Magnus Damm [Fri, 13 Mar 2009 15:36:55 +0000 (15:36 +0000)]
video: sh_mobile_lcdcfb suspend/resume support
This patch adds suspend/resume support to the LCDC
driver for SuperH Mobile - sh_mobile_lcdcfb.
We simply stop hardware on suspend and start it again
on resume. For RGB panels this is trivial, but for SYS
panels in deferred io mode this becomes a bit more
difficult - we need to wait for a frame end interrupt
to make sure the clocks are balanced before stopping
the actual hardware.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 13 Mar 2009 15:23:04 +0000 (15:23 +0000)]
sh: SuperH Mobile suspend support
This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 11 Mar 2009 08:14:26 +0000 (08:14 +0000)]
sh: improve sh7785lcr power off code
Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.
This removes the serial port garbage printout.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the Sega Dreamcast visual memory unit as a
flash mapping. It requires changes in the maple bus driver (posted
separately) to support block reads and writes.
The VMU is a 'smart' flash device, with a built-in 8-bit controller -
for instance there is an erase before a write but it is hidden from the
user. But the device's overall behaviour means it works well with the
mtd layer and it is appropriate to add it as an mtd mapping.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk> Acked-By: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: Support fixed 32-bit PMB mappings from bootloader.
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 10 Mar 2009 06:24:21 +0000 (06:24 +0000)]
input: add suspend wakeup support to sh_keysc
This patch adds wakeup support to the sh_keysc driver.
With this feature the ".../power/wakeup" file can be
used to enable and disable if the device takes the
system out of suspend. Default is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Tue, 10 Mar 2009 06:08:49 +0000 (06:08 +0000)]
video: deferred io cleanup fix for sh_mobile_lcdcfb
Fix deferred io cleanup patch in the sh_mobile_lcdcfb driver.
If probe() fails early the sh_mobile_lcdc_stop() function will
be called to clean up deferred io. This patch modifies the
code to only call fb_deferred_io_cleanup() after deferred io
has been initialized.
With this patch applied we no longer hit BUG_ON() inside
fb_deferred_io_cleanup(). Triggers on a Migo-R with the
SYS QVGA panel board unmounted.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh: Add media/soc_camera.h to board setup of Renesas AP325RXA
Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4d76f83213e379b12df504269d21c9e7c) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CLONE_PARENT can fool the ->self_exec_id/parent_exec_id logic. If we
re-use the old parent, we must also re-use ->parent_exec_id to make
sure exit_notify() sees the right ->xxx_exec_id's when the CLONE_PARENT'ed
task exits.
Also, move down the "p->parent_exec_id = p->self_exec_id" thing, to place
two different cases together.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Howells <dhowells@redhat.com> Cc: Serge E. Hallyn <serge@hallyn.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
p54: fix race condition in memory management
cfg80211: test before subtraction on unsigned
iwlwifi: fix error flow in iwl*_pci_probe
rt2x00 : more devices to rt73usb.c
rt2x00 : more devices to rt2500usb.c
bonding: Fix device passed into ->ndo_neigh_setup().
vlan: Fix vlan-in-vlan crashes.
net: Fix missing dev->neigh_setup in register_netdevice().
tmspci: fix request_irq race
pkt_sched: act_police: Fix a rate estimator test.
tg3: Fix 5906 link problems
SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
IPv6: add "disable" module parameter support to ipv6.ko
sungem: another error printed one too early
aoe: error printed 1 too early
net pcmcia: worklimit reaches -1
net: more timeouts that reach -1
net: fix tokenring license
dm9601: new vendor/product IDs
netlink: invert error code in netlink_set_err()
...
Chris Mason [Mon, 9 Mar 2009 15:45:38 +0000 (11:45 -0400)]
Btrfs: fix spinlock assertions on UP systems
btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places. But, it wasn't correct for UP compiled
kernels.
This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Reason for this is that cpu time accounting usually only happens from
interrupt context, but acct_update_integrals gets also called from
process context with interrupts enabled.
So in acct_update_integrals we may end up with the following scenario:
Between reading tsk->stime/tsk->utime and tsk->acct_timexpd an interrupt
happens which updates accouting values. This causes acct_timexpd to be
greater than the former stime + utime. The subsequent calculation of
dtime = cputime_sub(time, tsk->acct_timexpd);
will be negative and the division performed by
cputime_to_jiffies(dtime)
will generate an exception since the result won't fit into a 32 bit
register.
In order to fix this just always disable interrupts while accessing any
of the accounting values.
Reported by: Frans Pop <elendil@planet.nl>
Tested by: Frans Pop <elendil@planet.nl> Cc: stable@kernel.org Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 8 Mar 2009 17:27:13 +0000 (10:27 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
x86, bts: remove bad warning
x86: add Dell XPS710 reboot quirk
x86, math-emu: fix init_fpu for task != current
x86: EFI: Back efi_ioremap with init_memory_mapping instead of FIX_MAP
x86: fix DMI on EFI
Linus Torvalds [Sun, 8 Mar 2009 17:24:39 +0000 (10:24 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (28 commits)
Blackfin arch: SPI_MMC is now mainlined MMC_SPI
Blackfin arch: disable legacy /proc/scsi/ support by default
Blackfin arch: remove duplicated ANOMALY_05000448 ifdef check
Blackfin arch: add stubs for anomalies 447 and 448
Blackfin arch: cleanup bfin_sport.h header and export it to userspace
Blackfin arch: fix bug - gdb signull case make trunk kernel panic frequently
Blackfin arch: remove spurious dash when dcache is off
Blackfin arch: mark init_pda as __init as only __init funcs all it
Blackfin arch: fix bug - On bf548-ezkit, ethernet fails to work after wakeup from "mem"
Blackfin arch: Random read/write errors are a bad thing
Blackfin arch: update default kernel config, select KSZ8893M driver for BF518
Blackfin arch: Fix bug - KGDB single step into the middle of a 4 bytes instruction on bf561 after soft bp is hit
Blackfin arch: Fix bug - make ksz8893m driver available when bfin_mac is enabled
Blackfin arch: make sure people do not set the kernel load address too high
Blackfin arch: fix bug - The SPORT_HYS bit is not set for BF561 0.5
Blackfin arch: update anomaly sheets to match latest public info
Blackfin arch: Fix BUG - kernel fails to build in pm.c when allow wakeup fromi standby by GPIO
Blackfin arch: PM_BFIN_WAKE_GP: update help
Blackfin arch: fix bug - kgdb fails to continue after setting breakpoint on bf561-ezkit kernel with smp patch
Blackfin arch: Enable Write Back Cache on all Blackfin Boards
...
Linus Torvalds [Sun, 8 Mar 2009 17:23:05 +0000 (10:23 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmatest: fix use after free in dmatest_exit
ipu_idmac: fix spinlock type
iop-adma, mv_xor: fix mem leak on self-test setup failure
fsldma: fix off by one in dma_halt
I/OAT: fail self-test if callback test reaches timeout
I/OAT: update driver version and copyright dates
I/OAT: list usage cleanup
I/OAT: set tcp_dma_copybreak to 256k for I/OAT ver.3
I/OAT: cancel watchdog before dma remove
I/OAT: fail initialization on zero channels detection
I/OAT: do not set DCACTRL_CMPL_WRITE_ENABLE for I/OAT ver.3
I/OAT: add verification for proper APICID_TAG_MAP setting by BIOS
dmaengine: update kerneldoc
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ata: add CFA specific identify data words
remove stale comment from <linux/hdreg.h>
AT91: initialize Compact Flash on AT91SAM9263 cpu
ide: add at91_ide driver
ide: allow to wrap interrupt handler
ide-iops: fix odd-length ATAPI PIO transfers
ide: NULL noise: drivers/ide/ide-*.c
ide: expiry() returns int, negative expiry() return values won't be noticed
Linus Torvalds [Sun, 8 Mar 2009 17:22:01 +0000 (10:22 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't trust current capacity values in identify words 57-58
libata: make sure port is thawed when skipping resets
sata_nv: fix module parameter description
ahci: Add the Device IDs for MCP89 and remove IDs of MCP7B to/from ahci.c
libata: don't use on-stack sense buffer
libata: align ap->sector_buf
libata: fix dma_unmap_sg misuse
libata: change drive ready wait after hard reset to 5s
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: frag_size should be signed, as it can hold an error result
Squashfs: fix documentation typo, Cramfs filesystem limit is 256 MiB
Squashfs: Fix oops when reading fsfuzzer corrupted filesystems
Linus Torvalds [Sun, 8 Mar 2009 17:03:31 +0000 (10:03 -0700)]
Merge branch 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
ALSA: hda - Fix typos in slave controls in patch_sigmatel.c
Ralf Baechle [Thu, 5 Mar 2009 10:45:48 +0000 (11:45 +0100)]
MIPS: compat: Implement is_compat_task.
This is a build fix required after "x86-64: seccomp: fix 32/64 syscall
hole" (commit 5b1017404aea6d2e552e991b3fd814d839e9cd67). MIPS doesn't
have the issue that was fixed for x86-64 by that patch.
This also doesn't solve the N32 issue which is that N32 seccomp processes
will be treated as non-compat processes thus only have access to N64
syscalls.
Markus Metzger [Thu, 5 Mar 2009 07:57:21 +0000 (08:57 +0100)]
x86, pebs: correct qualifier passed to ds_write_config() from ds_request_pebs()
ds_write_config() can write the BTS as well as the PEBS part of
the DS config. ds_request_pebs() passes the wrong qualifier, which
results in the wrong configuration to be written.
Markus Metzger [Thu, 5 Mar 2009 07:49:54 +0000 (08:49 +0100)]
x86, bts: remove bad warning
In case a ptraced task is reaped (while the tracer is still attached),
ds_exit_thread() is called before ptrace_exit(). The latter will
release the bts_tracer and remove the thread's ds_ctx.
The former will WARN() if the context is not NULL.
Oleg Nesterov submitted patches that move ptrace_exit() before
exit_thread() and thus reverse the order of the above calls.
Remove the bad warning. I will add it again when Oleg's changes are in.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305084954.A22000@sedona.ch.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Takashi Iwai [Fri, 6 Mar 2009 08:43:58 +0000 (09:43 +0100)]
ALSA: hda - Fix headphone-detect regression with multiple HP jacks
The recent changes over the DAC detection mechanism in patch_sigmatel.c
breaks the HP detection on the machines with multiple HP jacks.
It's basically because of the workaround to support the multi-channel
output. Since the HP detection is more important feature, disable
the HP-swap workaroud temporarily.
Jens Axboe [Fri, 6 Mar 2009 07:55:24 +0000 (08:55 +0100)]
block: fix missing bio back/front segment size setting in blk_recount_segments()
Commit 1e42807918d17e8c93bf14fbb74be84b141334c1 introduced a bug where we
don't get front/back segment sizes in the bio in blk_recount_segments().
Fix this by tracking the back bio as well as the front bio in
__blk_recalc_rq_segments(), this also cleans up the interface by getting
rid of the segment size pointer passing.
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The tick rate define (ORION5X_TCLK) was removed in favor of a runtime
detection. The quick fix is to add the define in the watchdog driver.
The fix is not correct for all supported orion5x platforms, but since
the supported platforms right now are 133 Mhz and 166 Mhz, it won't
be _that_ far off. ;-) A fix that uses the runtime-determined timer
tick rate will be applied later.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: Kristof Provost <kristof@sigsegv.be> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Nicolas Pitre <nico@cam.org> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org>
Reinette Chatre [Tue, 3 Mar 2009 19:37:04 +0000 (11:37 -0800)]
iwlwifi: fix error flow in iwl*_pci_probe
Both the agn and 3945 drivers has some problems with dealing with
errors in their probe functions. Ensure that a goto will undo only
things that was done before the goto was called.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
add more usb_dev to rt73usb.c . IDs 'stolen' from the
windows inf file(10/21/2008, 1.03.02.0000) plus some
from the Ralink linux driver(2009_0206_RT73_Linux_STA_Drv1.1.0.2.tar.bz2)
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Cc: Andrew Victor <avictor.za@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.
Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Cc: Andrew Victor <avictor.za@gmail.com> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Thu, 5 Mar 2009 15:10:56 +0000 (16:10 +0100)]
ide-iops: fix odd-length ATAPI PIO transfers
Commit 9567b349f7e7dd7e2483db99ee8e4a6fe0caca38 (ide: merge ->atapi_*put_bytes
and ->ata_*put_data methods) introduced a regression WRT the odd-length ATAPI
PIO transfers -- the final word didn't get written (causing command timeouts).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Hannes Eder [Thu, 5 Mar 2009 15:10:56 +0000 (16:10 +0100)]
ide: NULL noise: drivers/ide/ide-*.c
Fix this sparse warnings:
drivers/ide/ide-disk_proc.c:130:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-floppy_proc.c:32:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-proc.c:234:11: warning: Using plain integer as NULL pointer
drivers/ide/ide-tape.c:2141:11: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net> Cc: trivial@kernel.org Cc: kernel-janitors@vger.kernel.org Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
bart:
It seems like the bug could cause insanely long timeouts for:
- ATA_DMA_ERR error in dma_timer_expiry()
- commands without ->expiry in tc86c001_timer_expiry()
(TC86C001 IDE controller only)
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: port it to the current tree] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Robert Hancock [Tue, 17 Feb 2009 02:15:08 +0000 (20:15 -0600)]
libata: Don't trust current capacity values in identify words 57-58
Hanno Böck reported a problem where an old Conner CP30254 240MB hard drive
was reported as 1.1TB in capacity by libata:
http://lkml.org/lkml/2009/2/13/134
This was caused by libata trusting the drive's reported current capacity in
sectors in identify words 57 and 58 if the drive does not support LBA and the
current CHS translation values appear valid. Unfortunately it seems older
ATA specs were vague about what this field should contain and a number of drives
used values with wrong byte order or that were totally bogus. There's no
unique information that it conveys and so we can just calculate the number
of sectors from the reported current CHS values.
While we're at it, clean up this function to use named constants for the
identify word values.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Wed, 4 Mar 2009 06:59:30 +0000 (15:59 +0900)]
libata: make sure port is thawed when skipping resets
When SCR access is available and the link is offline, softreset is
skipped as it only wastes time and some controllers don't respond very
well. However, the skip path forgot to thaw the port, which not only
blocks further event notification from the port but also causes
repeated EH invocations on the same event on drivers which rely on
->thaw() to clear events if the IRQ is shared with another device or
port.
This problem has always been there but is uncovered by recent sata_nv
nf2/3 change which dropped hardreset support while maintaining SCR
access. nf2/3 doesn't clear hotplug event mask from the interrupt
handler but relies on ->thaw() to clear them. When the hardreset was
there, the reset action was never skipped and the port was always
thawed but, with the hardreset gone, ->prereset() determines that
there's no need for softreset and both ->softreset() and ->thaw() are
skipped. This leads to stuck hotplug event in the IRQ status register
triggering hotplug event whenever IRQ is delieverd on the same IRQ.
As the controller shares the same IRQ for both ports, this happens on
every IO if one port is occpupied and the other isn't.
This patch fixes the problem by making sure that the port is thawed on
reset-skip path.
bko#11615 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Robert Hancock <hancockrwd@gmail.com> Reported-by: Dan Andresan <danyer@gmail.com> Reported-by: Arne Woerner <arne_woerner@yahoo.com> Reported-by: Stefan Lippers-Hollmann <s.L-H@gmx.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / linux-2.6-omap-h63xx.git / log