Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: Justin Waters <justin.waters@timesys.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com> Signed-off-by: Justin Waters <justin.waters@timesys.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch brings support for gpio/gpiolib framework to Intel IOP3xx
platforms.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Feroceon platforms that have a branch prediction unit, bit 11 of the
cp15 control register controls the BPU. This patch keeps the old value
of this bit instead of always clearing it.
The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland. The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Nicolas Pitre <nico@marvell.com>
Nicolas Pitre [Fri, 27 Jun 2008 22:56:22 +0000 (18:56 -0400)]
[ARM] Orion: add RD88F5181L-FXO support
This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Ben Dooks [Mon, 7 Jul 2008 17:12:40 +0000 (18:12 +0100)]
[ARM] S3C2443: Add prediv clk and fix setting of h and p clocks
Update the S3C2443 clock support to add the prediv clock
that is sourced via a divider from msysclk. Also fix the
setting of p and h clocks from this prediv clock.
Ben Dooks [Mon, 7 Jul 2008 17:12:38 +0000 (18:12 +0100)]
[ARM] S3C2443: Fix s3c2443_clkcon_enable_p() using wrong register.
s3c2443_clkcon_enable_p() was reading from the correct register
S3C2443_PCLKCON, but then writing the value back to the wrong
register S3C2443_HCLKCON.
This patch adds support for the phyCORE-i.MX27 cpu module (aka pcm038).
It is as generic as possible in order to support any kind of baseboard.
Note: This CPU module implementation can't work without a baseboard
support. Baseboard support can be added by the PCM-970 (included in
this patch stack) or any custom variant.
Changed against the original Freescale code (and against clocklib for example):
- clock rate is always calculated whenever one ask for the current rate.
(means no "rate" member in the clock structure).
So switching the PLL base frequency will propagate immediately to all
other clocks that are depending on this frequency.
TODO:
- Check if the i.MX21 CPU can share the same code.
Daniel Mack [Sat, 5 Jul 2008 08:02:53 +0000 (10:02 +0200)]
MX3: Add basic support for LogicPD i.MX31 LiteKit
This patch adds basic support for i.MX31 LiteKit by LogicPD.
With printascii() in kernel/printk.c, it boots right into the
rootfs-panic.
Note: This is a modified version of Daniel's patch to fit into this patch
stack.
> On 09.06.2008, at 17:26, Russell King - ARM Linux wrote:
>
> > I would much prefer it if board specific includes were included by the
> > code which needs them rather than in asm/arch/hardware.h. With the
> > device model, drivers shouldn't need to include any board specific
> > includes - only the board specific C file should need it.
>
> The new version of this patch (#5102) has been uploaded to the patch
> tracker this morning.
TODO: It seems impossible to build a kernel for more than one CPU because the
timer do not follow the platform device rules. So it does only work if
timer 1 can be accessed on all CPUs at the same address.
This patch bases on the one from Daniel Mack. The most important change to
Daniel's patch is to be more generic. This gpio routine supports at least
the i.MX27 and i.MX31 processors.
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de> Acked-by: Daniel Mack <daniel@caiaq.de>
Changed against the original Freescale code (and against clocklib for example):
- clock rate is always calculated whenever one ask for the current rate
(means struct clk has no more a member called "rate"). So switching the PLL
base frequency will propagate immediately to all other clocks that are
depending on this frequency.
This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
We assumed a 16MHz reference frequency for the UART. While this
is true for i.MX1 most of the time it is not true for MX27/MX31.
Also, add handling for the ONEMS register which is present on
newer versions of the chip and pass a sane minimum baudrate to
uart_get_baud_rate().
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: adding comment for ipaq forcing number of ports
USB: fix Oops on loading ipaq module since 2.6.26
USB: add a pl2303 device id
USB: another option device id
USB: don't lose disconnections during suspend
USB: fix interrupt disabling for HCDs with shared interrupt handlers
USB: New device ID for ftdi_sio driver
sisusbvga: Fix oops on disconnect.
USB: mass storage: new id for US_SC_CYP_ATACB
USB: ohci - record data toggle after unlink
USB: ehci - fix timer regression
USB: fix cdc-acm resume()
OHCI: Fix problem if SM501 and another platform driver is selected
Stefan Becker [Tue, 1 Jul 2008 16:19:22 +0000 (19:19 +0300)]
USB: fix interrupt disabling for HCDs with shared interrupt handlers
USB: fix interrupt disabling for HCDs with shared interrupt handlers
As has been discussed several times on LKML, IRQF_SHARED | IRQF_DISABLED
doesn't work reliably, i.e. a shared interrupt handler CAN'T be certain to
be called with interrupts disabled. Most USB HCD handlers use IRQF_DISABLED
and therefore havoc can break out if they share their interrupt with a
handler that doesn't use it.
On my test machine the yenta_socket interrupt handler (no IRQF_DISABLED)
was registered before ehci_hcd and one uhci_hcd instance. Therefore all
usb_hcd_irq() invocations for ehci_hcd and for one uhci_hcd instance
happened with interrupts enabled. That led to random lockups as USB core
HCD functions that acquire the same spinlock could be called twice
from interrupt handlers.
This patch updates usb_hcd_irq() to always disable/restore interrupts.
usb_add_hcd() will silently remove any IRQF_DISABLED requested from HCD code.
Signed-off-by: Stefan Becker <stefan.becker@nokia.com> Cc: stable <stable@kernel.org> Acked-by: David Brownell <david-b@pacbell.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jon K Hellan [Tue, 24 Jun 2008 09:43:13 +0000 (11:43 +0200)]
USB: New device ID for ftdi_sio driver
Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
David Brownell [Sat, 14 Jun 2008 06:59:54 +0000 (23:59 -0700)]
USB: ohci - record data toggle after unlink
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle. This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because
(a) about half the time the data toggle bit was correct;
(b) canceling such URBs is unusual; and
(c) the few drivers which cancel these URBs either
[1] do it only as part of shutting down, or
[2] have fault recovery logic, which recovers.
For those transfer types, the toggle is normally written back
into the ED when each TD is retired. But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.
The fix is simple: the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.
(Issue found by leonidv11@gmail.com ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Leonid <leonidv11@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 14 Jun 2008 06:56:48 +0000 (23:56 -0700)]
USB: ehci - fix timer regression
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.
This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Leonid <leonidv11@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 17 Jun 2008 20:30:48 +0000 (22:30 +0200)]
USB: fix cdc-acm resume()
cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Dooks [Sun, 8 Jun 2008 16:20:11 +0000 (17:20 +0100)]
OHCI: Fix problem if SM501 and another platform driver is selected
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
J. Bruce Fields [Thu, 3 Jul 2008 19:26:35 +0000 (15:26 -0400)]
svcrpc: fix handling of garbage args
To return garbage_args, the accept_stat must be 0, and we must have a
verifier. So we shouldn't be resetting the write pointer as we reject
the call.
Also, we must add the two placeholder words here regardless of success
of the unwrap, to ensure the output buffer is left in a consistent state
for svcauth_gss_release().
This fixes a BUG() in svcauth_gss.c:svcauth_gss_release().
Thanks to Aime Le Rouzic for bug report, debugging help, and testing.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Tested-by: Aime Le Rouzic <aime.le-rouzic@bull.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unfortunately this allows the task to migrate after setting up the softirq
and raising it. Since softirqs run a queue that is per-cpu we may raise the
softirq on the wrong CPU and this will keep the queued softirq task from
running.
To solve this issue, this patch disables preemption around the releasing
of the hrtimer lock and raising of the softirq.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atsushi Nemoto [Tue, 24 Jun 2008 14:26:38 +0000 (23:26 +0900)]
[MIPS] cevt-txx9: Reset timer counter on initialization
The txx9_tmr_init() will not clear a timer counter register in a certain
case. The counter register is cleared on 1->0 transition of TCE bit if
CRE=1. So just clearing the TCE bit is not enough.
[MIPS] IP22: Fix crashes due to wrong L1_CACHE_BYTES
The introduction of a real dma cache invalidate makes it important
to have a correct cache line size, otherwise the kernel will gives
out two memory segment, which might share one cache line. The R4400
Indy/Indigo2 CPU modules are using a second level cache line size
of 128 bytes, so MIPS_L1_CACHE_SHIFT needs to be bumped up to 7 for
IP22.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's possible that the crime interrupt handler is called without
pending interrupts (probably a hardware issue). To avoid irritating
"unexpected irq 71" messages, we now just ignore the spurious crime
interrupts.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not overwrite nr_zones on !NUMA when initialising zlcache_ptr
The non-NUMA case of build_zonelist_cache() would initialize the
zlcache_ptr for both node_zonelists[] to NULL.
Which is problematic, since non-NUMA only has a single node_zonelists[]
entry, and trying to zero the non-existent second one just overwrote the
nr_zones field instead.
As kswapd uses this value to determine what reclaim work is necessary,
the result is that kswapd never reclaims. This causes processes to
stall frequently in low-memory situations as they always direct reclaim.
This patch initialises zlcache_ptr correctly.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Tested-by: Dan Williams <dan.j.williams@intel.com>
[ Simplified patch a bit ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Thu, 3 Jul 2008 11:32:51 +0000 (12:32 +0100)]
[ARM] S3C24XX: Split serial driver into core and per-cpu drivers
The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Ben Dooks [Thu, 3 Jul 2008 10:24:37 +0000 (11:24 +0100)]
[ARM] BAST/VR1000: Move to using ata_platform (libata)
Use the pata_platform driver to provide the IDE port
drivers on the Simntec BAST and Thorcom VR1000 machines
as a precursor to removing drivers/ide/arm/bast-ide.c
This will mean that the system will need SCSI and SCSI disc
support as a minimum, and any references to hdX will be
changed to sdX.
projects / linux-2.6-omap-h63xx.git / log