x86: let 64 bit to use 32 bit calibrate_apic_clock

Use the 32-bit APIC calibration code - it's more mature.

Signed-of-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: rename apic_32.c and apic_64.c to apic.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic copy apic_64.c to apic_32.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic copy calibrate_APIC_clock to each other in apic_32/64.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic unify smp_spurious/error_interrupt

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: merge header files in apic_xx.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: copy detect_init_APIC to the other

Signed-off-by: Yinghai Lu <yhlu.kernel@mgail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: merge APIC_init_uniprocessor

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make apic_32/64.c more like

except x2apic, detec_init_APIC, and calibrating_APIC_clock

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add hard_smp_prossor_id with MACRO in io_apic_xx.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: use HAVE_X2APIC in apic_64.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic_xx.c order variables

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic - unify smp_apic_timer_interrupt

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic_32.c should use __cpuinit section

All callers are __init or __cpuinit so there is no need
to hold this code without CPU_HOTPLUG being set.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic - unify setup_local_APIC

- remove useless read of APIC_LVR
- wrap with preempt_disable/enable
- check for integrated APIC just in place

v2: fix by Yinghai Lu.
fix lapic_is_integrated using
let 64-bit too have pic_mode

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic_64.c - add sanity check for spurious vector definition

Do not check for SPUTIOUS_APIC_VECTOR definition twice.
Check it once - is what we need.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic - unify setup_apicpmtimer

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic - introduce get_physical_broadcast for 64bit

We don't really use it now on 64bit mode but
could reserve it for future.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: apic_64.c - setup_APIC_timer has to be __cpuinit function

There is no need to hold this code if CPU_HOTPLUG is not
defined.

Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: VMI, initialize IRQ vector

Initialize vector_irq for the vmi used vector, to point to correct irq.

Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: fix probe_nr_irqs for xen

otherwise Xen is _completely_ unusable with 5 or more VCPUs.
(when !CONFIG_HAVE_SPARSE_IRQ).

based on Alex Nixon's patch.

also add +1 offset after redir_entries

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Alex Nixon <alex.nixon@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: fix 32-bit ioapic lockup with sparseirqs

Missed two lines when copying.

Fix panic on one of Ingo's machines that need to adjust ioapic id when
acpi off/ 32bit.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: sparse_irq needs spin_lock in allocations

Suresh Siddha noticed that we should have a spinlock around it.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

sparseirq: fix intr-remap with dyn_array/nr_irqs changes]

In irq_2_iommu_alloc() and set_irte_irq(), irq_to_desc or
irq_2_iommu pointers may not be allocated. So use the routines
which will allocate them if they are not already allocated.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

warning: fix arch x86 kernel io_apic c

fix warning:

  arch/x86/kernel/io_apic.c: In function ‘print_local_APIC’:
  arch/x86/kernel/io_apic.c:1786: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘u64’
  arch/x86/kernel/io_apic.c:1787: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 2 has type ‘u64’

By creating uniform behavior on 32-bit and 64-bit and printing out the ICR
value in two 32-bit words.

Code has changed:

   text    data     bss     dec     hex filename
  22901   19650   17040   59591    e8c7 io_apic.o.before
  22899   19650   17040   59589    e8c5 io_apic.o.after

Due to the 32-bit cast narrowing the printed out value on 64-bit.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

xen: Fix bug `do_IRQ: cannot handle IRQ -1 vector 0x6 cpu 1'

Following commit 9c3f2468d8339866d9ef6a25aae31a8909c6be0d, do_IRQ()
looks up the IRQ number in the per-cpu variable vector_irq.

This commit makes Xen initialise an identity vector_irq map for both X86_32 and X86_64.

Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

dyn_array: split dyn_array functions from init/main.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

xen: fix memory access violation bug when CONFIG_HAVE_SPARSE_IRQ is enabled

When sparse IRQs are enabled, it is not safe to assume an IRQ descriptor
exists for every possible IRQ.  This patch causes init_evtchn_cpu_bindings
to skip initialisation of IRQ descriptors which don't exist.

Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: probe nr_irqs even only mptable is used

for !CONFIG_HAVE_SPARSE_IRQ

fix:

 In file included from arch/x86/kernel/early-quirks.c:18:
 include/asm/io_apic.h: In function 'probe_nr_irqs':
 include/asm/io_apic.h:209: error: 'NR_IRQS' undeclared (first use in this function)
 include/asm/io_apic.h:209: error: (Each undeclared identifier is reported only once
 include/asm/io_apic.h:209: error: for each function it appears in.)

v2: fix by Ingo

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make HAVE_SPARSE_IRQ support selectable

Ingo said sparse_irq is some intrusive. need to make it selectable

to make it simple, remove irq_desc as parameter in some functions.
(ack, eoi, set_affinity).
may need to make member if irq_chip to take irq_desc, or struct irq later.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: print local APIC of APs one by one

instead of print that of all APs at the time

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: remove first_free_entry/pin_map_size

no user now

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: unify ack_apic_edge

use code in 64 to replace
move_native_irq(irq, desc);
in 32 bit

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: unify mask_IO_APIC_irq

use MACRO for 32 bit too

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: irq: interrupt array size should be NR_VECTORS

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

pci: change msi-x vector to 32bit

we are using 28bit pci (bus/dev/fn + 12 bits) as irq number, so the
cache for irq number should be 32 bit too.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

io_apic: make 32 bit have io_apic resource in /proc/iomem

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

rename io_apic_64.c and io_apic_32.c to io_apic.c

The two files are now line by line equal. (sans a printk)

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make io_apic_32.c the same as io_apic_64.c

Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make io_apic_64.c and io_apic_32.c the same

all the same except INTR_REMAPPING related and ioapic io resource.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: remove ioapic_force

no user left.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make 64 handle sis_apic_bug like the 32 bit

do we have 64bit system with sis chipset?

[ mingo@elte.hu: nope, the problem chipset was 32-bit only.
                 The code symmetry is good nevertheless. ]

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make headers files the same in io_apic_xx.c

also make no_timer_check to be global on 64 bit, because vmi_32 is using that.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

sparseirq: fix lockdep

-tip testing found this lockdep splat:

[    0.000000] Initializing CPU#0
[    0.000000] found new irq_desc for irq 0
[    0.000000] INFO: trying to register non-static key.
[    0.000000] the code is fine but needs lockdep annotation.
[    0.000000] turning off the locking correctness validator.
[    0.000000] Pid: 0, comm: swapper Not tainted 2.6.27-rc3-tip-00191-g98ccb89-dirty #1
[    0.000000]  [<c0153c22>] register_lock_class+0x3d2/0x400
[    0.000000]  [<c0104d87>] ? mcount_call+0x5/0xa
[    0.000000]  [<c0154f3a>] __lock_acquire+0x22a/0x5d0
[    0.000000]  [<c0104d87>] ? mcount_call+0x5/0xa
[    0.000000]  [<c0155351>] lock_acquire+0x71/0xa0
[    0.000000]  [<c016d61f>] ? set_irq_chip+0x3f/0x90
[    0.000000]  [<c070f148>] _spin_lock_irqsave+0x58/0x90
[    0.000000]  [<c016d61f>] ? set_irq_chip+0x3f/0x90
[    0.000000]  [<c016d61f>] set_irq_chip+0x3f/0x90
[    0.000000]  [<c016d7e0>] ? handle_level_irq+0x0/0xe0
[    0.000000]  [<c016da1a>] set_irq_chip_and_handler_name+0x1a/0x40
[    0.000000]  [<c0a396c1>] init_ISA_irqs+0x51/0xa0
[    0.000000]  [<c0a4a365>] pre_intr_init_hook+0x25/0x30
[    0.000000]  [<c0a39723>] native_init_IRQ+0x13/0x370
[    0.000000]  [<c015569c>] ? lock_release+0xcc/0x1d0
[    0.000000]  [<c0104d87>] ? mcount_call+0x5/0xa
[    0.000000]  [<c070dc22>] ? __mutex_unlock_slowpath+0x92/0x110
[    0.000000]  [<c070dcad>] ? mutex_unlock+0xd/0x10
[    0.000000]  [<c0135f62>] ? cpu_maps_update_done+0x12/0x20
[    0.000000]  [<c06c6743>] ? register_cpu_notifier+0x23/0x30
[    0.000000]  [<c011e8ae>] init_IRQ+0xe/0x10
[    0.000000]  [<c0a357a5>] start_kernel+0x1c5/0x340
[    0.000000]  [<c0a35280>] ? unknown_bootoption+0x0/0x210
[    0.000000]  [<c0a3506b>] i386_start_kernel+0x6b/0x80
[    0.000000]  =======================
[    0.000000] found new irq_desc for irq 1
[    0.000000] found new irq_desc for irq 2
[    0.000000] found new irq_desc for irq 3

this:

 static void init_one_irq_desc(struct irq_desc *desc)
 {
         memcpy(desc, &irq_desc_init, sizeof(struct irq_desc));
 #ifdef CONFIG_TRACE_IRQFLAGS
         lockdep_set_class(&desc->lock, &irq_desc_lock_class);
 #endif
 }

should be unconditional.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: order variables in io_apic_xx.c

move first_system_vector to apic_64.c.

also add #ifdef CONFIG_INTR_REMAP to prepare 32 bit to use
same file.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: ordering functions in io_apic_64.c

try to make functions have the same order between 32-bit and 64-bit.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: ordering functions in io_apic_32.c

prepare for unification:

try to make functions be of the same order to io_apic_64.c.

v2: add calling setup_msi_irq back to arch_setup_msi_irq

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, io-apic: remove union about dest for log/phy

let user decide the meaning of the bits.

This unifies the 32-bit and 64-bit io-apic code a bit.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add debug info for 32bit sparse_irq

so could figure out bugs where we get an interrupt, but vector_irq is
not initialized yet.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make 32bit support per_cpu vector

so we can merge io_apic_32.c and io_apic_64.c

v2: Use cpu_online_map as target cpus for bigsmp, just like 64-bit is doing.

Also remove some unused TARGET_CPUS macro.

v3: need to check if desc is null in smp_irq_move_cleanup

also migration needs to reset vector too, so copy __target_IO_APIC_irq
from 64bit.

(the duplication will go away once the two files are unified.)

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make 32 bit to use sparse_irq

but actually irq still needs to be less than NR_IRQS, because
interrupt[NR_IRQS] in entry.S.

need to enable per_cpu vector...

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make 32bit to use irq_2_pin in irq_cfg

so it is more like 64 bit.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: make 32bit use irq_cfg_alloc, etc

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add irq_cfg for 32bit

it only contains vector ...

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: remove irqbalance in kernel for 32 bit

This has been deprecated for years, the user space irqbalanced utility
works better with numa, has configurable policies, etc...

Signed-off-by: Yinghai Lu <yhlu.kernel@gmai.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: use 28 bits irq NR for pci msi/msix and ht

also print out irq no in /proc/interrups and /proc/stat in hex, so could
tell bus/dev/func.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: put irq_2_iommu pointer into irq_desc

when CONFIG_HAVE_SPARSE_IRQ
preallocate some irq_2_iommu entries, and use get_one_free_irq_2_iomm to
get new one and link to irq_desc if needed.

else will use dyn_array or static array.

v2: <= nr_irqs fix

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86_64: make /proc/interrupts work with dyn irq_desc

loop with irq_desc list

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86_64: separate irq_cfgx from irq_cfgx_free

so later don't need to compare with -1U

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: separate sparse_irqs from sparse_irqs_free

so later don't need compare with -1U

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86_64: rename irq_desc/irq_desc_alloc

change names:

          irq_desc() ==> irq_desc_alloc
__irq_desc() ==> irq_desc

Also split a few of the uses in lowlevel x86 code.

v2: need to check if desc is null in smp_irq_move_cleanup

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: check with without_new in show_interrupts

so we don't get new one that we don't need it.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

generic: add irq_desc in function in parameter

So we could remove some duplicated calling to irq_desc

v2: make sure irq_desc in  init/main.c is not used without generic_hardirqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: remove >= nr_irqs checking with config_have_sparse_irq

remove irq limit checks - nr_irqs is dynamic and we expand anytime.

v2: fix checking about result irq_cfg_without_new, so could use msi again
v3: use irq_desc_without_new to check irq is valid

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, ioapic: replace loop with nr_irqs with for_each_irq_icfg

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq, fs/proc: replace loop with nr_irqs for proc/stat

Replace another nr_irqs loop to avoid the allocation of all sparse
irq entries - use for_each_irq_desc instead.

v2: make sure arch without GENERIC_HARDIRQS works too

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: replace loop with nr_irqs with for_each_irq_desc

There are a handful of loops that go from 0 to nr_irqs and use
get_irq_desc() on them. These would allocate all the irq_desc
entries, regardless of the need for them.

Use the smarter for_each_irq_desc() iterator that will only iterate
over the present ones.

v2: make sure arch without GENERIC_HARDIRQS work too

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: add irq_desc_without_new

add an irq_desc accessor that will not allocate any sparse entry
but returns failure if there's no entry present.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: move kstat_irqs from kstat to irq_desc

based on Eric's patch ...

together mold it with dyn_array for irq_desc, will allcate kstat_irqs for
nr_irq_desc alltogether if needed. -- at that point nr_cpus is known already.

v2: make sure system without generic_hardirqs works they don't have irq_desc
v3: fix merging
v4: [mingo@elte.hu] fix typo

[ mingo@elte.hu ] irq: build fix

fix:

 arch/x86/xen/spinlock.c: In function 'xen_spin_lock_slow':
 arch/x86/xen/spinlock.c:90: error: 'struct kernel_stat' has no member named 'irqs'

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: put timer_rand_state pointer into irq_desc

irq_timer_state[] is a NR_IRQS sized array that is a side-by array to
the real irq_desc[] array.

Integrate that field into the (now dynamic) irq_desc dynamic array and
save some RAM.

v2: keep the old way to support arch not support irq_desc

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: put irq_2_pin pointer into irq_cfg

preallocate 32 irq_2_pin entries, and use get_one_free_irq_2_pin() to get
one more and link to irq_cfg if needed.

so don't waste one where no irq is enabled.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add irq_cfg in io_apic_64.c

preallocate size is 32, and if it is not enough, irq_cfg will more
via alloc_bootmem() or kzalloc(). (depending on how early we are in
system setup)

v2: fix typo about size of init_one_irq_cfg ... should use sizeof(struct irq_cfg)
v3: according to Eric, change get_irq_cfg() to irq_cfg()
v4: squash add irq_cfg_alloc in

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: sparse irqs, fix IRQ auto-probe crash

fix:

[   10.631533] calling  yenta_socket_init+0x0/0x20
[   10.631533] Yenta: CardBus bridge found at 0000:15:00.0 [17aa:2012]
[   10.631533] Yenta: Using INTVAL to route CSC interrupts to PCI
[   10.631533] Yenta: Routing CardBus interrupts to PCI
[   10.631533] Yenta TI: socket 0000:15:00.0, mfunc 0x01d01002, devctl 0x64
[   10.731599] BUG: unable to handle kernel NULL pointer dereference at 00000040
[   10.731838] IP: [<c0c95b5f>] _spin_lock_irq+0xf/0x20
[   10.732221] *pde = 00000000
[   10.732741] Oops: 0002 [#1] SMP
[   10.733453]
[   10.734253] Pid: 1, comm: swapper Tainted: G        W (2.6.27-rc3-tip-00173-gd7eaa4f-dirty #1)
[   10.735188] EIP: 0060:[<c0c95b5f>] EFLAGS: 00010002 CPU: 0
[   10.735523] EIP is at _spin_lock_irq+0xf/0x20
[   10.735523] EAX: 00000040 EBX: 00000000 ECX: f6e04c90 EDX: 00000100
[   10.735523] ESI: 000000df EDI: f6e04c90 EBP: f7867df0 ESP: f7867df0
[   10.735523]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[   10.735523] Process swapper (pid: 1, ti=f7867000 task=f7870000 task.ti=f7867000)
[   10.735523] Stack: f7867e04 c0155fbd 00000000 00000000 f6e04c90 f7867e5c c0c6e319 c0f6a074
[   10.735523]        f6e04c90 000017aa 00002012 c112b648 f791f240 c112b5e0 f7867e44 c010440b
[   10.735523]        f791f240 f791f29c c112b8ec f791f240 00000000 f7867e5c c048f893 03c0b648
[   10.735523] Call Trace:
[   10.735523]  [<c0155fbd>] ? probe_irq_on+0x3d/0x140
[   10.735523]  [<c0c6e319>] ? yenta_probe+0x529/0x640
[   10.735523]  [<c010440b>] ? mcount_call+0x5/0xa
[   10.735523]  [<c048f893>] ? pci_match_device+0xa3/0xb0
[   10.735523]  [<c048fc1e>] ? pci_device_probe+0x5e/0x80
[   10.735523]  [<c0515423>] ? driver_probe_device+0x83/0x180
[   10.735523]  [<c0515594>] ? __driver_attach+0x74/0x80
[   10.735523]  [<c0514b69>] ? bus_for_each_dev+0x49/0x70
[   10.735523]  [<c051528e>] ? driver_attach+0x1e/0x20
[   10.735523]  [<c0515520>] ? __driver_attach+0x0/0x80
[   10.735523]  [<c05150d3>] ? bus_add_driver+0x1a3/0x220
[   10.735523]  [<c048fb60>] ? pci_device_remove+0x0/0x40
[   10.735523]  [<c05157f4>] ? driver_register+0x54/0x130
[   10.735523]  [<c048fe2f>] ? __pci_register_driver+0x4f/0x90
[   10.735523]  [<c11e9419>] ? yenta_socket_init+0x19/0x20
[   10.735523]  [<c0101125>] ? do_one_initcall+0x35/0x160
[   10.735523]  [<c11e9400>] ? yenta_socket_init+0x0/0x20
[   10.735523]  [<c01391a6>] ? __queue_work+0x36/0x50
[   10.735523]  [<c013922d>] ? queue_work_on+0x3d/0x50
[   10.735523]  [<c11a2758>] ? kernel_init+0x148/0x210
[   10.735523]  [<c11a2610>] ? kernel_init+0x0/0x210
[   10.735523]  [<c01043f3>] ? kernel_thread_helper+0x7/0x10
[   10.735523]  =======================
[   10.735523] Code: 10 38 f2 74 06 f3 90 8a 10 eb f6 5d 89 c8 c3 8d b6 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5 e8 a4 e8 46 ff fa ba 00 01 00 00 90 <66> 0f c1 10 38 f2 74 06 f3 90 8a 10 eb f6 5d c3 90 55 89 e5 53

as auto-probing wants to iterate over existing irqs.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

generic: sparse irqs: use irq_desc() together with dyn_array, instead of irq_desc[]

add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.

Preallocate 32 irq_desc, and irq_desc() will try to get more.

( No change in functionality is expected anywhere, except the odd build
  failure where we missed a code site or where a crossing commit itroduces
  new irq_desc[] usage. )

v2: according to Eric, change get_irq_desc() to irq_desc()

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: remove nr_irq_vectors

remove unused defines derived from the (now obsolete) NR_IRQS define.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86, irq: get nr_irqs from madt

Until now, NR_IRQS was derived from black magic defines that had to
be "large enough" to both accomodate NR_CPUS and MAX_NR_IO_APICs.

This resulted in a way too large irq_desc[] array on most x86 systems.
Especially with larger CPU masks, the size of irq_desc can spiral out
of control quickly.

So be smarter about it and use precise allocation instead: determine the
default maximum possible IRQ number from the ACPI MADT. Use a minimum limit
of at least 32 IRQs for broken BIOSes.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: sparse irqs, fix #3

fix non-APIC UP build:

 arch/x86/kernel/built-in.o: In function `setup_arch':
 : undefined reference to `pin_map_size'
 arch/x86/kernel/built-in.o: In function `setup_arch':
 : undefined reference to `first_free_entry'

Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: use dyn_array in io_apic_xx.c

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: make irqs in kernel stat use per_cpu_dyn_array

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: sparse irqs, export nr_irqs

fix:

  Building modules, stage 2.
  MODPOST 458 modules
  ERROR: "nr_irqs" [drivers/serial/8250.ko] undefined!

Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: make irq_desc to use dyn_array

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: make irq2_iommu to use dyn_array

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irqs: make irq_timer_state to use dyn_array

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/xen: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

fs/proc: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/serial: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/scsi: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/rtc: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/pcmcia: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/pci/ intr remapping: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/net: use nr_irqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

drivers/char: use nr_irqs

convert them to nr_irqs.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: use nr_irqs

also add first_free_entry and pin_map_size, which were NR_IRQS derived
constants.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

irq: introduce nr_irqs

at this point nr_irqs is equal NR_IRQS

convert a few easy users from NR_IRQS to dynamic nr_irqs.

v2: according to Eric, we need to take care of arch without generic_hardirqs

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: enable dyn_array support

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: alloc dyn_array all together

so could spare some memory with small alignment in bootmem

also tighten the alignment checking, and make print out less debug info.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

add per_cpu_dyn_array support

allow dyn-array in per_cpu area, allocated dynamically.

usage:

|  /* in .h */
| struct kernel_stat {
|        struct cpu_usage_stat   cpustat;
|        unsigned int *irqs;
| };
|
|  /* in .c */
| DEFINE_PER_CPU(struct kernel_stat, kstat);
|
| DEFINE_PER_CPU_DYN_ARRAY_ADDR(per_cpu__kstat_irqs, per_cpu__kstat.irqs, sizeof(unsigned int), nr_irqs, sizeof(unsigned long), NULL);

after setup_percpu()/per_cpu_alloc_dyn_array(), the dyn_array in
per_cpu area is ready to use.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

generic: add dyn_array support

Allow crazy big arrays via bootmem at init stage.
Architectures use CONFIG_HAVE_DYN_ARRAY to enable it.

usage:

| static struct irq_desc irq_desc_init __initdata = {
|        .status = IRQ_DISABLED,
|        .chip = &no_irq_chip,
|        .handle_irq = handle_bad_irq,
|        .depth = 1,
|        .lock = __SPIN_LOCK_UNLOCKED(irq_desc->lock),
| #ifdef CONFIG_SMP
|        .affinity = CPU_MASK_ALL
| #endif
| };
|
| static void __init init_work(void *data)
| {
|        struct dyn_array *da = data;
|        struct  irq_desc *desc;
|        int i;
|
|        desc = *da->name;
|
|        for (i = 0; i < *da->nr; i++)
|                memcpy(&desc[i], &irq_desc_init, sizeof(struct irq_desc));
| }
|
| struct irq_desc *irq_desc;
| DEFINE_DYN_ARRAY(irq_desc, sizeof(struct irq_desc), nr_irqs, PAGE_SIZE, init_work);

after pre_alloc_dyn_array() after setup_arch(), the array is ready to be
used.

Via this facility we can replace irq_desc[NR_IRQS] array with dyn_array
irq_desc[nr_irqs].

v2: remove _nopanic in pre_alloc_dyn_array()

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: remove irq_vectors_limits

there's no user left.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

x86: add after_bootmem flag for 32bit

to prepare to use dyn_array support etc.

Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>