Steven Toth [Thu, 14 Sep 2006 18:41:13 +0000 (15:41 -0300)]
V4L/DVB (4638): Basic DVB-T and analog TV support for the HVR1300.
This is the first in a series of patches to add full WinTV-HVR1300
support to Linux. This first patch will enable analog TV support
and DVB-T support. Later patches will add the hardware MPEG encoder
support.
Signed-off-by: Steven Toth <stoth@hauppauge.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4637): Add a default method for VIDIOC_G_PARM
For most drivers, VIDIOC_G_PARM will just return the current standard fps.
So, instead of failing, drivers based on video_ioctl2 will implement the
default method.
Alan Cox [Thu, 14 Sep 2006 14:53:16 +0000 (11:53 -0300)]
V4L/DVB (4635): Extend bttv and saa7134 to check for both AGP and PCI PCI failure case
We could go and work out if the target object is AGP or PCI but the
corner case of an Athlon 64 era box with PCI video is sufficiently
unusual it doesn't seem worth the extra work, at least until other cases
if any pop up.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Alan Cox [Thu, 14 Sep 2006 14:53:09 +0000 (11:53 -0300)]
V4L/DVB (4634): Zr36120: implement pcipci checks
Again depends on the PCIAGP_FAIL patch for a define. Someone with more
card knowledge should look at the ALIMAGIK case and whether latency can
be safely to set to 0xA or so.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should be doing this on all devices doing PCI<->PCI DMA. We only set
the _FAIL ones when the DMA will fail or may cause crashes. This relies
on the PCIAGP_FAIL patch I sent to Andrew already
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss [Thu, 14 Sep 2006 03:43:22 +0000 (00:43 -0300)]
V4L/DVB (4631): Av7110: remove V4L2_CAP_VBI_CAPTURE flag
Implement fix suggested by Michael Hunold for a bug reported
by Philipp Matthias Hahn: Starting "kdetv" on a Siemens DVB-C 1.x
produced an oops because kdetv opened "/dev/vbi0".
Remove the V4L2_CAP_VBI_CAPTURE flag because it does not work with
this type of hardware anyway.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vivi.current_norm field is not initialized in vivi.c, so a
VIDIOC_G_STD ioctl without a prior call to VIDIOC_S_STD gives
unpredictable results. mplayer does exactly this.
V4L/DVB (4624): Tvaudio: Replaced kernel_thread() with kthread_run()
Replaced kernel_thread() with kthread_run() since kernel_thread() is
deprecated in drivers/modules.
Removed the completion and the wait queue which are now useless with
kthread. Also removed the allow_signal() call as signals don't apply
to kernel threads.
Fixed a small race condition when thread is stopped.
Please check if the timer vs. thread still works fine without the wait
queue.
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4620): Fix AGC configuration for MOD3000P-based boards
While converting the configuration for the old DiB3000MC-module to the new one
a wrong AGC configuration was introduced.
This is using the old one again.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There seems to be an off by one error in the dibusb-mb.c which causes
the "Artec T1 with AN2235" box to be detected as a totally different
box - but it only happens if the Artec is one with the correct USB
IDs. A patch is attached to the second post. However, even with this
patch, the box still won't tune. It will tune using a 2.6.12 kernel
though.
Allan Third [Sun, 10 Sep 2006 15:05:50 +0000 (12:05 -0300)]
V4L/DVB (4616): [PATCH] Nebula DigiTV USB RC support
Attached is a patch against latest HG which adds remote control support
to the DigiTV driver. It works for me;
Signed-off-by: Allan Third <allan.third@gmail.com> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4613): Unmute/mute saa7134 when opening/closing the audio capture device.
This patch should enable unmuting the audio device when opening it (and
posterior muting when closing it), doing away with the need for unmute ioctls
or v4lctl usage.
V4L/DVB (4609): Improved i2c performance on software bitbang algoritm
Software I2C were using a very conservative value of udelay=16, meaning about
20Kbps. According with Philips I2C datasheet, the i2c should answer well for
times at the order of 4.7 us. So, using udelay=5 should work for all devices.
After this patch, the speed should be close to 66,67 Kbps, with the current
kernel software bitbang, with 30/60 duty cycle.
Anyway, added a new parameter (i2c_udelay) that would allow using conservative
values, if eventually a hardware doesn't support the datasheet values.
Thanks to Jean Delvare <khali@linux-fr.org> for pointing this improvement.
This driver was originally in budget-av.c, however I have extracted it into
a seperate file to permit reuse.
I also reworked the code to make it maintainable. I then examined the KNC1
windows drivers and rewrote the code in order to configure the PLL as they
do. This solves a lot of reported tuning problems.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bas Bloemsaat [Sun, 3 Sep 2006 12:47:41 +0000 (09:47 -0300)]
V4L/DVB (4599): Adds Compro PS39U USB ID to Vicam driver
Trivial patch to make Compro PS39U WebCam work with linux by using the
vicam driver.
The camera is just a vicam with another USB ID, so I added that ID to the
driver, and it works now.
Signed-off-by: Bas Bloemsaat <bas.bloemsaat@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sun, 3 Sep 2006 01:37:52 +0000 (22:37 -0300)]
V4L/DVB (4597): Improve resolution limit enforcements in pvrusb2
The pvrusb2 driver resolution limits are now programmed the following
way, based on empirical measurements of the hardware:
Vertical max: 480 for NTSC, 576 otherwise
Vertical min: 75 for 24xxx, 17 otherwise
Horizontal max: 720
Horizontal min: 720 for 24xxx, 19 otherwise
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sun, 3 Sep 2006 01:33:02 +0000 (22:33 -0300)]
V4L/DVB (4596): Fix saa7115 miscalculation that breaks NTSC
This repairs a problem introduced by a commit earlier applied. Thanks-to: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mike Isely [Sat, 2 Sep 2006 18:56:33 +0000 (15:56 -0300)]
V4L/DVB (4595): Remove CONFIG_VIDEO_PVRUSB2_24XXX from pvrusb2 driver
Support for 24xxx devices was previously explicitly bracketed with
CONFIG_VIDEO_PVRUSB2_24XXX inside the code because we didn't trust the
stability of these changes. We trust it now; so there's no reason to
leave this out of the driver anymore.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Scaling were not working fine;
Some reserved registers were wrong;
On some situations, saa7115 were not properly being initializated.
Removed some duplicated code. Thanks-to: Hans Verkuil <hverkuil@xs4all.nl> for co-working on this
patch.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Fri, 1 Sep 2006 21:36:48 +0000 (18:36 -0300)]
V4L/DVB (4585): VIDIOC_G_SLICED_VBI_CAP now accepts a v4l2_buf_type, make it IOWR
The VIDIOC_G_SLICED_VBI_CAP needs to receive the v4l2_buf_type field before
it can return a result. Hence this ioctl must be IOWR, not IOR. Since this
ioctl is still marked experimental we can make this change.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unai Uribarri [Mon, 28 Aug 2006 02:01:24 +0000 (23:01 -0300)]
V4L/DVB (4561): Sync'ing dvb-usb-remote with changes in USB input subsystem
This patch fixes the physical address and takes into account recent
changes in the USB input subsystem. Acked-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Unai Uribarri <unaiur@gmail.com> Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sun, 27 Aug 2006 22:22:15 +0000 (19:22 -0300)]
V4L/DVB (4548): Better temporal filter handling.
Adjust temporal filter if necessary. The problem with the temporal
filter is that it works well with full resolution capturing, but
not when the capture window is scaled (the filter introduces
a ghosting effect). So if the capture window changed, and there is
no updated filter value, then the filter is set depending on whether
the new window is full resolution or not.
For full resolution a setting of 8 really improves the video
quality, especially if the original video quality is suboptimal.
Also report VBI Format in VIDIOC_LOG_STATUS, it was missing.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sat, 26 Aug 2006 08:00:12 +0000 (05:00 -0300)]
V4L/DVB (4547): Add YUV HM12 and VBI IVTV format documentation.
README.hm12: documentation on the HM12 YUV format used by the cx23415/6 chip.
README.vbi: documentation on the V4L2_MPEG_STREAM_VBI_FMT_IVTV VBI format
used in MPEG streams.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Trent Piepho [Fri, 25 Aug 2006 01:43:45 +0000 (22:43 -0300)]
V4L/DVB (4533): Tda9887: add configuration setting for L standard PLL gating
Add a tuner config parameter for TDA9887, default_pll_gating_18, that
changes the L standard PLL gating value from 36% to 0% (datasheet says
0%, tda9887 code says 18%).
Turn this on for Microtune 4049FM5, as recomended by tuner datasheet.
Jochen Issing [Sat, 19 Aug 2006 19:03:21 +0000 (16:03 -0300)]
V4L/DVB (4528): PATCH: Club 3D zap250mini
After some structural changes, here comes the updated patch for the Club 3D
zap250mini USB dvb device.
Adding support for a WideView-based device with a different "COLD" ID.
V4L/DVB (4518): Allow manually selecting the proper helper drivers
There are several boards on V4L that can work with several different
helper modules for audio/video encoding/decoding and similar stuff.
This patch adds the capability of choicing between autoselecting the
pertinent helper modules for each driver, or to manually selecting
them. Acked-by: Michael Krufky <mkrufky@linuxtv.org> Acked-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4516): Split audio/video encoders/decoders from main drivers
Several audio/video encoders/decoders were just bound as if they were
part of the core driver.
In fact, they are generic enough to be used by other drivers as well,
since they use I2C event bus to communicate.
Several audio decoders were just bound as if they were part of
bttv driver. In fact, they are generic enough to be used by other
drivers as well, since they use I2C event bus to communicate.
Eric Sesterhenn [Mon, 21 Aug 2006 13:36:36 +0000 (10:36 -0300)]
V4L/DVB (4510): Fix signedness error in drivers/media/video/vivi.c
when checking the -Wextra signedness warnings issued by gcc 4.1
I came across this one:
drivers/media/video/vivi.c:1001: warning: comparison of unsigned expression < 0 is always false
Since videobuf_reqbufs() returns negative values on errors the current
code does no real error checking since gcc removes the comparison.
This patch fixes this issue by making ret a normal, signed integer.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several changes at register stuff were done since commit b45009b0288a96a3458f4f8e93cb776678d41875, but I've forgot
to add the copyright line for this. Those changes allowed
cx88 to have multiple tuners, allowing it to support hardware with
separated radio and video tuners. It also allows binding a tuner to an
specific i2c address.
The Coverity checker spotted the following two array overflows.
Registers 0xcc and 0xdc were cached on reg[] array, with only 128 elements,
instead of 256.
V4L/DVB (4504): Enable audio DMA restart on channel change even when cx88-alsa is compiled
cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
V4L/DVB (4501): Add support for knc one dvb-s plus with 1894:0011
Apparently there are two types of knc1 dvb-s plus cards with different tuners
(as for the knc1 dvb-s ones). This patch adds support for those cards with
subsystem id 1894:0011.
Successfully tested by: Benjamin Weber <benny1990@gmail.com>
Signed-off-by: Christoph Pfister <christophpfister@gmail.com> Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Thu, 10 Aug 2006 06:22:21 +0000 (03:22 -0300)]
V4L/DVB (4497): Reset USB part of DViCO Dual Digital during PCI driver attach
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Chris Pascoe [Thu, 10 Aug 2006 06:17:16 +0000 (03:17 -0300)]
V4L/DVB (4495): Fix "no data from ZL10353 based USB tuner" problem
Force parallel transport stream output on the ZL10353 attached to a
bluebird device.
Addresses the problem where a frontend lock was observed, but no MPEG
transport data was received.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dvb_frontend_detach() used invalid config option CONFIG_DVB_DETACH,
so dvb_frontend_detach() did not call symbol_put_addr().
Replaced CONFIG_DVB_DETACH by CONFIG_DVB_CORE_ATTACH.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Andrew Morton [Tue, 8 Aug 2006 13:52:22 +0000 (10:52 -0300)]
V4L/DVB (4484): Git-dvb: cadet build fix
drivers/media/radio/radio-cadet.c: In function 'cadet_do_ioctl':
drivers/media/radio/radio-cadet.c:362: warning: implicit declaration of function 'KERNEL_VERSION'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Dave Jones [Mon, 7 Aug 2006 16:18:56 +0000 (13:18 -0300)]
V4L/DVB (4480): Remove null chars from dvb names
DVB null terminates its device names, which seems odd, and should be
unnecessary. Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4479): LNB voltage control was inverted for the benefit of geniatech cards on Kworld
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Yeasah Pell <yeasah@schwide.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (4477): Improve hardware algorithm by setting the appropriate registers
Hardware algorithm needs to be configured to:
1) Increase timeout constants, to detect weaker signals;
2) do a wider zigzag search. Acked-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: Alastair Poole <netstar@gatheringofgray.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thomas Rokamp and others are reporting:
"I have now with success extracted a working firmware for the 93004 rev. C1A2."
This patch increments the firmware version to 2.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Flynn Marquardt found out that there is problem with the new dib3000mc-driver
when using with the real dib3000mc. It resulted in a segfault.
Fixed two things: use the correct I2C address and do not attach a tuner, when
the demod was previously failing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6-omap-h63xx.git / log