As reported by David Engel <david@istwok.net>, ATSC115 doesn't work
fine with mythtv. This software opens both analog and dvb interfaces of
saa7134.
What happens is that some tuner commands are going to the wrong place,
as shown at the logs:
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner 1-0061: tv freq set to 67.25
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: using tuner params #0 (ntsc)
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: freq = 67.25 (1076), range = 0, config = 0xce, cb = 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: Freq= 67.25 MHz, V_IF=45.75 MHz, Offset=0.00 MHz, div=1808
Feb 12 20:37:48 opus kernel: tuner-simple 1-000a: tv 0x07 0x10 0xce 0x01
Feb 12 20:37:48 opus kernel: tuner-simple 1-0061: tv 0x07 0x10 0xce 0x01
This happens due to a hack at TUV1236D analog setup, where it replaces
tuner address, at 0x61 for 0x0a, in order to save a few memory bytes.
The code assumes that nobody else would try to access the tuner during
that setup, but the point is that there's no lock to protect such
access. So, this opens the possibility of race conditions to happen.
Instead of hacking tuner address, this patch uses a temporary var with
the proper tuner value to be used during the setup. This should save
the issue, although we should consider to write some analog/digital
lock at saa7134 driver.
Linus Torvalds [Fri, 13 Feb 2009 16:19:11 +0000 (08:19 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Only register AC97 bus if it's not done already
ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
ALSA: hda - Add missing terminator in slave dig-out array
ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
ALSA: hda - Register (new) devices at reconfig
ALSA: mtpav - Fix initial value for input hwport
ALSA: hda - add id for Intel IbexPeak integrated HDMI codec
ALSA: hda - compute checksum in HDMI audio infoframe
ALSA: hda - enable HDMI audio pin out at module loading time
ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
ASoC: Update SDP3430 machine driver for snd_soc_card
ALSA: hda - Add quirk for Asus z37e (1043:8284)
sound: Remove OSSlib stuff from linux/soundcard.h
ASoC: WM8990: Fix kcontrol's private value use in put callback
ASoC: TLV320AIC3X: Fix kcontrol's private value use in put callback
Serge E. Hallyn [Fri, 13 Feb 2009 14:04:21 +0000 (14:04 +0000)]
User namespaces: Only put the userns when we unhash the uid
uids in namespaces other than init don't get a sysfs entry.
For those in the init namespace, while we're waiting to remove
the sysfs entry for the uid the uid is still hashed, and
alloc_uid() may re-grab that uid without getting a new
reference to the user_ns, which we've already put in free_user
before scheduling remove_user_sysfs_dir().
Mark Brown [Thu, 12 Feb 2009 19:33:19 +0000 (19:33 +0000)]
ASoC: Only register AC97 bus if it's not done already
ASoC supports both explicit codec drivers for AC97 devices and a simple
driver which uses the standard ALSA AC97 framework for codec support.
When used with the generic AC97 codec support that will provide the
ad hoc AC97 device for drivers like touchscreens to attach to so the
core shouldn't do so.
Reported-by: Manuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai [Fri, 13 Feb 2009 10:32:28 +0000 (11:32 +0100)]
ALSA: hda - Add snd_hda_multi_out_dig_cleanup()
Added the helper function snd_hda_multi_out_dig_cleanup() to clean up
the digital outputs with multi setup. This call is needed in cases
the codec supports multiple digital outputs as slaves. Otherwise the
slave widgets aren't properly cleaned up.
For a single digital output (e.g. in patch_conexant.c), this call isn't
needed.
ALSA: hda - Change HP dv7 (103c:30f4) quirk from hp-m4 to hp-dv5 model
Change HP dv7 quirk: although reported to work with hp-m4 model
(https://bugzilla.novell.com/show_bug.cgi?id=445321), the original
report doesn't contain info about testing of internal microphone.
Recently I received a report about internal mic not working
(https://qa.mandriva.com/show_bug.cgi?id=44855#c193), this must be
related with the forced line in on pin 0x0e done with hp-m4 model. Thus
change the current quirk from STAC_HP_M4 to STAC_HP_DV5, later reported
to be fixed on a provided kernel with this change
(https://qa.mandriva.com/show_bug.cgi?id=44855#c196).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
net: 4 bytes kernel memory disclosure in SO_BSDCOMPAT gsopt try #2
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
bnx2: Update version to 1.9.2 and copyright.
bnx2: Fix jumbo frames error handling.
bnx2: Update 5709 firmware.
bnx2: Update 5706/5708 firmware.
3c505: do not set pcb->data.raw beyond its size
Documentation/connector/cn_test.c: don't use gfp_any()
net: don't use in_atomic() in gfp_any()
IRDA: cnt is off by 1
netxen: remove pcie workaround
sun3: print when lance_open() fails
qlge: bugfix: Add missing rx buf clean index on early exit.
qlge: bugfix: Fix RX scaling values.
qlge: bugfix: Fix TSO breakage.
qlge: bugfix: Add missing dev_kfree_skb_any() call.
qlge: bugfix: Add missing put_page() call.
qlge: bugfix: Fix fatal error recovery hang.
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
...
wimax: fix oops in wimax_dev_get_by_genl_info() when looking up non-wimax iface
When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.
Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.
Yang Hongyang [Fri, 13 Feb 2009 00:57:12 +0000 (16:57 -0800)]
netxen: fix compile waring "label ‘set_32_bit_mask’ defined but not used" on IA64 platform
When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’
defined but not used
We do not need label ‘set_32_bit_mask’ on IA64 platform,So move it to #else.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 13 Feb 2009 00:54:13 +0000 (16:54 -0800)]
bnx2: Fix jumbo frames error handling.
If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them. Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 13 Feb 2009 00:53:48 +0000 (16:53 -0800)]
bnx2: Update 5709 firmware.
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 13 Feb 2009 00:53:22 +0000 (16:53 -0800)]
bnx2: Update 5706/5708 firmware.
New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers. In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Fri, 13 Feb 2009 00:52:31 +0000 (16:52 -0800)]
3c505: do not set pcb->data.raw beyond its size
Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Fri, 13 Feb 2009 00:43:17 +0000 (16:43 -0800)]
net: don't use in_atomic() in gfp_any()
The problem is that in_atomic() will return false inside spinlocks if
CONFIG_PREEMPT=n. This will lead to deadlockable GFP_KERNEL allocations
from spinlocked regions.
Secondly, if CONFIG_PREEMPT=y, this bug solves itself because networking
will instead use GFP_ATOMIC from this callsite. Hence we won't get the
might_sleep() debugging warnings which would have informed us of the buggy
callsites.
Solve both these problems by switching to in_interrupt(). Now, if someone
runs a gfp_any() allocation from inside spinlock we will get the warning
if CONFIG_PREEMPT=y.
I reviewed all callsites and most of them were too complex for my little
brain and none of them documented their interface requirements. I have no
idea what this patch will do.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:38:34 +0000 (16:38 -0800)]
qlge: bugfix: Add missing rx buf clean index on early exit.
The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs. This can happen when a
page alloc or dma mapping fails. If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:38:18 +0000 (16:38 -0800)]
qlge: bugfix: Fix RX scaling values.
Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Fri, 13 Feb 2009 00:36:50 +0000 (16:36 -0800)]
qlge: bugfix: Use netif_receive_skb() and vlan_hwaccel_receive_skb().
Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nick Piggin [Thu, 12 Feb 2009 03:34:23 +0000 (04:34 +0100)]
Fix page writeback thinko, causing Berkeley DB slowdown
A bug was introduced into write_cache_pages cyclic writeout by commit 31a12666d8f0c22235297e1c1575f82061480029 ("mm: write_cache_pages cyclic
fix"). The intention (and comments) is that we should cycle back and
look for more dirty pages at the beginning of the file if there is no
more work to be done.
But the !done condition was dropped from the test. This means that any
time the page writeout loop breaks (eg. due to nr_to_write == 0), we
will set index to 0, then goto again. This will set done_index to
index, then find done is set, so will proceed to the end of the
function. When updating mapping->writeback_index for cyclic writeout,
we now use done_index == 0, so we're always cycling back to 0.
This seemed to be causing random mmap writes (slapadd and iozone) to
start writing more pages from the LRU and writeout would slowdown, and
caused bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=12604
about Berkeley DB slowing down dramatically.
With this patch, iozone random write performance is increased nearly
5x on my system (iozone -B -r 4k -s 64k -s 512m -s 1200m on ext2).
Signed-off-by: Nick Piggin <npiggin@suse.de> Reported-and-tested-by: Jan Kara <jack@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Takashi Iwai [Wed, 11 Feb 2009 23:06:42 +0000 (00:06 +0100)]
ALSA: mtpav - Fix initial value for input hwport
Fix the initial value for input hwport. The old value (-1) may cause
Oops when an realtime MIDI byte is received before the input port is
explicitly given.
Instead, now it's set to the broadcasting as default.
When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees. These are bothe well within the -55 - +125 degree
range for the sensor.
Fix overflow in left-shift of a u8.
Signed-off-by: Ian Dall <ian@beware.dropbear.id.au> Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This can also occur when an nbd device loses its nbd-client/server
connection. Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.
This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277
Testing would need to be performed to determine if the two issues are the
same.
This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.
The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request. This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.
Signed-off-by: Paul Clements <paul.clements@steeleye.com> Reported-by: Jon Nelson <jnelson-kernel-bugzilla@jamponi.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x, 2.6.28.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: rearrange exit_mmap() to unlock before arch_exit_mmap
Christophe Saout reported [in precursor to:
http://marc.info/?l=linux-kernel&m=123209902707347&w=4]:
> Note that I also some a different issue with CONFIG_UNEVICTABLE_LRU.
> Seems like Xen tears down current->mm early on process termination, so
> that __get_user_pages in exit_mmap causes nasty messages when the
> process had any mlocked pages. (in fact, it somehow manages to get into
> the swapping code and produces a null pointer dereference trying to get
> a swap token)
Jeremy explained:
Yes. In the normal case under Xen, an in-use pagetable is "pinned",
meaning that it is RO to the kernel, and all updates must go via hypercall
(or writes are trapped and emulated, which is much the same thing). An
unpinned pagetable is not currently in use by any process, and can be
directly accessed as normal RW pages.
As an optimisation at process exit time, we unpin the pagetable as early
as possible (switching the process to init_mm), so that all the normal
pagetable teardown can happen with direct memory accesses.
This happens in exit_mmap() -> arch_exit_mmap(). The munlocking happens
a few lines below. The obvious thing to do would be to move
arch_exit_mmap() to below the munlock code, but I think we'd want to
call it even if mm->mmap is NULL, just to be on the safe side.
Thus, this patch:
exit_mmap() needs to unlock any locked vmas before calling arch_exit_mmap,
as the latter may switch the current mm to init_mm, which would cause the
former to fail.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Cc: Christophe Saout <christophe@saout.de> Cc: Keir Fraser <keir.fraser@eu.citrix.com> Cc: Christophe Saout <christophe@saout.de> Cc: Alex Williamson <alex.williamson@hp.com> Cc: <stable@kernel.org> [2.6.28.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Wed, 11 Feb 2009 21:04:40 +0000 (13:04 -0800)]
parport: parport_serial, don't bind netmos ibm 0299
Since netmos 9835 with subids 0x1014(IBM):0x0299 is now bound with
serial/8250_pci, because it has no parallel ports and subdevice id isn't
in the expected form, return -ENODEV from probe function.
Heiko Carstens [Wed, 11 Feb 2009 21:04:38 +0000 (13:04 -0800)]
syscall define: fix uml compile bug
With the new system call defines we get this on uml:
arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x308): undefined reference to `sys_sigprocmask'
Reason for this is that uml passes the preprocessor option
-Dsigprocmask=kernel_sigprocmask to gcc when compiling the kernel.
This causes SYSCALL_DEFINE3(sigprocmask, ...) to be expanded to
SYSCALL_DEFINEx(3, kernel_sigprocmask, ...) and finally to a system
call named sys_kernel_sigprocmask. However sys_sigprocmask is missing
because of this.
To avoid macro expansion for the system call name just concatenate the
name at first define instead of carrying it through severel levels.
This was pointed out by Al Viro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by: WANG Cong <wangcong@zeuux.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Carsten Otte [Wed, 11 Feb 2009 21:04:37 +0000 (13:04 -0800)]
ext2/xip: refuse to change xip flag during remount with busy inodes
For a reason that I was unable to understand in three months of debugging,
mount ext2 -o remount stopped working properly when remounting from
regular operation to xip, or the other way around. According to a git
bisect search, the problem was introduced with the VM_MIXEDMAP/PTE_SPECIAL
rework in the vm:
In the failing scenario, the filesystem is mounted read only via root=
kernel parameter on s390x. During remount (in rc.sysinit), the inodes of
the bash binary and its libraries are busy and cannot be invalidated (the
bash which is running rc.sysinit resides on subject filesystem).
Afterwards, another bash process (running ifup-eth) recurses into a
subshell, runs dup_mm (via fork). Some of the mappings in this bash
process were created from inodes that could not be invalidated during
remount.
Both parent and child process crash some time later due to inconsistencies
in their address spaces. The issue seems to be timing sensitive, various
attempts to recreate it have failed.
This patch refuses to change the xip flag during remount in case some
inodes cannot be invalidated. This patch keeps users from running into
that issue.
[akpm@linux-foundation.org: cleanup] Signed-off-by: Carsten Otte <cotte@de.ibm.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Jared Hulbert <jaredeh@gmail.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Wed, 11 Feb 2009 21:04:36 +0000 (13:04 -0800)]
cgroups: fix lockdep subclasses overflow
I enabled all cgroup subsystems when compiling kernel, and then:
# mount -t cgroup -o net_cls xxx /mnt
# mkdir /mnt/0
This showed up immediately:
BUG: MAX_LOCKDEP_SUBCLASSES too low!
turning off the locking correctness validator.
It's caused by the cgroup hierarchy lock:
for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
struct cgroup_subsys *ss = subsys[i];
if (ss->root == root)
mutex_lock_nested(&ss->hierarchy_mutex, i);
}
Now we have 9 cgroup subsystems, and the above 'i' for net_cls is 8, but
MAX_LOCKDEP_SUBCLASSES is 8.
This patch uses different lockdep keys for different subsystems.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 11 Feb 2009 21:04:33 +0000 (13:04 -0800)]
kernel-doc: fix syscall wrapper processing
Fix kernel-doc processing of SYSCALL wrappers.
The SYSCALL wrapper patches played havoc with kernel-doc for
syscalls. Syscalls that were scanned for DocBook processing
reported warnings like this one, for sys_tgkill:
Warning(kernel/signal.c:2285): No description found for parameter 'tgkill'
Warning(kernel/signal.c:2285): No description found for parameter 'pid_t'
Warning(kernel/signal.c:2285): No description found for parameter 'int'
because the macro parameters all "look like" function parameters,
although they are not:
/**
* sys_tgkill - send signal to one specific thread
* @tgid: the thread group ID of the thread
* @pid: the PID of the thread
* @sig: signal to be sent
*
* This syscall also checks the @tgid and returns -ESRCH even if the PID
* exists but it's not belonging to the target process anymore. This
* method solves the problem of threads exiting and PIDs getting reused.
*/
SYSCALL_DEFINE3(tgkill, pid_t, tgid, pid_t, pid, int, sig)
{
...
This patch special-cases the handling SYSCALL_DEFINE* function
prototypes by expanding them to
long sys_foobar(type1 arg1, type1 arg2, ...)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Wed, 11 Feb 2009 21:04:31 +0000 (13:04 -0800)]
kernel-doc: preferred ending marker and examples
Fix kernel-doc-nano-HOWTO.txt to use */ as the ending marker in kernel-doc
examples and state that */ is the preferred ending marker.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Reported-by: Robert Love <robert.w.love@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MinChan Kim [Wed, 11 Feb 2009 21:04:27 +0000 (13:04 -0800)]
mm: fix mlocked page counter mismatch
When I tested following program, I found that the mlocked counter
is strange. It cannot free some mlocked pages.
It is because try_to_unmap_file() doesn't check real
page mappings in vmas.
That is because the goal of an address_space for a file is to find all
processes into which the file's specific interval is mapped. It is
related to the file's interval, not to pages.
Even if the page isn't really mapped by the vma, it returns SWAP_MLOCK
since the vma has VM_LOCKED, then calls try_to_mlock_page. After this the
mlocked counter is increased again.
COWed anon page in a file-backed vma could be a such case. This patch
resolves it.
Since journal_start_commit() is now fixed to return 1 when we started a
transaction commit, there's some transaction waiting to be committed or
there's a transaction already committing, we don't need to call
ext3_force_commit() in ext3_sync_fs(). Furthermore ext3_force_commit()
can unnecessarily create sync transaction which is expensive so it's
worthwhile to remove it when we can.
Cc: Eric Sandeen <sandeen@redhat.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Wed, 11 Feb 2009 21:04:25 +0000 (13:04 -0800)]
jbd: fix return value of journal_start_commit()
journal_start_commit() returns 1 if either a transaction is committing or
the function has queued a transaction commit. But it returns 0 if we
raced with somebody queueing the transaction commit as well. This
resulted in ext3_sync_fs() not functioning correctly (description from
Arthur Jones): In the case of a data=ordered umount with pending long
symlinks which are delayed due to a long list of other I/O on the backing
block device, this causes the buffer associated with the long symlinks to
not be moved to the inode dirty list in the second phase of fsync_super.
Then, before they can be dirtied again, kjournald exits, seeing the UMOUNT
flag and the dirty pages are never written to the backing block device,
causing long symlink corruption and exposing new or previously freed block
data to userspace.
This can be reproduced with a script created by Eric Sandeen
<sandeen@redhat.com>:
#!/bin/bash
umount /mnt/test2
mount /dev/sdb4 /mnt/test2
rm -f /mnt/test2/*
dd if=/dev/zero of=/mnt/test2/bigfile bs=1M count=512
touch /mnt/test2/thisisveryveryveryveryveryveryveryveryveryveryveryveryveryveryveryverylongfilename
ln -s /mnt/test2/thisisveryveryveryveryveryveryveryveryveryveryveryveryveryveryveryverylongfilename
/mnt/test2/link
umount /mnt/test2
mount /dev/sdb4 /mnt/test2
ls /mnt/test2/
This patch fixes journal_start_commit() to always return 1 when there's
a transaction committing or queued for commit.
Cc: Eric Sandeen <sandeen@redhat.com> Cc: Mike Snitzer <snitzer@gmail.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sven Wegener [Wed, 11 Feb 2009 21:04:23 +0000 (13:04 -0800)]
mm: fix dirty_bytes/dirty_background_bytes sysctls on 64bit arches
We need to pass an unsigned long as the minimum, because it gets casted
to an unsigned long in the sysctl handler. If we pass an int, we'll
access four more bytes on 64bit arches, resulting in a random minimum
value.
[rientjes@google.com: fix type of `old_bytes'] Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: Christoph Lameter <cl@linux-foundation.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Wed, 11 Feb 2009 21:04:23 +0000 (13:04 -0800)]
gx1fb: properly alloc cmap and plug cmap leak
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Marco La Porta <marco-laporta@tiscali.it> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andres Salomon [Wed, 11 Feb 2009 21:04:22 +0000 (13:04 -0800)]
gxfb: properly alloc cmap and plug cmap leak
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Marco La Porta <marco-laporta@tiscali.it> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marco La Porta [Wed, 11 Feb 2009 21:04:20 +0000 (13:04 -0800)]
lxfb: properly alloc cmap in all cases and don't leak the memory
We weren't properly allocating the cmap for depths greater than 8bpp,
which caused pain for things like DirectFB. Also, we never freed the cmap
memory upon module unload..
[dilinger@debian.org: dropped unnecessary code and clean up patch]
[dilinger@debian.org: add error checking and handling] Signed-off-by: Andres Salomon <dilinger@debian.org> Cc: Jordan Crouse <jordan@cosmicpenguin.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Wed, 11 Feb 2009 16:34:16 +0000 (16:34 +0000)]
Do not account for hugetlbfs quota at mmap() time if mapping [SHM|MAP]_NORESERVE
Commit 5a6fe125950676015f5108fb71b2a67441755003 brought hugetlbfs more
in line with the core VM by obeying VM_NORESERVE and not reserving
hugepages for both shared and private mappings when [SHM|MAP]_NORESERVE
are specified. However, it is still taking filesystem quota
unconditionally.
At fault time, if there are no reserves and attempt is made to allocate
the page and account for filesystem quota. If either fail, the fault
fails. The impact is that quota is getting accounted for twice. This
patch partially reverts 5a6fe125950676015f5108fb71b2a67441755003. To
help prevent this mistake happening again, it improves the documentation
of hugetlb_reserve_pages()
Reported-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Acked-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reinette Chatre [Tue, 10 Feb 2009 20:02:49 +0000 (12:02 -0800)]
iwlwifi: fix suspend/resume and its usage of pci saved state
Here we do two things:
First, revert "iwlwifi: save PCI state before suspend, restore after
resume". That misguided patch led to being unable to use iwlwifi
devices after resume.
Next, indicate to PCI driver that the saved PCI state is valid during suspend.
We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.
PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Tested-by: Alex Riesen <fork0@users.sf.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung [Wed, 4 Feb 2009 23:40:43 +0000 (23:40 +0000)]
zd1211rw: treat MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for TP-Link WN322/422G
Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Tested-by: Petr Mensik <pihhan@cipis.net> Tested-by: Stephen Ho <stephenhoinhk@gmail.com> Tested-by: Ismael Ojeda Perez <iojedaperez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hin-Tak Leung [Sun, 8 Feb 2009 02:13:56 +0000 (02:13 +0000)]
zd1211rw: adding 0ace:0xa211 as a ZD1211 device
Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Tested-by: Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 5 Feb 2009 23:27:32 +0000 (00:27 +0100)]
mac80211: restrict to AP in outgoing interface heuristic
We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: stable@kernel.org [2.6.28.x] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Sat, 10 Jan 2009 19:42:54 +0000 (14:42 -0500)]
ath5k: fix bf->skb==NULL panic in ath5k_tasklet_rx
Under memory pressure, we may not be able to allocate a new skb for
new packets. If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.
Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Linus Torvalds [Wed, 11 Feb 2009 16:24:32 +0000 (08:24 -0800)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix TIMER_ABSTIME for process wide cpu timers
timers: split process wide cpu clocks/timers, fix
x86: clean up hpet timer reinit
timers: split process wide cpu clocks/timers, remove spurious warning
timers: split process wide cpu clocks/timers
signal: re-add dead task accumulation stats.
x86: fix hpet timer reinit for x86_64
sched: fix nohz load balancer on cpu offline
Linus Torvalds [Wed, 11 Feb 2009 16:23:22 +0000 (08:23 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace, x86: fix the usage of ptrace_fork()
i8327: fix outb() parameter order
x86: fix math_emu register frame access
x86: math_emu info cleanup
x86: include correct %gs in a.out core dump
x86, vmi: put a missing paravirt_release_pmd in pgd_dtor
x86: find nr_irqs_gsi with mp_ioapic_routing
x86: add clflush before monitor for Intel 7400 series
x86: disable intel_iommu support by default
x86: don't apply __supported_pte_mask to non-present ptes
x86: fix grammar in user-visible BIOS warning
x86/Kconfig.cpu: make Kconfig help readable in the console
x86, 64-bit: print DMI info in the oops trace
Peter Zijlstra [Wed, 11 Feb 2009 10:30:27 +0000 (11:30 +0100)]
timers: fix TIMER_ABSTIME for process wide cpu timers
The POSIX timer interface allows for absolute time expiry values through the
TIMER_ABSTIME flag, therefore we have to synchronize the timer to the clock
every time we start it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Tue, 10 Feb 2009 15:37:31 +0000 (16:37 +0100)]
timers: split process wide cpu clocks/timers, fix
To decrease the chance of a missed enable, always enable the timer when we
sample it, we'll always disable it when we find that there are no active timers
in the jiffy tick.
This fixes a flood of warnings reported by Mike Galbraith.
Reported-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stefan Weinhuber [Wed, 11 Feb 2009 09:37:31 +0000 (10:37 +0100)]
[S390] dasd: fix race in dasd timer handling
In dasd_device_set_timer and dasd_block_set_timer we interpret the
return value of mod_timer in a wrong way. If the timer expires in
the small window between our check of timer_pending and the call to
mod_timer, then the timer will be set, mod_timer returns zero and
we will call add_timer for a timer that is already pending.
As del_timer and mod_timer do all the necessary checking themselves,
we can simplify our code and remove the race a the same time.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vdso_per_cpu_data entry in the lowcore structure uses __u32
instead of __u64. If the data page is above 4GB the pointer is
truncated and the kernel crashes.
Reported-by: Mijo Safradin <mijo@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Oleg Nesterov [Mon, 9 Feb 2009 01:02:33 +0000 (02:02 +0100)]
ptrace, x86: fix the usage of ptrace_fork()
I noticed by pure accident we have ptrace_fork() and friends. This was
added by "x86, bts: add fork and exit handling", commit bf53de907dfdaac178c92d774aae7370d7b97d20.
I can't test this, ds_request_bts() returns -EOPNOTSUPP, but I strongly
believe this needs the fix. I think something like this program
Steven Rostedt [Tue, 10 Feb 2009 16:53:23 +0000 (11:53 -0500)]
tracing, x86: fix constraint for parent variable
The constraint used for retrieving and restoring the parent function
pointer is incorrect. The parent variable is a pointer, and the
address of the pointer is modified by the asm statement and not
the pointer itself. It is incorrect to pass it in as an output
constraint since the asm will never update the pointer.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Wu Fengguang [Wed, 11 Feb 2009 07:22:29 +0000 (15:22 +0800)]
ALSA: hda - enable HDMI audio pin out at module loading time
We found that enabling/disabling HDMI audio pin out at stream start/stop
time will kill the leading 500ms or so sound samples. Avoid this by enabling
pin out once and for ever at module loading time.
The leading ~500ms audio samples will still be lost when switching from
X-channel playback to Y-channel playback where X != Y. However there's no
much we can do about it: the audio infoframe has to change and it looks like
either G45 or YAMAHA requires some time to switch the configuration.
Wu Fengguang [Wed, 11 Feb 2009 07:22:28 +0000 (15:22 +0800)]
ALSA: hda - allow multi-channel HDMI audio playback when ELD is not present
The YAMAHA AV-X1800 requires audio infoframe to include speaker-channel
mapping to play >2 channel HDMI audio. In theory that mapping should be
derived from its speaker configurations contained in its ELD. However we
currently cannot get ELD in console before the KMS functionalities are ready.
This is a more or less general issue at least in the near future. As a
workaround, we propose to allow playback of mult-channel audio when ELD
is not available.
powerpc/mm: Rework usage of _PAGE_COHERENT/NO_CACHE/GUARDED
broke setting of the _PAGE_COHERENT bit in the PPC HW PTE. Since we now
actually set _PAGE_COHERENT in the Linux PTE we shouldn't be clearing it
out before we propogate it to the PPC HW PTE.
Reported-by: Martyn Welch <martyn.welch@gefanuc.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Meelis Roos [Wed, 11 Feb 2009 01:29:42 +0000 (17:29 -0800)]
sunhme: Fix Quattro HME irq registration on proble failures
Currently, the sunhme driver installs SBus Quattro interrupt handler
when at least one HME card was initialized correctly and at least one
Quattro card is present. This breaks when a Quattro card fails
initialization for whatever reason - IRQ is registered and OOPS happens
when it fires.
The solution, as suggested by David Miller, was to keep track which
cards of the Quattro bundles have been initialized, and request/free the
Quattro IRQ only when all four devices have been successfully
initialized.
The patch only touches SBus initialization - PCI init already resets the
card pointer to NULL on init failure.
The patch has been tested on Sun E3500 with SBus and PCI single HME
cards and one PCI Quattro HME card in a situation where any PCI card
failed init when the SBus routines tried to init them by mistake.
Additionally it replaces Quattro request_irq panic with error return -
if this card fails to work, at least let the others work.
Tested on E450 with PCI HME and PCI Quad HME.
[ Minor coding style fixups -DaveM ]
Signed-off-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Meelis Roos [Wed, 11 Feb 2009 01:19:19 +0000 (17:19 -0800)]
fore200: fix oops on failed firmware load
Fore 200 ATM driver fails to handle request_firmware failures and oopses
when no firmware file was found. Fix it by checking for the right return
values and propaganting the return value up.
Signed-off-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 10 Feb 2009 23:54:50 +0000 (15:54 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] AACI: timeout will reach -1
[ARM] Storage class should be before const qualifier
[ARM] pxa: stop and disable IRQ for each DMA channels at startup
[ARM] pxa: make more SSCR0 bit definitions visible on multiple processors
[ARM] pxa: fix missing of __REG() definition for ac97 registers access
[ARM] pxa: fix NAND and MMC clock initialization for pxa3xx
projects / linux-2.6-omap-h63xx.git / log