Anton Vorontsov [Thu, 23 Oct 2008 19:06:56 +0000 (21:06 +0200)]
[ARM] pxa: add basic support for HP iPAQ h5000
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.
Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).
Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.
This machine will be used as "real user" for these new drivers.
This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by: Milan Plzik <milan.plzik@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Robert Jarzmik [Sat, 15 Nov 2008 15:09:59 +0000 (16:09 +0100)]
[ARM] pxa/MioA701: improve power supply sources
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Robert Jarzmik [Tue, 18 Nov 2008 19:23:32 +0000 (20:23 +0100)]
[ARM] pxa/MioA701: discovered new gpio definitions.
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Robert Jarzmik [Sat, 15 Nov 2008 15:09:58 +0000 (16:09 +0100)]
[ARM] pxa/MioA701: change reset function to preserve RTC.
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Robert Jarzmik [Sat, 15 Nov 2008 15:09:54 +0000 (16:09 +0100)]
[ARM] pxa/MioA701: add camera support for Mio A701 board.
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Philipp Zabel [Sun, 29 Jun 2008 14:53:34 +0000 (16:53 +0200)]
[ARM] pxa: cpufreq-pxa2xx: sdram_rows detection support
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Marc Zyngier [Tue, 4 Nov 2008 12:33:25 +0000 (13:33 +0100)]
[ARM] pxa: cpufreq-pxa2xx: allow frequency table selection
Following the removal of the "->policy" usage for PXA255 in patch 459fc208abd1b365fa013c17d433dfb5b4bc1e3a (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org> Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Eric Miao [Sat, 29 Nov 2008 13:42:39 +0000 (21:42 +0800)]
[ARM] pxa: add base PXA935 support due to CPUID change
PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Eric Miao [Fri, 28 Nov 2008 06:19:33 +0000 (14:19 +0800)]
[ARM] pxa: move AC97 register definitions into dedicated regs-ac97.h
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Eric Miao [Fri, 28 Nov 2008 05:38:03 +0000 (13:38 +0800)]
[ARM] pxa: remove the now unused IMPMCR/IMPMSR register definitions
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Eric Miao [Thu, 27 Nov 2008 09:08:42 +0000 (17:08 +0800)]
[ARM] pxa: remove unused PWM register definitions, use generic PWM API
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Eric Miao [Sun, 30 Nov 2008 12:58:42 +0000 (20:58 +0800)]
[ARM] pxa: removed unused declarations of pxa_gpio_* in hardware.h
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Eric Miao [Wed, 26 Nov 2008 10:12:04 +0000 (18:12 +0800)]
[ARM] pxa: add support for additional GPIOs on PXA26x
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
Linus Torvalds [Fri, 21 Nov 2008 02:08:09 +0000 (18:08 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp> Signed-off-by: Tony Luck <tony.luck@intel.com>
Hidetoshi Seto [Mon, 17 Nov 2008 01:18:08 +0000 (10:18 +0900)]
[IA64] use mprintk instead of printk, in ia64_mca_modify_original_stack
Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Tony Luck [Thu, 20 Nov 2008 21:27:12 +0000 (13:27 -0800)]
[IA64] Rationalize kernel mode alignment checking
Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:
* Base kernel code ran in permissive mode where the only traps
generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
unaligned accesses caused traps to the 0x5a00 unaligned reference
vector.
Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Matthew Wilcox [Thu, 20 Nov 2008 21:09:33 +0000 (14:09 -0700)]
x86: Fix interrupt leak due to migration
When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used. If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.
This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trond Myklebust [Thu, 20 Nov 2008 21:06:21 +0000 (16:06 -0500)]
SUNRPC: Fix a performance regression in the RPC authentication code
Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.
It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.
The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Do not attempt to close invalidated file handles
[CIFS] fix check for dead tcon in smb_init
Linus Torvalds [Thu, 20 Nov 2008 21:13:48 +0000 (13:13 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: csrc-r4k: Fix declaration depending on the wrong CONFIG_ symbol.
MIPS: csrc-r4k: Fix spelling mistake.
MIPS: RB532: Provide functions for gpio configuration
MIPS: IP22: Make indy_sc_ops variable static
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
MIPS: Malta: Fix include paths in malta-amon.c
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (23 commits)
net: fix tiny output corruption of /proc/net/snmp6
atl2: don't request irq on resume if netif running
ipv6: use seq_release_private for ip6mr.c /proc entries
pkt_sched: fix missing check for packet overrun in qdisc_dump_stab()
smc911x: Fix printf format typo in smc911x driver.
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
mv643xx_eth: fix recycle check bound
mv643xx_eth: fix the order of mdiobus_{unregister, free}() calls
sh: sh_eth: Update to change of mii_bus
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
TPROXY: fill struct flowi->flags in udp_sendmsg()
net: ipg.c fix bracing on endian swapping
phylib: Fix auto-negotiation restart avoidance
net: jme.c rxdesc.flags is __le16, other missing endian swaps
phylib: fix phy name example in documentation
net: Do not fire linkwatch events until the device is registered.
phonet: fix compilation with gcc-3.4
ixgbe: fix compilation with gcc-3.4
pktgen: fix multiple queue warning
net: fix ip_mr_init() error path
...
Linus Torvalds [Thu, 20 Nov 2008 21:09:32 +0000 (13:09 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: uaccess_64: fix return value in __copy_from_user()
x86: quirk for reboot stalls on a Dell Optiplex 330
Helge Deller [Thu, 20 Nov 2008 09:54:09 +0000 (10:54 +0100)]
parisc: fix bug in compat_arch_ptrace
Commit 81e192d6ce303b6792aa38ff35f41a1a7357f23a ("parisc: convert to
generic compat_sys_ptrace") introduced a bug which segfaults the parisc
64bit kernel when stracing 32bit applications:
The problem is that compat_arch_ptrace() enters with an addr value of
type compat_ulong_t and calls translate_usr_offset() to translate the
address offset into a struct pt_regs offset like this:
addr = translate_usr_offset(addr)
this means that any return value of translate_usr_offset() is stored
back as compat_ulong_t type into the addr variable.
But since translate_usr_offset() returns -1 for invalid offsets, addr
can now get the value 0xffffffff which then fails the next return-value
sanity check and thus the kernel tries to access invalid memory:
if (addr < 0)
break;
Fix this bug by modifying translate_usr_offset() to take and return
values of type compat_ulong_t, and by returning the value
"sizeof(struct pt_regs)" as an error indicator.
Additionally change the sanity check to check for return values
for >= sizeof(struct pt_regs).
Steve French [Thu, 20 Nov 2008 20:00:44 +0000 (20:00 +0000)]
[CIFS] Do not attempt to close invalidated file handles
If a connection with open file handles has gone down
and come back up and reconnected without reopening
the file handle yet, do not attempt to send an SMB close
request for this handle in cifs_close. We were
checking for the connection being invalid in cifs_close
but since the connection may have been reconnected
we also need to check whether the file handle
was marked invalid (otherwise we could close the
wrong file handle by accident).
Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Phil Sutter [Sat, 1 Nov 2008 14:13:21 +0000 (15:13 +0100)]
MIPS: RB532: Provide functions for gpio configuration
As gpiolib doesn't support pin multiplexing, it provides no way to
access the GPIOFUNC register. Also there is no support for setting
interrupt status and level. These functions provide access to them and
are needed by the CompactFlash driver.
Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Florian Fainelli [Fri, 31 Oct 2008 13:24:29 +0000 (14:24 +0100)]
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
This patch fixes the wrong use of GPIO register offsets
in devices.c. To avoid further problems, use gpio_get_value
to return the NAND status instead of our own expanded code.
Also define the zero offset of the alternate function register to allow
consistent access.
Alan Jenkins [Thu, 20 Nov 2008 12:18:25 +0000 (04:18 -0800)]
atl2: don't request irq on resume if netif running
If the device is suspended with the cable disconnected, then
resumed with the cable connected, dev->open is called before
resume. During resume, we request an IRQ, but the IRQ was
already assigned during dev->open, resulting in the warning
shown below.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Thu, 20 Nov 2008 12:16:12 +0000 (04:16 -0800)]
ipv6: use seq_release_private for ip6mr.c /proc entries
In ip6mr.c, /proc entries /proc/net/ip6_mr_cache and /proc/net/ip6_mr_vif
are opened with seq_open_private(), thus seq_release_private() should be
used to release them.
Should fix a small memory leak.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
asix: Fix asix-based cards connecting to 10/100Mbs LAN.
Add AX_MEDIUM_ENCK also when speed = 10/100Mbps. This allows my belkin f5d5055 to work with my 100Mbps switch and with an old 10Mbps ISA card.
Without this patch, the card is recognized and the interface is brought
up fine, but no packets actually flow through the interface.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com> Acked-by: David Hollis <dhollis@davehollis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When mv643xx_eth allocates skbuffs, it adds
'dma_get_cache_alignment() - 1' to the length it needs, so that it can
align the skb's ->data pointer to a cache boundary. When checking
whether a transmitted skbuff can be reused as a receive buffer, these
bytes needs to be included into the minimum bound for the recycle check.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Balazs Scheidler [Thu, 20 Nov 2008 09:08:06 +0000 (01:08 -0800)]
TPROXY: supply a struct flowi->flags argument in inet_sk_rebuild_header()
inet_sk_rebuild_header() does a new route lookup if the dst_entry
associated with a socket becomes stale. However inet_sk_rebuild_header()
didn't use struct flowi->flags, causing the route lookup to
fail for foreign-bound IP_TRANSPARENT sockets, causing an error
state to be set for the sockets in question.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Balazs Scheidler [Thu, 20 Nov 2008 09:07:24 +0000 (01:07 -0800)]
TPROXY: fill struct flowi->flags in udp_sendmsg()
udp_sendmsg() didn't fill struct flowi->flags, which means that
the route lookup would fail for non-local IPs even if the
IP_TRANSPARENT sockopt was set.
This prevents sendto() to work properly for UDP sockets, whereas
bind(foreign-ip) + connect() + send() worked fine.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Pete Zaitcev [Fri, 14 Nov 2008 16:47:41 +0000 (09:47 -0700)]
USB: usbmon: fix read(2)
There's a bug in the usbmon binary reader: When using read() to fetch
the packets and a packet's data is partially read, the next read call
will once again return up to len_cap bytes of data. The b_read counter
is not regarded when determining the remaining chunk size.
So, when dumping USB data with "cat /dev/usbmon0 > usbmon.trace" while
reading from a USB storage device and analyzing the dump file
afterwards it will get out of sync after a couple of packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de> Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Richard Röjfors [Sun, 16 Nov 2008 03:53:24 +0000 (19:53 -0800)]
USB: gadget rndis: send notifications
It turns out that atomic_inc_return() returns the *new* value
not the original one, so the logic in rndis_response_available()
kept the first RNDIS response notification from getting out.
This prevented interoperation with MS-Windows (but not Linux).
Fix this to make RNDIS behave again.
Signed-off-by: Richard Röjfors <richard.rojfors@endian.se> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 16 Nov 2008 03:53:21 +0000 (19:53 -0800)]
USB: gadget rndis: stop windows self-immolation
Somewhere in the conversion of the RNDIS gadget code to the new
framework, the descriptor of its data interface seems to have
been copied from the CDC Ethernet driver. Unfortunately that
means it got a nonzero altsetting ... which is incorrect. Issue
uncovered by Richard Röjfors <richard.rojfors@endian.se>.
This patch fixes that problem, and resolves at least some cases
of Windows XP bluescreening itself.
Tested-by: Richard Röjfors <richard.rojfors@endian.se>. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 17 Nov 2008 19:32:16 +0000 (14:32 -0500)]
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
This patch (as1168) updates the unusual_devs entry for the Nokia 5300.
According to Jorge Lucangeli Obes <t4m5yn@gmail.com>, some existing
models have a revision number lower than the lower limit of the
current entry.
The patch also moves the entry for the Nokia 5310 to its correct place
in the file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 17 Nov 2008 21:12:32 +0000 (16:12 -0500)]
USB: storage: updates unusual_devs entry for the Nokia 6300
This patch (as1169) modifies the unusual_devs entry for the Nokia
6300. According to Maciej Gierok <mgierok@gmail.com> and David
McBride <dwm@doc.ic.ac.uk>, the revision limits need to be wider.
This fixes Bugzilla #11768.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Fri, 14 Nov 2008 03:42:29 +0000 (11:42 +0800)]
USB: fix SB700 usb subsystem hang bug
This patch is required for AMD SB700 south bridge revision A12 and A13 to avoid
USB subsystem hang symptom. The USB subsystem hang symptom is observed when the
system has multiple USB devices connected to it. In some cases a USB hub may be
required to observe this symptom.
This patch works around the problem by correcting the internal register setting
that will help by changing the behavior of the internal logic to avoid the
USB subsystem hang issue. The change in the behavior of the logic does not
impact the normal operation of the USB subsystem.
Linus Torvalds [Thu, 20 Nov 2008 02:53:02 +0000 (18:53 -0800)]
Merge branch 'x86/numa' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86/numa' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: make NUMA on 32-bit depend on EXPERIMENTAL again
x86, hibernate: fix breakage on x86_32 with CONFIG_NUMA set
Linus Torvalds [Thu, 20 Nov 2008 02:51:56 +0000 (18:51 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: more general identifier for Phoenix BIOS
AMD IOMMU: check for next_bit also in unmapped area
AMD IOMMU: fix fullflush comparison length
AMD IOMMU: enable device isolation per default
AMD IOMMU: add parameter to disable device isolation
x86, PEBS/DS: fix code flow in ds_request()
x86: add rdtsc barrier to TSC sync check
xen: fix scrub_page()
x86: fix es7000 compiling
x86, bts: fix unlock problem in ds.c
x86, voyager: fix smp generic helper voyager breakage
x86: move iomap.h to the new include location
Randy Dunlap [Wed, 19 Nov 2008 23:36:51 +0000 (15:36 -0800)]
cciss: fix DEBUG printk formats
Fix printk format warnings when CCISS_DEBUG is defined.
drivers/block/cciss.c:2856: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3205: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/block/cciss.c:3236: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
drivers/block/cciss.c:3246: warning: format '%x' expects type 'unsigned int', but argument 2 has type '__u64'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Mike Miller <mike.miller@hp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Wed, 19 Nov 2008 23:36:49 +0000 (15:36 -0800)]
drivers/video/backlight/da903x.c: introduce one more missing kfree
One more error handling code should have kfree as well
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WANG Cong [Wed, 19 Nov 2008 23:36:46 +0000 (15:36 -0800)]
hostfs: fix a duplicated global function name
fs/hostfs/hostfs_user.c defines do_readlink() as non-static, and so does
fs/xfs/linux-2.6/xfs_ioctl.c when CONFIG_XFS_DEBUG=y. So rename
do_readlink() in hostfs to hostfs_do_readlink().
I think it's better if XFS guys will also rename their do_readlink(),
it's not necessary to use such a general name.
Signed-off-by: WANG Cong <wangcong@zeuux.org> Cc: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlada Peric [Wed, 19 Nov 2008 23:36:45 +0000 (15:36 -0800)]
cirrusfb: remove unused variables
After commit a1d35a7a (cirrusfb: use modedb and add mode_option
parameter), these variables are no longer used, so remove them to fix
compilation warning.
Signed-off-by: Vlada Periæ <vlada.peric@gmail.com> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steven Rostedt [Wed, 19 Nov 2008 23:36:43 +0000 (15:36 -0800)]
MAINTAINERS: change email address for rostedt
I find that I answer my email quicker on my home email account, than I do
on my work email. Not to mention that I never check my work email while
traveling. Please change my email address in the MAINTAINERS file from
srostedt@redhat.com to rostedt@goodmis.org.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Henrik Rydberg [Wed, 19 Nov 2008 23:36:42 +0000 (15:36 -0800)]
drivers/hwmon/applesmc.c: add generic MacPro support
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
Signed-off-by: Julia Lawall <julia@diku.dk> Cc: Mike Rapoport <mike@compulab.co.il> Cc: Richard Purdie <rpurdie@linux.intel.com> Cc: Eric Miao <eric.miao@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Wed, 19 Nov 2008 23:36:38 +0000 (15:36 -0800)]
don't unlink an active swapfile
Peter Cordes is sorry that he rm'ed his swapfiles while they were in use,
he then had no pathname to swapoff. It's a curious little oversight, but
not one worth a lot of hackery. Kudos to Willy Tarreau for turning this
around from a discussion of synthetic pathnames to how to prevent unlink.
Mimic immutable: prohibit unlinking an active swapfile in may_delete()
(and don't worry my little head over the tiny race window).
Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: Willy Tarreau <w@1wt.eu> Acked-by: Christoph Hellwig <hch@infradead.org> Cc: Peter Cordes <peter@cordes.ca> Cc: Bodo Eggert <7eggert@gmx.de> Cc: David Newall <davidn@davidnewall.com> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6-omap-h63xx.git / log