Michael Chan [Fri, 2 May 2008 23:57:59 +0000 (16:57 -0700)]
bnx2: Update RV2P firmware for 5709.
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:26 +0000 (16:57 -0700)]
bnx2: Zero out context memory for 5709.
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:44 +0000 (16:56 -0700)]
bnx2: Fix remote PHY initial link state.
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:16 +0000 (16:56 -0700)]
bnx2: Refine remote PHY locking.
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: forwarding table information for >256 devices
The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:
brctl showmacs
The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:50 +0000 (16:49 -0700)]
tg3: Update version to 3.92
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:29 +0000 (16:49 -0700)]
tg3: Add link state reporting to UMP firmware
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:48:59 +0000 (16:48 -0700)]
tg3: Fix ethtool loopback test for 5761 BX devices
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:48:36 +0000 (16:48 -0700)]
tg3: Fix 5761 NVRAM sizes
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:47:53 +0000 (16:47 -0700)]
tg3: Use constant 500KHz MI clock on adapters with a CPMU
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Machek [Fri, 2 May 2008 23:45:10 +0000 (16:45 -0700)]
hci_usb.h: fix hard-to-trigger race
If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking. Prevent that from happening
by strategically placed barriers.
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Fri, 2 May 2008 23:44:07 +0000 (16:44 -0700)]
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
Makes the intention of the nested min/max clear.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Travis [Fri, 2 May 2008 23:43:08 +0000 (16:43 -0700)]
net: remove NR_CPUS arrays in net/core/dev.c
Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Fri, 2 May 2008 23:25:46 +0000 (16:25 -0700)]
bluetooth: use get/put_unaligned_* helpers
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Add a WARN_ON_ONCE() to the transmit timeout function
WARN_ON_ONCE() gives a stack trace including the full module list.
Having this in the kernel dump for the timeout case in the
generic netdev watchdog will help us see quicker which driver
is involved. It also allows us to collect statistics
and patterns in terms of which drivers have this event occuring.
Suggested by Andrew Morton
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 2 May 2008 23:20:10 +0000 (16:20 -0700)]
net: Add missing braces to multi-statement if()s
One finds all kinds of crazy things with some shell pipelining.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 2 May 2008 11:12:41 +0000 (04:12 -0700)]
netns: assign PDE->data before gluing entry into /proc tree
In this unfortunate case, proc_mkdir_mode wrapper can't be used anymore and
this is no way to reuse proc_create_data due to nlinks assignment. So,
copy the code from proc_mkdir and assign PDE->data at the appropriate
moment.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 2 May 2008 09:46:22 +0000 (02:46 -0700)]
net: assign PDE->data before gluing PDE into /proc tree
Simply replace proc_create and further data assigned with proc_create_data.
Additionally, there is no need to assign NULL to PDE->data after creation,
/proc generic has already done this for us.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Mon, 21 Apr 2008 17:01:09 +0000 (19:01 +0200)]
rt2x00: Fix quality/activity led handling
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bill Moss [Thu, 17 Apr 2008 23:03:40 +0000 (16:03 -0700)]
iwlwifi: fix debug messages during scanning
direct_mask will be set when we are not associated and requesting a
direct scan. The second debug print will be confusing as priv->essid
is not set at that time and it will thus print "<hidden>" while it is
known to which AP a direct scan is requested - as previous debug message
also indicates.
Now make all debugging consistent.
Signed-off-by: Bill Moss <bmoss@clemson.edu> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Guy Cohen [Mon, 21 Apr 2008 22:41:57 +0000 (15:41 -0700)]
iwlwifi: fix current channel is not scanned
All channels should be scanned, including the current channel
when the client is associated.
Removed also unused flag to scan only active channels.
Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Al Viro [Thu, 1 May 2008 02:52:22 +0000 (03:52 +0100)]
Fix dnotify/close race
We have a race between fcntl() and close() that can lead to
dnotify_struct inserted into inode's list *after* the last descriptor
had been gone from current->files.
Since that's the only point where dnotify_struct gets evicted, we are
screwed - it will stick around indefinitely. Even after struct file in
question is gone and freed. Worse, we can trigger send_sigio() on it at
any later point, which allows to send an arbitrary signal to arbitrary
process if we manage to apply enough memory pressure to get the page
that used to host that struct file and fill it with the right pattern...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 1 May 2008 02:50:03 +0000 (19:50 -0700)]
x86: Mark OPTIMIZE_INLINING broken
So Ingo finally did figure out why UML broke with this option: UML
passes gcc the -fno-unit-at-a-time flag, and apparently that wreaks
havoc with gcc's inlining.
We could turn off -fno-unit-at-a-time for UML for gcc4+ (which is what
x86 does), but there's bad blood about this whole option, and it does
show that the thing is just fragile as heck.
So let tempers cool, and disable the thing, and we can revisit the
decision later.
Cc: Adrian Bunk <bunk@kernel.org> Cc: David Miller <davem@davemloft.net> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 1 May 2008 02:31:52 +0000 (19:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes3
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes3: (21 commits)
x86: numaq fix
x86: 8K stacks by default
x86: ioremap ram check fix
x86: fix HT cpu booting on 32-bit
x86: optimize inlining off
x86: CONFIG_X86_ELAN fix
x86: Kconfig fix
x86 PAT: fix performance drop for glx, use UC minus for ioremap(), ioremap_nocache() and pci_mmap_page_range()
x86: use defconfigs from x86/configs/*
toshiba: use ioremap_cached
revert: "x86: ioremap(), extend check to all RAM pages"
x86: don't bother printing compat vdso address
fix: x86: support for new UV apic
x86: fix early-BUG message
x86: iommu_sac_force can become static
x86: add proper header for reboot_force
x86 VISWS: build fix
x86, voyager: fix ioremap_nocache()
hpet: fix
x86: unexport kmap_atomic_to_page
...
Noticed by sparse:
net/mac80211/tkip.c:234:25: warning: right shift by bigger than source value
net/mac80211/tkip.c:235:25: warning: right shift by bigger than source value
net/mac80211/tkip.c:236:25: warning: right shift by bigger than source value
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 24 Apr 2008 12:18:37 +0000 (14:18 +0200)]
mac80211: insert WDS peer after adding interface
This reorders the open code so that WDS peer STA info entries
are added after the corresponding interface is added to the
driver so that driver callbacks aren't invoked out of order.
Also make any master device startup fatal.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
klist: fix coding style errors in klist.h and klist.c
driver core: remove no longer used "struct class_device"
pcmcia: remove pccard_sysfs_interface warnings
devres: support addresses greater than an unsigned long via dev_ioremap
kobject: do not copy vargs, just pass them around
sysfs: sysfs_update_group stub for CONFIG_SYSFS=n
DEBUGFS: Correct location of debugfs API documentation.
driver core: warn about duplicate driver names on the same bus
klist: implement klist_add_{after|before}()
klist: implement KLIST_INIT() and DEFINE_KLIST()
sysfs: Disallow truncation of files in sysfs
David Brownell [Mon, 28 Apr 2008 08:03:20 +0000 (01:03 -0700)]
pcmcia: remove pccard_sysfs_interface warnings
Make the PCMCIA core stop using class_interface to hide socket attribute
registration. This removes the associated section mismatch warnings, and
helps get to the point where that mechanism can finally be removed.
Simplify that attribute registration by using an attribute_group.
This is a net shrink in object size.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kumar Gala [Tue, 29 Apr 2008 15:25:48 +0000 (10:25 -0500)]
devres: support addresses greater than an unsigned long via dev_ioremap
Use a resource_size_t instead of unsigned long since some arch's are
capable of having ioremap deal with addresses greater than the size of a
unsigned long.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Tejun Heo <htejun@gmail.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
driver core: warn about duplicate driver names on the same bus
Currently an attempt to register multiple
drivers with the same name causes the
stack trace with some cryptic error message.
The attached patch adds the necessary check
and the clear error message.
Add klist_add_after() and klist_add_before() which puts a new node
after and before an existing node, respectively. This is useful for
callers which need to keep klist ordered. Note that synchronizing
between simultaneous additions for ordering is the caller's
responsibility.
Ben Hutchings [Mon, 28 Apr 2008 14:59:58 +0000 (15:59 +0100)]
sysfs: Disallow truncation of files in sysfs
sysfs allows attribute files to be truncated, e.g. using ftruncate(), with the
expected effect on their inode. For most attributes, this doesn't change the
"real" size of the file i.e. how much can be read from it. However, the
parameter validation for reading and writing binary attribute files is based
on the inode size and not the size specified in the file's bin_attribute, so it
can be broken by this. For example, if we try using dd to write to such a file:
# pwd
/sys/bus/pci/devices/0000:08:00.0
# ls -l config
-rw-r--r-- 1 root root 4096 Feb 1 17:35 config
# dd if=/dev/zero of=config bs=4 count=1
1+0 records in
1+0 records out
# ls -l config
-rw-r--r-- 1 root root 0 Feb 1 17:50 config
# dd if=/dev/zero of=config bs=4 count=1 seek=128
dd: writing `config': No space left on device
1+0 records in
0+0 records out
Also, after truncation to 0, parameter validation for read and write is
disabled. Most bin_attribute read and write methods also validate the size and
offset, but for some this will allow out-of-range access. This may be a
security issue, though access to such files is often limited to root. In any
case, the validation should remain for safety's sake!)
This was previously reported in Bugzilla as bug 9867.
sysfs should ignore size changes or else refuse them (by returning -EINVAL).
This patch makes it ignore them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavel Emelyanov [Wed, 30 Apr 2008 21:49:54 +0000 (14:49 -0700)]
ipv6: Compilation fix for compat MCAST_MSFILTER sockopts.
The last hunk from the commit dae50295 (ipv4/ipv6 compat: Fix SSM
applications on 64bit kernels.) escaped from the compat_ipv6_setsockopt
to the ipv6_getsockopt (I guess due to patch smartness wrt searching
for context) thus breaking 32-bit and 64-bit-without-compat compilation.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the 'pfn < max_pfn_mapped' check would've caused us to not
enter the loop. Removing that check means we loop infinitely. The
reason for that is because pfn is 0xfffff, and last_addr is 0xffffffcf.
The remaining check that is used to exit the loop is not sufficient;
when pfn<<PAGE_SHIFT is 0xfffff000, that is less than 0xffffffcf; when
we increment pfn and it overflows (pfn == 0x100000), pfn<<PAGE_SHIFT
ends up being 0. That, of course, is less than last_addr. In effect,
pfn<<PAGE_SHIFT is never lower than last_addr.
The simple fix for this is to limit the last_addr check to the PAGE_MASK;
a patch is below.
Signed-off-by: Andres Salomon <dilinger@debian.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since recent smpboot 32/64-bit merge, my dual Xeon with HT has been
booting only 2 of its 4 cpus (when running an i386 kernel; but x86_64
is okay). J.A. Magallón reports the same.
native_cpu_up: bad cpu 2
native_cpu_up: bad cpu 3
The mach-default cpu_present_to_apicid() was just returning cpu number
(2, 3) instead of apicid (6, 7): looks like we now need the x86_64 code
even for the i386 case.
Comparing with other versions of cpu_present_to_apicid(), it seems a
good idea to include an NR_CPUS test too, since cpu_present() doesn't
include that; but that wasn't a problem here, and may no problem at all.
Prior to that smpboot merge, my Xeon booted the two HT siblings on one
physical first, then the two siblings on the other physical after - when
i386, but alternated them when x86_64. Since the merge, the x86_64
sequence is unchanged, but the i386 sequence is now like x86_64.
I prefer this consistency, and I prefer the new sequence: booting with
maxcpus=2 then uses the independent physicals without HT sharing.
x86 PAT: fix performance drop for glx, use UC minus for ioremap(), ioremap_nocache() and pci_mmap_page_range()
Use UC_MINUS for ioremap(), ioremap_nocache() instead of strong UC.
Once all the X drivers move to ioremap_wc(), we can go back to strong
UC semantics for ioremap() and ioremap_nocache().
To avoid attribute aliasing issues, pci_mmap_page_range() will also
use UC_MINUS for default non write-combining mapping request.
Next steps:
a) change all the video drivers using ioremap() or ioremap_nocache()
and adding WC MTTR using mttr_add() to ioremap_wc()
b) for strict usage, we can go back to strong uc semantics
for ioremap() and ioremap_nocache() after some grace period for
completing step-a.
c) user level X server needs to use the appropriate method for setting
up WC mapping (like using resourceX_wc sysfs file instead of
adding MTRR for WC and using /dev/mem or resourceX under /sys)
Sam Ravnborg [Tue, 29 Apr 2008 10:48:15 +0000 (12:48 +0200)]
x86: use defconfigs from x86/configs/*
Daniel Drake <dsd@gentoo.org> reported:
In 2.6.23, if you unpacked a kernel source tarball and then
ran "make menuconfig" you'd be presented with this message:
# using defaults found in arch/i386/defconfig
and the default options would be set.
The same thing in 2.6.24 does not give you any "using defaults" message, and
the default config options within menuconfig are rather blank (e.g. no PCI
support). You can work around this by explicitly running "make defconfig"
before menuconfig, but it would be nice to have the behaviour the way it was
for 2.6.23 (and the way it still is for other archs).
Fixed by adding a x86 specific defconfig list to Kconfig.
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=10470 Tested-by: dsd@gentoo.org Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Alan Cox [Tue, 29 Apr 2008 13:20:23 +0000 (14:20 +0100)]
toshiba: use ioremap_cached
The switch of ioremap to default to uncached doesn't break this driver
but it does needlessly slow it down as BIOS space is cachable and this
driver is quite happy scanning cached ROM space.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
revert: "x86: ioremap(), extend check to all RAM pages"
Vegard Nossum reported a large (150 seconds) boot delay during bootup,
and bisected it to "x86: ioremap(), extend check to all RAM pages"
(commit bdd3cee2e4b). Revert this commit for now.
The kernel prints the compat vdso address regardless of whether compat
vdso mode is enabled or not, which is confusing. Given that this
isn't very interesting information anyway, just remove the printk.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Cc: Gerhard Mack <gmack@innerfire.net> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The .asciz directive takes any number of strings, but each one is zero-
terminated, and string pasting is not done as in C. That results in only the
first line being output.
Replace .asciz with multiple .ascii directives and terminate with .asciz.
Dmitri Vorobiev [Sun, 27 Apr 2008 23:15:58 +0000 (03:15 +0400)]
x86: iommu_sac_force can become static
The iommu_sac_force variable is needlessly defined global,
and this patch makes it static. Additionally, this variable
needs not be explicitly initialized.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
James Bottomley reported that the following commit:
| commit 6371b495991debfd1417b17c2bc4f7d7bae05739
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Wed Jan 30 13:33:40 2008 +0100
|
| x86: change ioremap() to default to uncached
broke Voyager.
James says:
" it broke a class of voyager machines: those which
rely on the quad interrupt controller (QIC). The precis of why they
broke is because the QIC does IPIs (or CPIs in its terminology) via
cache line interference: you interrupt a processor by moving a
designated memory area to write exclusive in the cache (by simply
writing to the line) and the CPU acks the interrupt by moving it back to
read shared (by reading from it). That area, is, of course, mapped by
ioremap, so reversing the ioremap semantics and adding the uncached bit
completely breaks the QIC. "
Sorry about that!
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi_processor_idle and "idle=" boot parameter interaction is broken.
The problem is that, at boot time acpi driver is checking for "idle=" boot
option and not registering the acpi idle handler. But, when there is a CST
changed callback (typically when switching AC <-> battery or suspend-resume)
there are no checks for boot_option_idle_override and acpi idle handler tries
to get installed with nasty side effects.
With CPU_IDLE configured this issue causes results in a nasty oops on CST
change callback and without CPU_IDLE there is no oops, but boot option
of "idle=" gets ignored and acpi idle handler gets installed.
Change the behavior to not do anything in acpi idle handler when there is a
"idle=" boot option.
Note that the problem is only there when "idle=" boot option is used.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Sam Ravnborg [Tue, 29 Apr 2008 20:52:01 +0000 (22:52 +0200)]
acpi: fix section mismatch warning in pnpacpi
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x153d69): Section mismatch in reference from the function is_exclusive_device() to the variable .init.data:excluded_id_list
is_exclusive_device is only used from __init context so document
this with the __init annotation and get rid of the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
projects / linux-2.6-omap-h63xx.git / log