gayle: release resources on ide_host_add() failure
"gayle: reserve memory resources at once" patch temporary removed
freeing of resources on failure (to ease convertion to ide_host_add()
interface). This patch fixes it.
Sergei Shtylyov [Thu, 24 Jul 2008 20:53:34 +0000 (22:53 +0200)]
palm_bk3710: add UltraDMA/100 support
This controller supports UltraDMA up to mode 5 but it should be clocked with
at least twice the data strobe frequency, so enable mode 5 for 100+ MHz IDECLK.
While at it, start passing the correct device to clk_get() -- it worked anyway
but WTF? :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Harvey Harrison [Thu, 24 Jul 2008 20:53:33 +0000 (22:53 +0200)]
ide: ide-tape.c sparse annotations and unaligned access removal
If this is actually unaligned the access of speed/max_speed above
is already broken and needs a get_unaligned. Otherwise it is
aligned and they can be removed.
ide: prefix messages from IDE PCI host drivers by driver name
Prefix messages from IDE PCI host drivers by driver name instead of marketed
chipset name (it is still possible to exactly identify the particular chipset
basing on driver messages).
As a bonus this provides nice code savings for some drivers:
* Now that ide_hwif_t instances are allocated dynamically
the difference between MAX_HWIFS == 2 and MAX_HWIFS == 10
is ~100 bytes (x86-32) so use MAX_HWIFS == 10 on all archs
except these ones that use MAX_HWIFS == 1.
* Define MAX_HWIFS in <linux/ide.h> instead of <asm/ide.h>.
[ Please note that avr32/cris/v850 have no <asm/ide.h>
and alpha/ia64/sh always define CONFIG_IDE_MAX_HWIFS. ]
Move ide_probe_legacy() call to ide_generic_init() so it fails
early if necessary and returns the proper error value (nowadays
ide_default_io_base() is used only by ide-generic).
Merge branch 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: hrtick_enabled() should use cpu_active()
sched, x86: clean up hrtick implementation
sched: fix build error, provide partition_sched_domains() unconditionally
sched: fix warning in inc_rt_tasks() to not declare variable 'rq' if it's not needed
cpu hotplug: Make cpu_active_map synchronization dependency clear
cpu hotplug, sched: Introduce cpu_active_map and redo sched domain managment (take 2)
sched: rework of "prioritize non-migratable tasks over migratable ones"
sched: reduce stack size in isolated_cpu_setup()
Revert parts of "ftrace: do not trace scheduler functions"
Fixed up conflicts in include/asm-x86/thread_info.h (due to the
TIF_SINGLESTEP unification vs TIF_HRTICK_RESCHED removal) and
kernel/sched_fair.c (due to cpu_active_map vs for_each_cpu_mask_nr()
introduction).
Merge branch 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
Merge branch 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix invalid proc_handler for softlockup_panic
softlockup: fix watchdog task wakeup frequency
softlockup: fix watchdog task wakeup frequency
softlockup: show irqtrace
softlockup: print a module list on being stuck
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
softlockup: fix false positives on nohz if CPU is 100% idle for more than 60 seconds
softlockup: fix softlockup_thresh fix
softlockup: fix softlockup_thresh unaligned access and disable detection at runtime
softlockup: allow panic on lockup
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
Roland McGrath [Tue, 24 Jun 2008 11:16:52 +0000 (04:16 -0700)]
i386 syscall audit fast-path
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Tue, 24 Jun 2008 08:13:31 +0000 (01:13 -0700)]
x86_64 ia32 syscall audit fast-path
This adds fast paths for 32-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
These paths does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Mon, 23 Jun 2008 22:37:04 +0000 (15:37 -0700)]
x86_64 syscall audit fast-path
This adds a fast path for 64-bit syscall entry and exit when
TIF_SYSCALL_AUDIT is set, but no other kind of syscall tracing.
This path does not need to save and restore all registers as
the general case of tracing does. Avoiding the iret return path
when syscall audit is enabled helps performance a lot.
Roland McGrath [Tue, 24 Jun 2008 03:41:12 +0000 (20:41 -0700)]
x86_64: remove bogus optimization in sysret_signal
This short-circuit path in sysret_signal looks wrong to me.
AFAICT, in practice the branch is never taken--and if it were,
it would go wrong. To wit, try loading a module whose init
function does set_thread_flag(TIF_IRET), and see insmod crash
(presumably with a wrong user stack pointer).
This is because the FIXUP_TOP_OF_STACK work hasn't been done yet
when we jump around the call to ptregscall_common and get to
int_with_check--where it expects the user RSP,SS,CS and EFLAGS to
have been stored by FIXUP_TOP_OF_STACK.
I don't think it's normally possible to get to sysret_signal with no
_TIF_DO_NOTIFY_MASK bits set anyway, so these two instructions are
already superfluous. If it ever did happen, it is harmless to call
do_notify_resume with nothing for it to do.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: highmem capable PIO routines
sg: reimplement sg mapping iterator
mmc_test: print message when attaching to card
mmc: Remove Russell as primecell mci maintainer
mmc_block: bounce buffer highmem support
sdhci: fix bad warning from commit c8b3e02
sdhci: add warnings for bad buffers in ADMA path
mmc_test: test oversized sg lists
mmc_test: highmem tests
s3cmci: ensure host stopped on machine shutdown
au1xmmc: suspend/resume implementation
s3cmci: fixes for section mismatch warnings
pxamci: trivial fix of DMA alignment register bit clearing
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (24 commits)
I/OAT: I/OAT version 3.0 support
I/OAT: tcp_dma_copybreak default value dependent on I/OAT version
I/OAT: Add watchdog/reset functionality to ioatdma
iop_adma: cleanup iop_chan_xor_slot_count
iop_adma: document how to calculate the minimum descriptor pool size
iop_adma: directly reclaim descriptors on allocation failure
async_tx: make async_tx_test_ack a boolean routine
async_tx: remove depend_tx from async_tx_sync_epilog
async_tx: export async_tx_quiesce
async_tx: fix handling of the "out of descriptor" condition in async_xor
async_tx: ensure the xor destination buffer remains dma-mapped
async_tx: list_for_each_entry_rcu() cleanup
dmaengine: Driver for the Synopsys DesignWare DMA controller
dmaengine: Add slave DMA interface
dmaengine: add DMA_COMPL_SKIP_{SRC,DEST}_UNMAP flags to control dma unmap
dmaengine: Add dma_client parameter to device_alloc_chan_resources
dmatest: Simple DMA memcpy test client
dmaengine: DMA engine driver for Marvell XOR engine
iop-adma: fix platform driver hotplug/coldplug
dmaengine: track the number of clients using a channel
...
Fixed up conflict in drivers/dca/dca-sysfs.c manually
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (60 commits)
ide: small whitespace fixes
ide: ide-cd_ioctl.c fix sparse integer as NULL pointer warnings
ide: ide-cd.c fix sparse endianness warnings
ide-cd: convert to using the new atapi_flags
ide: remove unused PC_FLAG_DRQ_INTERRUPT
ide-scsi: convert to using the new atapi_flags
ide-tape: convert to using the new atapi_flags
ide-floppy: convert to using the new atapi_flags (take 2)
ide: add per-device flags
ide: use rq->cmd instead of pc->c in atapi common code
ide-scsi: pass packet command in rq->cmd
ide-tape: pass packet command in rq->cmd
ide-tape: make room for packet command ids in rq->cmd
ide-floppy: pass packet command in rq->cmd
ide: remove pc->callback member from ide_atapi_pc
ide-scsi: use drive->pc_callback instead of pc->callback
ide-tape: use drive->pc_callback instead of pc->callback
ide-floppy: use drive->pc_callback instead of pc->callback
ide: push pc callback pointer into the ide_drive_t structure
drivers/ide/ide-tape.c: remove double kfree
...
Harvey Harrison [Wed, 23 Jul 2008 17:56:02 +0000 (19:56 +0200)]
ide: ide-cd_ioctl.c fix sparse integer as NULL pointer warnings
The function ide_cd_queue_pc should be checked as the bufflen arg is
dereferenced and lots of callers are passing in NULL.
drivers/ide/ide-cd_ioctl.c:124:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:149:47: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:231:46: warning: Using plain integer as NULL pointer
drivers/ide/ide-cd_ioctl.c:374:46: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: Borislav Petkov <petkovbb@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make a redundant copy of the packet command bits into rq->cmd.
Later, after all drivers have been converted, it'll be
switched to use that in the common code instead of pc->c.
There should be no functionality change resulting from this patch.
Make a redundant copy of the packet command bits into rq->cmd. Later, after
all drivers have been converted, it'll be switched to use that in the
common code instead of pc->c. While at it, simplify ide_tape_create_rw_cmd.
There should be no functionality change resulting from this patch.
Make a redundant copy of the packet command bits into rq->cmd.
Later, after all drivers have been converted, it'll be
switched to use that in the common code instead of pc->c.
There should be no functionality change resulting from this patch.
ide-tape: use drive->pc_callback instead of pc->callback
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
ide-floppy: use drive->pc_callback instead of pc->callback
It is important that drive->pc_callback is set prior to enabling IRQs on the
device since this is called from the IRQ handler. Otherwise it hurts as I learnt
the hard way from the several "Kernel panic - not synching: Fatal exception in
interrupt" during the weekend :).
The if-else block in the IRQ handler is only temporary so that bisect searches
don't break and it'll be removed after converting the remainder of the drivers.
There should be no functionality change resulting from this patch.
projects / linux-2.6-omap-h63xx.git / log