Yinghai Lu [Sun, 29 Mar 2009 19:30:05 +0000 (12:30 -0700)]
PCI: fix HT MSI mapping fix
Impact: fix bug
This patch reworks the nv_msi_ht_cap_quirk() and will only try to avoid
to enable ht_msi on device following that root dev, and don't touch that
root dev, but only do that trick with end_device on the chain.
Yinghai Lu [Sat, 21 Mar 2009 02:29:41 +0000 (19:29 -0700)]
PCI: don't enable too much HT MSI mapping
Impact: fix bug
Prakash reported that his c51-mcp51 system ondie sound card doesn't work
MSI but if he hack out the HT-MSI on mcp51, the MSI will work well with
sound card.
This patch reworks nv_msi_ht_cap_quirk() and will only avoid enabling
ht_msi on devices following that root device.
Yinghai Lu [Wed, 25 Mar 2009 20:26:13 +0000 (13:26 -0700)]
x86/PCI: make pci=lastbus=255 work when acpi is on
Impact: scan more peer root buses even acpi is used
Move pci_bios_fixup_peer_bridges out of pci_legacy_init and into
pci_subsys_init. This allows pci_bios_fixup_peer_bridges to be called
even pci_apci_init is driving PCI initialization.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yu Zhao [Sun, 15 Feb 2009 18:55:47 +0000 (02:55 +0800)]
PCI: save and restore PCIe 2.0 registers
PCIe 2.0 defines several new registers (Device Control 2, Link Control 2,
and Slot Control 2). Save and retore them in pci_save_pcie_state() and
pci_restore_pcie_state().
Kenji Kaneshige [Thu, 26 Mar 2009 07:49:52 +0000 (16:49 +0900)]
PCI: fix kernel oops on bridge removal
Fix the following kernel oops problem that happens when removing PCI
bridge with pciehp loaded. It should also occur with other hotplug
driver that is implemented as a bridge's driver.
The pci_remove_bus_device() removes all buses and devices under the
bridge, and then removes the bridge. So the remove() callback of the
hotplug drivers implemented as a bridge's driver is executed after the
struct pci_bus of the bridge's secondary bus is removed. The remove()
callback of those driver unregisters the slot using pci_destroy_slot(),
and slot's release callback refers to the the struct pci_bus that was
already freed. This is the cause of the kernel oops.
This patch solves the problem by stopping bus drivers before removing the
bridge and its child bus and devices.
Alex Chiang [Fri, 20 Mar 2009 20:56:51 +0000 (14:56 -0600)]
PCI Hotplug: rename legacy_fakephp to fakephp
We wanted to replace fakephp wholesale, so rename legacy_fakephp back
to fakephp. Yes, this is a silly commit, but it produces a much easier
patch to read and review.
Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Trent Piepho [Fri, 20 Mar 2009 20:56:46 +0000 (14:56 -0600)]
PCI Hotplug: restore fakephp interface with complete reimplementation
A complete re-implementation of fakephp is necessary if it is to
present its former interface (pre-2.6.27, when it broke). The
reason is that PCI hotplug drivers call pci_hp_register(), which
enforces the rule that only one /sys/bus/pci/slots/ file may be
created per physical slot.
The change breaks the old fakephp's assumption that it could
create a file per function. So we re-implement fakephp to avoid
using the standard PCI hotplug API so that we can restore the old
fakephp user interface.
It puts entries in /sys/bus/pci/slots with the names of all PCI
devices/functions, exactly symmetrical to what is shown in
/sys/bus/pci/devices. Each slots/ entry has a "power" attribute,
which works the same way as the fakephp driver's power attribute
has worked.
There are a few improvements over old fakephp, which couldn't handle
PCI devices being added or removed via a means outside of
fakephp's knowledge. If a device was added another way, old fakephp
didn't notice and didn't create the fake slot for it. If a
device was removed another way, old fakephp didn't delete the fake
slot for it (and accessing the stale slot caused an oops).
The new implementation overcomes these limitations. As a
consequence, removing a bridge with other devices behind it now
works as well, which is something else old fakephp couldn't do
previously.
This duplicates a tiny bit of the code in the PCI core that does
this same function. Re-using that code ends up being more
complex than duplicating it, and it makes code in the PCI core
more ugly just to support this legacy fakephp interface
compatibility layer.
Reviewed-by: James Cameron <qz@hp.com> Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Alex Chiang [Fri, 20 Mar 2009 20:56:41 +0000 (14:56 -0600)]
PCI: Introduce /sys/bus/pci/devices/.../rescan
This interface allows the user to force a rescan of the device's
parent bus and all subordinate buses, and rediscover devices removed
earlier from this part of the device tree.
Alex Chiang [Fri, 20 Mar 2009 20:56:36 +0000 (14:56 -0600)]
PCI: Introduce /sys/bus/pci/devices/.../remove
This patch adds an attribute named "remove" to a PCI device's sysfs
directory. Writing a non-zero value to this attribute will remove the PCI
device and any children of it.
Trent Piepho wrote the original implementation and documentation.
Thanks to Vegard Nossum for testing under kmemcheck and finding locking
issues with the sysfs interface.
Alex Chiang [Fri, 20 Mar 2009 20:56:10 +0000 (14:56 -0600)]
PCI: always scan child buses
While scanning bridges, we stop our scan if we encounter a bus
that we've seen before, to work around some buggy chipsets. This
is a good idea, but prevents us from fully scanning the PCI bus
at a future time (to find newly hot-added devices, for example).
Change the logic so that we skip _re-adding_ an existing bus
that we've seen before, but also allow the scan to descend to
all child buses.
Now that we're potentially scanning our child buses again, we
also need to be sure not to attempt re-initializing their BARs
so we avoid that.
This patch lays the groundwork to allow the user to issue a
rescan of the PCI bus at any time.
Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Trent Piepho [Fri, 20 Mar 2009 20:56:05 +0000 (14:56 -0600)]
PCI: pci_scan_slot() returns newly found devices
pci_scan_slot() has been rewritten to be less complex and will now
return the number of *new* devices found.
Existing callers need not worry because they already assume that
they can't call pci_scan_slot() on an already-scanned slot.
Thus, there is no semantic change for existing callers: returning
newly found devices (this patch) is exactly equal to returning all
found devices (before this patch).
This patch adds some more groundwork to allow us to rescan the
PCI bus during runtime to discover newly added devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Reviewed-by: Alex Chiang <achiang@hp.com> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Trent Piepho [Fri, 20 Mar 2009 20:56:00 +0000 (14:56 -0600)]
PCI: don't scan existing devices
pci_scan_single_device is supposed to add newly discovered
devices to pci_bus->devices, but doesn't check to see if the
device has already been added. This can cause problems if we ever
want to use this interface to rescan the PCI bus.
Kenji Kaneshige [Fri, 20 Mar 2009 20:55:55 +0000 (14:55 -0600)]
PCI: pci_is_root_bus helper
Introduce pci_is_root_bus helper function. This will help make code
more consistent, as well as prevent incorrect assumptions (such as
pci_bus->self == NULL on a root bus, which is not always true).
Yinghai Lu [Fri, 20 Mar 2009 03:55:35 +0000 (20:55 -0700)]
x86/PCI: host mmconfig detect clean up
Fix mmconfig detection to not assume a single mmconfig space in the
northbridge, paving the way for AMD fam10h + mcp55 CPUs. On those, the
MSR has some range, but the mcp55 pci config will have another one.
Also helps the mcp55 + io55 case, where every one will have one range.
If it is mcp55, exclude the range that is used by CPU MSR, in other
words , if the CPU claims busses 0-255, the range in mcp55 is dropped,
because CPU HW will not route those ranges to mcp55 mmconfig to handle
it.
Signed-off-by: Yinghai Lu <yinghai.lu@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ed Swierk [Fri, 20 Mar 2009 03:57:56 +0000 (20:57 -0700)]
x86/PCI: Detect mmconfig on nVidia MCP55
Detect and enable memory-mapped PCI configuration space on the nVidia
MCP55 southbridge. Tested against 2.6.27.4 on an Arista Networks
development board with one MCP55, Coreboot firmware, no ACPI.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yu Zhao [Fri, 20 Mar 2009 03:25:15 +0000 (11:25 +0800)]
PCI: add SR-IOV API for Physical Function driver
Add or remove the Virtual Function when the SR-IOV is enabled or
disabled by the device driver. This can happen anytime rather than
only at the device probe stage.
Yu Zhao [Fri, 20 Mar 2009 03:25:11 +0000 (11:25 +0800)]
PCI: initialize and release SR-IOV capability
If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.
David O'Shea [Mon, 2 Mar 2009 08:51:13 +0000 (09:51 +0100)]
PCI: Compaq Evo D510 SMBus quirk using USB instead of VGA
On the Compaq Evo D510 SFF/CMT, a PCI quirk activated the SMBus device
based on detection of the on-board VGA controller, but the on-board
VGA is disabled if an AGP card is inserted, so look for one of the USB
controllers instead.
Signed-off-by: David O'Shea <dcoshea@hotmail.com> Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Dave Airlie [Wed, 4 Mar 2009 05:57:05 +0000 (05:57 +0000)]
PCI: expose boot VGA device via sysfs.
X really would like to know which VGA device was considered the boot
device by the system. The x86 PCI fixups have support for discovering
this but we provide no way to expose it to userspace.
This adds a sysfs file per VGA class device which has the value 0 for
non the boot device or unknown, and 1 if the VGA device is the boot
device.
Yinghai Lu [Mon, 9 Mar 2009 04:35:37 +0000 (21:35 -0700)]
PCI/x86: detect host bridge config space size w/o using quirks
Many host bridges support a 4k config space, so check them directy
instead of using quirks to add them.
We only need to do this extra check for host bridges at this point,
because only host bridges are known to have extended address space
without also having a PCI-X/PCI-E caps. Other devices with this
property could be done with quirks (if there are any).
As a bonus, we can remove the quirks for AMD host bridges with family
10h and 11h since they're not needed any more.
With this patch, we can get correct pci cfg size of new Intel CPUs/IOHs
with host bridges.
Signed-off-by: Yinghai Lu <yinghai@kernel.org> Acked-by: H. Peter Anvin <hpa@zytor.com> Reviewed-by: Matthew Wilcox <willy@linux.intel.com> Cc: <stable@kernel.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Alex Chiang [Mon, 9 Mar 2009 18:08:15 +0000 (12:08 -0600)]
PCI: PCIe portdrv: eliminate double kfree in remove path
Commit 55633af3 (PCIe portdrv: Use driver data to simplify code)
added a kfree of the driver private data in pcie_port_device_remove
but forgot to remove the old kfree from pcie_portdrv_remove.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yuji Shimada [Mon, 16 Mar 2009 08:13:39 +0000 (17:13 +0900)]
PCI: allow assignment of memory resources with a specified alignment
This patch allows memory resources to be assigned with a specified
alignment at boot-time or run-time. The patch is useful when we use PCI
pass-through, because page-aligned memory resources are required to
securely share PCI resources with guest drivers.
If you want to assign the resource at boot time, please set
"pci=resource_alignment=" boot parameter.
This is format of "pci=resource_alignment=" boot parameter:
[<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
Specifies alignment and device to reassign
aligned memory resources.
If <order of align> is not specified, PAGE_SIZE is
used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
If you want to assign the resource at run-time, please set
"/sys/bus/pci/resource_alignment" file, and hot-remove the device and
hot-add the device. For this purpose, fakephp or PCI hotplug interfaces
can be used.
The format of "/sys/bus/pci/resource_alignment" file is the same with
boot parameter. You can use "," instead of ";".
Matthew Wilcox [Tue, 17 Mar 2009 12:54:10 +0000 (08:54 -0400)]
PCI MSI: Add support for multiple MSI
Add the new API pci_enable_msi_block() to allow drivers to
request multiple MSI and reimplement pci_enable_msi in terms of
pci_enable_msi_block. Ensure that the architecture back ends don't
have to know about multiple MSI.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Matthew Wilcox [Tue, 17 Mar 2009 12:54:09 +0000 (08:54 -0400)]
PCI MSI: Refactor interrupt masking code
Since most of the callers already know whether they have an MSI or
an MSI-X capability, split msi_set_mask_bits() into msi_mask_irq()
and msix_mask_irq(). The only callers which don't (mask_msi_irq()
and unmask_msi_irq()) can share code in msi_set_mask_bit(). This then
becomes the only caller of msix_flush_writes(), so we can inline it.
The flushing read can be to any address that belongs to the device,
so we can eliminate the calculation too.
We can also get rid of maskbits_mask from struct msi_desc and simply
recalculate it on the rare occasion that we need it. The single-bit
'masked' element is replaced by a copy of the 32-bit 'masked' register,
so this patch does not affect the size of msi_desc.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Matthew Wilcox [Tue, 17 Mar 2009 12:54:07 +0000 (08:54 -0400)]
PCI MSI: msi_desc->dev is always initialised
By passing the pci_dev into alloc_msi_entry() we can be sure that
the ->dev entry is always assigned and so we don't need to check it.
Also, we used kzalloc() so we don't need to initialise ->irq to 0.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Matthew Wilcox [Tue, 17 Mar 2009 12:54:06 +0000 (08:54 -0400)]
PCI MSI: Replace 'type' with 'is_msix'
By changing from a 5-bit field to a 1-bit field, we free up some bits
that can be used by a later patch. Also rearrange the fields for better
packing on 64-bit platforms (reducing the size of msi_desc from 72 bytes
to 64 bytes).
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Chris Wright [Tue, 24 Feb 2009 05:52:23 +0000 (21:52 -0800)]
PCI: add remove_id sysfs entry
This adds a remove_id sysfs entry to allow users of new_id to later
remove the added dynid. One use case is management tools that want to
dynamically bind/unbind devices to pci-stub driver while devices are
assigned to KVM guests. Rather than having to track which driver was
originally bound to the driver, a mangement tool can simply:
Guest uses device
Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kenji Kaneshige [Tue, 17 Feb 2009 05:16:13 +0000 (14:16 +0900)]
PCI: fix wrong assumption in pci_common_swizzle
Current pci_common_swizzle() seems to have a assumption that
pci_bus->self is NULL on the pci root bus. But it might not be true on
some platforms. Because of this wrong assumption, pci_common_swizzle()
might cause endless loop. We must check pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:15:45 +0000 (14:15 +0900)]
PCI: fix wrong assumption in pci_get_interrupt_pin
Current pci_get_interrupt_pin() seems to have an assumption that
pci_bus->self is NULL on the root pci bus. But it might not be true on
some platforms. Because of this wrong assumption, current
pci_get_interrupt_pin() might cause endless loop. We must check
pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:15:16 +0000 (14:15 +0900)]
PCI: fix wrong assumption in pci_read_bridge_bases
Current pci_read_bridge_bases() has an assumption that pci_bus->self
is NULL on the pci root bus (It checks pci_bus->self to see if the pci
bus is root bus). But is might not true on some platforms. We must
check pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:14:36 +0000 (14:14 +0900)]
PCI: fix wrong assumption in pci_find_upstream_pcie_bridge
Current pci_find_upstream_pcie_bridge() has a wrong assumption that
pci_bus->self is NULL on the root pci bus. But it might not true on
some platforms. Because of this wrong assumption, current
pci_find_upstream_pcie_bridge() might cause endless loop. We must
check pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:13:59 +0000 (14:13 +0900)]
PCI hotplug: fix wrong assumption in acpi_get_hp_hw_control_from_firmware
Current acpi_get_hp_hw_control_from_firmware() has a assumption that
pci_bus->self is NULL on a PCI root bus. But it might not be true on
some platforms. Because of this wrong assumption, current
acpi_get_hp_hw_control_from_firmware() might cause endless loop. We
must check pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:13:20 +0000 (14:13 +0900)]
PCI hotplug: fix wrong assumption in acpi_get_hp_params_from_firmware
Current acpi_get_hp_params_from_firmware() has a assumption that
pci_bus->self is NULL on the root pci bus. But it might not true on
some platforms. Because of this wrong assumption, current
acpi_get_hp_params_from_firmware() might cause endless loop. We must
check pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:12:36 +0000 (14:12 +0900)]
PCI/ACPI: fix wrong assumption in acpi_find_root_bridge_handle
Current acpi_find_root_bridge_handle() has a assumption that
pci_bus->self is NULL on the root pci bus. But it might not be true on
some platforms. Because of this wrong assumption, current
acpi_find_root_bridge_handle() might cause endless loop. We must check
pci_bus->parent instead.
Kenji Kaneshige [Tue, 17 Feb 2009 05:11:56 +0000 (14:11 +0900)]
PCI/ACPI: fix wrong assumption in acpi_pci_get_bridge_handle
Current acpi_pci_get_bridge_handle() has an assumption that
pci_bus->self is NULL on the root pci bus. But it might not true on
some platforms. Because of this wrong assumption, current
acpi_pci_get_bridge_handle() might return improper ACPI handle. We
must check pci_bus->parent instead.
This bug is the root cause of the following kernel panic reported by
James Bottomley. This problem was introduced by the commit e8c331e963c58b83db24b7d0e39e8c07f687dbc6. The immediate cause was
acpi_pci_get_bridge_handle() returned NULL unexpectedly and it was
passed as the second argument of acpi_walk_namespace().
Ivan Kokshaysky [Tue, 17 Feb 2009 10:46:53 +0000 (13:46 +0300)]
PCI/alpha: pci sysfs resources
This closes http://bugzilla.kernel.org/show_bug.cgi?id=10893
which is a showstopper for X development on alpha.
The generic HAVE_PCI_MMAP code (drivers/pci-sysfs.c) is not
very useful since we have to deal with three different types
of MMIO address spaces: sparse and dense mappings for old
ev4/ev5 machines and "normal" 1:1 MMIO space (bwx) for ev56 and
later.
Also "write combine" mappings are meaningless on alpha - roughly
speaking, alpha does write combining, IO reordering and other
optimizations by default, unless user splits IO accesses
with memory barriers.
I think the cleanest way to deal with resource files on alpha
is to convert the default no-op pci_create_resource_files() and
pci_remove_resource_files() for !HAVE_PCI_MMAP case into __weak
functions and override them with alpha specific ones.
Another alpha hook is needed for "legacy_" resource files
to handle sparse addressing (pci_adjust_legacy_attr).
With the "standard" resourceN files on ev56/ev6 libpciaccess
works "out of the box". Handling of resourceN_sparse/resourceN_dense
files on older machines obviously requires some userland work.
Sparse/dense stuff has been tested on sx164 (pca56/pyxis, normally
uses bwx IO) with the kernel hacked into "cia compatible" mode.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Andrew Morton [Wed, 18 Feb 2009 18:44:29 +0000 (10:44 -0800)]
PCI: constify pci_bus_assign_resources()
drivers/pci/hotplug/fakephp.c: In function 'pci_rescan_bus':
drivers/pci/hotplug/fakephp.c:271: warning: passing argument 1 of 'pci_bus_assign_resources' discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Michael Ellerman [Wed, 11 Feb 2009 11:27:02 +0000 (22:27 +1100)]
PCI/MSI: Allow arch code to return the number of MSI-X available
There is code in msix_capability_init() which, when the requested number
of MSI-X couldn't be allocated, calculates how many MSI-X /could/ be
allocated and returns that to the driver. That allows the driver to then
make a second request, with a number of MSIs that should succeed.
The current code requires the arch code to setup as many msi_descs as it
can, and then return to the generic code. On some platforms the arch
code may already know how many MSI-X it can allocate, before it sets up
any of the msi_descs.
So change the logic such that if the arch code returns a positive error
code, that is taken to be the number of MSI-X that could be allocated.
If the error code is negative we still calculate the number available
using the old method.
Because it's a little subtle, make sure the error return code from
arch_setup_msi_irq() is always negative. That way only implementations
of arch_setup_msi_irqs() need to be careful about returning a positive
error code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Roel Kluin [Wed, 11 Feb 2009 20:13:45 +0000 (21:13 +0100)]
PCI hotplug: shpchp: fix bus number check to avoid false positive
With for (busnr = 0; busnr <= end; busnr++) { ... } busnr reaches end + 1
after the loop. So fix the "no busses available" check to look for just
busnr > end rather than >=.
Kenji Kaneshige [Mon, 9 Feb 2009 06:59:29 +0000 (15:59 +0900)]
PCI/ACPI: move _OSC code to pci_root.c
Move PCI _OSC management code from drivers/pci/pci-acpi.c to
drivers/acpi/pci_root.c. The benefits are
- We no longer need struct osc_data and its management code (contents
are moved to struct acpi_pci_root). This simplify the code, and we
no longer care about kmalloc() failure.
- We can make pci_acpi_osc_support() be a static function, which is
called only from drivers/acpi/pci_root.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Reviewed-by: Andrew Patterson <andrew.patterson@hp.com> Tested-by: Andrew Patterson <andrew.patterson@hp.com> Acked-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Alex Chiang [Wed, 4 Feb 2009 18:25:22 +0000 (11:25 -0700)]
PCI: enhance physical slot debug information
Convert usages of pr_debug to dev_dbg and add physical slot name.
Note that we use dev_dbg on the struct pci_bus and still manually
print out the PCI slot number (instead of calling dev_dbg on a
pci_dev) because a struct pci_bus with empty physical slots will
not have any pci_devs.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com> Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kenji Kaneshige [Tue, 3 Feb 2009 06:06:16 +0000 (15:06 +0900)]
PCI: pciehp: enable software notification on empty slots
Current pciehp disables software notification of adapter presence
changed event and MRL changed event when slot is turned off. Because
of this, there is no way to detect those events on empty slots in the
current pciehp implementation.
According to the past discussion(*), this behavior was introduced to
prevent endless loop that could happen if pcie_isr() runs after power
fault is detected on a certain platform whose stickey power-fault bit
remains on till the slot is powered on again.
I think this endless loop can be avoided using one bit flag that
indicates power fault had been detected, instead of disabling software
notification of adapter present changed event and MRL changed event.
With this patch, we can enable software notification mechanism of
presence changed and MRL changed event on the empty slots again.
Kenji Kaneshige [Tue, 3 Feb 2009 06:06:13 +0000 (15:06 +0900)]
PCI: pciehp: fix possible endless loop in pcie_isr
Fix possible endless loop in pcie_isr.
Currently, pcie_isr() (interrupt service routine of pciehp) can end up in an
endless loop if the Slot Status register is set again immediately after being
cleared. According to the past discussion (see below URL) this case can happen
if the power fault detected bit is set during handling.
Julia Lawall [Sun, 8 Feb 2009 21:45:24 +0000 (22:45 +0100)]
PCI: introduce missing kfree
Error handling code following a kmalloc should free the allocated data.
Since the subsequent code that could provoke an error does not use the
allocated data, the allocation is just moved below it.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
Frank Seidel [Fri, 6 Feb 2009 09:23:36 +0000 (10:23 +0100)]
PCI: add missing KERN_* constants to printks
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing pieces here for the pci subsystem.
Michael Ellerman [Mon, 19 Jan 2009 00:31:00 +0000 (11:31 +1100)]
PCI/MSI: Use #ifdefs instead of weak functions
Weak functions aren't all they're cracked up to be. They lead to
incorrect binaries with some toolchains, they require us to have empty
functions we otherwise wouldn't, and the unused code is not elided
(as of gcc 4.3.2 anyway).
So replace the weak MSI arch hooks with the #define foo foo idiom. We no
longer need empty versions of arch_setup/teardown_msi_irq().
This is less source (by 1 line!), and results in smaller binaries too:
If MSI-X interrupt mode is used by the PCI Express port driver, too
many vectors are allocated and it is not ensured that the right
vectors will be used for the right services. Namely, the PCI Express
specification states that both PCI Express native PME and PCI Express
hotplug will always use the same MSI or MSI-X message for signalling
interrupts, which implies that the same vector will be used by both
of them. Also, the VC service does not use interrupts at all.
Moreover, is not clear which of the vectors allocated by
pci_enable_msix() in the current code will be used for PME and
hotplug and which of them will be used for AER if all of these
services are configured.
For these reasons, rework the allocation of interrupts for PCI
Express ports so that if MSI-X are enabled, the right vectors will be
used for the right purposes.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCI Express port driver uses 'struct pcie_port_service_id' for
matching port service devices and drivers, but this structure
contains fields that duplicate information from the port device
itself (vendor, device, subvendor, subdevice) and fields that are not
used by any existing port service driver (class, class_mask,
drvier_data). Also, both existing port service drivers (AER and
PCIe HP) don't even use the vendor and device fields for device
matching. Therefore 'struct pcie_port_service_id' can be removed
altogether and the only useful members of it (port_type, service) can
be introduced directly into the port service device and port service
driver structures. That simplifies the code quite a bit and reduces
its size.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI: PCIe portdrv: Do not enable port device before setting up interrupts
The PCI Express port driver calls pci_enable_device() before setting
up interrupts, which is wrong, because if there is an interrupt pin
configured for the port, pci_enable_device() will likely set up an
interrupt link for it. However, this shouldn't be done if either
MSI or MSI-X interrupt mode is chosen for the port.
The solution is to call pci_enable_device() after setting up
interrupts, because in that case the interrupt link won't be set up
if MSI or MSI-X are enabled.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI: PCIe portdrv: Aviod using service devices with wrong interrupts
The PCI Express port driver should not attempt to register service
devices that require the ability to generate interrupts if generating
interrupts is not possible. Namely, if the port has no interrupt pin
configured and we cannot set up MSI or MSI-X for it, there is no way
it can generate interrupts and in such a case the port services that
rely on interrupts (PME, PCIe HP, AER) should not be enabled for it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI: PCIe portdrv: Use driver data to simplify code
PCI Express port driver extension, as defined by struct
pcie_port_device_ext in portdrv.h, is allocated and initialized, but
never used (it also is never freed). Extend it to hold the PCI Express
port type as well as the port interrupt mode, change its name and use it
to simplify the code in portdrv_core.c .
Additionally, remove the redundant interrupt_mode member of struct
pcie_device defined in include/linux/pcieport_if.h .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bjorn Helgaas [Wed, 14 Jan 2009 17:04:25 +0000 (10:04 -0700)]
PCI/x86: make early dump handle multi-function devices
The early "dump PCI config space" code skips many multi-function
devices. This patch fixes that, so it dumps all devices in PCI
domain 0.
We should not skip the rest of the functions if CLASS_REVISION is
0xffffffff. Often multi-function devices have gaps in the function ID
space, e.g., 1c.0 and 1c.2 exist but 1c.1 doesn't. The CLASS_REVISION
of the non-existent 1c.1 function will appear to be 0xffffffff.
We should only look at the HEADER_TYPE of function zero. Often the
"multi-function" is set in function zero, but not in other functions.
Linus Torvalds [Wed, 18 Mar 2009 14:39:11 +0000 (07:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Fix vunmap and free order in snd_free_sgbuf_pages()
ALSA: mixart, fix lock imbalance
ALSA: pcm_oss, fix locking typo
ALSA: oss-mixer - Fixes recording gain control
ALSA: hda - Workaround for buggy DMA position on ATI controllers
ALSA: hda - Fix DMA mask for ATI controllers
ALSA: opl3sa2 - Fix NULL dereference when suspending snd_opl3sa2
Takashi Iwai [Tue, 17 Mar 2009 13:00:06 +0000 (14:00 +0100)]
ALSA: Fix vunmap and free order in snd_free_sgbuf_pages()
In snd_free_sgbuf_pags(), vunmap() is called after releasing the SG
pages, and it causes errors on Xen as Xen manages the pages
differently. Although no significant errors have been reported on
the actual hardware, this order should be fixed other way round,
first vunmap() then free pages.
Cc: Jan Beulich <jbeulich@novell.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
projects / linux-2.6-omap-h63xx.git / log