixes round two
Critical bugfixes for the VMI-Timer code.
1) Do not setup a one shot alarm if we are keeping the periodic alarm
armed. Additionally, since the periodic alarm can be run at a lower rate
than HZ, let's fixup the guard to the no-idle-hz mode appropriately. This
fixes the bug where the no-idle-hz mode might have a higher interrupt rate
than the non-idle case.
2) The interrupt handler can no longer adjust xtime due to nested lock
acquisition. Drop this. We don't need to check for wallclock time at
every tick, it can be done in userspace instead.
3) Add a bypass to disable noidle operation. This is useful as a last
minute workaround, or testing measure.
4) The code to skip the IO_APIC timer testing (no_timer_check) should be
conditional on IO_APIC, not SMP, since UP kernels can have this configured
in as well.
Signed-off-by: Dan Hecht <dhecht@vmware.com> Signed-off-by: Zachary Amsden <zach@vmware.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we do not check for vma flags if sys_move_pages is called to move
individual pages. If sys_migrate_pages is called to move pages then we
check for vm_flags that indicate a non migratable vma but that still
includes VM_LOCKED and we can migrate mlocked pages.
Extract the vma_migratable check from mm/mempolicy.c, fix it and put it
into migrate.h so that is can be used from both locations.
Problem was spotted by Lee Schermerhorn
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Mon, 5 Mar 2007 08:30:31 +0000 (00:30 -0800)]
[PATCH] fb: sm501fb off-by-1 sysfs store
Currently sm501fb_crtsrc_store() won't allow the routing to be changed via
echos from userspace in to the sysfs file. The reason for this is that the
strnicmp() for both heads uses a sizeof() for the string length, which ends
up being strlen() + 1 (\0 in the normal case, but the echo gives a newline,
which is where the issue occurs), this then causes a mismatch and
subsequently bails with the -EINVAL.
In addition to this, the hardcoded lengths were then used for the store
length that was returned, which ended up being erroneous and resulting in a
write error. There's also no point in returning anything but the full
length since it will -EINVAL out on a mismatch well before then anyways.
sizeof("string") is great for making sure you have space in your buffer,
but rather less so for string comparisons :-)
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Ben Dooks <ben-linux@fluff.org> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Con Kolivas [Mon, 5 Mar 2007 08:30:29 +0000 (00:30 -0800)]
[PATCH] sched: remove SMT nice
Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared. The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.
Remove the associated per_cpu_gain variable in sched_domains used only by
this code.
Also:
The reason is that with dynticks enabled, this code breaks without yet
further tweaks so dynticks brought on the rapid demise of this code. So
either we tweak this code or kill it off entirely. It was Ingo's preference
to kill it off. Either way this needs to happen for 2.6.21 since dynticks
has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Mon, 5 Mar 2007 08:30:27 +0000 (00:30 -0800)]
[PATCH] schedule wext/rtnl for removal
Since wext is being replaced as fast as we can (it'll probably stick around
for legacy drivers though) and the wext/netlink stuff was never really
used, this schedules it for removal.
The removal schedule is tight but there are no users of the code, the main
user of the wext user interface are the wireless-tools, they only have an
alpha version using the netlink interface and even that is incomplete.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 5 Mar 2007 08:30:18 +0000 (00:30 -0800)]
[PATCH] add CONFIG_GENERIC_GPIO
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Richard Purdie <rpurdie@rpsys.net> Cc: Arnaud Patard <arnaud.patard@rtp-net.org> Cc: <raph@8d.com> Cc: <msvoboda@ra.rockwell.com> Cc: pHilipp Zabel <philipp.zabel@gmail.com> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Breeds [Mon, 5 Mar 2007 08:30:14 +0000 (00:30 -0800)]
[PATCH] Fix soft lockup with iSeries viocd driver
Fix soft lockup with iSeries viocd driver, caused by eventually calling
end_that_request_first() with nr_bytes 0.
Some versions of hald do an SG_IO ioctl on the viocd device which becomes a
request with hard_nr_sectors and hard_cur_sectors set to zero. Passing zero
as the number of sectors to end_request() (which calls
end_that_request_first()) causes an infinite loop when the bio is being freed.
This patch makes sure that the zero is never passed. It only requires some
number larger the the request size the terminate the loop.
The lockup is triggered by hald, interrogating the device.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 5 Mar 2007 08:30:13 +0000 (00:30 -0800)]
[PATCH] parport is an orphan
The writing on the wall seem to be that the parport stack is orphaned,
rather than maintained by four folk ... and having a webpage that says the
latest patches are based on a 2.5 kernel.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] msi: support masking msi irqs without a mask bit
For devices that do not support msi-x we only support 1 interrupt. Therefore
we can disable that one interrupt by disabling the msi capability itself. If
we leave the intx interrupts disabled while we have the msi capability
disabled no interrupts should be delivered from that device.
Devices with just the minimal msi support (and thus hitting this code path)
include things like the intel e1000 nic, so it looks like is going to be a
fairly common case and thus important to get right.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
enable/disable_msi_mode have several side effects which keeps them from being
generally useful. So this patch replaces them with with two much more
targeted functions: msi_set_enable and msix_set_enable.
This patch makes pci_dev->msi_enabled and pci_dev->msix_enabled the definitive
way to test if linux has enabled the msi capability, and has the appropriate
msi data structures set up.
This patch ensures that while writing the msi messages in save/restore and
during device initialization we have the msi capability disabled so we don't
get into races. The pci spec requires that we do not have the msi capability
enabled and the msi messages unmasked while we write the messages. Completely
disabling the capability is overkill but it is easy :)
Care has been taken so we never have both a msi capability and intx enabled
simultaneously. We haven't run into a problem yet but better safe then sorry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] msi: sanely support hardware level msi disabling
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Ellerman <michael@ellerman.id.au> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Mon, 5 Mar 2007 08:30:04 +0000 (00:30 -0800)]
[PATCH] cyclades: return closing_wait
In http://bugzilla.kernel.org/show_bug.cgi?id=8065, Shen points out that the
cyclades driver forget to return closing_wait to userspace.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Shen <shanlu@cs.uiuc.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Purdie [Sat, 3 Mar 2007 17:43:52 +0000 (17:43 +0000)]
backlight: Allow enable/disable of fb backlights, fixing regressions
Enabling the backlight by default appears to cause problems for many
users. This patch disables backlight controls unless explicitly
enabled by users via a module parameter. Since PMAC users are known
to work, default to enabled in that case.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: Avoid a 4-order allocation.
[HDLC] Fix dev->header_cache_update having a random value.
[NetLabel]: Verify sensitivity level has a valid CIPSO mapping
[PPPOE]: Key connections properly on local device.
[AF_UNIX]: Test against sk_max_ack_backlog properly.
[NET]: Fix bugs in "Whether sock accept queue is full" checking
Linus Torvalds [Sun, 4 Mar 2007 21:15:48 +0000 (13:15 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Linus Torvalds [Sun, 4 Mar 2007 21:15:00 +0000 (13:15 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] MTX1: clear PCI errors
[MIPS] MTX1: add idsel cardbus ressources
[MIPS] MTX1: remove unneeded settings
[MIPS] dma_sync_sg_for_cpu is a no-op except for non-coherent R10000s.
[MIPS] Cobalt: update reserved resources
[MIPS] SN: PCI fixup needs to include <irq.h>.
[MIPS] DMA: Fix a bunch of warnings due to missing inline keywords.
[MIPS] RM: It should be #ifdef CONFIG_FOO not #if CONFIG_FOO ...
[MIPS] Fix and cleanup the mess that a dozen prom_printf variants are.
[MIPS] DEC: Remove redeclarations of mips_machgroup and mips_machtype.
[MIPS] No need to write c0_compare in plat_timer_setup
[MIPS] Convert to RTC-class ds1742 driver
[MIPS] Oprofile: Add missing break statements.
[MIPS] jmr3927: build fix
[MIPS] SNI: Fix mc146818_decode_year
[MIPS] Replace sys32_timer_create with the generic compat_sys_timer_create.
[MIPS] Replace sys32_socketcall with the generic compat_sys_socketcall.
[MIPS] N32 waitid is the same as o32.
Russell King [Sun, 4 Mar 2007 20:40:50 +0000 (20:40 +0000)]
[ARM] Acorn: move the i2c bus driver into drivers/i2c
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:21:38 +0000 (20:21 +0000)]
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:33:07 +0000 (20:33 +0000)]
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
Replace the I2C bus address, as per drivers/acorn/char/pcf8583.c.
Also, since this driver also contains Acorn RiscPC specific code
for obtaining the current year from the SRAM (and updating the
platform specific checksum when writing new data back) this is
NOT a platform independent driver.
Document it as such, and update the dependencies to reflect this
fact.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 4 Mar 2007 20:12:07 +0000 (20:12 +0000)]
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
Both BCD_TO_BIN(x) and BIN_TO_BCD(x) have an unexpected side-effect -
not only do they return the value as expected, they _modify_ their
argument in the process.
Let's play it safe and avoid these macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avi Kivity [Mon, 26 Feb 2007 14:29:43 +0000 (16:29 +0200)]
KVM: Fix bogus failure in kvm.ko module initialization
A bogus 'return r' can cause an otherwise successful module load to fail.
This both denies users the use of kvm, and it also denies them the use of
their machine, as it leaves a filesystem registered with its callbacks
pointing into now-freed module memory.
Fix by returning a zero like a good module.
Thanks to Richard Lucassen <mailinglists@lucassen.org> (?) for reporting
the problem and for providing access to a machine which exhibited it.
Uri Lublin [Thu, 22 Feb 2007 15:37:32 +0000 (17:37 +0200)]
KVM: Remove write access permissions when dirty-page-logging is enabled
Enabling dirty page logging is done using KVM_SET_MEMORY_REGION ioctl.
If the memory region already exists, we need to remove write accesses,
so writes will be caught, and dirty pages will be logged.
Signed-off-by: Uri Lublin <uril@qumranet.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
projects / linux-2.6-omap-h63xx.git / log