While memory hotplug allocate/free memmap, page_cgroup doesn't free
page_cgroup at OFFLINE when page_cgroup is allocated via bootomem.
(Because freeing bootmem requires special care.)
Then, if page_cgroup is allocated by bootmem and memmap is freed/allocated
by memory hotplug, page_cgroup->page == page is no longer true.
But current MEM_ONLINE handler doesn't check it and update
page_cgroup->page if it's not necessary to allocate page_cgroup. (This
was not found because memmap is not freed if SPARSEMEM_VMEMMAP is y.)
And I noticed that MEM_ONLINE can be called against "part of section".
So, freeing page_cgroup at CANCEL_ONLINE will cause trouble. (freeing
used page_cgroup) Don't rollback at CANCEL.
One more, current memory hotplug notifier is stopped by slub because it
sets NOTIFY_STOP_MASK to return vaule. So, page_cgroup's callback never
be called. (low priority than slub now.)
I think this slub's behavior is not intentional(BUG). and fixes it.
Another way to be considered about page_cgroup allocation:
- free page_cgroup at OFFLINE even if it's from bootmem
and remove specieal handler. But it requires more changes.
Nick Piggin [Mon, 1 Dec 2008 21:13:47 +0000 (13:13 -0800)]
mm: vmalloc fix lazy unmapping cache aliasing
Jim Radford has reported that the vmap subsystem rewrite was sometimes
causing his VIVT ARM system to behave strangely (seemed like going into
infinite loops trying to fault in pages to userspace).
We determined that the problem was most likely due to a cache aliasing
issue. flush_cache_vunmap was only being called at the moment the page
tables were to be taken down, however with lazy unmapping, this can happen
after the page has subsequently been freed and allocated for something
else. The dangling alias may still have dirty data attached to it.
The fix for this problem is to do the cache flushing when the caller has
called vunmap -- it would be a bug for them to write anything else to the
mapping at that point.
That appeared to solve Jim's problems.
Reported-by: Jim Radford <radford@blackbean.org> Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 2 Dec 2008 02:56:55 +0000 (18:56 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: fix regression in ocfs2_read_blocks_sync()
ocfs2: fix return value set in init_dlmfs_fs()
ocfs2: Small documentation update
ocfs2: fix wake_up in unlock_ast
ocfs2: initialize stack_user lvbptr
ocfs2: comments typo fix
Mark Fasheh [Fri, 21 Nov 2008 22:06:55 +0000 (14:06 -0800)]
ocfs2: fix regression in ocfs2_read_blocks_sync()
We're panicing in ocfs2_read_blocks_sync() if a jbd-managed buffer is seen.
At first glance, this seems ok but in reality it can happen. My test case
was to just run 'exorcist'. A struct inode is being pushed out of memory but
is then re-read at a later time, before the buffer has been checkpointed by
jbd. This causes a BUG to be hit in ocfs2_read_blocks_sync().
Reviewed-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Coly Li [Mon, 17 Nov 2008 04:38:22 +0000 (12:38 +0800)]
ocfs2: fix return value set in init_dlmfs_fs()
In init_dlmfs_fs(), if calling kmem_cache_create() failed, the code will use return value from
calling bdi_init(). The correct behavior should be set status as -ENOMEM before going to "bail:".
Signed-off-by: Coly Li <coyli@suse.de> Acked-by: Sunil Mushran <sunil.mushran@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Linus Torvalds [Mon, 1 Dec 2008 19:23:33 +0000 (11:23 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
[libata] pata_rb532_cf: fix signature of the xfer function
[libata] pata_rb532_cf: fix and rename register definitions
ata_piix: add borked Tecra M4 to broken suspend list
Linus Torvalds [Mon, 1 Dec 2008 19:01:54 +0000 (11:01 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
Tejun Heo [Thu, 27 Nov 2008 04:36:48 +0000 (13:36 +0900)]
libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Phil Sutter [Fri, 28 Nov 2008 19:48:35 +0000 (20:48 +0100)]
[libata] pata_rb532_cf: fix signature of the xfer function
Per definition, this function should return the number of bytes
consumed. As the original parameter "buflen" is being decremented inside
the read/write loop, save it in "retlen" at the beginning.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Phil Sutter [Fri, 28 Nov 2008 19:48:26 +0000 (20:48 +0100)]
[libata] pata_rb532_cf: fix and rename register definitions
The original standalone driver uses a custom address for the error
register. Use it in pata_rb532_cf, too.
Rename two register definitions:
- The address offset 0x0800 in fact is the ATA base, not ATA command
address.
- The offset 0x0C00 is not a regular ATA data address, but a buffered one
allowing 4-byte IO.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Sat, 29 Nov 2008 13:37:21 +0000 (22:37 +0900)]
ata_piix: add borked Tecra M4 to broken suspend list
Tecra M4 sometimes forget what it is and reports bogus data via DMI
which makes the machine evade broken suspend matching and thus fail
suspend/resume. This patch updates piix_broken_suspend() such that it
can match such case. As the borked DMI data is a bit generic,
matching many entries to make the match more specific is necessary.
As the usual DMI matching is limited to four entries, this patch uses
hard coded manual matching.
This is reported by Alexandru Romanescu.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When resizing a CQ, MTTs associated with the old CQE buffer were not
freed. As a result, if any app used resize CQ repeatedly, all MTTs
were eventually exhausted, which led to all memory registration
operations failing until the driver is reloaded.
Once the RESIZE_CQ command returns successfully from FW, FW no longer
accesses the old CQ buffer, so it is safe to deallocate the MTT
entries used by the old CQ buffer.
Finally, if the RESIZE_CQ command fails, the MTTs allocated for the
new CQEs buffer also need to be de-allocated.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stefan Roscher [Mon, 1 Dec 2008 18:05:50 +0000 (10:05 -0800)]
IB/ehca: Fix problem with generated flush work completions
This fix enables ehca device driver to generate flush work completions
even if the application doesn't request completions for all work
requests. The current implementation of ehca will generate flush work
completions for the wrong work requests if an application uses non
signaled work completions.
Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Joachim Fenkes [Mon, 1 Dec 2008 18:05:44 +0000 (10:05 -0800)]
IB/ehca: Change misleading error message on memory hotplug
The error message printed when the eHCA driver prevents memory hotplug
is misleading -- the user might think that hot-removing the lhca,
hotplugging memory, then hot-adding the lhca again will work, but it
actually doesn't.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Mon, 1 Dec 2008 17:34:23 +0000 (09:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: fix race condition in state change
ieee1394: fix list corruption (reported at module removal)
firewire: fw-sbp2: another iPod mini quirk entry
ieee1394: sbp2: another iPod mini quirk entry
Linus Torvalds [Mon, 1 Dec 2008 16:33:59 +0000 (08:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Apple ALU wireless keyboards are bluetooth devices
HID: remove setup mutex, fix possible deadlock
HID: add USB ID for another dual gameron adapter
HID: unignore mouse on unibody macbooks
HID: fix blacklist entries for greenasia/pantherlord
Kevin Hao [Mon, 1 Dec 2008 11:36:16 +0000 (11:36 +0000)]
Add kref to fake tty used by USB console
We alloc a fake tty in usb serial console setup function. we should
init the tty's kref otherwise we will face WARN_ON after following
invoke of tty_port_tty_set --> tty_kref_get.
Signed-off-by: Kevin Hao <kexin.hao@windriver.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Newton [Mon, 1 Dec 2008 11:36:06 +0000 (11:36 +0000)]
drivers/char/tty_io.c: Avoid panic when no console is configured.
When no console is configured tty_open tries to call kref_get on a NULL
pointer, return ENODEV instead.
Signed-off-by: Will Newton <will.newton@gmail.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: serial: add more Onda device ids to option driver
USB: usb-storage: unusual_devs entry for Nikon D2H
USB: storage: unusual_devs entry for Mio C520-GPS
USB: fsl_usb2_udc: Report disconnect before unbinding
USB: fsl_qe_udc: Report disconnect before unbinding
USB: fix SB600 USB subsystem hang bug
Revert "USB: improve ehci_watchdog's side effect in CPU power management"
Requested-by: David Miller <davem@davemloft.net> Acked-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Stern [Fri, 21 Nov 2008 21:15:12 +0000 (16:15 -0500)]
USB: storage: unusual_devs entry for Mio C520-GPS
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS
unit. Other devices also based on the Mitac hardware use the same USB
interface firmware, so the Vendor and Product names are generalized.
Anton Vorontsov [Thu, 13 Nov 2008 11:57:20 +0000 (14:57 +0300)]
USB: fsl_qe_udc: Report disconnect before unbinding
Gadgets disable endpoints in their disconnect callbacks, so
we must call disconnect before unbinding. This also fixes
muram memory leak, since we free muram in the qe_ep_disable().
But mainly the patch fixes following badness:
root@b1:~# insmod fsl_qe_udc.ko
fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0
fsl_qe_udc e01006c0.usb: QE USB controller initialized as device
root@b1:~# insmod g_ether.ko
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC be:2d:3c:fa:be:f0
usb0: HOST MAC 62:b8:6a:df:38:66
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether
g_ether gadget: high speed config #1: CDC Ethernet (ECM)
root@b1:~# rmmod g_ether.ko
------------[ cut here ]------------
Badness at drivers/usb/gadget/composite.c:871
[...]
NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether]
LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
Call Trace:
[cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable)
[cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc]
[cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether]
[cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c
[cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38
[...]
fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Shane Huang [Tue, 25 Nov 2008 07:12:33 +0000 (15:12 +0800)]
USB: fix SB600 USB subsystem hang bug
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang
symptom. The USB subsystem hang symptom is observed when the system has
multiple USB devices connected to it. In some cases a USB hub may be required
to observe this symptom.
It was the wrong thing to do, and does not really do what it said
it did.
Cc: Yi Yang <yi.y.yang@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Milton Miller [Sun, 16 Nov 2008 11:44:42 +0000 (11:44 +0000)]
powerpc: Fix build for 32-bit SMP configs
attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the
attribute removal with the same condition. This fixes this build error
on 32-bit SMP configurations:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function)
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.)
Linus Torvalds [Mon, 1 Dec 2008 00:45:13 +0000 (16:45 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.
Linus Torvalds [Mon, 1 Dec 2008 00:44:18 +0000 (16:44 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
Linus Torvalds [Mon, 1 Dec 2008 00:39:06 +0000 (16:39 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
Paul Mackerras [Sun, 30 Nov 2008 11:49:45 +0000 (11:49 +0000)]
powerpc: Fix system calls on Cell entered with XER.SO=1
It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING
= y, if a program sets the SO (summary overflow) bit in the XER and
then does a system call, the SO bit in CR0 will be set on return
regardless of whether the system call detected an error. Since CR0.SO
is used as the error indication from the system call, this means that
all system calls appear to fail.
The reason is that the workaround for the timebase bug on Cell uses a
compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the
ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a
compare instruction, which copies XER.SO to CR0.SO. Since we were
doing this in the system call entry patch after clearing CR0.SO but
before saving the CR, this meant that the saved CR image had CR0.SO
set if XER.SO was set on entry.
This fixes it by moving the clearing of CR0.SO to after the
ACCOUNT_CPU_USER_ENTRY call in the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Arnd Bergmann [Fri, 28 Nov 2008 09:51:24 +0000 (09:51 +0000)]
powerpc/cell: Fix GDB watchpoints, again
An earlier patch from Jens Osterkamp attempted to fix GDB
watchpoints by enabling the DABRX register at boot time.
Unfortunately, this did not work on SMP setups, where
secondary CPUs were still using the power-on DABRX value.
This introduces the same change for secondary CPUs on cell
as well.
Arnd Bergmann [Fri, 28 Nov 2008 09:51:23 +0000 (09:51 +0000)]
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Arnd Bergmann [Fri, 28 Nov 2008 09:51:22 +0000 (09:51 +0000)]
powerpc/cell/axon-msi: Retry on missing interrupt
The MSI capture logic for the axon bridge can sometimes
lose interrupts in case of high DMA and interrupt load,
when it signals an MSI interrupt to the MPIC interrupt
controller while we are already handling another MSI.
Each MSI vector gets written into a FIFO buffer in main
memory using DMA, and that DMA access is normally flushed
by the actual interrupt packet on the IOIF. An MMIO
register in the MSIC holds the position of the last
entry in the FIFO buffer that was written. However,
reading that position does not flush the DMA, so that
we can observe stale data in the buffer.
In a stress test, we have observed the DMA to arrive
up to 14 microseconds after reading the register.
This patch works around this problem by retrying the
access to the FIFO buffer.
We can reliably detect the conditioning by writing
an invalid MSI vector into the FIFO buffer after
reading from it, assuming that all MSIs we get
are valid. After detecting an invalid MSI vector,
we udelay(1) in the interrupt cascade for up to
100 times before giving up.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
I've reproduced this on 2.6.27.7. It is caused by commit 8f64e1f2d1e09267ac926e15090fd505c1c0cbcb ("powerpc: Reserve in bootmem
lmb reserved regions that cross NUMA nodes").
The problem is that Jon took a loop which was (in pseudocode):
The issue comes in when the 'careful_alloc()' is called on a node with
no memory. It falls back to using bootmem from a previously-initialized
node. But, bootmem has not yet been reserved when Jon's patch is
applied. It gives back bogus memory (0xc000000000000000) and pukes
later in boot.
The following patch collapses the loop back together. It also breaks
the mark_reserved_regions_for_nid() code out into a function and adds
some comments. I think a huge part of introducing this bug is because
for loop was too long and hard to read.
Currently, some PCIe devices on POWER6 machines do not get interrupts
assigned correctly. The problem is that OF doesn't create an
"interrupt" property for them. The fix is for of_irq_map_pci to fall
back to using the value in the PCI interrupt-pin register in config
space, as we do when there is no OF device-tree node for the device.
I have verified that this works fine with a pair of Squib-E SAS
adapter on a P6-570.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: struct device - replace bus_id with dev_name(), dev_set_name()
parisc: fix kernel crash when unwinding a userspace process
parisc: __kernel_time_t is always long
Linus Torvalds [Sun, 30 Nov 2008 21:06:47 +0000 (13:06 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: prevent divide by zero error in cpu_avg_load_per_task, update
sched, cpusets: fix warning in kernel/cpuset.c
sched: prevent divide by zero error in cpu_avg_load_per_task
Linus Torvalds [Sun, 30 Nov 2008 21:06:20 +0000 (13:06 -0800)]
Merge branch 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq.h: fix missing/extra kernel-doc
genirq: __irq_set_trigger: change pr_warning to pr_debug
irq: fix typo
x86: apic honour irq affinity which was set in early boot
genirq: fix the affinity setting in setup_irq
genirq: keep affinities set from userspace across free/request_irq()
Linus Torvalds [Sun, 30 Nov 2008 21:01:04 +0000 (13:01 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: always define DECLARE_PCI_UNMAP* macros
x86: fixup config space size of CPU functions for AMD family 11h
x86, bts: fix wrmsr and spinlock over kmalloc
x86, pebs: fix PEBS record size configuration
x86, bts: turn macro into static inline function
x86, bts: exclude ds.c from build when disabled
arch/x86/kernel/pci-calgary_64.c: change simple_strtol to simple_strtoul
x86: use limited register constraint for setnz
xen: pin correct PGD on suspend
x86: revert irq number limitation
x86: fixing __cpuinit/__init tangle, xsave_cntxt_init()
x86: fix __cpuinit/__init tangle in init_thread_xstate()
oprofile: fix an overflow in ppro code
Linus Torvalds [Sun, 30 Nov 2008 21:00:21 +0000 (13:00 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Save/restore HWS_PGA on suspend/resume
drm: move drm vblank initialization/cleanup to driver load/unload
drm/i915: execbuffer pins objects, no need to ensure they're still in the GTT
drm/i915: Always read pipestat in irq_handler
drm/i915: Subtract total pinned bytes from available aperture size
drm/i915: Avoid BUG_ONs on VT switch with a wedged chipset.
drm/i915: Remove IMR masking during interrupt handler, and restart it if needed.
drm/i915: Manage PIPESTAT to control vblank interrupts instead of IMR.
Linus Torvalds [Sun, 30 Nov 2008 19:43:41 +0000 (11:43 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: ignore out-of-range PstateStatus value
[CPUFREQ] Documentation: Add Blackfin to list of supported processors
Linus Torvalds [Sun, 30 Nov 2008 19:36:57 +0000 (11:36 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Check model for Dell 92HD73xx laptops
ALSA: hda - mark Dell studio 1535 quirk
ALSA: hda - No 'Headphone as Line-out' swich without line-outs
ALSA: hda - Fix AFG power management on IDT 92HD* codecs
ALSA: hda - Fix caching of SPDIF status bits
ALSA: hda - Add a quirk for Dell Studio 15
ALSA: hda: Add STAC_DELL_M4_3 quirk
sound/sound_core: Fix sparse warnings
ALSA: hda: STAC_DELL_M6 EAPD
Linus Torvalds [Sun, 30 Nov 2008 19:34:17 +0000 (11:34 -0800)]
Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6
* 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6:
UBI: Don't exit from ubi_thread until kthread_should_stop() is true
UBI: fix EBADMSG handling
Robert P. J. Day [Fri, 28 Nov 2008 11:48:37 +0000 (11:48 +0000)]
MN10300: Tighten up the code using case ranges
Compress a set of consecutive switch cases into a case-range.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 30 Nov 2008 19:06:40 +0000 (11:06 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
toshiba_acpi: close race in toshiba_acpi driver
ACPICA: disable _BIF warning
ACPI: delete OSI(Linux) DMI dmesg spam
ACPICA: Allow _WAK method to return an Integer
ACPI: thinkpad-acpi: fix fan sleep/resume path
sony-laptop: printk tweak
sony-laptop: brightness regression fix
Revert "ACPI: don't enable control method power button as wakeup device when Fixed Power button is used"
ACPI suspend: Blacklist boxes that require us to set SCI_EN directly on resume
ACPI: scheduling in atomic via acpi_evaluate_integer ()
ACPI: battery: Convert discharge energy rate to current properly
ACPI: EC: count interrupts only if called from interrupt handler.
Linus Torvalds [Sun, 30 Nov 2008 19:05:21 +0000 (11:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Mon, 24 Nov 2008 00:57:36 +0000 (16:57 -0800)]
input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
ml_ff_playback() uses spin_(un)lock_bh. However this function is called
with interrupts disabled from erase_effect() in drivers/input/ff-core.c:196.
This is not permitted, and will result in a WARN_ON in the bottom half handling code.
This patch changes this function to just use spin_lock_irqsave() instead, solving
the problem and simplifying the locking logic.
This was reported as entry #106559 in kerneloops.org
Reported-by: kerneloops.org Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:36:54 +0000 (17:36 +0000)]
tricky one: hisax sections
a) hisax_init_pcmcia() needs to be defined only if we have
CONFIG_HOTPLUG (no PCMCIA support otherwise) and can be declared
__devinit.
b) HiSax_inithardware() can go __init
c) hisax_register() is passing to checkcard() full-blown hisax_cs_setup_card():
checkcard(i, id, NULL, hisax_d_if->owner, hisax_cs_setup_card);
The problem with it is that
* hisax_cs_setup_card() is __devinit
* hisax_register() is not
* hisax_cs_setup_card() is a switch from hell, calling a lot of
setup_some_weirdcard() depending on card->typ. _These_ are also
__devinit.
However, in hisax_register() we have card->typ equal to
ISDN_CTYPE_DYNAMIC, which reduces hisax_cs_setup_card() to "nevermind
all that crap, just do nothing and return 2". So we add a
trimmed-down callback doing just that and passed to checkcard() by
hisax_register(). _This_ is non-init (we can stand the impact on
.text size).
Voila - no section warnings from drivers/isdn
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:35:54 +0000 (17:35 +0000)]
m32r: section noise in head.S
usual "introduce .text.head, put it in front of TEXT_TEXT in vmlinux.lds.S,
make the stuff up to jump to start_kernel live in it", same as on other
targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:35:44 +0000 (17:35 +0000)]
section misannotation in ibmtr_cs
ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether
that's the right thing to do there is a separate question, but
since it's PCMCIA and thus will never compile without HOTPLUG...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:35:34 +0000 (17:35 +0000)]
ixgbe section fixes
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:35:04 +0000 (17:35 +0000)]
of_platform_driver noise on sparce
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:34:54 +0000 (17:34 +0000)]
advansys fix on ISA-less configs
The code
if (shost->dma_channel != NO_ISA_DMA)
free_dma(shost->dma_channel);
in there is triggerable only if we have CONFIG_ISA (we only set ->dma_channel to
something other than NO_ISA_DMA under #ifdef CONFIG_ISA). OTOH, free_dma() is
not guaranteed to be there in absense of CONFIG_ISA. IOW, driver runs into
undefined symbols on PCI-but-not-ISA configs (e.g. on frv) and it's a false
positive.
Fix: put the entire if () under #ifdef CONFIG_ISA; behaviour doesn't change and
dependency on free_dma() disappears for !CONFIG_ISA.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sat, 22 Nov 2008 17:33:54 +0000 (17:33 +0000)]
sparc32 cpuinit flase positives
All noise since we don't have CPU hotplug there. However, they
did expose something very odd-looking in there - poke_viking()
does a bunch of identical btfixup each time it's called (i.e.
for each CPU). That one is left alone for now; just the trivial
misannotation fixes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ingo Molnar [Sat, 29 Nov 2008 19:45:15 +0000 (20:45 +0100)]
sched: prevent divide by zero error in cpu_avg_load_per_task, update
Regarding the bug addressed in:
4cd4262: sched: prevent divide by zero error in cpu_avg_load_per_task
Linus points out that the fix is not complete:
> There's nothing that keeps gcc from deciding not to reload
> rq->nr_running.
>
> Of course, in _practice_, I don't think gcc ever will (if it decides
> that it will spill, gcc is likely going to decide that it will
> literally spill the local variable to the stack rather than decide to
> reload off the pointer), but it's a valid compiler optimization, and
> it even has a name (rematerialization).
>
> So I suspect that your patch does fix the bug, but it still leaves the
> fairly unlikely _potential_ for it to re-appear at some point.
>
> We have ACCESS_ONCE() as a macro to guarantee that the compiler
> doesn't rematerialize a pointer access. That also would clarify
> the fact that we access something unsafe outside a lock.
So make sure our nr_running value is immutable and cannot change
after we check it for nonzero.
Ingo Molnar [Tue, 25 Nov 2008 09:27:49 +0000 (10:27 +0100)]
sched, cpusets: fix warning in kernel/cpuset.c
this warning:
kernel/cpuset.c: In function ‘generate_sched_domains’:
kernel/cpuset.c:588: warning: ‘ndoms’ may be used uninitialized in this function
triggers because GCC does not recognize that ndoms stays uninitialized
only if doms is NULL - but that flow is covered at the end of
generate_sched_domains().
Help out GCC by initializing this variable to 0. (that's prudent anyway)
Also, this function needs a splitup and code flow simplification:
with 160 lines length it's clearly too long.
projects / linux-2.6-omap-h63xx.git / log