Ben Dooks [Fri, 20 Feb 2009 17:33:08 +0000 (20:33 +0300)]
sdhci: Add quirk for controllers with no end-of-busy IRQ
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: musb: fix srp sysfs entry deletion
USB: musb: resume suspended root hub on disconnect
USB: musb: use right poll limit for low speed devices
USB: musb: be careful with 64K+ transfer lengths, host side
USB: musb: fix data toggle saving with shared FIFO
USB: musb: host endpoint_disable() oops fixes
USB: musb: fix urb_dequeue() method
USB: musb: fix musb_host_tx() for shared endpoint FIFO
USB: musb: be careful with 64K+ transfer lengths (gadget side)
usb: musb: make Davinci *work* in mainline
USB: usb_get_string should check the descriptor type
USB: gadget: fix build error in omap_apollon_2420_defconfig
USB: g_file_storage: automatically disable stalls under Atmel
USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
USB: Quirk for Hummingbird huc56s / Conexant ACM modem
USB: serial: add support for second revision of Ericsson F3507G WWAN card
USB: cdc-acm: add usb id for motomagx phones
USB: option: add BenQ 3g modem information
usb: gadget: obex: select correct ep descriptors
USB: EHCI: slow down ITD reuse
...
Linus Torvalds [Sat, 28 Feb 2009 00:48:33 +0000 (16:48 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
Revert "MIPS: Print irq handler description"
MIPS: CVE-2009-0029: Enable syscall wrappers.
MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0
MIPS: Only allow Cavium OCTEON to be configured for boards that support it
Linus Torvalds [Sat, 28 Feb 2009 00:43:05 +0000 (16:43 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
Linus Torvalds [Sat, 28 Feb 2009 00:40:00 +0000 (16:40 -0800)]
Merge branch 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: ap325rxa: Revert ov772x support.
serial: sh-sci: fix overrun error handling for SH7785 SCIF.
sh: Storage class should be before const qualifier
Commit 8e961870bb9804110d5c8211d5d9d500451c4518 removed the FREEZE/THAW
handling in xfs_compat_ioctl but never added any compat handler back, so
now any freeze/thaw request from a 32-bit binary ond 64-bit userspace
will fail.
As these ioctls are 32/64-bit compatible two simple COMPATIBLE_IOCTL
entries in fs/compat_ioctl.c will do the job.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andy Whitcroft [Fri, 27 Feb 2009 22:03:05 +0000 (14:03 -0800)]
checkpatch: make in_atomic ok in the core
We say that in_atomic() is ok in the core kernel, but then always report
it regardless of where in the kernel it is. Keep quiet if it is used in
kernel/*.
Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 27 Feb 2009 22:03:03 +0000 (14:03 -0800)]
Fix recursive lock in free_uid()/free_user_ns()
free_uid() and free_user_ns() are corecursive when CONFIG_USER_SCHED=n,
but free_user_ns() is called from free_uid() by way of uid_hash_remove(),
which requires uidhash_lock to be held. free_user_ns() then calls
free_uid() to complete the destruction.
Fix this by deferring the destruction of the user_namespace.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Serge Hallyn <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Benny Halevy [Fri, 27 Feb 2009 22:02:59 +0000 (14:02 -0800)]
EXPORT_SYMBOL(d_obtain_alias) rather than EXPORT_SYMBOL_GPL
Commit 4ea3ada2955e4519befa98ff55dd62d6dfbd1705 declares d_obtain_alias()
as EXPORT_SYMBOL_GPL where it's supposed to replace d_alloc_anon which was
previously declared as EXPORT_SYMBOL and thus available to any loadable
module.
This patch reverts that.
Signed-off-by: Benny Halevy <bhalevy@panasas.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Christoph Hellwig <hch@infradead.org> Cc: "J. Bruce Fields" <bfields@fieldses.org> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Gardner [Fri, 27 Feb 2009 22:02:58 +0000 (14:02 -0800)]
w1_ds2433: clear the validcrc flag after a write
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read. The validcrc flag should be cleared after a write so
that the new value can be read.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com> Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anand Gadiyar [Sat, 21 Feb 2009 23:31:40 +0000 (15:31 -0800)]
USB: musb: resume suspended root hub on disconnect
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.
Easily seen when a hub is connected with no device attached to it;
it will autosuspend. When the hub is disconnected, it still shows
up in /proc/bus/usb/devices
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Sat, 21 Feb 2009 23:31:23 +0000 (15:31 -0800)]
USB: musb: be careful with 64K+ transfer lengths, host side
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.
Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Sat, 21 Feb 2009 23:31:13 +0000 (15:31 -0800)]
USB: musb: fix data toggle saving with shared FIFO
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO. This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sergei Shtylyov [Sat, 21 Feb 2009 23:31:01 +0000 (15:31 -0800)]
USB: musb: host endpoint_disable() oops fixes
The musb_h_disable() routine can oops in some cases:
- It's not safe to read hep->hcpriv outside musb->lock,
since it gets changed on completion IRQ paths.
- The list iterators aren't safe to use in that way;
just remove the first element while !list_empty(),
so deletions on other code paths can't make trouble.
We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.
Sergei Shtylyov [Sat, 21 Feb 2009 23:30:45 +0000 (15:30 -0800)]
USB: musb: fix urb_dequeue() method
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint. That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.
Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback). Since a QH with an empty URB
list is now supposed to be freed, do that. And remove a now-useless
check from musb_advance_schedule().
[ dbrownell@users.sourceforge.net: update patch description,
and fold in a dequeue() comment patch ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: musb: fix musb_host_tx() for shared endpoint FIFO
The input queue should be used for TX on endpoints which
share FIFO hardware. The host TX path wasn't doing that.
Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.
Felipe Balbi [Sat, 21 Feb 2009 23:29:42 +0000 (15:29 -0800)]
USB: musb: be careful with 64K+ transfer lengths (gadget side)
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.
David Brownell [Fri, 20 Feb 2009 21:45:17 +0000 (13:45 -0800)]
usb: musb: make Davinci *work* in mainline
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:
- Use clk_enable()/clk_disable() ... the "always enable USB clocks"
code this originally relied on has since been removed.
- Initialize the USB device only after the relevant I2C GPIOs are
available, so the host side can properly enable VBUS.
- Tweak init sequencing to cope with mainline's relatively late init
of the I2C system bus for power switches, transceivers, and so on.
Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested. Also
verified on OMAP3.
(Unrelated: correct the MODULE_PARM_DESC spelling of musb_debug.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 20 Feb 2009 21:33:08 +0000 (16:33 -0500)]
USB: usb_get_string should check the descriptor type
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter. This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor! The
usb_get_string() routine needs to check whether it got the right
type of descriptor.
Oddly enough, this sort of check is already present in
usb_get_descriptor(). The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.
Alan Stern [Tue, 24 Feb 2009 21:19:47 +0000 (16:19 -0500)]
USB: g_file_storage: automatically disable stalls under Atmel
This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 23 Feb 2009 17:02:05 +0000 (12:02 -0500)]
USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter. Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.
Tested-by: Mike Lampard <mike@mtgambier.net> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.
Karsten Wiese [Mon, 9 Feb 2009 00:07:58 +0000 (16:07 -0800)]
USB: EHCI: slow down ITD reuse
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state. This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.
This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.
This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.
Li Yang [Fri, 13 Feb 2009 08:14:39 +0000 (16:14 +0800)]
USB: fsl_usb2_udc: fix potential queue head corruption
Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.
Signed-off-by: Li Yang <leoli@freescale.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pekka Enberg [Fri, 30 Jan 2009 09:32:47 +0000 (11:32 +0200)]
Staging: w35und: fix usb_control_msg() error handling in wb35_probe()
If successful, the usb_control_msg() function returns the number of
bytes transferred. Fix up wb35_probe() to only bail out if the function returns
a negative number. Also, fix up ieee80211_alloc_hw() error code to ENOMEM;
otherwise GCC complains that err might be undefined (and is right about that).
Acked-by: Pavel Machek <pavel@suse.cz> Reported-and-tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check for null pardevice (not registered, ej: panel never attached,
inexistent parport, etc. ) before calling parport_release,
parport_unregister_device, and related funcs on module release.
Staging: rtl8187se: Fix oops and memory poison caused by builtin ieee80211.
when modprobe and removing rtl8187se ( just for testing, i do not have
that card , and oops and a memory poison error happens on the builtin
ieee80211 of that driver. I dont know if they will port it to the
current ieeee80221 instead of the builtin ones, but just in case i
attach a proposed fix for that problem.
- Change for loop on ieee80211_crypto_deinit for list_for_each_safe to
remove items. Is there an spinlock needed here?
- Call ieee80211_crypto_deinit after exiting all registerd crypto protocols.
Randy Dunlap [Wed, 11 Feb 2009 21:20:44 +0000 (13:20 -0800)]
Staging: rtl8187se: fix Kconfig dependencies
rtl8187se uses wireless extensions so it needs to depend on
WIRELESS_EXT (or select it).
rtl8187se uses fields in struct net_device that are only present
if CONFIG_COMPAT_NET_DEV_OPS=y, so it needs to depend on
that symbol also.
drivers/staging/rtl8187se/r8180_core.c:5973: error: 'struct net_device' has no member named 'wireless_handlers'
drivers/staging/rtl8187se/r8180_core.c:5982: error: 'struct net_device' has no member named 'wireless_handlers'
drivers/staging/rtl8187se/r8180_core.c:201: error: 'struct net_device' has no member named 'stop'
drivers/staging/rtl8187se/r8180_core.c:4584: error: 'struct net_device' has no member named 'get_stats'
drivers/staging/rtl8187se/r8180_core.c:5969: error: 'struct net_device' has no member named 'open'
drivers/staging/rtl8187se/r8180_core.c:5970: error: 'struct net_device' has no member named 'stop'
drivers/staging/rtl8187se/r8180_core.c:5972: error: 'struct net_device' has no member named 'tx_timeout'
drivers/staging/rtl8187se/r8180_core.c:5974: error: 'struct net_device' has no member named 'do_ioctl'
drivers/staging/rtl8187se/r8180_core.c:5975: error: 'struct net_device' has no member named 'set_multicast_list'
drivers/staging/rtl8187se/r8180_core.c:5976: error: 'struct net_device' has no member named 'set_mac_address'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.
There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.
This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.
This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.
Nicola Soranzo [Thu, 19 Feb 2009 16:41:56 +0000 (13:41 -0300)]
V4L/DVB (10659): em28xx: register device to soundcard for sysfs
As explained in "Writing an ALSA driver" (T. Iwai), audio drivers should
set the struct device for the card before registering the card instance.
This will add the correct /sys/class/sound/cardN/device symlink, so HAL
can see the device and ConsoleKit sets its ACL permissions for the
logged-in user.
For em28xx audio capture cards found e.g. in Hauppauge WinTV-HVR-900 (R2),
this patch fixes errors like:
ALSA lib pcm_hw.c:1429:(_snd_pcm_hw_open) Invalid value for card
Error opening audio: Permission denied
Linus Torvalds [Thu, 26 Feb 2009 22:45:42 +0000 (14:45 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: add IO error check in ocfs2_get_sector()
ocfs2: set gap to seperate entry and value when xattr in bucket
ocfs2: lock the metaecc process for xattr bucket
ocfs2: Use the right access_* method in ctime update of xattr.
ocfs2/dlm: Make dlm_assert_master_handler() kill itself instead of the asserter
ocfs2/dlm: Use ast_lock to protect ast_list
ocfs2: Cleanup the lockname print in dlmglue.c
ocfs2/dlm: Retract fix for race between purge and migrate
ocfs2: Access and dirty the buffer_head in mark_written.
Linus Torvalds [Thu, 26 Feb 2009 22:43:42 +0000 (14:43 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: AMD 813x B2 devices do not need boot interrupt quirk
PCI: Enable PCIe AER only after checking firmware support
PCI: pciehp: Handle interrupts that happen during initialization.
PCI: don't enable too many HT MSI mappings
PCI: add some sysfs ABI docs
PCI quirk: enable MSI on 8132
powerpc/44x: Fix address decoding setup of PCI 2.x cells
The PCI 2.x cells used on some 44x SoCs only let us configure the decode
for the low 32-bit of the incoming PLB addresses. The top 4 bits (this
is a 36-bit bus) are hard wired to different values depending on the
specific SoC in use. Our code used to work "by accident" until I added
support for the ISA memory holes and while at it added more validity
checking of the addresses.
This patch should bring it back to working condition. It still relies
on the device-tree being correct but that's somewhat a pre-requisite
for anything to work anyway.
Stefan Assmann [Thu, 26 Feb 2009 18:46:48 +0000 (10:46 -0800)]
PCI: AMD 813x B2 devices do not need boot interrupt quirk
Turns out that the new AMD 813x devices do not need the
quirk_disable_amd_813x_boot_interrupt quirk to be run on them. If it
is, no interrupts are seen on the PCI-X adapter.
Kyle McMartin [Thu, 26 Feb 2009 17:57:56 +0000 (12:57 -0500)]
x86: enable DMAR by default
Now that the obvious bugs have been worked out, specifically
the iwlagn issue, and the write buffer errata, DMAR should be safe
to turn back on by default. (We've had it on since those patches were
first written a few weeks ago, without any noticeable bug reports
(most have been due to the dma-api debug patchset.))
Tiger Yang [Fri, 20 Feb 2009 03:11:50 +0000 (11:11 +0800)]
ocfs2: set gap to seperate entry and value when xattr in bucket
This patch set a gap (4 bytes) between xattr entry and
name/value when xattr in bucket. This gap use to seperate
entry and name/value when a bucket is full. It had already
been set when xattr in inode/block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Wed, 25 Feb 2009 01:40:26 +0000 (17:40 -0800)]
ocfs2: lock the metaecc process for xattr bucket
For other metadata in ocfs2, metaecc is checked in ocfs2_read_blocks
with io_mutex held. While for xattr bucket, it is calculated by
the whole buckets. So we have to add a spin_lock to prevent multiple
processes calculating metaecc.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Tested-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Mon, 16 Feb 2009 20:39:28 +0000 (04:39 +0800)]
ocfs2: Use the right access_* method in ctime update of xattr.
In ctime updating of xattr, it use the wrong type of access for
inode, so use ocfs2_journal_access_di instead.
Reported-and-Tested-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Tao Ma <tao.ma@oracle.com> Acked-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Tue, 3 Feb 2009 20:37:16 +0000 (12:37 -0800)]
ocfs2/dlm: Make dlm_assert_master_handler() kill itself instead of the asserter
In dlm_assert_master_handler(), if we get an incorrect assert master from a node
that, we reply with EINVAL asking the asserter to die. The problem is that an
assert is sent after so many hoops, it is invariably the node that thinks the
asserter is wrong, is actually wrong. So instead of killing the asserter, this
patch kills the assertee.
This patch papers over a race that is still being addressed.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Acked-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Sunil Mushran [Tue, 3 Feb 2009 20:37:13 +0000 (12:37 -0800)]
ocfs2/dlm: Retract fix for race between purge and migrate
Mainline commit d4f7e650e55af6b235871126f747da88600e8040 attempts to delay
the dlm_thread from sending the drop ref message if the lockres is being
migrated. The problem is that we make the dlm_thread wait for the migration
to complete. This causes a deadlock as dlm_thread also participates in the
lockres migration process.
A better fix for the original oss bugzilla#1012 is in testing.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com> Acked-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Thu, 8 Jan 2009 23:32:48 +0000 (07:32 +0800)]
ocfs2: Access and dirty the buffer_head in mark_written.
In __ocfs2_mark_extent_written, when we meet with the situation
of c_split_covers_rec, the old solution just replace the extent
record and forget to access and dirty the buffer_head. This will
cause a problem when the unwritten extent is in an extent block.
So access and dirty it.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Linus Torvalds [Thu, 26 Feb 2009 18:36:35 +0000 (10:36 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
xen/blkfront: use blk_rq_map_sg to generate ring entries
block: reduce stack footprint of blk_recount_segments()
cciss: shorten 30s timeout on controller reset
block: add documentation for register_blkdev()
block: fix bogus gcc warning for uninitialized var usage
Linus Torvalds [Thu, 26 Feb 2009 18:32:31 +0000 (10:32 -0800)]
Make ieee1394_init a fs-initcall
It needs to happen before any firewire driver actually registers itself,
and that was previously handled by having the Makefile list the core
ieee1394 files before the drivers.
But now there are firewire drivers in drivers/media, and the Makefile
games aren't enough. So just make ieee1394_init happen earlier in the
init sequence, the way all other bus layers already do.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Henrik Kurelid <henrik@kurelid.se> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Ben Backx <ben@bbackx.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Tue, 24 Feb 2009 07:10:09 +0000 (08:10 +0100)]
xen/blkfront: use blk_rq_map_sg to generate ring entries
On occasion, the request will apparently have more segments than we
fit into the ring. Jens says:
> The second problem is that the block layer then appears to create one
> too many segments, but from the dump it has rq->nr_phys_segments ==
> BLKIF_MAX_SEGMENTS_PER_REQUEST. I suspect the latter is due to
> xen-blkfront not handling the merging on its own. It should check that
> the new page doesn't form part of the previous page. The
> rq_for_each_segment() iterates all single bits in the request, not dma
> segments. The "easiest" way to do this is to call blk_rq_map_sg() and
> then iterate the mapped sg list. That will give you what you are
> looking for.
> Here's a test patch, compiles but otherwise untested. I spent more
> time figuring out how to enable XEN than to code it up, so YMMV!
> Probably the sg list wants to be put inside the ring and only
> initialized on allocation, then you can get rid of the sg on stack and
> sg_init_table() loop call in the function. I'll leave that, and the
> testing, to you.
[Moved sg array into info structure, and initialize once. -J]
Signed-off-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Jens Axboe [Mon, 23 Feb 2009 08:03:10 +0000 (09:03 +0100)]
block: reduce stack footprint of blk_recount_segments()
blk_recalc_rq_segments() requires a request structure passed in, which
we don't have from blk_recount_segments(). So the latter allocates one on
the stack, using > 400 bytes of stack for that. This can cause us to spill
over one page of stack from ext4 at least:
Split the segment counting out into a __blk_recalc_rq_segments() helper
to avoid allocating an onstack request just for checking the physical
segment count.
Jens Axboe [Mon, 23 Feb 2009 07:53:35 +0000 (08:53 +0100)]
cciss: shorten 30s timeout on controller reset
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This fixes a regression introduced by commit a4e22f02f5b6518c1484faea1f88d81802b9feac ("powerpc: Update 64bit
__copy_tofrom_user() using CPU_FTR_UNALIGNED_LD_STD").
The same bug that existed in the 64bit memcpy() also exists here so fix
it here too. The fix is the same as that applied to memcpy() with the
addition of fixes for the exception handling code required for
__copy_tofrom_user().
This stops us reading beyond the end of the source region we were told
to copy.
Signed-off-by: Mark Nelson <markn@au1.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This commit allowed CPUs that have the CPU_FTR_UNALIGNED_LD_STD CPU
feature bit present to do the memcpy() with unaligned load doubles. But,
along with this came a bug where our final load double would read bytes
beyond a page boundary and into the next (unmapped) page. This was caught
by enabling CONFIG_DEBUG_PAGEALLOC,
The fix was to read only the number of bytes that we need to store rather
than reading a full 8-byte doubleword and storing only a portion of that.
In order to minimise the amount of existing code touched we use the
original do_tail for the src_unaligned case.
Below is an example of the regression, as reported by Sachin Sant:
When we introduced VSX, we changed the way FPRs are stored in the
thread_struct. Unfortunately we missed the load/store float double
alignment handler code when updating how we access FPRs in the
thread_struct.
Below fixes this and merges the little/big endian case.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Wed, 25 Feb 2009 23:14:37 +0000 (15:14 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Don't go beyond iosapic_intr_info's arraysize
[IA64] Do not go beyond ARRAY_SIZE of unw.hash
[IA64] enable setting DMAR on by default
Linus Torvalds [Wed, 25 Feb 2009 23:12:48 +0000 (15:12 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_legacy: for VLB 32bit PIO don't try tricks with slop
[libata] pata_amd: program FIFO
sata_mv: fix SoC interrupt breakage
pata_it821x: resume from hibernation fails with RAID volume
Alan Cox [Wed, 11 Feb 2009 21:08:42 +0000 (13:08 -0800)]
[libata] pata_legacy: for VLB 32bit PIO don't try tricks with slop
These devices are generally used with ATA anyway and it seems that some
ATAPI will need us to issue the right number of words. Therefore as we
can't switch mid burst on VLB devices we should only use 32bit I/O for
suitable block sizes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Wed, 11 Feb 2009 21:08:41 +0000 (13:08 -0800)]
[libata] pata_amd: program FIFO
With 32bit PIO we can use the posted write buffers, but only for 32bit I/O
cycles. This means we must disable the FIFO for ATAPI where a final 16bit
cycle may occur.
Rework the FIFO logic so that we disable the FIFO then selectively
re-enable it when we set the timings on AMD devices. Also fix a case
where we scribbled on PCI config 0x41 of Nvidia chips when we shouldn't.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Thu, 19 Feb 2009 15:38:04 +0000 (10:38 -0500)]
sata_mv: fix SoC interrupt breakage
For some reason, sata_mv doesn't clear interrupt status during init
when it's running on an SoC host adapter. If the bootloader has
touched the SATA controller before starting Linux, Linux can end up
enabling the SATA interrupt with events pending, which will cause the
interrupt to be marked as spurious and then be disabled, which then
breaks all further accesses to the controller.
This patch makes the SoC path clear interrupt status on init like in
the non-SoC case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ondrej Zary [Wed, 11 Feb 2009 21:08:43 +0000 (13:08 -0800)]
pata_it821x: resume from hibernation fails with RAID volume
Hibernation didn't work for me since I started to use IT8212 controller.
I did some debugging (booting with no_console_suspend init=/bin/sh).
Found that resume fails (2.6.28) with "serial number mismatch 'some
garbage' != 'some other garbage'" and "revalidation failed" messages.
That's because the controller firmware fills different serial number in
the IDENTIFY every boot.
The patch below fixes the resume simply clearing the serial number. The
proper fix would be probably to fill in the serial number of the RAID
volume instead. I assume that there must be something like that stored on
the drives but I don't know where.
Fix resume on pata_it821x RAID volume by clearing the serial number in
IDENTIFY data, which is otherwise different on each boot.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hugh Dickins [Tue, 24 Feb 2009 20:51:52 +0000 (20:51 +0000)]
shmem: fix shared anonymous accounting
Each time I exit Firefox, /proc/meminfo's Committed_AS goes down almost
400 kB: OVERCOMMIT_NEVER would be allowing overcommits it should
prohibit.
Commit fc8744adc870a8d4366908221508bb113d8b72ee "Stop playing silly
games with the VM_ACCOUNT flag" changed shmem_file_setup() to set the
shmem file's VM_ACCOUNT flag according to VM_NORESERVE not being set in
the vma flags; but did so only _after_ the shmem_acct_size(flags, size)
call which is expected to pre-account a shared anonymous object.
It's all clearer if we switch shmem.c over to use VM_NORESERVE
throughout in place of !VM_ACCOUNT.
But I very nearly sent in a patch which mistakenly removed the
accounting from tmpfs files: shmem_get_inode()'s memset was good for not
setting VM_ACCOUNT, but now it needs to set VM_NORESERVE.
Rather than setting that by default, then perhaps clearing it again in
shmem_file_setup(), let's pass it as a flag to shmem_get_inode(): that
allows us to remove the #ifdef CONFIG_SHMEM from shmem_file_setup().
Kyle McMartin [Sat, 14 Feb 2009 09:11:29 +0000 (04:11 -0500)]
[IA64] enable setting DMAR on by default
The previous commit which introduced the DMAR_DEFAULT_ON setting in
drivers/pci/dmar.c neglected to add the ability for ia64 to enable
the IOMMU by default. Rectify that mistake, doh!
Signed-off-by: Kyle McMartin <kyle@redhat.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
projects / linux-2.6-omap-h63xx.git / log