Ben Dooks [Tue, 20 Feb 2007 21:58:01 +0000 (13:58 -0800)]
[PATCH] mfd: SM501 core driver
This driver provides the core functionality of the SM501, which is a
multi-function chip including two framebuffers, video acceleration, USB,
and many other peripheral blocks.
The driver exports a number of entries for the peripheral drivers to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miguel Ojeda [Tue, 20 Feb 2007 21:58:00 +0000 (13:58 -0800)]
[PATCH] cfag12864b: fix crash when built-in and no parport present
The problem comes when ks0108/cfag12864b are built-in and no parallel port is
present. ks0108_init() is called first, as it should be, but fails to load
(as there is no parallel port to use).
After that, cfag12864b_init() gets called, without knowing anything about
ks0108 failed, and calls ks0108_writecontrol(), which dereferences an
uninitialized pointer.
Init order is OK, I think. The problem is how to stop cfag12864b_init() being
called if ks0108 failed to load. modprobe does it for us, but, how when
built-in?
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Tue, 20 Feb 2007 21:57:56 +0000 (13:57 -0800)]
[PATCH] fault injection: split up stacktrace filter Kconfig option
There is no prompt for CONFIG_STACKTRACE, so FAULT_INJECTION cannot be
selected without LOCKDEP enabled. (found by Paolo 'Blaisorblade'
Giarrusso)
In order to fix such broken Kconfig dependency, this patch splits up the
stacktrace filter support for fault injection by new Kconfig option, which
enables to use fault injection on the architecture which doesn't have
general stacktrace support.
Cc: "Paolo 'Blaisorblade' Giarrusso" <blaisorblade@yahoo.it> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Srinivasa Ds [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] kprobes: list all active probes in the system
This patch lists all active probes in the system by scanning through
kprobe_table[]. It takes care of aggregate handlers and prints the type of
the probe. Letter "k" for kprobes, "j" for jprobes, "r" for kretprobes.
It also lists address of the instruction,its symbolic name(function name +
offset) and the module name. One can access this file through
/sys/kernel/debug/kprobes/list.
Output looks like this
=====================
llm40:~/a # cat /sys/kernel/debug/kprobes/list c0169ae3 r sys_read+0x0 c0169ae3 k sys_read+0x0 c01694c8 k vfs_write+0x0 c0167d20 r sys_open+0x0 f8e658a6 k reiserfs_delete_inode+0x0 reiserfs c0120f4a k do_fork+0x0 c0120f4a j do_fork+0x0 c0169b4a r sys_write+0x0 c0169b4a k sys_write+0x0 c0169622 r vfs_read+0x0
=================================
[akpm@linux-foundation.org: cleanup]
[ananth@in.ibm.com: sparc build fix] Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com> Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] fs: fix __block_write_full_page error case buffer submission
Andrew noticed that unlocking the page before submitting all buffers for
writeout could cause problems if the IO completes before we've finished
messing around with the page buffers, and they subsequently get freed.
Even if there were no bug, it is a good idea to bring the error case
into line with the common case here.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] shm: make sysv ipc shared memory use stacked files
The current ipc shared memory code runs into several problems because it
does not quite use files like the rest of the kernel. With the option of
backing ipc shared memory with either hugetlbfs or ordinary shared memory
the problems got worse. With the added support for ipc namespaces things
behaved so unexpected that we now have several bad namespace reference
counting bugs when using what appears at first glance to be a reasonable
idiom.
So to attack these problems and hopefully make the code more maintainable
this patch simply uses the files provided by other parts of the kernel and
builds it's own files out of them. The shm files are allocated in do_shmat
and freed when their reference count drops to zero with their last unmap.
The file and vm operations that we don't want to implement or we don't
implement completely we just delegate to the operations of our backing
file.
This means that we now get an accurate shm_nattch count for we have a
hugetlbfs inode for backing store, and the shm accounting of last attach
and last detach time work as well.
This means that getting a reference to the ipc namespace when we create the
file and dropping the referenece in the release method is now safe and
correct.
This means we no longer need a special case for clearing VM_MAYWRITE
as our file descriptor now only has write permissions when we have
requested write access when calling shmat. Although VM_SHARED is now
cleared as well which I believe is harmless and is mostly likely a
minor bug fix.
By using the same set of operations for both the hugetlb case and regular
shared memory case shmdt is not simplified and made slightly more correct
as now the test "vma->vm_ops == &shm_vm_ops" is 100% accurate in spotting
all shared memory regions generated from sysvipc shared memory.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] slab: reduce size of alien cache to cover only possible nodes
The alien cache is a per cpu per node array allocated for every slab on the
system. Currently we size this array for all nodes that the kernel does
support. For IA64 this is 1024 nodes. So we allocate an array with 1024
objects even if we only boot a system with 4 nodes.
This patch uses "nr_node_ids" to determine the number of possible nodes
supported by a hardware configuration and only allocates an alien cache
sized for possible nodes.
The initialization of nr_node_ids occurred too late relative to the bootstrap
of the slab allocator and so I moved the setup_nr_node_ids() into
free_area_init_nodes().
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] Convert highest_possible_processor_id to nr_cpu_ids
We frequently need the maximum number of possible processors in order to
allocate arrays for all processors. So far this was done using
highest_possible_processor_id(). However, we do need the number of
processors not the highest id. Moreover the number was so far dynamically
calculated on each invokation. The number of possible processors does not
change when the system is running. We can therefore calculate that number
once.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Frederik Deweerdt <frederik.deweerdt@gmail.com> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] Replace highest_possible_node_id() with nr_node_ids
highest_possible_node_id() is currently used to calculate the last possible
node idso that the network subsystem can figure out how to size per node
arrays.
I think having the ability to determine the maximum amount of nodes in a
system at runtime is useful but then we should name this entry
correspondingly, it should return the number of node_ids, and the the value
needs to be setup only once on bootup. The node_possible_map does not
change after bootup.
This patch introduces nr_node_ids and replaces the use of
highest_possible_node_id(). nr_node_ids is calculated on bootup when the
page allocators pagesets are initialized.
[deweerdt@free.fr: fix oops] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] fix mempolicy's check on a system with memory-less-node
bind_zonelist() can create zero-length zonelist if there is a
memory-less-node. This patch checks the length of zonelist. If length is
0, returns -EINVAL.
tested on ia64/NUMA with memory-less-node.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: Andi Kleen <ak@suse.de> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:57:48 +0000 (13:57 -0800)]
[PATCH] rework reserved major handling
Several people have reported failures in dynamic major device number handling
due to the recent changes in there to avoid handing out the local/experimental
majors.
Rolf reports that this is due to a gcc-4.1.0 bug.
The patch refactors that code a lot in an attempt to provoke the compiler into
behaving.
Andries Brouwer [Tue, 20 Feb 2007 21:57:47 +0000 (13:57 -0800)]
[PATCH] minix v3: fix superblock definition
Somehow we got the layout of the v3 superblock wrong, which causes crashes due
to overindexing of the buffer_head array in statfs on large fielsystems.
Linus Torvalds [Tue, 20 Feb 2007 18:26:46 +0000 (10:26 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (21 commits)
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
natsemi: Add support for using MII port with no PHY
skge: race with workq and RTNL
Replace local random function with random32()
s2io: RTNL and flush_scheduled_work deadlock
8139too: RTNL and flush_scheduled_work deadlock
sis190: RTNL and flush_scheduled_work deadlock
r8169: RTNL and flush_scheduled_work deadlock
[PATCH] ieee80211softmac: Fix setting of initial transmit rates
[PATCH] bcm43xx: OFDM fix for rev 1 cards
[PATCH] bcm43xx: Fix for 4311 and 02/07/07 specification changes
[PATCH] prism54: correct assignment of DOT1XENABLE in WE-19 codepaths
[PATCH] zd1211rw: Readd zd_addr_t cast
[PATCH] bcm43xx: Fix for oops on resume
[PATCH] bcm43xx: Ignore ampdu status reports
[PATCH] wavelan: Use ARRAY_SIZE macro when appropriate
[PATCH] hostap: Use ARRAY_SIZE macro when appropriate
[PATCH] misc-wireless: Use ARRAY_SIZE macro when appropriate
[PATCH] ipw2100: Use ARRAY_SIZE macro when appropriate
[PATCH] bcm43xx: Janitorial change - remove two unused variables
...
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[PATCH] ARM: fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 20 Feb 2007 18:14:29 +0000 (10:14 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[NET] Eliminate user-selectable CONFIG_MV643XX_ETH_[012]
[MIPS] Drop __init from init_8259A()
[MIPS] Fix Kconfig typo bug
[MIPS] Fix double signal on trap and break instruction
[MIPS] sigset_32 has been made redundand by compat_sigset_t.
[MIPS] emma2rh: Remove needless <asm/i8259.h> inclusion.
[MIPS] Add MTD device support for Cobalt
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Jeff Garzik <jeff@garzik.org> Cc: Paul Mackerras <paulus@samba.org>
Mark Brown [Mon, 19 Feb 2007 20:15:40 +0000 (20:15 +0000)]
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY. This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Brown [Mon, 19 Feb 2007 20:15:39 +0000 (20:15 +0000)]
natsemi: Add support for using MII port with no PHY
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool. Any PHYs that are present can be accessed via the MII
ioctl()s.
This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Russell King [Tue, 20 Feb 2007 15:44:23 +0000 (15:44 +0000)]
[ARM] Fix ARM AACI ALSA driver
CC [M] sound/arm/aaci.o
sound/arm/aaci.c:729: error: parse error before '*' token
sound/arm/aaci.c:731: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:786: error: parse error before '*' token
sound/arm/aaci.c:786: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:827: error: parse error before '*' token
sound/arm/aaci.c:828: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:845: error: parse error before "aaci_capture_ops"
sound/arm/aaci.c:845: warning: type defaults to `int' in declaration of `aaci_capture_ops'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[ARM] fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 15:23:57 +0000 (15:23 +0000)]
[ARM] Fix jornada720 build errors
kernel/built-in.o: In function `pm_suspend':
utsname_sysctl.c:(.text+0x23008): multiple definition of `pm_suspend'
arch/arm/mach-sa1100/built-in.o:arch/arm/mach-sa1100/sleep.S:(.text+0xf68): first defined here
arm-linux-ld: Warning: size of symbol `pm_suspend' changed from 20 in arch/arm/mach-sa1100/built-in.o to 44 in kernel/built-in.o
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 14:56:51 +0000 (14:56 +0000)]
[ARM] Fix iop13xx build error
CC arch/arm/mach-iop13xx/setup.o
arch/arm/mach-iop13xx/setup.c: In function 'iq8134x_probe_flash_size':
arch/arm/mach-iop13xx/setup.c:210: warning: implicit declaration of function 'ioremap'
arch/arm/mach-iop13xx/setup.c:210: warning: initialization makes pointer from integer without a cast
arch/arm/mach-iop13xx/setup.c:218: warning: implicit declaration of function 'writew'
arch/arm/mach-iop13xx/setup.c:222: warning: implicit declaration of function 'readb'
arch/arm/mach-iop13xx/setup.c:231: warning: implicit declaration of function 'iounmap'
LD .tmp_vmlinux1
arch/arm/mach-iop13xx/built-in.o: In function `iop13xx_platform_init':
iq81340mc.c:(.init.text+0x150): undefined reference to `ioremap'
iq81340mc.c:(.init.text+0x21c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x24c): undefined reference to `writew'
iq81340mc.c:(.init.text+0x254): undefined reference to `iounmap'
iq81340mc.c:(.init.text+0x2c4): undefined reference to `readb'
iq81340mc.c:(.init.text+0x2e8): undefined reference to `readb'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Sat, 10 Feb 2007 23:07:48 +0000 (23:07 +0000)]
backlight: Separate backlight properties from backlight ops pointers
Per device data such as brightness belongs to the indivdual device
and should therefore be separate from the the backlight operation
function pointers. This patch splits the two types of data and
allows simplifcation of some code.
fb_info->bl_mutex is badly thought out and the backlight class doesn't
need it if the framebuffer/backlight register/unregister order is
consistent, particularly after the backlight locking fixes.
Richard Purdie [Fri, 9 Feb 2007 09:46:45 +0000 (09:46 +0000)]
backlight/fbcon: Add FB_EVENT_CONBLANK
The backlight class wants notification whenever the console is blanked
but doesn't get this when hardware blanking fails and software blanking
is used. Changing FB_EVENT_BLANK to report both would be a behaviour
change which could confuse the console layer so add a new event for
software blanking and have the backlight class listen for both.
Richard Purdie [Thu, 8 Feb 2007 22:25:09 +0000 (22:25 +0000)]
backlight: Fix external uses of backlight internal semaphore
backlight_device->sem has a very specific use as documented in the
header file. The external users of this are using it for a different
reason, to serialise access to the update_status() method.
backlight users were supposed to implement their own internal
serialisation of update_status() if needed but everyone is doing
things differently and incorrectly. Therefore add a global mutex to
take care of serialisation for everyone, once and for all.
Locking for get_brightness remains optional since most users don't
need it.
Add control of LCD backlight for Frontpath ProGear HX1050+.
Patch is based on http://downloads.sf.net/progear/progear-lcd-0.2.tar.gz
driver by M Schacht.
Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl> Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Linus Torvalds [Tue, 20 Feb 2007 01:38:33 +0000 (17:38 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Cobalt: Fix UART I/O type
[MIPS] Fixup copy_from_user_inatomic
[MIPS] Fix struct sigcontext for N32 userland
[MIPS] Make some __setup functions static
[MIPS] Declare highstart_pfn, highend_pfn only if CONFIG_HIGHMEM=y
[MIPS] Allow selection of KGDB only on platforms where it's supported.
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source
address is not immediately available the copy fails *and* *zeros* *the*
*destination*.
This is a problem because a concurrent read (which admittedly is an odd
thing to do) might see zeros rather that was there before the write, or
what was there after, or some mixture of the two (any of these being a
reasonable thing to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't
cause an error.
The first copying does not need to zero any uncopied bytes, and doing
so causes the problem. It uses copy_from_user_atomic rather than
copy_from_user so the simple expedient is to change copy_from_user_atomic
to *not* zero out bytes on failure.
< --- end cite --- >
This patch finally implements at least a not so pretty solution by
duplicating the relevant part of __copy_user.
Atsushi Nemoto [Sat, 17 Feb 2007 15:12:57 +0000 (00:12 +0900)]
[MIPS] Fix struct sigcontext for N32 userland
The kernel use 64-bit for sc_regs[0], and both N32/N64 userland
expects it was 64-bit. But size of 'long' on N32 is actually 32-bit.
So this definition make some confusion. Use __u32 and __u64 for
N32/N64 sigcontext to get rid of this confusion.
Greg Banks [Mon, 19 Feb 2007 23:12:34 +0000 (10:12 +1100)]
[PATCH] Fix a free-wrong-pointer bug in nfs/acl server.
Due to type confusion, when an nfsacl verison 2 'ACCESS' request
finishes and tries to clean up, it calls fh_put on entiredly the
wrong thing and this can cause an oops.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sat, 17 Feb 2007 19:03:21 +0000 (20:03 +0100)]
[PATCH] tick management: make broadcast dependent on local APIC
The broadcast functionality is only necessary when a local APIC is
available. Make the config switch depend on X86_LOCAL_APIC. This
resolves the mach-voyager breakage introduced by the tick managament
code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Mon, 19 Feb 2007 18:12:05 +0000 (18:12 +0000)]
[PATCH] NOHZ: Produce debug output instead of a BUG()
The BUG_ON() in tick_nohz_stop_sched_tick() triggers on some boxen.
Remove the BUG_ON and print information about the pending softirq
to allow better debugging of the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 19 Feb 2007 21:38:42 +0000 (13:38 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Update defconfigs
[MIPS] Support for several more SNI RM models.
[MIPS] Include <asm/bugs> to for declaration of check_bugs32.
[MIPS] Add external declaration of pagetable_init() to pgalloc.h
[MIPS] Make kernel_thread_helper() static
[MIPS] Make __declare_dbe_table static and avoid it getting optimized away
[MIPS] Use MIPS R2 instructions for bitops.
[MIPS] signals: Share even more code.
[MIPS] Fix CONFIG_MIPS32_N32=y CONFIG_MIPS32_O32=n build
[MIPS] Iomap implementation.
[MIPS] <asm/compat-signal.h> needs to include <asm/uaccess.h>.
[MIPS] IP27: Fix warning.
[MIPS] Fix sigset_t endianess swapping issues in 32-bit compat code.
Linus Torvalds [Mon, 19 Feb 2007 21:36:16 +0000 (13:36 -0800)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon/vt1211: Add probing of alternate config index port
hwmon/f71805f: Fix a race condition
hwmon/abituguru: Fix unchecked return status
hwmon: New driver for the Analog Devices ADM1029
hwmon/w83627ehf: Add support for the W83627DHG chip
hwmon: Use subsys_initcall
hwmon/lm70: Make lm70_remove a __devexit function
hwmon: Cleanup a bogus legacy comment
hwmon: Simplify the locking model of two drivers
hwmon: Drop unused mutexes in two drivers
hwmon/it87: Add PWM base frequency control
Linus Torvalds [Mon, 19 Feb 2007 21:33:01 +0000 (13:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: implement optional loose read cache
9p: Use kthread_stop instead of sending a SIGKILL.
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] SCSI core: better initialization for sdev->scsi_level
[SCSI] scsi_proc.c: display sdev->scsi_level correctly
[SCSI] megaraid_sas: update version and author info
[SCSI] megaraid_sas: return sync cache call with success
[SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
[SCSI] megaraid_sas: add bios_param in scsi_host_template
[SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
[SCSI] scsi_transport.h should include scsi_device.h
[SCSI] aic79xx: remove extra newline from info message
[SCSI] scsi_scan.c: handle bad inquiry responses
[SCSI] aic94xx: tie driver to the major number of the sequencer firmware
[SCSI] lpfc: add PCI error recovery support
[SCSI] megaraid: pci_module_init to pci_register_driver
[SCSI] tgt: fix the user/kernel ring buffer interface
[SCSI] sgiwd93: interfacing to wd33c93
[SCSI] wd33c93: Fast SCSI with WD33C93B
Linus Torvalds [Mon, 19 Feb 2007 21:31:34 +0000 (13:31 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: remove obsolete setup parameters from input drivers
Input: HIL - fix improper call to release_region()
Input: hid-lgff - treat devices as joysticks unless told otherwise
Input: HID - add support for Logitech Formula Force EX
Input: gpio-keys - switch to common GPIO API
Input: do not lock device when showing name, phys and uniq
Input: i8042 - let serio bus suspend ports
Input: psmouse - properly reset mouse on shutdown/suspend
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
Linus Torvalds [Mon, 19 Feb 2007 21:23:50 +0000 (13:23 -0800)]
Merge branch 'acpi' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'acpi' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: wrong sizeof for BUFFER
[PATCH] libata: change order of _SDD/_GTF execution (resend #3)
[PATCH] libata: ACPI _SDD support
[PATCH] libata: ACPI and _GTF support
projects / linux-2.6-omap-h63xx.git / log