x86 ACPI: Blacklist two HP machines with buggy BIOSes
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 4 Oct 2008 19:15:13 +0000 (12:15 -0700)]
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: check broadcast tick device not the clock events device
Linus Torvalds [Sat, 4 Oct 2008 19:14:46 +0000 (12:14 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: correct segfault in generation of 32-bit reloc kernel
Thomas Gleixner [Sat, 4 Oct 2008 08:51:07 +0000 (10:51 +0200)]
clockevents: check broadcast tick device not the clock events device
Impact: jiffies increment too fast.
Hugh Dickins noted that with NOHZ=n and HIGHRES=n jiffies get
incremented too fast. The reason is a wrong check in the broadcast
enter/exit code, which keeps the local apic timer in periodic mode
when the switch happens.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 4 Oct 2008 01:22:36 +0000 (18:22 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
selinux: Fix an uninitialized variable BUG/panic in selinux_secattr_to_sid()
ACPI: Make /proc/acpi/wakeup interface handle PCI devices (again)
Make the ACPI /proc/acpi/wakeup interface set the appropriate wake-up bits
of physical devices corresponding to the ACPI devices and make those bits
be set initially for devices that are enabled to wake up by default. This
is needed to restore the 2.6.26 and earlier behavior for the PCI devices
that were previously handled correctly with the help of the
/proc/acpi/wakeup interface.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sven Wegener [Fri, 3 Oct 2008 22:23:48 +0000 (15:23 -0700)]
leds-pca955x: add proper error handling and fix bogus memory handling
Check the return value of led_classdev_register and unregister all
registered devices, if registering one device fails. Also the dynamic
memory handling is totally bogus. You can't allocate multiple chunks via
kzalloc() and expect them to be in order later. I wonder how this ever
worked.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Nate Case <ncase@xes-inc.com> Tested-by: Nate Case <ncase@xes-inc.com> Acked-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sven Wegener [Fri, 3 Oct 2008 22:23:47 +0000 (15:23 -0700)]
leds-fsg: change order of initialization and deinitialization
On initialization, we first do the ioremap and then register the led devices.
On deinitialization, we do it in reverse order. This prevents someone calling
into the brightness_set functions with an invalid latch_address.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Rod Whitby <rod@whitby.id.au> Acked-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tasklet checks RAW.BLOCK twice, and does not check RAW.XFER. This is
obviously wrong, and could theoretically cause the driver to hang.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Kerrisk [Fri, 3 Oct 2008 22:23:45 +0000 (15:23 -0700)]
Documentation/HOWTO: info about interface changes should CC linux-api@vger
The "Documentation" section of this file mentions that when an interface
change is made, I should be CCed with info about the change (so that
man-pages can document it). Additionally request that this info be CCed
to the new linux-api@vger.kernel.org list.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Fri, 3 Oct 2008 22:23:42 +0000 (15:23 -0700)]
cpusets: remove pj from cpuset maintainers
Remove myself from the kernel MAINTAINERS file for cpusets. I am leaving
SGI and probably will not be active in Linux kernel work. I can be
reached at <pj@usa.net>. Contact Derek Fults <dfults@sgi.com> for future
SGI+cpuset related issues. I'm off to the next chapter of this good life.
Signed-off-by: Paul Jackson <pj@sgi.com> Cc: Paul Menage <menage@google.com> Cc: Derek Fults <dfults@sgi.com> Cc: John Hesterberg <jh@sgi.com> Cc: Paul Jackson <pj@usa.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
include/linux/stacktrace.h:13: warning:
'struct task_struct' declared inside parameter list
(This might be a hard error on sparc64, which uses this header and has
-Werror)
Reported-by: "Randy.Dunlap" <rdunlap@xenotime.net> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Krzysztof Helt [Fri, 3 Oct 2008 22:23:38 +0000 (15:23 -0700)]
fbdev: fix recursive notifier and locking when fbdev console is blanked
Fix infinite recursive notifier in the fbdev layer. This causes recursive
locking. Dmitry Baryshkov found the problem and confirmed that the patch
fixes the bug.
After doing
# echo 1 > /sys/class/graphics/fb0/blank
I got the following in my kernel log:
=============================================
[ INFO: possible recursive locking detected ] 2.6.27-rc6-00086-gda63874-dirty #97
---------------------------------------------
echo/1564 is trying to acquire lock:
((fb_notifier_list).rwsem){..--}, at: [<c005a384>] __blocking_notifier_call_chain+0x38/0x6c
but task is already holding lock:
((fb_notifier_list).rwsem){..--}, at: [<c005a384>] __blocking_notifier_call_chain+0x38/0x6c
other info that might help us debug this:
2 locks held by echo/1564:
#0: (&buffer->mutex){--..}, at: [<c00ddde0>] sysfs_write_file+0x30/0x80
#1: ((fb_notifier_list).rwsem){..--}, at: [<c005a384>] __blocking_notifier_call_chain+0x38/0x6c
Marcin Slusarz [Fri, 3 Oct 2008 22:23:36 +0000 (15:23 -0700)]
rtc: fix kernel panic on second use of SIGIO nofitication
When userspace uses SIGIO notification and forgets to disable it before
closing file descriptor, rtc->async_queue contains stale pointer to struct
file. When user space enables again SIGIO notification in different
process, kernel dereferences this (poisoned) pointer and crashes.
So disable SIGIO notification on close.
Kernel panic:
(second run of qemu (requires echo 1024 > /sys/class/rtc/rtc0/max_user_freq))
Paul Moore [Fri, 3 Oct 2008 14:51:15 +0000 (10:51 -0400)]
selinux: Fix an uninitialized variable BUG/panic in selinux_secattr_to_sid()
At some point during the 2.6.27 development cycle two new fields were added
to the SELinux context structure, a string pointer and a length field. The
code in selinux_secattr_to_sid() was not modified and as a result these two
fields were left uninitialized which could result in erratic behavior,
including kernel panics, when NetLabel is used. This patch fixes the
problem by fully initializing the context in selinux_secattr_to_sid() before
use and reducing the level of direct context manipulation done to help
prevent future problems.
Please apply this to the 2.6.27-rcX release stream.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
H. Peter Anvin [Fri, 3 Oct 2008 20:00:56 +0000 (13:00 -0700)]
x86 setup: correct segfault in generation of 32-bit reloc kernel
Impact: segfault on build of a 32-bit relocatable kernel
When converting arch/x86/boot/compressed/relocs.c to support unlimited
sections, the computation of sym_strtab in walk_relocs() was done
incorrectly. This causes a segfault for some people when building the
relocatable 32-bit kernel.
Linus Torvalds [Fri, 3 Oct 2008 20:38:07 +0000 (13:38 -0700)]
Fix init/main.c to use regular printk with '%pF' for initcall fn
.. small detail, but the silly e1000e initcall warning debugging caused
me to look at this code. Rather than gouge my eyes out with a spoon, I
just fixed it.
Heiko Carstens [Fri, 3 Oct 2008 19:54:59 +0000 (21:54 +0200)]
[S390] nohz: Fix __udelay.
This fixes a regression that came with 934b2857cc576ae53c92a66e63fce7ddcfa74691
("[S390] nohz/sclp: disable timer on synchronous waits.").
If udelay() gets called from a disabled context it sets the clock comparator
to a value where it expects the next interrupt. When the interrupt happens
the clock comparator gets not reset and therefore the interrupt condition
doesn't get cleared. The result is an endless timer interrupt loop.
In addition this patch fixes also the following:
rcutorture reveals that our __udelay implementation is still buggy,
since it might schedule tasklets, but prevents their execution:
To fix this we make sure that only the clock comparator interrupt
is enabled when the enabled wait psw is loaded.
Also no code gets called anymore which might schedule tasklets.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop. The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 1 Oct 2008 20:52:41 +0000 (21:52 +0100)]
[MIPS] Build fix: Fix irq flags type
Though from a hardware perspective it would be sensible to use only a
32-bit unsigned int type Linux defines interrupt flags to be stored in
an unsigned long and nothing else.
Linus Torvalds [Fri, 3 Oct 2008 16:18:17 +0000 (09:18 -0700)]
e1000e: Fix incorrect debug warning
Doing 'WARN_ON(preempt_count())' was horribly horribly wrong, and would
cause tons of warnings at bootup if PREEMPT was enabled because the
initcalls currently run with the kernel lock, which increments the
preempt count.
At the same time, the warning was also insufficient, since it didn't
check that interrupts were enabled.
The proper debug function to use for something that can sleep and wants
a warning if it's called in the wrong context is 'might_sleep()'.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 3 Oct 2008 01:52:51 +0000 (18:52 -0700)]
Check mapped ranges on sysfs resource files
This is loosely based on a patch by Jesse Barnes to check the user-space
PCI mappings though the sysfs interfaces. Quoting Jesse's original
explanation:
It's fairly common for applications to map PCI resources through sysfs.
However, with the current implementation, it's possible for an application
to map far more than the range corresponding to the resourceN file it
opened. This patch plugs that hole by checking the range at mmap time,
similar to what is done on platforms like sparc64 in their lower level
PCI remapping routines.
It was initially put together to help debug the e1000e NVRAM corruption
problem, since we initially thought an X driver might be walking past the
end of one of its mappings and clobbering the NVRAM. It now looks like
that's not the case, but doing the check is still important for obvious
reasons.
and this version of the patch differs in that it uses a helper function
to clarify the code, and does all the checks in pages (instead of bytes)
in order to avoid overflows when doing "<< PAGE_SHIFT" etc.
thanks to tglx, we're finding some interesting reentrancy issues.
this patch removes the phy read from inside a spinlock, paving
the way for removing the spinlock completely. The phy read was
only feeding a statistic that wasn't used.
e1000e was apparently calling two functions that attempted to reserve
the SWFLAG bit for exclusive (to hardware and firmware) access to
the PHY and NVM (aka eeprom). These accesses could possibly call
msleep to wait for the resource which is not allowed from interrupt
context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
in the process of debugging things, noticed that the swflag is not reset
by the driver after reset, and the swflag is probably not reset unless
management firmware clears it after 100ms.
Andy Whitcroft [Thu, 2 Oct 2008 21:50:18 +0000 (14:50 -0700)]
mm: handle initialising compound pages at orders greater than MAX_ORDER
When we initialise a compound page we initialise the page flags and head
page pointer for all base pages spanned by that page. When we initialise
a gigantic page (a page of order greater than or equal to MAX_ORDER) we
have to initialise more than MAX_ORDER_NR_PAGES pages. Currently we
assume that all elements of the mem_map in this page are contigious in
memory. However this is only guarenteed out to MAX_ORDER_NR_PAGES pages,
and with SPARSEMEM enabled they will not be contigious. This leads us to
walk off the end of the first section and scribble on everything which
follows, BAD.
When we reach a MAX_ORDER_NR_PAGES boundary we much locate the next
section of the mem_map. As gigantic pages can only be maximally aligned
we know this will occur at exact multiple of MAX_ORDER_NR_PAGES pages from
the start of the page.
This is a bug fix for the gigantic page support in hugetlbfs.
Credit to Mel Gorman for spotting the issue.
Signed-off-by: Andy Whitcroft <apw@shadowen.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Jon Tollefson <kniht@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Thu, 2 Oct 2008 21:50:16 +0000 (14:50 -0700)]
mm: tiny-shmem nommu fix
The previous patch db203d53d474aa068984e409d807628f5841da1b ("mm:
tiny-shmem fix lock ordering: mmap_sem vs i_mutex") to fix the lock
ordering in tiny-shmem breaks shared anonymous and IPC memory on NOMMU
architectures because it was using the expanding truncate to signal ramfs
to allocate a physically contiguous RAM backing the inode (otherwise it is
unusable for "memory mapping" it to userspace).
However do_truncate is what caused the lock ordering error, due to it
taking i_mutex. In this case, we can actually just call ramfs directly to
allocate memory for the mapping, rather than go via truncate.
Acked-by: David Howells <dhowells@redhat.com> Acked-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerald Schaefer [Thu, 2 Oct 2008 21:50:16 +0000 (14:50 -0700)]
memory hotplug: missing zone->lock in test_pages_isolated()
__test_page_isolated_in_pageblock() in mm/page_isolation.c has a comment
saying that the caller must hold zone->lock. But the only caller of that
function, test_pages_isolated(), does not hold zone->lock and the lock is
also not acquired anywhere before. This patch adds the missing zone->lock
to test_pages_isolated().
We reproducibly run into BUG_ON(!PageBuddy(page)) in __offline_isolated_pages()
during memory hotplug stress test, see trace below. This patch fixes that
problem, it would be good if we could have it in 2.6.27.
David Winn [Thu, 2 Oct 2008 21:50:11 +0000 (14:50 -0700)]
fbcon: fix monochrome color value calculation
Commit 22af89aa0c0b4012a7431114a340efd3665a7617 ("fbcon: replace mono_col
macro with static inline") changed the order of operations for computing
monochrome color values. This generates 0xffff000f instead of 0x0000000f
for a 4 bit monochrome color, leading to image corruption if it is passed
to cfb_imageblit or other similar functions. Fix it up.
Cc: Harvey Harrison <harvey.harrison@gmail.com> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: <stable@kernel.org> [2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Oct 2008 14:54:32 +0000 (07:54 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: snd-powermac: HP detection for 1st iMac G3 SL
ALSA: snd-powermac: mixers for PowerMac G4 AGP
ASoC: Set correct name for WM8753 rec mixer output
Rob Sims [Wed, 1 Oct 2008 19:47:31 +0000 (21:47 +0200)]
ASoC: Set correct name for WM8753 rec mixer output
Rob Sims wrote:
"I can't seem to turn on register 0x17, bit 3 in the sound chip, except
by codec_reg_write; the mixer lacks direct or indirect control. It
seems there are two names for the output of the rec mixer:
Capture ST Mixer
Playback Mixer
Would the following do the trick?"
I confirm that this solves the audio problems I was having.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kumar Gala [Thu, 2 Oct 2008 05:58:49 +0000 (00:58 -0500)]
powerpc: Fix boot hang regression on MPC8544DS
Commit 00c5372d37a78990c1530184a9c792ee60a30067 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bruce Allan [Thu, 2 Oct 2008 00:18:35 +0000 (17:18 -0700)]
e1000e: write protect ICHx NVM to prevent malicious write/erase
Set the hardware to ignore all write/erase cycles to the GbE region in
the ICHx NVM. This feature can be disabled by the WriteProtectNVM module
parameter (enabled by default) only after a hardware reset, but
the machine must be power cycled before trying to enable writes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: arjan@linux.intel.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CC drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Wed, 1 Oct 2008 12:47:06 +0000 (13:47 +0100)]
MN10300: Fix IRQ handling
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm mpath: add missing path switching locking
dm: cope with access beyond end of device in dm_merge_bvec
dm: always allow one page in dm_merge_bvec
Moving the path activation to workqueue along with scsi_dh patches introduced
a race. It is due to the fact that the current_pgpath (in the multipath data
structure) can be modified if changes happen in any of the paths leading to
the lun. If the changes lead to current_pgpath being set to NULL, then it
leads to the invalid access which results in the panic below.
This patch fixes that by storing the pgpath to activate in the multipath data
structure and properly protecting it.
Note that if activate_path is called twice in succession with different pgpath,
with the second one being called before the first one is done, then activate
path will be called twice for the second pgpath, which is fine.
Mikulas Patocka [Wed, 1 Oct 2008 13:39:24 +0000 (14:39 +0100)]
dm: cope with access beyond end of device in dm_merge_bvec
If for any reason dm_merge_bvec() is given an offset beyond the end of the
device, avoid an oops and always allow one page to be added to an empty bio.
We'll reject the I/O later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Wed, 1 Oct 2008 13:39:17 +0000 (14:39 +0100)]
dm: always allow one page in dm_merge_bvec
Some callers assume they can always add at least one page to an empty bio,
so dm_merge_bvec should not return 0 in this case: we'll reject the I/O
later after the bio is submitted.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
ip6_dst_blackhole_ops.kmem_cachep is not expected to be NULL (i.e. to
be initialized) when dst_alloc() is called from ip6_dst_blackhole().
Otherwise, it results in the following (xfrm_larval_drop is now set to
1 by default):
Signed-off-by: Arnaud Ebalard <arno@natisbad.org> Acked-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56ca09a467fbbe5229bc68627f7445be
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com> Cc: Glauber de Oliveira Costa <gcosta@redhat.com> Cc: stable@kernel.org Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56ca09a467fbbe5229bc68627f7445be
Signed-off-by: Zachary Amsden <zach@vmware.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Glauber de Oliveira Costa <gcosta@redhat.com> Cc: <stable@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix failure to shutdown with CPU hotplug
powerpc: Fix PCI in Holly device tree
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimer: prevent migration of per CPU hrtimers
hrtimer: mark migration state
hrtimer: fix migration of CB_IRQSAFE_NO_SOFTIRQ hrtimers
hrtimer: migrate pending list on cpu offline
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
sctp: Fix kernel panic while process protocol violation parameter
Since call to function sctp_sf_abort_violation() need paramter 'arg' with
'struct sctp_chunk' type, it will read the chunk type and chunk length from
the chunk_hdr member of chunk. But call to sctp_sf_violation_paramlen()
always with 'struct sctp_paramhdr' type's parameter, it will be passed to
sctp_sf_abort_violation(). This may cause kernel panic.
This patch fixed this problem. This patch also fix two place which called
sctp_sf_violation_paramlen() with wrong paramter type.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dell Inspiron 1525 seems to have a buggy BIOS setup and screws up
the recent codec parser, as reported by Oleksandr Natalenko:
http://lkml.org/lkml/2008/9/12/203
This patch adds the working model, dell-3stack, statically.
Jean Delvare [Tue, 30 Sep 2008 09:40:37 +0000 (11:40 +0200)]
ALSA: ASoC: Fix cs4270 error path
The error path in cs4270_probe/cs4270_remove is pretty broken:
* If cs4270_probe fails, codec is leaked.
* If snd_soc_register_card fails, cs4270_i2c_driver stays registered.
* If I2C support is enabled but no I2C device is found, i2c_del_driver
is never called (neither in cs4270_probe nor in cs4270_remove.
Fix all 3 problems by implementing a clean error path in cs4270_probe
and jumping to its labels as needed.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
fb65a7c091529bfffb1262515252c0d0f6241c5c ("iucv: Fix bad merging.") fixed
a merge error, but in a wrong way. We now end up with the bug below.
This patch corrects the mismerge like it was intended.
Johannes Berg [Wed, 24 Sep 2008 22:56:25 +0000 (22:56 +0000)]
powerpc: Fix failure to shutdown with CPU hotplug
I tracked down the shutdown regression to CPUs not dying
when being shut down during power-off. This turns out to
be due to the system_state being SYSTEM_POWER_OFF, which
this code doesn't take as a valid state for shutting off
CPUs in.
This has never made sense to me, but when I added hotplug
code to implement hibernate I only "made it work" and did
not question the need to check the system_state. Thomas
Gleixner helped me dig, but the only thing we found is
that it was added with the original commit that added CPU
hotplug support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Gibson [Wed, 24 Sep 2008 16:39:04 +0000 (16:39 +0000)]
powerpc: Fix PCI in Holly device tree
The PCI bridge on the Holly board is incorrectly represented in the
device tree. The current device tree node for the PCI bridge sits
under the tsi-bridge node. That's not obviously wrong, but the PCI
bridge translates some PCI spaces into CPU address ranges which were
not translated by the "ranges" property in tsi-bridge node.
We used to get away with this problem because the PCI bridge discovery
code was also buggy, assuming incorrectly that PCI host bridge nodes
were always directly under the root bus and treating the translated
addresses as raw CPU addresses, rather than parent bus addresses.
This has since been fixed, thus breaking Holly.
This could be fixed by adding extra translations to the tsi-bridge
node, but this patch instead moves the Holly PCI bridge out of the
tsi-bridge node to the root bus. This makes the tsi-bridge node
represent only the built-in IO devices in the bridge, with a
more-or-less contiguous address range. This is the same convention
used on Freescale SoC chips, where the "soc" node represents only the
IMMR region, and the PCI and other bus bridges are separate nodes
under the root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tony Luck [Mon, 29 Sep 2008 23:39:19 +0000 (16:39 -0700)]
[IA64] Put the space for cpu0 per-cpu area into .data section
Initial fix for making sure that we can access percpu variables
in all C code (commit: 10617bbe84628eb18ab5f723d3ba35005adde143)
inadvertantly allocated the memory in the "percpu" section of
the vmlinux ELF executable. This confused kexec/dump.
There's a race between mm->owner assignment and swapoff, more easily
seen when task slab poisoning is turned on. The condition occurs when
try_to_unuse() runs in parallel with an exiting task. A similar race
can occur with callers of get_task_mm(), such as /proc/<pid>/<mmstats>
or ptrace or page migration.
CPU0 CPU1
try_to_unuse
looks at mm = task0->mm
increments mm->mm_users
task 0 exits
mm->owner needs to be updated, but no
new owner is found (mm_users > 1, but
no other task has task->mm = task0->mm)
mm_update_next_owner() leaves
mmput(mm) decrements mm->mm_users
task0 freed
dereferencing mm->owner fails
The fix is to notify the subsystem via mm_owner_changed callback(),
if no new owner is found, by specifying the new task as NULL.
Jiri Slaby:
mm->owner was set to NULL prior to calling cgroup_mm_owner_callbacks(), but
must be set after that, so as not to pass NULL as old owner causing oops.
Daisuke Nishimura:
mm_update_next_owner() may set mm->owner to NULL, but mem_cgroup_from_task()
and its callers need to take account of this situation to avoid oops.
Hugh Dickins:
Lockdep warning and hang below exec_mmap() when testing these patches.
exit_mm() up_reads mmap_sem before calling mm_update_next_owner(),
so exec_mmap() now needs to do the same. And with that repositioning,
there's now no point in mm_need_new_owner() allowing for NULL mm.
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
cdrom: update ioctl documentation
ide: note that IDE generic may prevent other drivers from attaching
ide-tape: fix vendor strings
Swarm: Fix crash due to missing initialization
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdboc,tty: Fix tty polling search to use name correctly
kgdb, x86_64: fix PS CS SS registers in gdb serial
kgdb, x86_64: gdb serial has BX and DX reversed
kgdb, x86, arm, mips, powerpc: ignore user space single stepping
kgdb: could not write to the last of valid memory with kgdb
Thomas Gleixner [Mon, 29 Sep 2008 13:47:42 +0000 (15:47 +0200)]
hrtimer: prevent migration of per CPU hrtimers
Impact: per CPU hrtimers can be migrated from a dead CPU
The hrtimer code has no knowledge about per CPU timers, but we need to
prevent the migration of such timers and warn when such a timer is
active at migration time.
Explicitely mark the timers as per CPU and use a more understandable
mode descriptor for the interrupts safe unlocked callback mode, which
is used by hrtimer_sleeper and the scheduler code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Mon, 29 Sep 2008 13:44:46 +0000 (15:44 +0200)]
hrtimer: mark migration state
Impact: during migration active hrtimers can be seen as inactive
The migration code removes the hrtimers from the queues of the dead
CPU and sets the state temporary to INACTIVE. The enqueue code sets it
to ACTIVE/PENDING again.
Prevent that the wrong state can be seen by using a separate migration
state bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
changed the hrtimer sleeper callback mode to CB_IRQSAFE_NO_SOFTIRQ due
to locking problems. A result of this change is that when enqueue is
called for an already expired hrtimer the callback function is not
longer called directly from the enqueue code. The normal callers have
been fixed in the code, but the migration code which moves hrtimers
from a dead CPU to a live CPU was not made aware of this.
This can be fixed by checking the timer state after the call to
enqueue in the migration code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Fix another cs4270 error path
ALSA: make the CS4270 driver a new-style I2C driver
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qlogicpti: fix sg list traversal error in continuation entries
[SCSI] Fix hang with split requests
[SCSI] qla2xxx: Defer enablement of RISC interrupts until ISP initialization completes.
Commit f072181e6403b0fe2e2aa800a005497b748fd284 ("kconfig: drop the
""trying to assign nonexistent symbol" warning") simply dropped the
warnings, but it does a little more than that, it also marks the current
.config as needed saving, so add this back.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent changes to oldconfig have mixed up the silentoldconfig handling,
so this fixes that by clearly separating that special mode, e.g.
KCONFIG_NOSILENTUPDATE is only relevant here, the .config is written as
needed.
This will also properly close Bug 11230.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The VFS interface for the 'd_compare()' is a bit special (read: 'odd'),
because it really just essentially replaces a memcmp(). The filesystem
is supposed to just compare the two names with whatever case-independent
or other function.
And when I say 'is supposed to', I obviously mean that 'procfs does odd
things, and actually looks at the dentry that we don't even pass down,
rather than just the name'. Which results in problems, because we
actually call d_compare before we have even verified that the dentry is
still hashed at all.
And that causes a problm since the inode that procfs looks at may have
been free'd and the d_inode pointer is NULL. procfs just assumes that
all dentries are positive, since procfs itself never generates a
negative one. But memory pressure will still result in the dentry
getting torn down, and as it is removed by RCU, it still remains visible
on some lists - and to d_compare.
If the filesystem just did a name comparison, we wouldn't care. And we
could just fix procfs to know about negative dentries too. But rather
than have the low-level filesystems know about internal VFS details,
just move the check for a unhashed dentry up a bit, so that we will only
call d_compare on dentries that are still active.
The actual oops this caused didn't look like a NULL pointer dereference
because procfs did a 'container_of(inode, struct proc_inode, vfs_inode)'
to get at its internal proc_inode information from the inode pointer,
and accessed a field below the inode. So the oops would look something
like
projects / linux-2.6-omap-h63xx.git / log