J. Bruce Fields [Sat, 20 Dec 2008 19:58:38 +0000 (11:58 -0800)]
nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT
Since nfsv4 allows LOCKT without an open, but the ->lock() method is a
file method, we fake up a struct file in the nfsv4 code with just the
fields we need initialized. But we forgot to initialize the file
operations, with the result that LOCKT never results in a call to the
filesystem's ->lock() method (if it exists).
We could just add that one more initialization. But this hack of faking
up a struct file with only some fields initialized seems the kind of
thing that might cause more problems in the future. We should either do
an open and get a real struct file, or make lock-testing an inode (not a
file) method.
This patch does the former.
Reported-by: Marc Eshel <eshel@almaden.ibm.com> Tested-by: Marc Eshel <eshel@almaden.ibm.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Trond Myklebust [Tue, 23 Dec 2008 21:30:11 +0000 (16:30 -0500)]
SUNRPC: Ensure the server closes sockets in a timely fashion
We want to ensure that connected sockets close down the connection when we
set XPT_CLOSE, so that we don't keep it hanging while cleaning up all the
stuff that is keeping a reference to the socket.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 11 Dec 2008 22:56:59 +0000 (17:56 -0500)]
lockd: Enable NLM use of AF_INET6
If the kernel is configured to support IPv6 and the RPC server can register
services via rpcbindv4, we are all set to enable IPv6 support for lockd.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: Aime Le Rouzic <aime.le-rouzic@bull.net> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 11 Dec 2008 22:56:52 +0000 (17:56 -0500)]
NLM: Rewrite IPv4 privileged requester's check
Clean up.
For consistency, rewrite the IPv4 check to match the same style as the
new IPv6 check. Note that ipv4_is_loopback() is somewhat broader in
its interpretation of what is a loopback address than simply
"127.0.0.1".
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Commit b85e4676 added the nlm_privileged_requester() helper to check
whether an RPC request was sent from a local privileged caller. It
recognizes IPv4 privileged callers (from "127.0.0.1"), and IPv6
privileged callers (from "::1").
However, IPV6_ADDR_LOOPBACK is not set for the mapped IPv4 loopback
address (::ffff:7f00:0001), so the test breaks when the kernel's RPC
service is IPv6-enabled but user space is calling via the IPv4
loopback address. This is actually the most common case for IPv6-
enabled RPC services on Linux.
Rewrite the IPv6 check to handle the mapped IPv4 loopback address as
well as a normal IPv6 loopback address.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 11 Dec 2008 22:56:07 +0000 (17:56 -0500)]
NSM: Replace IP address as our nlm_reboot lookup key
NLM provides file locking services for NFS files. Part of this service
includes a second protocol, known as NSM, which is a reboot
notification service. NLM uses this service to determine when to
reclaim locks or enter a grace period after a client or server reboots.
The NLM service (implemented by lockd in the Linux kernel) contacts
the local NSM service (implemented by rpc.statd in Linux user space)
via NSM protocol upcalls to register a callback when a particular
remote peer reboots.
To match the callback to the correct remote peer, the NLM service
constructs a cookie that it passes in the request. The NSM service
passes that cookie back to the NLM service when it is notified that
the given remote peer has indeed rebooted.
Currently on Linux, the cookie is the raw 32-bit IPv4 address of the
remote peer. To support IPv6 addresses, which are larger, we could
use all 16 bytes of the cookie to represent a full IPv6 address,
although we still can't represent an IPv6 address with a scope ID in
just 16 bytes.
Instead, to avoid the need for future changes to support additional
address types, we'll use a manufactured value for the cookie, and use
that to find the corresponding nsm_handle struct in the kernel during
the NLMPROC_SM_NOTIFY callback.
This should provide complete support in the kernel's NSM
implementation for IPv6 hosts, while remaining backwards compatible
with older rpc.statd implementations.
Note we also deal with another case where nsm_use_hostnames can change
while there are outstanding notifications, possibly resulting in the
loss of reboot notifications. After this patch, the priv cookie is
always used to lookup rebooted hosts in the kernel.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 11 Dec 2008 22:55:59 +0000 (17:55 -0500)]
NSM: More clean up of nsm_get_handle()
Clean up: refactor nsm_get_handle() so it is organized the same way that
nsm_reboot_lookup() is.
There is an additional micro-optimization here. This change moves the
"hostname & nsm_use_hostnames" test out of the list_for_each_entry()
clause in nsm_get_handle(), since it is loop-invariant.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:04:01 +0000 (19:04 -0500)]
NLM: Remove "create" argument from nsm_find()
Clean up: nsm_find() now has only one caller, and that caller
unconditionally sets the @create argument. Thus the @create
argument is no longer needed.
Since nsm_find() now has a more specific purpose, pick a more
appropriate name for it.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:03:54 +0000 (19:03 -0500)]
NLM: Call nsm_reboot_lookup() instead of nsm_find()
Invoke the newly introduced nsm_reboot_lookup() function in
nlm_host_rebooted() instead of nsm_find().
This introduces just one behavioral change: debugging messages
produced during reboot notification will now appear when the
NLMDBG_MONITOR flag is set, but not when the NLMDBG_HOSTCACHE flag
is set.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:03:39 +0000 (19:03 -0500)]
NLM: Decode "priv" argument of NLMPROC_SM_NOTIFY as an opaque
The NLM XDR decoders for the NLMPROC_SM_NOTIFY procedure should treat
their "priv" argument truly as an opaque, as defined by the protocol,
and let the upper layers figure out what is in it.
This will make it easier to modify the contents and interpretation of
the "priv" argument, and keep knowledge about what's in "priv" local
to fs/lockd/mon.c.
For now, the NLM and NSM implementations should behave exactly as they
did before.
The formation of the address of the rebooted host in
nlm_host_rebooted() may look a little strange, but it is the inverse
of how nsm_init_private() forms the private cookie. Plus, it's
going away soon anyway.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:03:31 +0000 (19:03 -0500)]
NLM: Change nlm_host_rebooted() to take a single nlm_reboot argument
Pass the nlm_reboot data structure directly from the NLMPROC_SM_NOTIFY
XDR decoders to nlm_host_rebooted(). This eliminates some packing and
unpacking of the NLMPROC_SM_NOTIFY results, and prepares for passing
these results, including the "priv" cookie, directly to a lookup
routine in fs/lockd/mon.c.
This patch changes code organization but should not cause any
behavioral change.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:03:16 +0000 (19:03 -0500)]
NSM: Generate NSMPROC_MON's "priv" argument when nsm_handle is created
Introduce a new data type, used by both the in-kernel NLM and NSM
implementations, that is used to manage the opaque "priv" argument
for the NSMPROC_MON and NLMPROC_SM_NOTIFY calls.
Construct the "priv" cookie when the nsm_handle is created.
The nsm_init_private() function may look a little strange, but it is
roughly equivalent to how the XDR encoder formed the "priv" argument.
It's going to go away soon.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:02:53 +0000 (19:02 -0500)]
NSM: Add dprintk() calls in nsm_find and nsm_release
Introduce some dprintk() calls in fs/lockd/mon.c that are enabled by
the NLMDBG_MONITOR flag. These report when we find, create, and
release nsm_handles.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:02:45 +0000 (19:02 -0500)]
NSM: Move nsm_find() to fs/lockd/mon.c
The nsm_find() function sets up fresh nsm_handle entries. This is
where we will store the "priv" cookie used to lookup nsm_handles during
reboot recovery. The cookie will be constructed when nsm_find()
creates a new nsm_handle.
As much as possible, I would like to keep everything that handles a
"priv" cookie in fs/lockd/mon.c so that all the smarts are in one
source file. That organization should make it pretty simple to see how
all this works.
To me, it makes more sense than the current arrangement to keep
nsm_find() with nsm_monitor() and nsm_unmonitor().
So, start reorganizing by moving nsm_find() into fs/lockd/mon.c. The
nsm_release() function comes along too, since it shares the nsm_lock
global variable.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Sat, 6 Dec 2008 00:02:07 +0000 (19:02 -0500)]
NSM: Move NSM program and procedure numbers to fs/lockd/mon.c
Clean up: Move the RPC program and procedure numbers for NSM into the
one source file that needs them: fs/lockd/mon.c.
And, as with NLM, NFS, and rpcbind calls, use NSMPROC_FOO instead of
SM_FOO for NSM procedure numbers.
Finally, make a couple of comments more precise: what is referred to
here as SM_NOTIFY is really the NLM (lockd) NLMPROC_SM_NOTIFY downcall,
not NSMPROC_NOTIFY.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:46 +0000 (14:21 -0500)]
NSM: Check result of SM_UNMON upcall
Make sure any error returned by rpc.statd during an SM_UNMON call is
reported rather than ignored completely. There isn't much to do with
such an error, but we should log it in any case.
Similar to a recent change to nsm_monitor().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:31 +0000 (14:21 -0500)]
NSM: Release nsmhandle in nlm_destroy_host
The nsm_handle's reference count is bumped in nlm_lookup_host(). It
should be decremented in nlm_destroy_host() to make it easier to see
the balance of these two operations.
Move the nsm_release() call to fs/lockd/host.c.
The h_nsmhandle pointer is set in nlm_lookup_host(), and never cleared.
The nlm_destroy_host() function is never called for the same nlm_host
twice, so h_nsmhandle won't ever be NULL when nsm_unmonitor() is
called.
All references to the nlm_host are gone before it is freed. We can
skip making h_nsmhandle NULL just before the nlm_host is deallocated.
It's also likely we can remove the h_nsmhandle NULL check in
nlmsvc_is_client() as well, but we can do that later when rearchitect-
ing the nlm_host cache.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:24 +0000 (14:21 -0500)]
NLM: Move the public declaration of nsm_monitor() to lockd.h
Clean up.
Make the nlm_host argument "const," and move the public declaration to
lockd.h with other NSM public function (nsm_release, eg) and global
variable declarations.
Add a documenting comment.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:15 +0000 (14:21 -0500)]
NSM: Make sure to return an error if the SM_MON call result is not zero
The nsm_monitor() function reports an error and does not set sm_monitored
if the SM_MON upcall reply has a non-zero result code, but nsm_monitor()
does not return an error to its caller in this case.
Since sm_monitored is not set, the upcall is retried when the next NLM
request invokes nsm_monitor(). However, that may not come for a while.
In the meantime, at least one NLM request will potentially proceed
without the peer being monitored properly.
Have nsm_monitor() return an error if the result code is non-zero.
This will cause all NLM requests to fail immediately if the upcall
completed successfully but rpc.statd returned an error.
This may be inconvenient in some cases (for example if rpc.statd
cannot complete a proper DNS reverse lookup of the hostname), but will
make the reboot monitoring service more robust by forcing such issues
to be corrected by an admin.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:08 +0000 (14:21 -0500)]
NSM: Remove BUG_ON() in nsm_monitor()
Clean up: Remove the BUG_ON() invocation in nsm_monitor(). It's not
likely that nsm_monitor() is ever called with a NULL host pointer, and
the code will die anyway if host is NULL.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:21:01 +0000 (14:21 -0500)]
NLM: Remove redundant printk() in nlmclnt_lock()
The nsm_monitor() function already generates a printk(KERN_NOTICE) if
the SM_MON upcall fails, so the similar printk() in the nlmclnt_lock()
function is redundant.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:20:46 +0000 (14:20 -0500)]
NSM: Support IPv6 version of mon_name
The "mon_name" argument of the NSMPROC_MON and NSMPROC_UNMON upcalls
is a string that contains the hostname or IP address of the remote peer
to be notified when this host has rebooted. The sm-notify command uses
this identifier to contact the peer when we reboot, so it must be
either a well-qualified DNS hostname or a presentation format IP
address string.
When the "nsm_use_hostnames" sysctl is set to zero, the kernel's NSM
provides a presentation format IP address in the "mon_name" argument.
Otherwise, the "caller_name" argument from NLM requests is used,
which is usually just the DNS hostname of the peer.
To support IPv6 addresses for the mon_name argument, we use the
nsm_handle's address eye-catcher, which already contains an appropriate
presentation format address string. Using the eye-catcher string
obviates the need to use a large buffer on the stack to form the
presentation address string for the upcall.
This patch also addresses a subtle bug.
An NSMPROC_MON request and the subsequent NSMPROC_UNMON request for the
same peer are required to use the same value for the "mon_name"
argument. Otherwise, rpc.statd's NSMPROC_UNMON processing cannot
locate the database entry for that peer and remove it.
If the setting of nsm_use_hostnames is changed between the time the
kernel sends an NSMPROC_MON request and the time it sends the
NSMPROC_UNMON request for the same peer, the "mon_name" argument for
these two requests may not be the same. This is because the value of
"mon_name" is currently chosen at the moment the call is made based on
the setting of nsm_use_hostnames
To ensure both requests pass identical contents in the "mon_name"
argument, we now select which string to use for the argument in the
nsm_monitor() function. A pointer to this string is saved in the
nsm_handle so it can be used for a subsequent NSMPROC_UNMON upcall.
NB: There are other potential problems, such as how nlm_host_rebooted()
might behave if nsm_use_hostnames were changed while hosts are still
being monitored. This patch does not attempt to address those
problems.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:20:38 +0000 (14:20 -0500)]
NSM: Use modern style for sm_name field in nsm_handle
Clean up: I'm about to add another "char *" field to the nsm_handle
structure. The sm_name field uses an older style of declaring a
"char *" field. If I match that style for the new field, checkpatch.pl
will complain.
So, fix the sm_name field to use the new style.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:20:08 +0000 (14:20 -0500)]
NLM: Support IPv6 scope IDs in nlm_display_address()
Scope ID support is needed since the kernel's NSM implementation is
about to use these displayed addresses as a mon_name in some cases.
When nsm_use_hostnames is zero, without scope ID support NSM will fail
to handle peers that contact us via a link-local address. Link-local
addresses do not work without an interface ID, which is stored in the
sockaddr's sin6_scope_id field.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:19:53 +0000 (14:19 -0500)]
NLM: Remove address eye-catcher buffers from nlm_host
The h_name field in struct nlm_host is a just copy of
h_nsmhandle->sm_name. Likewise, the contents of the h_addrbuf field
should be identical to the sm_addrbuf field.
The h_srcaddrbuf field is used only in one place for debugging. We can
live without this until we get %pI formatting for printk().
Currently these buffers are 48 bytes, but we need to support scope IDs
in IPv6 presentation addresses, which means making the buffers even
larger. Instead, let's find ways to eliminate them to save space.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Chuck Lever [Thu, 4 Dec 2008 19:19:45 +0000 (14:19 -0500)]
NLM: Use modern style for pointer fields in nlm_host
Clean up: I'm about to add another "char *" field to the nlm_host
structure. The h_name field, for example, uses an older style of
declaring a "char *" field. If I match that style for the new field,
checkpatch.pl will complain.
So, fix pointer fields to use the new style.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Jeff Layton [Mon, 20 Oct 2008 15:51:58 +0000 (11:51 -0400)]
lockd: set svc_serv->sv_maxconn to a more reasonable value (try #3)
The default method for calculating the number of connections allowed
per RPC service arbitrarily limits single-threaded services to 80
connections. This is too low for services like lockd and artificially
limits the number of TCP clients that it can support.
Have lockd set a default sv_maxconn value to 1024 (which is the typical
default value for RLIMIT_NOFILE. Also add a module parameter to allow an
admin to set this to an arbitrary value.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Neil Brown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Jeff Layton [Mon, 20 Oct 2008 15:51:57 +0000 (11:51 -0400)]
sunrpc: add sv_maxconn field to svc_serv (try #3)
svc_check_conn_limits() attempts to prevent denial of service attacks
by having the service close old connections once it reaches a
threshold. This threshold is based on the number of threads in the
service:
(serv->sv_nrthreads + 3) * 20
Once we reach this, we drop the oldest connections and a printk pops
to warn the admin that they should increase the number of threads.
Increasing the number of threads isn't an option however for services
like lockd. We don't want to eliminate this check entirely for such
services but we need some way to increase this limit.
This patch adds a sv_maxconn field to the svc_serv struct. When it's
set to 0, we use the current method to calculate the max number of
connections. RPC services can then set this on an as-needed basis.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Acked-by: Neil Brown <neilb@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Supply dm_add_exception as a callback to the read_metadata function.
Add a status function ready for a later patch and name the functions
consistently.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm snapshot: split out exception store implementations
Move the existing snapshot exception store implementations out into
separate files. Later patches will place these behind a new
interface in preparation for alternative implementations.
dm snapshot: separate out exception store interface
Pull structures that bridge the gap between snapshot and
exception store out of dm-snap.h and put them in a new
.h file - dm-exception-store.h. This file will define the
API for new exception stores.
Ultimately, dm-snap.h is unnecessary, since only dm-snap.c
should be using it.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The same workqueue is used both for sending uevents and processing queued I/O.
Deadlock has been reported in RHEL5 when sending a uevent was blocked waiting
for the queued I/O to be processed. Use scheduled_work() for the asynchronous
uevents instead.
Milan Broz [Tue, 6 Jan 2009 03:05:12 +0000 (03:05 +0000)]
dm: add name and uuid to sysfs
Implement simple read-only sysfs entry for device-mapper block device.
This patch adds a simple sysfs directory named "dm" under block device
properties and implements
- name attribute (string containing mapped device name)
- uuid attribute (string containing UUID, or empty string if not set)
The kobject is embedded in mapped_device struct, so no additional
memory allocation is needed for initializing sysfs entry.
During the processing of sysfs attribute we need to lock mapped device
which is done by a new function dm_get_from_kobj, which returns the md
associated with kobject and increases the usage count.
Each 'show attribute' function is responsible for its own locking.
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Tue, 6 Jan 2009 03:05:10 +0000 (03:05 +0000)]
dm table: rework reference counting
Rework table reference counting.
The existing code uses a reference counter. When the last reference is
dropped and the counter reaches zero, the table destructor is called.
Table reference counters are acquired/released from upcalls from other
kernel code (dm_any_congested, dm_merge_bvec, dm_unplug_all).
If the reference counter reaches zero in one of the upcalls, the table
destructor is called from almost random kernel code.
This leads to various problems:
* dm_any_congested being called under a spinlock, which calls the
destructor, which calls some sleeping function.
* the destructor attempting to take a lock that is already taken by the
same process.
* stale reference from some other kernel code keeps the table
constructed, which keeps some devices open, even after successful
return from "dmsetup remove". This can confuse lvm and prevent closing
of underlying devices or reusing device minor numbers.
The patch changes reference counting so that the table destructor can be
called only at predetermined places.
The table has always exactly one reference from either mapped_device->map
or hash_cell->new_map. After this patch, this reference is not counted
in table->holders. A pair of dm_create_table/dm_destroy_table functions
is used for table creation/destruction.
Temporary references from the other code increase table->holders. A pair
of dm_table_get/dm_table_put functions is used to manipulate it.
When the table is about to be destroyed, we wait for table->holders to
reach 0. Then, we call the table destructor. We use active waiting with
msleep(1), because the situation happens rarely (to one user in 5 years)
and removing the device isn't performance-critical task: the user doesn't
care if it takes one tick more or not.
This way, the destructor is called only at specific points
(dm_table_destroy function) and the above problems associated with lazy
destruction can't happen.
Finally remove the temporary protection added to dm_any_congested().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Andi Kleen [Tue, 6 Jan 2009 03:05:09 +0000 (03:05 +0000)]
dm: support barriers on simple devices
Implement barrier support for single device DM devices
This patch implements barrier support in DM for the common case of dm linear
just remapping a single underlying device. In this case we can safely
pass the barrier through because there can be no reordering between
devices.
NB. Any DM device might cease to support barriers if it gets
reconfigured so code must continue to allow for a possible
-EOPNOTSUPP on every barrier bio submitted. - agk
Kiyoshi Ueda [Tue, 6 Jan 2009 03:05:07 +0000 (03:05 +0000)]
dm request: extend target interface
This patch adds the following target interfaces for request-based dm.
map_rq : for mapping a request
rq_end_io : for finishing a request
busy : for avoiding performance regression from bio-based dm.
Target can tell dm core not to map requests now, and
that may help requests in the block layer queue to be
bigger by I/O merging.
In bio-based dm, this behavior is done by device
drivers managing the block layer queue.
But in request-based dm, dm core has to do that
since dm core manages the block layer queue.
Takahiro Yasui [Tue, 6 Jan 2009 03:04:59 +0000 (03:04 +0000)]
dm log: avoid reinitialising io_req on every operation
rw_header function updates three members of io_req data every time
when I/O is processed. bi_rw and notify.fn are never modified once
they get initialized, and so they can be set in advance.
header_to_disk() can also be pulled out of write_header() since only one
caller needs it and write_header() can be replaced by rw_header()
directly.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change dm_unregister_target to return void and use BUG() for error
reporting.
dm_unregister_target can only fail because of programming bug in the
target driver. It can't fail because of user's behavior or disk errors.
This patch changes unregister_target to return void and use BUG if
someone tries to unregister non-registered target or unregister target
that is in use.
This patch removes code duplication (testing of error codes in all dm
targets) and reports bugs in just one place, in dm_unregister_target. In
some target drivers, these return codes were ignored, which could lead
to a situation where bugs could be missed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always increase the error count when I/O on a leg of a mirror fails.
The error count is used to decide whether to select an alternative
mirror leg. If the target doesn't use the "handle_errors" feature, the
error count is not updated and the bio can get requeued forever by the
read callback.
Fix it by increasing error_count before the handle_errors feature
checking.
Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Takahiro Yasui [Tue, 6 Jan 2009 03:04:56 +0000 (03:04 +0000)]
dm log: fix dm_io_client leak on error paths
In create_log_context function, dm_io_client_destroy function needs
to be called, when memory allocation of disk_header, sync_bits and
recovering_bits failed, but dm_io_client_destroy is not called.
Cc: stable@kernel.org Signed-off-by: Takahiro Yasui <tyasui@redhat.com> Acked-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Tue, 6 Jan 2009 03:04:54 +0000 (03:04 +0000)]
dm snapshot: change yield to msleep
Change yield() to msleep(1). If the thread had realtime priority,
yield() doesn't really yield, so the yielding process would loop
indefinitely and cause machine lockup.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Tue, 6 Jan 2009 03:04:53 +0000 (03:04 +0000)]
dm table: drop reference at unbind
Move one dm_table_put() so that the last reference in the thread
gets dropped in __unbind().
This is required for a following patch,
dm-table-rework-reference-counting.patch, which will change the logic in
such a way that table destructor is called only at specific points in
the code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: convert to stop_machine_create/destroy.
stop_machine: introduce stop_machine_create/destroy.
parisc: fix module loading failure of large kernel modules
module: fix module loading failure of large kernel modules for parisc
module: fix warning of unused function when !CONFIG_PROC_FS
kernel/module.c: compare symbol values when marking symbols as exported in /proc/kallsyms.
remove CONFIG_KMOD
Linus Torvalds [Tue, 6 Jan 2009 03:03:11 +0000 (19:03 -0800)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
swiotlb: Don't include linux/swiotlb.h twice in lib/swiotlb.c
intel-iommu: fix build error with INTR_REMAP=y and DMAR=n
swiotlb: add missing __init annotations
Linus Torvalds [Tue, 6 Jan 2009 02:58:06 +0000 (18:58 -0800)]
Merge branch 'i2c-next' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-next' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-omap: fix type of irq handler function
i2c-s3c2410: Change IRQ to be plain integer.
i2c-s3c2410: Allow more than one i2c-s3c2410 adapter
i2c-s3c2410: Remove default platform data.
i2c-s3c2410: Use platform data for gpio configuration
i2c-s3c2410: Fixup style problems from checkpatch.pl
i2c-omap: Enable I2C wakeups for 34xx
i2c-omap: reprogram OCP_SYSCONFIG register after reset
i2c-omap: convert 'rev1' flag to generic 'rev' u8
i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un,}idle()
i2c-omap: Clean-up i2c-omap
i2c-omap: Don't compile in OMAP15xx I2C ISR for non-OMAP15xx builds
i2c-omap: Mark init-only functions as __init
i2c-omap: Add support for omap34xx
i2c-omap: FIFO handling support and broken hw workaround for i2c-omap
i2c-omap: Add high-speed support to omap-i2c
i2c-omap: Close suspected race between omap_i2c_idle() and omap_i2c_isr()
i2c-omap: Do not use interruptible wait call in omap_i2c_xfer_msg
Fix up apparently-trivial conflict in drivers/i2c/busses/i2c-s3c2410.c
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (27 commits)
GFS2: Use DEFINE_SPINLOCK
GFS2: Fix use-after-free bug on umount (try #2)
Revert "GFS2: Fix use-after-free bug on umount"
GFS2: Streamline alloc calculations for writes
GFS2: Send useful information with uevent messages
GFS2: Fix use-after-free bug on umount
GFS2: Remove ancient, unused code
GFS2: Move four functions from super.c
GFS2: Fix bug in gfs2_lock_fs_check_clean()
GFS2: Send some sensible sysfs stuff
GFS2: Kill two daemons with one patch
GFS2: Move gfs2_recoverd into recovery.c
GFS2: Fix "truncate in progress" hang
GFS2: Clean up & move gfs2_quotad
GFS2: Add more detail to debugfs glock dumps
GFS2: Banish struct gfs2_rgrpd_host
GFS2: Move rg_free from gfs2_rgrpd_host to gfs2_rgrpd
GFS2: Move rg_igeneration into struct gfs2_rgrpd
GFS2: Banish struct gfs2_dinode_host
GFS2: Move i_size from gfs2_dinode_host and rename it to i_disksize
...
Linus Torvalds [Tue, 6 Jan 2009 02:47:12 +0000 (18:47 -0800)]
igb: fix anoying type mismatch warning on rx/tx queue sizing
When using "min()", the types of both sides should match. With the cpu
mask changes, the type of num_online_cpus() will now depend on config
options. Use "min_t()" with an explicit type instead.
And make the rx/tx case look the same too, just for sanity.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
qlge: Fix sparse warnings for tx ring indexes.
qlge: Fix sparse warning regarding rx buffer queues.
qlge: Fix sparse endian warning in ql_hw_csum_setup().
qlge: Fix sparse endian warning for inbound packet control block flags.
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
myri10ge: print MAC and serial number on probe failure
pkt_sched: cls_u32: Fix locking in u32_change()
iucv: fix cpu hotplug
af_iucv: Free iucv path/socket in path_pending callback
af_iucv: avoid left over IUCV connections from failing connects
af_iucv: New error return codes for connect()
net/ehea: bitops work on unsigned longs
Revert "net: Fix for initial link state in 2.6.28"
tcp: Kill extraneous SPLICE_F_NONBLOCK checks.
tcp: don't mask EOF and socket errors on nonblocking splice receive
dccp: Integrate the TFRC library with DCCP
dccp: Clean up ccid.c after integration of CCID plugins
dccp: Lockless integration of CCID congestion-control plugins
qeth: get rid of extra argument after printk to dev_* conversion
qeth: No large send using EDDP for HiperSockets.
...
Linus Torvalds [Tue, 6 Jan 2009 02:34:12 +0000 (18:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - Fix a typo in IEC958 PCM name
ASoC: fix davinci-sffsdr buglet
ALSA: sound/usb: Use negated usb_endpoint_xfer_control, etc
ALSA: hda - cxt5051 report jack state
ALSA: hda - add basic jack reporting functions to patch_conexant.c
ALSA: Use usb_set/get_intfdata
ASoC: Clean up kerneldoc warnings
ASoC: Fix pxa2xx-pcm checks for invalid DMA channels
LSA: hda - Add HP Acacia detection
ALSA: hda - fix name for ALC1200
ALSA: sound/usb: use USB API functions rather than constants
ASoC: TWL4030: DAPM based capture implementation
ASoC: TWL4030: Make the enum filter generic for twl4030
Linus Torvalds [Tue, 6 Jan 2009 02:33:38 +0000 (18:33 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix on resume, now preserves user policy min/max.
[CPUFREQ] Add Celeron Core support to p4-clockmod.
[CPUFREQ] add to speedstep-lib additional fsb values for core processors
[CPUFREQ] Disable sysfs ui for p4-clockmod.
[CPUFREQ] p4-clockmod: reduce noise
[CPUFREQ] clean up speedstep-centrino and reduce cpumask_t usage
Linus Torvalds [Tue, 6 Jan 2009 02:32:43 +0000 (18:32 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (138 commits)
ocfs2: Access the right buffer_head in ocfs2_merge_rec_left.
ocfs2: use min_t in ocfs2_quota_read()
ocfs2: remove unneeded lvb casts
ocfs2: Add xattr support checking in init_security
ocfs2: alloc xattr bucket in ocfs2_xattr_set_handle
ocfs2: calculate and reserve credits for xattr value in mknod
ocfs2/xattr: fix credits calculation during index create
ocfs2/xattr: Always updating ctime during xattr set.
ocfs2/xattr: Remove extend_trans call and add its credits from the beginning
ocfs2/dlm: Fix race during lockres mastery
ocfs2/dlm: Fix race in adding/removing lockres' to/from the tracking list
ocfs2/dlm: Hold off sending lockres drop ref message while lockres is migrating
ocfs2/dlm: Clean up errors in dlm_proxy_ast_handler()
ocfs2/dlm: Fix a race between migrate request and exit domain
ocfs2: One more hamming code optimization.
ocfs2: Another hamming code optimization.
ocfs2: Don't hand-code xor in ocfs2_hamming_encode().
ocfs2: Enable metadata checksums.
ocfs2: Validate superblock with checksum and ecc.
ocfs2: Checksum and ECC for directory blocks.
...
Linus Torvalds [Tue, 6 Jan 2009 02:32:06 +0000 (18:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
inotify: fix type errors in interfaces
fix breakage in reiserfs_new_inode()
fix the treatment of jfs special inodes
vfs: remove duplicate code in get_fs_type()
add a vfs_fsync helper
sys_execve and sys_uselib do not call into fsnotify
zero i_uid/i_gid on inode allocation
inode->i_op is never NULL
ntfs: don't NULL i_op
isofs check for NULL ->i_op in root directory is dead code
affs: do not zero ->i_op
kill suid bit only for regular files
vfs: lseek(fd, 0, SEEK_CUR) race condition
Nick Piggin [Tue, 6 Jan 2009 02:05:50 +0000 (03:05 +0100)]
mm lockless pagecache barrier fix
An XFS workload showed up a bug in the lockless pagecache patch. Basically it
would go into an "infinite" loop, although it would sometimes be able to break
out of the loop! The reason is a missing compiler barrier in the "increment
reference count unless it was zero" case of the lockless pagecache protocol in
the gang lookup functions.
This would cause the compiler to use a cached value of struct page pointer to
retry the operation with, rather than reload it. So the page might have been
removed from pagecache and freed (refcount==0) but the lookup would not correctly
notice the page is no longer in pagecache, and keep attempting to increment the
refcount and failing, until the page gets reallocated for something else. This
isn't a data corruption because the condition will be detected if the page has
been reallocated. However it can result in a lockup.
Linus points out that ACCESS_ONCE is also required in that pointer load, even
if it's absence is not causing a bug on our particular build. The most general
way to solve this is just to put an rcu_dereference in radix_tree_deref_slot.
Assembly of find_get_pages,
before:
.L220:
movq (%rbx), %rax #* ivtmp.1162, tmp82
movq (%rax), %rdi #, prephitmp.1149
.L218:
testb $1, %dil #, prephitmp.1149
jne .L217 #,
testq %rdi, %rdi # prephitmp.1149
je .L203 #,
cmpq $-1, %rdi #, prephitmp.1149
je .L217 #,
movl 8(%rdi), %esi # <variable>._count.counter, c
testl %esi, %esi # c
je .L218 #,
after:
.L212:
movq (%rbx), %rax #* ivtmp.1109, tmp81
movq (%rax), %rdi #, ret
testb $1, %dil #, ret
jne .L211 #,
testq %rdi, %rdi # ret
je .L197 #,
cmpq $-1, %rdi #, ret
je .L211 #,
movl 8(%rdi), %esi # <variable>._count.counter, c
testl %esi, %esi # c
je .L212 #,
(notice the obvious infinite loop in the first example, if page->count remains 0)
Signed-off-by: Nick Piggin <npiggin@suse.de> Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ron Mercer [Tue, 6 Jan 2009 02:19:59 +0000 (18:19 -0800)]
qlge: Fix sparse warnings for tx ring indexes.
Warnings:
drivers/net/qlge/qlge_main.c:1474:34: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1475:36: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1592:51: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1941:20: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1941:20: expected restricted unsigned int [usertype] tid
drivers/net/qlge/qlge_main.c:1941:20: got int [signed] index
drivers/net/qlge/qlge_main.c:1945:24: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1945:24: expected restricted unsigned int [usertype] txq_idx
drivers/net/qlge/qlge_main.c:1945:24: got unsigned int [unsigned] [usertype] tx_ring_idx
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Warnings:
drivers/net/qlge/qlge_main.c:909:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:909:17: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:909:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:911:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:911:17: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:911:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:974:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:974:17: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:974:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:975:17: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:975:17: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:975:17: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2132:16: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2132:16: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:2132:16: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2133:16: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2133:16: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:2133:16: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2212:15: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2212:15: expected unsigned int [unsigned] [usertype] addr_lo
drivers/net/qlge/qlge_main.c:2212:15: got restricted unsigned int [usertype] <noident>
drivers/net/qlge/qlge_main.c:2214:15: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:2214:15: expected unsigned int [unsigned] [usertype] addr_hi
drivers/net/qlge/qlge_main.c:2214:15: got restricted unsigned int [usertype] <noident>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Tue, 6 Jan 2009 02:18:45 +0000 (18:18 -0800)]
qlge: Fix sparse endian warning in ql_hw_csum_setup().
Changed u16 to __sum16 usage.
Warnings:
drivers/net/qlge/qlge_main.c:1897:9: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1897:9: expected unsigned short [usertype] *check
drivers/net/qlge/qlge_main.c:1897:9: got restricted unsigned short *<noident>
drivers/net/qlge/qlge_main.c:1903:9: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1903:9: expected unsigned short [usertype] *check
drivers/net/qlge/qlge_main.c:1903:9: got restricted unsigned short *<noident>
drivers/net/qlge/qlge_main.c:1909:9: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_main.c:1909:9: expected unsigned short [unsigned] [short] [usertype] <noident>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Tue, 6 Jan 2009 02:18:22 +0000 (18:18 -0800)]
qlge: Fix sparse endian warning for inbound packet control block flags.
Changed flags element from __le32 to 3 reserved bytes and one byte of
flags. Changed flags bit definitions to reflect byte width instead of
__le32 width.
Warnings:
drivers/net/qlge/qlge_main.c:1206:16: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1207:16: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1233:17: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1276:17: warning: restricted degrades to integer
drivers/net/qlge/qlge_main.c:1349:19: warning: restricted degrades to integer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Tue, 6 Jan 2009 02:17:33 +0000 (18:17 -0800)]
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
drivers/net/qlge/qlge_ethtool.c:59:23: warning: cast to restricted type
drivers/net/qlge/qlge_ethtool.c:59:21: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_ethtool.c:59:21: expected restricted unsigned short [usertype] irq_delay
drivers/net/qlge/qlge_ethtool.c:59:21: got unsigned short [unsigned] [usertype] <noident>
drivers/net/qlge/qlge_ethtool.c:61:8: warning: cast to restricted type
drivers/net/qlge/qlge_ethtool.c:60:21: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_ethtool.c:60:21: expected restricted unsigned short [usertype] pkt_delay
drivers/net/qlge/qlge_ethtool.c:60:21: got unsigned short [unsigned] [usertype] <noident>
drivers/net/qlge/qlge_ethtool.c:82:23: warning: cast to restricted type
drivers/net/qlge/qlge_ethtool.c:82:21: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_ethtool.c:82:21: expected restricted unsigned short [usertype] irq_delay
drivers/net/qlge/qlge_ethtool.c:82:21: got unsigned short [unsigned] [usertype] <noident>
drivers/net/qlge/qlge_ethtool.c:84:8: warning: cast to restricted type
drivers/net/qlge/qlge_ethtool.c:83:21: warning: incorrect type in assignment (different base types)
drivers/net/qlge/qlge_ethtool.c:83:21: expected restricted unsigned short [usertype] pkt_delay
drivers/net/qlge/qlge_ethtool.c:83:21: got unsigned short [unsigned] [usertype] <noident>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jarek Poplawski [Tue, 6 Jan 2009 02:14:19 +0000 (18:14 -0800)]
pkt_sched: cls_u32: Fix locking in u32_change()
New nodes are inserted in u32_change() under rtnl_lock() with wmb(),
so without tcf_tree_lock() like in other classifiers (e.g. cls_fw).
This isn't enough without rmb() on the read side, but on the other
hand adding such barriers doesn't give any savings, so the lock is
added instead.
Reported-by: m0sia <m0sia@plotinka.ru> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Calaby [Tue, 6 Jan 2009 02:13:49 +0000 (18:13 -0800)]
sparc: Fix minor SPARC32 compile error
When CONFIG_PROC_FS is unset, include/linux/interrupt.h defines
init_irq_proc() as an empty function.
arch/sparc/kernel/irq_32.c defines this function unconditionally.
Fix the latter so that it only defines this function when CONFIG_PROC_FS
is set.
This fixes the following error:
arch/sparc/kernel/irq_32.c:672: error: redefinition of 'init_irq_proc'
include/linux/interrupt.h:461: error: previous definition of
'init_irq_proc' was here
This was found using randconfig builds.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Tue, 6 Jan 2009 02:09:02 +0000 (18:09 -0800)]
iucv: fix cpu hotplug
If the iucv module is compiled in/loaded but no user is registered cpu
hot remove doesn't work. Reason for that is that the iucv cpu hotplug
notifier on CPU_DOWN_PREPARE checks if the iucv_buffer_cpumask would
be empty after the corresponding bit would be cleared. However the bit
was never set since iucv wasn't enable. That causes all cpu hot unplug
operations to fail in this scenario.
To fix this use iucv_path_table as an indicator wether iucv is enabled
or not.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_iucv: Free iucv path/socket in path_pending callback
Free iucv path after iucv_path_sever() calls in iucv_callback_connreq()
(path_pending() iucv callback).
If iucv_path_accept() fails, free path and free/kill newly created socket.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log