This is a driver for Nortel emobility PCI adaptors, which consist of an
Orinoco compatible PCMCIA card and a simple PCI-to-PCMCIA bridge. The
driver initializes the device and uses Orinoco core driver for actual
wireless networking. Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
It is not supported by this driver because it has no firmware in
flash. spectrum_cs is needed for this device. Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Change orinoco_translate_scan() to return error code on error.
Adjust the caller to check for errors and clean up if needed. Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
mv643xx_eth_get_config_reg() was reading the wrong register.
mv643xx_eth_set_config_reg() was or'ing instead of setting the
register. These functions are trivial and both are called only from
mv643xx_eth_set_rx_mode() when changing to/from promiscuous mode.
Remove both functions and do the operations directly in
mv643xx_eth_set_rx_mode().
Also, maintain promiscuous mode setting across port resets.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch corrects the accounting of outstanding tx skbs. It fixes
a bug that causes "Error on Queue Full" messages seen since scatter-gather
was enabled by using the hardware tcp/udp checksum generator.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes an skb memory leak under heavy receive load
(whenever the more packets have been received than the NAPI budget
allows to be processed).
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The sis191 is the gigabit brother of the sis190. SiS's driver suggests
that the register set is backward compatible: this should hopefully
give a basic driver.
The device should allow the usual features from a modern ethernet
adapter (802.1q, SG, Jumbo frames, TSO, checksum offload). So far
the relevant register layout is not documented. SiS's driver does
not provide these features either (at least not for Linux).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] sis190: make 10Mbps the default when handling the StationControl register
This patch does three things:
- widen the access to the StationControl register (note the SIS_W16
versus SIS_W32 change);
- default to 10Mbps half duplex when the LPA can not be evaluated
(reg31->ctl is identical for both). It can be argued that it makes
sense as the lowest common denominator when everything else failed.
Btw it works better than the current code. :o)
- remove some enums: they do not document anymore.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH] sis190: recent chipsets from SiS include a RGMII
Extracted from SiS's GPLed driver. From the few pdf available at SiS's,
it seems that the 965 and the 966 south bridge include this interface
whereas the 965L (and anything below) does not. It is expected to be a
sis191 related feature and should not hurt the existing sis190 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Peter Chubb [Sat, 3 Sep 2005 21:05:06 +0000 (14:05 -0700)]
[PATCH] 'mdio_bus_exit' in discarded section .text.exit
When building with CONFIG_PHYLIB=y on Itanium, I see:
`mdio_bus_exit' referenced in section `.init.text' of
drivers/built-in.o: defined in discarded section `.exit.text' of
drivers/built-in.o
I believe that mdio_bus_exit should not be declared __exit, because it is
referencesd from __init sections in, say, phy_init().
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Adrian Bunk [Sat, 3 Sep 2005 21:04:55 +0000 (14:04 -0700)]
[PATCH] drivers/net/ne3210.c: cleanups
- make two needlessly global functions static
- kill an ancient version variable
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On s390 the lock value used for spinlocks consists of the lower 32 bits of the
PSW that holds the lock. If this address happens to be on a four gigabyte
boundary the lock is left unlocked. This allows other cpus to grab the same
lock and enter a lock protected code path concurrently. In theory this can
happen if the vmalloc area for the code of a module crosses a 4 GB boundary.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a race in pfault_interrupt. That function gets called two times for
each pfault notification. Once with a subcode of 0 to indicate that a real
page is not available and once with a subcode of 0x80 to indicate that the
page is present again.
Since the two external interrupts can be delivered on two different cpus the
order in which the two calls are made is unpredictable. It is possible that
the subcode 0x80 interrupt is completed before the subcode 0x00 interrupt has
done the wake_up() call.
To avoid calling wake_up() on an already removed task structure proper task
structure reference counting is needed. Increase the reference counter in the
subcode 0x00 interrupt before setting pfault_wait to zero and return the
reference after the wake_up call.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Collect the irb at the correct subchannel when waiting for the clear
interrupt during subchannel cleaning befor reIPL - don't stop at the first
interrupt that comes in.
- Change "extern __inline__" to "static inline".
- Remove unneeded qdio includes.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for diag 250 access to dasd devices for 64 bit kernels. In
addition fix detach/attach for diag disks. The VM control block needs to get
recreated by a call to mdsk_init_io.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reintroduce a read-only copy of the devmap features in the device struct.
This is necessary to solve a deadlock on the dasd_devmap_lock which is
acquired by dasd_get_features called from the dasd tasklet. The current
implementation of devmap doesn't allow to call any devmap function from
interrupt or softirq context.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new machine check handler still has a few bugs.
1) The system entry time has to be stored in the machine check handler,
2) the machine check return psw may not be stored at the usual place
because it might overwrite the return psw of the interrupted context,
3) the return address for the call to s390_handle_mcck in the i/o interrupt
handler is not correct,
4) the system call cleanup has to take the different save area of the
machine check handler into account,
5) the machine check handler may not call UPDATE_VTIME before
CREATE_STACK_FRAME, and
6) the io leave path needs a critical section cleanup to make sure that the
TIF_MCCK_PENDING bit is really checked before switching back to user space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:51 +0000 (15:57 -0700)]
[PATCH] uml: fix advanced sysemu check
cleanup and fix the check for advanced sysemu (PTRACE_SYSEMU_SINGLESTEP
option)
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:51 +0000 (15:57 -0700)]
[PATCH] uml: allow host capability usage to be disabled
Add new cmdline setups:
- noprocmm
- noptracefaultinfo
In case of testing, they can be used to switch off usage of
/proc/mm and PTRACE_FAULTINFO independently.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:50 +0000 (15:57 -0700)]
[PATCH] uml: skas0 stubs now check system call return values
Change syscall-stub's data to include a "expected retval".
Stub now checks syscalls retval and aborts execution of syscall list, if
retval != expected retval.
run_syscall_stub prints the data of the failed syscall, using the data pointer
and retval written by the stub to the beginning of the stack.
one_syscall_stub is removed, to simplify code, because only some instructions
are saved by one_syscall_stub, no host-syscall.
Using the stub with additional data (modify_ldt via stub)
is prepared also.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:49 +0000 (15:57 -0700)]
[PATCH] uml: increase granularity of host capability checking
This change enables SKAS0/SKAS3 to work with all combinations of /proc/mm and
PTRACE_FAULTINFO being available or not.
Also it changes the initialization of proc_mm and ptrace_faultinfo slightly,
to ease forcing SKAS0 on a patched host. Forcing UML to run without /proc/mm
or PTRACE_FAULTINFO by cmdline parameter can be implemented with a setup
resetting the related variable.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:46 +0000 (15:57 -0700)]
[PATCH] uml: add host AIO support to block driver
This adds AIO support to the ubd driver.
The driver breaks a struct request into IO requests to the host, based on the
hardware segments in the request and on any COW blocks covered by the request.
The ubd IO thread is gone, since there is now an equivalent thread in the AIO
module.
There is provision for multiple outstanding requests now. Requests aren't
retired until all pieces of it have been completed. The AIO requests have a
shared count, which is decremented as IO operations come in until it reaches
0. This can be possibly moved to the request struct - haven't looked at this
yet.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:45 +0000 (15:57 -0700)]
[PATCH] uml: use host AIO support
This patch makes UML use host AIO support when it (and
/usr/include/linux/aio_abi.h) are present. This is only the support, with no
consumers - a consumer is coming in the next patch.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sat, 3 Sep 2005 22:57:43 +0000 (15:57 -0700)]
[PATCH] uml: build cleanups
Added missing include list to uml AFLAGS
Killed magic for stubs. [So] - it was needed only because of messed AFLAGS
Switched segv_stubs.c to kernel CFLAGS sans profile, instead of user ones
Killed STUBS_CFLAGS - it's not needed and the only remaining use had been
gratitious - it only polluted CFLAGS
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:41 +0000 (15:57 -0700)]
[PATCH] uml: merge duplicated page table code
There is a lot of code which is duplicated between the 2 and 3 level
implementation, with the only difference that the 3-level implementation is a
bit more generalized (instead of accessing directly pte_t.pte, it uses the
appropriate access macros).
So this code is joined together.
As obvious, a "core code nice cleanup" is not a "stability-friendly patch" so
usual care applies.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:36 +0000 (15:57 -0700)]
[PATCH] uml: TLB operation batching
This adds VM op batching to skas0. Rather than having a context switch to and
from the userspace stub for each address space change, we write a number of
operations to the stub data page and invoke a different stub which loops over
them and executes them all in one go.
The operations are stored as [ system call number, arg1, arg2, ... ] tuples.
The set is terminated by a system call number of 0. Single operations, i.e.
page faults, are handled in the old way, since that is slightly more
efficient.
For a kernel build, a minority (~1/4) of the operations are part of a set.
These sets averaged ~100 in length, so for this quarter, the context switching
overhead is greatly reduced.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:34 +0000 (15:57 -0700)]
[PATCH] uml: remove duplicated exports
Al Viro <viro@parcelfarce.linux.theplanet.co.uk> spotted a bunch of duplicated
exports - this removes them.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:33 +0000 (15:57 -0700)]
[PATCH] uml: mark SMP on UML/x86_64 as broken
Noticed by Al Viro <viro@parcelfarce.linux.theplanet.co.uk> - SMP on x86_64 is
fundamentally broken due to UML's reuse of the host arch's percpu stuff. This
is OK on x86, but the x86_64 pda stuff just won't work for UML.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sat, 3 Sep 2005 22:57:31 +0000 (15:57 -0700)]
[PATCH] uml: remove libc reference in build
Remove an unneeded reference to libc.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sat, 3 Sep 2005 22:57:30 +0000 (15:57 -0700)]
[PATCH] uml: build cleanup
Build cleanups
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:29 +0000 (15:57 -0700)]
[PATCH] uml: error path cleanup
This cleans up the error path in ubd_open, causing it now to call ubd_close
appropriately when something fails.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid chomping low bits of address for functions doing it by themselves,
fix whitespace, add a correctness checking.
I did this for remap-file-pages protection support, it was useful on its
own too.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: fixes performance regression in activate_mm and thus exec()
Normally, activate_mm() is called from exec(), and thus it used to be a
no-op because we use a completely new "MM context" on the host (for
instance, a new process), and so we didn't need to flush any "TLB entries"
(which for us are the set of memory mappings for the host process from the
virtual "RAM" file).
Kernel threads, instead, are usually handled in a different way. So, when
for AIO we call use_mm(), things used to break and so Benjamin implemented
activate_mm(). However, that is only needed for AIO, and could slow down
exec() inside UML, so be smart: detect being called for AIO (via
PF_BORROWED_MM) and do the full flush only in that situation.
Comment also the caller so that people won't go breaking UML without
noticing. I also rely on the caller's locks for testing current->flags.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> CC: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:24 +0000 (15:57 -0700)]
[PATCH] uml: fix SIGWINCH handler race while waiting for signals.
If a SIGWINCH comes in, while winch_thread() isn't waiting in wait(),
winch_thread could miss signals. It isn't very probable, that anyone will
see this causing trouble, as it would need a very special timing, that a
missed SIGWINCH results in a wrong window size.
So, this is a minor problem. But why not fix, as it can be done so easy?
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Apparently, GDB gets confused when we do an execvp() on ourselves.
Since it's simply done to allocate further space for command line arguments
(which we'll use to allow gathering the startup command line for guest
processes through the host), allow the user to disable that to get a
debuggable UML binary.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up to "UML Support - Ptrace: adds the host SYSEMU support, for
UML and general usage" (i.e. uml-support-* in current mm).
Avoid unconditionally jumping to work_pending and code copying, just reuse
the already existing resume_userspace path.
One interesting note, from Charles P. Wright, suggested that the API is
improvable with no downsides for UML (except that it will have to support
yet another host API, since dropping support for the current API, for UML,
is not reasonable from users' point of view).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> CC: Charles P. Wright <cwright@cs.sunysb.edu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
This is simply an adjustment for "Ptrace - i386: fix Syscall Audit interaction
with singlestep" to work on top of SYSEMU patches, too. On this patch, I have
some doubts: I wonder why we need to alter that way ptrace_disable().
I left the patch this way because it has been extensively tested, but I don't
understand the reason.
The current PTRACE_DETACH handling simply clears child->ptrace; actually this
is not enough because entry.S just looks at the thread_flags; actually,
do_syscall_trace checks current->ptrace but I don't think depending on that is
good, at least for performance, so I think the clearing is done elsewhere.
For instance, on PTRACE_CONT it's done, but doing PTRACE_DETACH without
PTRACE_CONT is possible (and happens when gdb crashes and one kills it
manually).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> CC: Roland McGrath <roland@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:20 +0000 (15:57 -0700)]
[PATCH] Uml support: add PTRACE_SYSEMU_SINGLESTEP option to i386
This patch implements the new ptrace option PTRACE_SYSEMU_SINGLESTEP, which
can be used by UML to singlestep a process: it will receive SINGLESTEP
interceptions for normal instructions and syscalls, but syscall execution will
be skipped just like with PTRACE_SYSEMU.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:19 +0000 (15:57 -0700)]
[PATCH] Uml support: reorganize PTRACE_SYSEMU support
With this patch, we change the way we handle switching from PTRACE_SYSEMU to
PTRACE_{SINGLESTEP,SYSCALL}, to free TIF_SYSCALL_EMU from double use as a
preparation for PTRACE_SYSEMU_SINGLESTEP extension, without changing the
behavior of the host kernel.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] UML Support - Ptrace: adds the host SYSEMU support, for UML and general usage
Jeff Dike <jdike@addtoit.com>,
Paolo 'Blaisorblade' Giarrusso <blaisorblade_spam@yahoo.it>,
Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Adds a new ptrace(2) mode, called PTRACE_SYSEMU, resembling PTRACE_SYSCALL
except that the kernel does not execute the requested syscall; this is useful
to improve performance for virtual environments, like UML, which want to run
the syscall on their own.
In fact, using PTRACE_SYSCALL means stopping child execution twice, on entry
and on exit, and each time you also have two context switches; with SYSEMU you
avoid the 2nd stop and so save two context switches per syscall.
Also, some architectures don't have support in the host for changing the
syscall number via ptrace(), which is currently needed to skip syscall
execution (UML turns any syscall into getpid() to avoid it being executed on
the host). Fixing that is hard, while SYSEMU is easier to implement.
* This version of the patch includes some suggestions of Jeff Dike to avoid
adding any instructions to the syscall fast path, plus some other little
changes, by myself, to make it work even when the syscall is executed with
SYSENTER (but I'm unsure about them). It has been widely tested for quite a
lot of time.
* Various fixed were included to handle the various switches between
various states, i.e. when for instance a syscall entry is traced with one of
PT_SYSCALL / _SYSEMU / _SINGLESTEP and another one is used on exit.
Basically, this is done by remembering which one of them was used even after
the call to ptrace_notify().
* We're combining TIF_SYSCALL_EMU with TIF_SYSCALL_TRACE or TIF_SINGLESTEP
to make do_syscall_trace() notice that the current syscall was started with
SYSEMU on entry, so that no notification ought to be done in the exit path;
this is a bit of a hack, so this problem is solved in another way in next
patches.
* Also, the effects of the patch:
"Ptrace - i386: fix Syscall Audit interaction with singlestep"
are cancelled; they are restored back in the last patch of this series.
Detailed descriptions of the patches doing this kind of processing follow (but
I've already summed everything up).
* Fix behaviour when changing interception kind #1.
In do_syscall_trace(), we check the status of the TIF_SYSCALL_EMU flag
only after doing the debugger notification; but the debugger might have
changed the status of this flag because he continued execution with
PTRACE_SYSCALL, so this is wrong. This patch fixes it by saving the flag
status before calling ptrace_notify().
* Fix behaviour when changing interception kind #2:
avoid intercepting syscall on return when using SYSCALL again.
A guest process switching from using PTRACE_SYSEMU to PTRACE_SYSCALL
crashes.
The problem is in arch/i386/kernel/entry.S. The current SYSEMU patch
inhibits the syscall-handler to be called, but does not prevent
do_syscall_trace() to be called after this for syscall completion
interception.
The appended patch fixes this. It reuses the flag TIF_SYSCALL_EMU to
remember "we come from PTRACE_SYSEMU and now are in PTRACE_SYSCALL", since
the flag is unused in the depicted situation.
* Fix behaviour when changing interception kind #3:
avoid intercepting syscall on return when using SINGLESTEP.
When testing 2.6.9 and the skas3.v6 patch, with my latest patch and had
problems with singlestepping on UML in SKAS with SYSEMU. It looped
receiving SIGTRAPs without moving forward. EIP of the traced process was
the same for all SIGTRAPs.
What's missing is to handle switching from PTRACE_SYSCALL_EMU to
PTRACE_SINGLESTEP in a way very similar to what is done for the change from
PTRACE_SYSCALL_EMU to PTRACE_SYSCALL_TRACE.
I.e., after calling ptrace(PTRACE_SYSEMU), on the return path, the debugger is
notified and then wake ups the process; the syscall is executed (or skipped,
when do_syscall_trace() returns 0, i.e. when using PTRACE_SYSEMU), and
do_syscall_trace() is called again. Since we are on the return path of a
SYSEMU'd syscall, if the wake up is performed through ptrace(PTRACE_SYSCALL),
we must still avoid notifying the parent of the syscall exit. Now, this
behaviour is extended even to resuming with PTRACE_SINGLESTEP.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 3 Sep 2005 22:57:13 +0000 (15:57 -0700)]
[PATCH] Ptrace/i386: fix "syscall audit" interaction with singlestep
Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Avoid giving two traps for singlestep instead of one, when syscall auditing is
enabled.
In fact no singlestep trap is sent on syscall entry, only on syscall exit, as
can be seen in entry.S:
# Note that in this mask _TIF_SINGLESTEP is not tested !!! <<<<<<<<<<<<<<
testb $(_TIF_SYSCALL_TRACE|_TIF_SYSCALL_AUDIT|_TIF_SECCOMP),TI_flags(%ebp)
jnz syscall_trace_entry
...
syscall_trace_entry:
...
call do_syscall_trace
But auditing a SINGLESTEP'ed process causes do_syscall_trace to be called, so
the tracer will get one more trap on the syscall entry path, which it
shouldn't.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> CC: Roland McGrath <roland@redhat.com> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 3 Sep 2005 22:57:12 +0000 (15:57 -0700)]
[PATCH] uml: Rename Kconfig files to be like the other arches
To the extent that sub-Kconfig files exist elsewhere in the tree, they are
named Kconfig.foo, rather than the Kconfig_foo that UML has. This patch
brings the names in line with the rest of the tree.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Sat, 3 Sep 2005 22:57:10 +0000 (15:57 -0700)]
[PATCH] m68k: cleanup inline mem functions
Use the builtin functions for memset/memclr/memcpy, special optimizations for
page operations have dedicated functions now. Uninline memmove/memchr and
move all functions into a single file and clean it up a little.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Sat, 3 Sep 2005 22:57:09 +0000 (15:57 -0700)]
[PATCH] m68k: move cache functions into separate file
Move a few cache functions into its own file and fix flush_icache_range() so
it can handle both kernel and user addresses correctly (assuming context is
set correctly).
Turn copy_to_user_page/copy_from_user_page into inline functions and add a
missing cache flush.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Sat, 3 Sep 2005 22:57:08 +0000 (15:57 -0700)]
[PATCH] m68k: sys_ptrace cleanup
- create helper function singlestep_disable()
- move variable definitions to the top of the function
- use "out_eio" label as common error destination
- don't clear failure value for PTRACE_SETREGS/PTRACE_GETREGS
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Shaohua Li [Sat, 3 Sep 2005 22:57:07 +0000 (15:57 -0700)]
[PATCH] add suspend/resume for timer
The timers lack .suspend/.resume methods. Because of this, jiffies got a
big compensation after a S3 resume. And then softlockup watchdog reports
an oops. This occured with HPET enabled, but it's also possible for other
timers.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Sat, 3 Sep 2005 22:57:05 +0000 (15:57 -0700)]
[PATCH] pm: fix process freezing
If process freezing fails, some processes are frozen, and rest are left in
"were asked to be frozen" state. Thats wrong, we should leave it in some
consistent state.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Sat, 3 Sep 2005 22:57:05 +0000 (15:57 -0700)]
[PATCH] swsusp: fix error handling and cleanups
Drop printing during normal boot (when no image exists in swap), print
message when drivers fail, fix error paths and consolidate near-identical
functions in disk.c (and functions with just one statement).
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michal Schmidt [Sat, 3 Sep 2005 22:57:02 +0000 (15:57 -0700)]
[PATCH] swsusp: simpler calculation of number of pages in PBE list
The function calc_nr uses an iterative algorithm to calculate the number of
pages needed for the image and the pagedir. Exactly the same result can be
obtained with a one-line expression.
Note that this was even proved correct ;-).
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz> Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch protects from leaking sensitive data after resume from suspend.
During suspend a temporary key is created and this key is used to encrypt the
data written to disk. When, during resume, the data was read back into memory
the temporary key is destroyed which simply means that all data written to
disk during suspend are then inaccessible so they can't be stolen lateron.
Think of the following: you suspend while an application is running that keeps
sensitive data in memory. The application itself prevents the data from being
swapped out. Suspend, however, must write these data to swap to be able to
resume lateron. Without suspend encryption your sensitive data are then
stored in plaintext on disk. This means that after resume your sensitive data
are accessible to all applications having direct access to the swap device
which was used for suspend. If you don't need swap after resume these data
can remain on disk virtually forever. Thus it can happen that your system
gets broken in weeks later and sensitive data which you thought were encrypted
and protected are retrieved and stolen from the swap device.
Signed-off-by: Andreas Steinmetz <ast@domdv.de> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Sat, 3 Sep 2005 22:56:58 +0000 (15:56 -0700)]
[PATCH] fix pm_message_t stuff in -mm tree
This should bits from -mm tree that are affected by pm_message_t
conversion. [I'm not 100% sure I got all of them, but I certainly got all
the errors on make allyesconfig build, and most of warnings, too. I'll go
through the buildlog tommorow and fix any remaining bits].
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Sat, 3 Sep 2005 22:56:57 +0000 (15:56 -0700)]
[PATCH] swsusp: switch pm_message_t to struct
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Alexander Nyberg <alexn@telia.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pavel Machek [Sat, 3 Sep 2005 22:56:56 +0000 (15:56 -0700)]
[PATCH] swsusp: fix remaining u32 vs. pm_message_t confusion
Fix remaining bits of u32 vs. pm_message confusion. Should not break
anything.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6-omap-h63xx.git / log