Aaro Koskinen [Thu, 29 Jan 2009 16:57:17 +0000 (08:57 -0800)]
ARM: OMAP: gptimer min_delta_ns corrected
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com> Reviewed-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: DMA: Fix uninitialized channel flags
This has similar symptoms than 66c23551b1b774e2be3c7bdf91c0ebf2c7a3519e
where just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch
can cause incorrect dump_stack(). Here it can happen if channel has been
used before and the channel flags variable holds old status.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: Fix race in OMAP2/3 DMA IRQ handling
CSR must be cleared before invoking the callback.
If the callback function starts a new, fast DMA transfer on the same
channel, the completion status might lost if CSR is cleared after
the callback invocation.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Stanley.Miao [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: Fix McBSP spin_lock deadlock
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Wed, 28 Jan 2009 17:01:42 +0000 (09:01 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
Linus Torvalds [Wed, 28 Jan 2009 16:41:57 +0000 (08:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
Kumar Gala [Wed, 28 Jan 2009 06:07:20 +0000 (00:07 -0600)]
dmi: Fix build breakage
Commit d7b1956fed33d30c4815e848fd7a143722916868 ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMI
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
We just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Anholt [Wed, 28 Jan 2009 05:19:41 +0000 (21:19 -0800)]
drm: Rip out the racy, unused vblank signal code.
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net> Requested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerhard Pircher [Fri, 23 Jan 2009 06:51:28 +0000 (06:51 +0000)]
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Robert Jennings [Thu, 22 Jan 2009 09:40:00 +0000 (09:40 +0000)]
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Casey Schaufler [Wed, 28 Jan 2009 03:56:30 +0000 (19:56 -0800)]
smackfs load append mode fix
Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
Anton Vorontsov [Sat, 10 Jan 2009 02:03:21 +0000 (05:03 +0300)]
USB: Driver for Freescale QUICC Engine USB Host Controller
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: option: add QUANTA HSDPA Data Card device ids
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz [Tue, 20 Jan 2009 22:48:36 +0000 (23:48 +0100)]
USB: unusual_dev: usb-storage needs to ignore a device
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>. Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcel Sebek [Sun, 28 Dec 2008 13:06:50 +0000 (14:06 +0100)]
USB: 'option' driver - onda device MT503HS has wrong id
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Phil Dibowitz [Sun, 11 Jan 2009 17:46:20 +0000 (18:46 +0100)]
USB: Remove ZTE modem from unusual_devices
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Sat, 20 Dec 2008 19:56:08 +0000 (12:56 -0700)]
USB: usbmon: Implement compat_ioctl
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Brandon Philips [Mon, 5 Jan 2009 16:30:39 +0000 (08:30 -0800)]
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
Andrew Lunn [Tue, 23 Dec 2008 16:31:23 +0000 (17:31 +0100)]
USB: CDC-ACM quirk for MTK GPS
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
James A. Treacy [Sun, 25 Jan 2009 04:37:43 +0000 (23:37 -0500)]
USB: cdc-acm: support some gps data loggers
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bryan Wu [Wed, 7 Jan 2009 16:21:19 +0000 (00:21 +0800)]
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
David Brownell [Mon, 26 Jan 2009 10:05:43 +0000 (02:05 -0800)]
USB: musb: Kconfig fix
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hugo Villeneuve [Sun, 25 Jan 2009 01:57:30 +0000 (17:57 -0800)]
USB: musb cppi bugfixes
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kalle Valo [Sun, 25 Jan 2009 01:57:15 +0000 (17:57 -0800)]
USB: musb: tusb6010 buildfix
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
No such file or directory
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 25 Jan 2009 01:56:17 +0000 (17:56 -0800)]
USB: musb davinci buildfix
Trying once more to get this merged. The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged. Neither
were any of the numerous subsequent resends. Sigh.
CC drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 25 Jan 2009 01:55:57 +0000 (17:55 -0800)]
USB: omap1 ohci buildfix (otg related)
> > drivers/built-in.o: In function `ohci_omap_init':
> > hid-quirks.c:(.text+0x6c608): undefined reference to `otg_get_transceiver'
> > drivers/built-in.o: In function `omap_udc_probe':
> > hid-quirks.c:(.init.text+0x34c0): undefined reference to `otg_get_transceiver'
> > hid-quirks.c:(.init.text+0x3d40): undefined reference to `otg_put_transceiver'
Reported-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 13 Jan 2009 16:33:42 +0000 (11:33 -0500)]
USB: fix char-device disconnect handling
This patch (as1198) fixes a conceptual bug: Somewhere along the line
we managed to confuse USB class devices with USB char devices. As a
result, the code to send a disconnect signal to userspace would not be
built if both CONFIG_USB_DEVICE_CLASS and CONFIG_USB_DEVICEFS were
disabled.
The usb_fs_classdev_common_remove() routine has been renamed to
usbdev_remove() and it is now called whenever any USB device is
removed, not just when a class device is unregistered. The notifier
registration and unregistration calls are no longer conditionally
compiled. And since the common removal code will always be called as
part of the char device interface, there's no need to call it again as
part of the usbfs interface; thus the invocation of
usb_fs_classdev_common_remove() has been taken out of
usbfs_remove_device().
Commit a0d4922da2e4ccb0973095d8d29f36f6b1b5f703
(USB: fix up suspend and resume for PCI host controllers) attempted
to fix the suspend-resume of PCI USB controllers, but unfortunately
it did that incorrectly and interrupts are left enabled by the USB
controllers' ->suspend_late() callback as a result. This leads to
serious problems during suspend which are very difficult to debug.
Fix the issue by removing the ->suspend_late() callback of PCI
USB controllers and moving the code from there to the ->suspend()
callback executed with interrupts enabled. Additionally, make
the ->resume() callback of PCI USB controllers execute
pci_enable_wake(dev, PCI_D0, false) to disable wake-up from the
full power state (PCI_D0).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Tested-by: "Jeff Chua" <jeff.chua.linux@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: "Zdenek Kabelac" <zdenek.kabelac@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 13 Jan 2009 16:35:54 +0000 (11:35 -0500)]
USB: don't enable wakeup by default for PCI host controllers
This patch (as1199) changes the initial wakeup settings for PCI USB
host controllers. The controllers are marked as capable of waking the
system, but wakeup is not enabled by default.
It turns out that enabling wakeup for USB host controllers has a lot
of bad consequences. As the simplest example, if a USB mouse or
keyboard is unplugged immediately after the computer is put to sleep,
the unplug will cause the system to wake back up again! We are better
off marking them as wakeup-capable and leaving wakeup disabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Rafael J. Wysocki <rjw@sisk.pl> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 15 Jan 2009 22:03:33 +0000 (17:03 -0500)]
USB: fix toggle mismatch in disable_endpoint paths
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dan Streetman <ddstreet@ieee.org> Tested-by: Dan Streetman <ddstreet@ieee.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Wed, 28 Jan 2009 00:07:44 +0000 (16:07 -0800)]
Merge branch 'for-2.6.29' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.29' of git://linux-nfs.org/~bfields/linux:
nfsd: only set file_lock.fl_lmops in nfsd4_lockt if a stateowner is found
nfsd: fix cred leak on every rpc
nfsd: fix null dereference on error path
nfs: note that CONFIG_SUNRPC_XPRT_RDMA turns on server side support too
update port number in NFS/RDMA documentation
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvfc: Fix DMA mapping leak on memory allocation failure
[SCSI] qla2xxx: Update version number to 8.03.00-k2.
[SCSI] qla2xxx: Add checks for a valid fcport in dev-loss-tmo/terminate_rport_io callbacks.
[SCSI] qla2xxx: Correct regression in DMA-mask setting prior to allocations.
[SCSI] qla2xxx: Correct descriptions in flash manipulation routines.
[SCSI] qla2xxx: Correct regression in EH abort handling.
[SCSI] qla2xxx: Correct endianness issue during flash manipulation.
[SCSI] qla2xxx: Correct MSI-X vector allocation for single queue mode.
[SCSI] qla2xxx: Modify firmware-load order precedence for ISP81XX parts.
[SCSI] qla2xxx: Always serialize mailbox command execution.
[SCSI] qla2xxx: Ensure RISC-interrupt-enabled consistency for IS_NOPOLLING_TYPE() ISPs.
[SCSI] qla2xxx: Simplify sector-mask calculation in preparation for larger flash parts.
[SCSI] qla2xxx: Fix memory leak in error path
[SCSI] qla4xxx: do not reuse session when connecting to different target port
[SCSI] libiscsi: fix iscsi pool leak
Move the initialization of irq_default_affinity to early_irq_init as
core_initcall is too late.
irq_default_affinity can be used in init_IRQ and potentially timer and
SMP init as well. All of these happen before core_initcall. Moving
the initialization to early_irq_init ensures that it is initialized
before it is used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com> Acked-by: Mike Travis <travis@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Thu, 22 Jan 2009 19:16:04 +0000 (14:16 -0500)]
nfsd: only set file_lock.fl_lmops in nfsd4_lockt if a stateowner is found
nfsd4_lockt does a search for a lockstateowner when building the lock
struct to test. If one is found, it'll set fl_owner to it. Regardless of
whether that happens, it'll also set fl_lmops. Given that this lock is
basically a "lightweight" lock that's just used for checking conflicts,
setting fl_lmops is probably not appropriate for it.
This behavior exposed a bug in DLM's GETLK implementation where it
wasn't clearing out the fields in the file_lock before filling in
conflicting lock info. While we were able to fix this in DLM, it
still seems pointless and dangerous to set the fl_lmops this way
when we may have a NULL lockstateowner.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: J. Bruce Fields <bfields@pig.fieldses.org>
Linus Torvalds [Tue, 27 Jan 2009 15:50:41 +0000 (07:50 -0800)]
Merge branch 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
SATA PIIX: Blacklist system that spins off disks during ACPI power off
SATA Sil: Blacklist system that spins off disks during ACPI power off
SATA AHCI: Blacklist system that spins off disks during ACPI power off
SATA: Blacklisting of systems that spin off disks during ACPI power off
DMI: Introduce dmi_first_match to make the interface more flexible
Hibernation: Introduce system_entering_hibernation
Eric Paris [Tue, 27 Jan 2009 11:50:37 +0000 (11:50 +0000)]
tty_open can return to userspace holding tty_mutex
__tty_open could return (to userspace) holding the tty_mutex thanks to a
regression introduced by 4a2b5fddd53b80efcb3266ee36e23b8de28e761a ("Move
tty lookup/reopen to caller").
This was found by bisecting an fsfuzzer problem. Admittedly I have no
idea how it managed to tickle this 100% reliably, but it is clearly a
regression and when hit leaves the box in a completely unusable state.
This patch lets the fsfuzzer test complete every time.
Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SATA PIIX: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP 2510p that uses the ata_piix driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SATA Sil: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6325 that uses the sata_sil driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SATA AHCI: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information.
Blacklist HP nx6310 that uses the AHCI driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SATA: Blacklisting of systems that spin off disks during ACPI power off
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
DMI: Introduce dmi_first_match to make the interface more flexible
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.
To prevent this from happening we can blacklist the affected systems
using DMI information. However, only the on-board controlles should
be blacklisted and their PCI slot numbers can be used for this
purpose. Unfortunately the existing interface for checking DMI
information of the system is not very convenient for this purpose,
because to use it, we would have to define special callback functions
or create a separate struct dmi_system_id table for each blacklisted
system.
To overcome this difficulty introduce a new function
dmi_first_match() returning a pointer to the first entry in an array
of struct dmi_system_id elements that matches the system DMI
information. Then, we can use this pointer to access the entry's
.driver_data field containing the additional information, such as
the PCI slot number, allowing us to do the desired blacklisting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce boolean function system_entering_hibernation() returning
'true' during the last phase of hibernation, in which devices are
being put into low power states and the sleep state (for example,
ACPI S4) is finally entered.
Some device drivers need such a function to check if the system is
in the final phase of hibernation. In particular, some SATA drivers
are going to use it for blacklisting systems in which the disks
should not be spun down during the last phase of hibernation (the
BIOS will do that anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Matt Waddel [Sat, 20 Dec 2008 14:16:38 +0000 (07:16 -0700)]
m68knommu: fix 5329 ColdFire periphal addressing
The 5329 ColdFire peripheral IO register addresses are not relative to
the MBAR register. So fix the serial platform setup array and IRQ acking
to use just the direct addresses.
Signed-off-by: Matt Waddel <Matt.Waddel@freescale.com> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Adrian Bunk [Wed, 29 Oct 2008 10:15:47 +0000 (12:15 +0200)]
m68knommu: set NO_DMA
m68knommu does not set the Kconfig NO_DMA variable, but also does
not provide the required functions, resulting in the following
build error triggered by commit a40c24a13366e324bc0ff8c3bb107db89312c984
(net: Add SKB DMA mapping helper functions.):
<-- snip -->
..
LD vmlinux
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac5e): undefined reference to `dma_unmap_single'
net/built-in.o: In function `skb_dma_unmap':
(.text+0xac7a): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xacdc): undefined reference to `dma_map_single'
net/built-in.o: In function `skb_dma_map':
(.text+0xace8): undefined reference to `dma_mapping_error'
net/built-in.o: In function `skb_dma_map':
(.text+0xad10): undefined reference to `dma_map_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xad82): undefined reference to `dma_unmap_page'
net/built-in.o: In function `skb_dma_map':
(.text+0xadc6): undefined reference to `dma_unmap_single'
make[1]: *** [vmlinux] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
John Adamson [Fri, 22 Aug 2008 06:43:49 +0000 (16:43 +1000)]
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
I noticed (the hard way) that the mcf.c driver doesn't support the fractional precision register on the MCF5272. This makes the console dicey at 115200 baud and a system clock of 66.0 MHz. On the other hand, if your hardware is running at 66.666 MHz, it probably isn't a problem.
Patch submitted by John Adamson <jadamson@allen-organ.com>
Part of the code that did not make sense to me got removed by Greg.
This is part two:
The first compare is to check whether the interrupts are disabled or not.
Depending on the result we exectute the RESTORE_ALL macro is not only
restoring the stack but also returning to caller.
The test for pending softirq has been removed because it is allready done
in irq_exit().
Since system_call() is allso using the SAVE_ALL macro and returning via
ret_from_exception label I see no reason why we could not do this here
as well. This is also handy because if we return from the timer interrupt
and we need to resched than we check for this :)
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Jarod Wilson [Thu, 22 Jan 2009 08:58:15 +0000 (19:58 +1100)]
crypto: ccm - Fix handling of null assoc data
Its a valid use case to have null associated data in a ccm vector, but
this case isn't being handled properly right now.
The following ccm decryption/verification test vector, using the
rfc4309 implementation regularly triggers a panic, as will any
other vector with null assoc data:
The above is from a RHEL5-based kernel, but upstream is susceptible too.
The fix is trivial: in crypto/ccm.c:crypto_ccm_auth(), pctx->ilen contains
whatever was in memory when pctx was allocated if assoclen is 0. The tested
fix is to simply add an else clause setting pctx->ilen to 0 for the
assoclen == 0 case, so that get_data_to_compute() doesn't try doing
things its not supposed to.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert Xu [Fri, 16 Jan 2009 03:40:54 +0000 (14:40 +1100)]
crypto: blkcipher - Fix WARN_ON handling in walk_done
When we get left-over bits from a slow walk, it means that the
underlying cipher has gone troppo. However, as we're handling
that case we should ensure that the caller terminates the walk.
This patch does this by setting walk->nbytes to zero.
Linus Torvalds [Tue, 27 Jan 2009 03:21:26 +0000 (19:21 -0800)]
Fix "multiple definition of `debugfs_create_size_t'"
Introduced by 8adb711f3668b034e7b956fac951ed08b53e0d55 ("debugfs:
introduce stub for debugfs_create_size_t() when DEBUG_FS=n") and due to
a simple missing "static inline".
projects / linux-2.6-omap-h63xx.git / log