V4L/DVB (10125): em28xx: Don't do AC97 vendor detection for i2s audio devices

The current code was trying to query the AC97 registers for the vendor
information even if it was clearly not a AC97 audio device (resulting in errors
in the dmesg output).  This was due to a bug in the way we did the check.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10124): em28xx: expand output formats available

Add additional output formats, which will be useful for the Pinnacle PCTV
Ultimate 880e integration with the saa7136.

Thanks to Ray Lu from Empia for providing the em2860/em2880 datasheet.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10123): em28xx: fix reversed definitions of I2S audio modes

Noticed when doing the audio support for the Pinnacle PCTV HD Ultimate 808e
that the modes were incorrect (the 808e uses I2S in 5 sample mode)

Thanks for Ray Lu from Empia for providing the em2860/em2880 datasheet.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10122): em28xx: don't load em28xx-alsa for em2870 based devices

Like the em2874, the em2870 does not have any analog support, so don't bother
loading the em28xx-alsa module.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10121): em28xx: remove worthless Pinnacle PCTV HD Mini 80e device profile

The Pinnacle 80e cannot be supported since Micronas yanked their driver
support for the drx-j chipset at the last minute.  Remove the device profile
since it cannot work without the drx driver and it being there is only likely
to confuse people into thinking the device is supported but not working.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10120): em28xx: remove redundant Pinnacle Dazzle DVC 100 profile

The DVC 100 profile is redundant since we already have an existing identical
profile named "Pinnacle Dazzle DVC 90/DVC 100"

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10119): em28xx: fix corrupted XCLK value

Correct problem introduced during the board refactoring where the XCLK
frequency would get zero'd out.  The sequence of events was as follows:

em28xx_pre_card_setup() called em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration
em28xx_pre_card_setup() would set the dev->board.xclk if not set
em28xx_pre_card_setup() would set the XCLK register based on dev->board.xclk
...
em28xx_card_setup() would call em28xx_set_model()
em28xx_set_model() would memcpy to dev->board configuration (clearing out
 value of dev->board.xclk set in em28xx_pre_card_setup)
...
em28xx_audio_analog_set() sets the XCLK register based on dev->board.xclk
 (which now contains zero)

The change sets the default XCLK and I2C Clock fields in the board definition
inside of em28xx_set_model() so that subsequent calls do not cause the
values to be overwritten.

Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10118): zoran: fix warning for a variable not used

Fix this warning:

drivers/media/video/zoran/zoran_card.c:156: warning: ‘zr36067_pci_tbl’ defined but not used

Currently, zoran driver relies on a find routine that doesn't use the
pci table.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10116): af9013: Fix gcc false warnings

drivers/media/dvb/frontends/af9013.c: In function ‘af9013_set_coeff’:
drivers/media/dvb/frontends/af9013.c:231: warning: ‘ns_coeff2_8k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:230: warning: ‘ns_coeff2_2k’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:229: warning: ‘ns_coeff1_8193nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:228: warning: ‘ns_coeff1_8192nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:227: warning: ‘ns_coeff1_8191nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c:226: warning: ‘ns_coeff1_2048nu’ may be used uninitialized in this function
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_snr’:
drivers/media/dvb/frontends/af9013.c:1012: warning: ‘snr_table’ may be used uninitialized in this function

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10111a): usbvideo.h: remove an useless blank line

This is needed to sync with the development tree. Probably, a merge
conflict were solved by adding this blank line.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10111): quickcam_messenger.c: fix a warning

drivers/media/video/usbvideo/quickcam_messenger.c: In function ‘qcm_sensor_init’:
drivers/media/video/usbvideo/quickcam_messenger.c:450: warning: operation on ‘ret’ may be undefined

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10110): v4l2-ioctl: Fix warnings when using .unlocked_ioctl = __video_ioctl2

This patch fixes this warning:

drivers/media/video/gspca/gspca.c:1811: warning: initialization from incompatible pointer type

The reason is that the returned argument should be a long, not an
integer.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10109): anysee: Fix usage of an unitialized function

drivers/media/dvb/dvb-usb/anysee.c: In function ‘anysee_master_xfer’:
drivers/media/dvb/dvb-usb/anysee.c:156: warning: ‘ret’ may be used uninitialized

By looking at the function, altrough very unlikely, this might
eventually be true if num  = 0. So, better to fix the warning by
initializing with ret = 0.

Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10104): uvcvideo: Add support for video output devices

Extend the range of supported UVC devices by allowing video output devices
matching the following structure:

TT_STREAMING -> VC_PROCESSING_UNIT -> VC_EXTENSION_UNIT{0,n} -> OTT_*

Video output devices are reported with the V4L2_CAP_VIDEO_OUTPUT capability
flag and are subject to the same restrictions as video input devices.

Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10102): uvcvideo: Ignore interrupt endpoint for built-in iSight webcams.

Built-in iSight webcams have an interrupt endpoint but spit proprietary data
that don't conform to the UVC status endpoint messages. Don't try to handle
the interrupt endpoint for those cameras.

Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10101): uvcvideo: Fix bulk URB processing when the header is erroneous

When the first bulk URB of a video payload contains an erroneous header, or
when no V4L2 buffer is available, the whole payload must be dropped. Change
the skip logic to drop all bulk URBs until the end of the payload instead of
the first one only.

Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10099): soc-camera: add support for MT9T031 CMOS camera sensor from Micron

This camera is rather similar to MT9M001, but also has a couple of
enhanced features, like pixel binning.

 create mode 100644 drivers/media/video/mt9t031.c

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10098): ov772x: fix try_fmt calculation method

Don't modify driver's state in try_fmt, just verify format acceptability
or adjust it to driver's capabilities.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10097): ov772x: clear i2c client data on error and remove

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10096): ov772x: change dev_info to dev_dbg

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10095): The failure of set_fmt is solved in tw9910

priv->scale is checked in start_capture.
Therefore, it should be NULL if failing in set_fmt.
This patch resolve this problem.

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10094): Add tw9910 driver

This patch adds tw9910 driver that use soc_camera framework.
It was tested on SH Migo-r board and mplayer.

 create mode 100644 drivers/media/video/tw9910.c
 create mode 100644 include/media/tw9910.h

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10093): soc-camera: add new bus width and signal polarity flags

In preparation for i.MX31 camera host driver add flags for 4 and 15 bit bus
widths and for data lines polarity inversion.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10092): Change V4L2 field to ANY from NONE on sh_mobile_ceu_camera.c

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10091): mt9m001 mt9v022: simplify pointer derefernces

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10090): soc-camera: let drivers decide upon supported field values

sh_mobile_ceu_camera.c is already prepared to support interlaced format, this
patch moves the choice of a field type down to host and / or camera drivers.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10089): Add interlace support to sh_mobile_ceu_camera.c

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10088): video: sh_mobile_ceu cleanups and comments

This patch cleans up the sh_mobile_ceu driver and adds comments and
constants to clarify the magic sequence in sh_mobile_ceu_capture().

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10087): Add new enum_input function on soc_camera

This patch presents new method to be able to select V4L2 input type

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10086): Add new set_std function on soc_camera

This patch presents new method to be able to check v4l2_std_id

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10085): sh_mobile_ceu: add NV16 and NV61 support

This patch adds NV16/NV61 support to the sh_mobile_ceu driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10084): sh_mobile_ceu: add NV12 and NV21 support

This patch adds NV12/NV21 support to the sh_mobile_ceu driver.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10083): soc-camera: unify locking, play nicer with videobuf locking

Move mutex from host drivers to camera device object, take into account
videobuf locking.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10081): pxa-camera: call try_fmt() camera device method with correct pixel format

With the introduction of the format conversion support in soc-camera, we now
also have to take care to pass the correct pixel format to the camera driver
when calling its try_fmt() method.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10080): soc-camera: readability improvements, more strict operations checks

Simplify multiple drivers by replacing f->fmt.pix.* with a single pointer
dereference, merge some needlessly broken lines, verify host and camera
operations pointers on registration.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10079): sh_mobile_ceu: use new pixel format translation code

This patch converts the sh_mobile_ceu driver to make use
of the new pixel format translation code. Only pass-though
mode at this point.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10078): video: add NV16 and NV61 pixel formats

This patch adds support for NV16 and NV61 pixel formats.

These pixel formats use two planes; one for 8-bit Y values and
one for interleaved 8-bit U and V values. NV16/NV61 formats are
very similar to NV12/NV21 with the exception that NV16/NV61 are
using the same number of lines for both planes. The difference
between NV16 and NV61 is the U and V byte order.

The fourcc values are extrapolated from the NV12/NV21 case.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10077): mt9m111: add support for mt9m112 since sensors seem identical

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10076): v4l: add chip ID for MT9M112 camera sensor from Micron

The chip is largely compatible with MT9M111 and is going to be supported by the
same driver.

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10075): pxa-camera: setup the FIFO inactivity time-out register

Using PXA270's FIFO inactivity time-out register (CITOR) reduces FIFO overruns.
The time-out is calculated in CICLK / LCDCLK ticks and has to be longer than
one pixel time. For this we have to know the pixel clock frequency, which
usually is provided by the camera. We use the struct soc_camera_sense to
request PCLK frequency from the camera driver upon each data format change.

Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10074): soc-camera: add camera sense data

Add a struct soc_camera_sense, that can be used by camera host drivers to
request additional information from a camera driver, for example, when
changing data format. This struct can be extended in the future, its first use
is to request the camera driver whether the pixel-clock frequency has changed.

Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10073): mt9m111: Add automatic white balance control

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10072): soc-camera: Add signal inversion flags to be used by camera drivers

As reported by Antonio Ospite <ospite@studenti.unina.it> two platforms with a
mt9m111 camera require opposite pixel clock polarity, which means one of them
inverts it. This patch adds support for inversion flags and switches all
available camera drivers to using them.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB: pxa-camera: use memory mapped IO access for camera (QCI) registers

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10107): More than one driver defines the same var name (dump_bridge). Add

"static" on stv06xx for all static functions and parameters to avoid
such troubles.

Cc: Erik Andren <erik.andren@gmail.com>
Cc: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10106): gscpa - stv06xx: Fix compilation with kernel tree

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10069): Add ov7725 support to ov772x driver

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10068): Change device ID selection method on ov772x driver

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10067): Remove ov772x_default_regs from ov772x driver

Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10066): mt9m001 mt9v022: fix bus-width switch GPIO availability test

Testing for non-NULL platform-data is not enough, we have to check if the GPIO
in the platform data is valid or not. Also see my earlier patch:

[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10065): mt9m111: add all yuv format combinations.

The Micron mt9m111 offers 4 byte orders for YCbCr
output. This patchs adds all possible outputs capabilities
to the mt9m111 driver.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10064): mt9m111: mt9m111_get_global_gain() - unsigned >= 0 is always true

unsigned >= 0 is always true and fix formula

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10062): dsbr100: change return values in 3 functions

Patch replace return -1; with return retval; in 3 functions.
And we also change if-checks for this returned values.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10061): dsbr100: increase driver version

Due to a lot of patches for dsbr100 last time we should update version
of driver.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10060): dsbr100: fix and add right comments

Fix and add right comments. Few empty lines removed.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10059): dsbr100: dev_err instead of dev_warn

We should use dev_err (not dev_warn) if video_register_device fails.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10058): dsbr100: fix codingstyle, add dev_err messages

We should make if-constructions more clear. Introduce int retval
variables in some functions to make it this way. Also a lot of useful
dev_err messages added. And now we check every returned value after
usb_control_msg.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10057): dsbr100: place dev_warn instead of printk

Remove printk in one line and place dev_warn there.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10056): em28xx: Add snapshot button on Pixelview Prolink PlayTV USB 2.0

Added snapshot feature for Pixelview Prolink PlayTV USB 2.0

Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10055): em28xx: Add entry for PixelView PlayTV Box 4

Added board PixelView PlayTV Box 4
Thanks to Vildenei Negrao Pereira <neodarkaman@brturbo.com.br> for testing and data collection.

Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10054): dsbr100: fix unplug oops

This patch corrects unplug procedure. Patch adds
usb_dsbr100_video_device_release, new macros - videodev_to_radio, mutex
lock and a lot of safety checks.
Struct video_device videodev is embedded in dsbr100_device structure.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10053): radio-mr800: disable autosuspend support

Because this device doesn't provide any powermanagment capabilities(may
be they exist but unknown to me yet, so they are not implemented), we
should turn them off. Patch sets support_autosuspend equal to 0.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10052): radio-mr800: correct unplug, fix to previous patch

This patch corrects unplug procedure, that was implemented wrong in
previous patch. New function usb_amradio_device_release added.
Disconnect lock removed.

Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10050): gspca - vc032x: Webcam 046d:0897 added.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10049): gspca - many subdrivers: Set 'const' the pixel format table.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10048): gspca - stv06xx: New subdriver.

Signed-off-by: Erik Andren <erik.andren@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10046): gspca - ov534: Use the gspca usb buf for usb control messages.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10045): gspca - ov534: Remove empty line in trace.

Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10044): gspca - pac7311: Webcam 093a:2620 added.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10041): m5602 - rework parts of the resolution initialization

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10040): m5602 - ov9650: Activate variopixel

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10039): m5602 - ov9650: Add CIF mode

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10038): m5602: tweak the hsync. Remove redundant init sequence

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10037): m5602: add QVGA mode for the ov9650 sensor

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10036): m5602 - ov9650: Prepare the sensor to set multiple resolutions

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10035): m5602: add a start sending hook in the sensor struct

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10034): m5602: fixup offset in order to align image

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10033): m5602: add some comments

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10032): m5602: add vflip quirk for Alienware m9700

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10031): m5602: correct the name of the Pascal Stangs library

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10030): m5602: Use read/modify/write when toggling vflip on the po1030

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10029): m5602: remove uneeded test on po1030

The po1030 never sends long i2c messages, no need to test for that in
the init phase.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10028): mt5602: Remove the s5k83a specific read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10027): m5602: convert the s5k83a sensor to use the common function

Convert the s5k83a sensor to use the common read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10026): m5602: remove the s5k4aa implementation of the read_sensor

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10025): m5602: convert the s5k4aa sensor to use the common function

Convert the s5k4aa sensor to use the common read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10024): m5602: Remove the mt9m111 implementation of the read_sensor function.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10023): m5602: Convert the mt9m111 to use the common read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10022): m5602: Remove the po1030 read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10021): m5602: Let the po1030 use the common read_sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10020): m5602: Remove the ov9650 implementation of the read sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10019): m5602: Let the ov9650 use the common read sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10018): gspca - m5602 - ov9650: Use generic read_sensor function

Toggle read sensor sequence depending on type of sensor. Check that no
more than max width of a sensor is read.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10015): gspca - m5602: Add initial read sensor implementation

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10014): gspca - m5602: Remove all sensor specific write functions.

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10013): Convert all sensors to use the unified write sensor function

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10012): m5602: Start to unify read/write sensor functions

First step into unifying the read and write sensor functions

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10011): m5602: Remove the write and read sensor from the main struct

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10010): gspca - m5602: Add vflip quirk for the ASUS A6Ja

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

V4L/DVB (10009): gspca - m5602: Convert some functions to be static

Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>