Michael Buesch [Fri, 19 Dec 2008 17:40:00 +0000 (18:40 +0100)]
b43: Suspend MAC while killing the radio
We should suspend the MAC, before we kill the radio. This gives
the MAC a chance to leave any TX/RX state and it avoids races on
the PHY/RADIO registers.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Fri, 19 Dec 2008 04:23:05 +0000 (23:23 -0500)]
ath5k: correct packet length in tx descriptors
Packet length calculation (which includes frame check sequence)
should take into account whether we add a pad field or not.
Extract the calculation into a helper and use it in both places.
Changes to desc.c
Changes-licensed-under: ISC
Changes to ath5k.h, base.c
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Dec 2008 21:35:27 +0000 (23:35 +0200)]
mac80211: implement dynamic power save
This patch implements dynamic power save for mac80211. Basically it
means enabling power save mode after an idle period. Implementing it
dynamically gives a good compromise of low power consumption and low
latency. Some hardware have support for this in firmware, but some
require the host to do it.
The dynamic power save is implemented by adding an timeout to
ieee80211_subif_start_xmit(). The timeout can be enabled from userspace
with Wireless Extensions. For example, the command below enables the
dynamic power save and sets the time timeout to 500 ms:
iwconfig wlan0 power timeout 500m
Power save now only works with devices which handle power save in firmware.
It's also disabled by default and the heuristics when and how to enable is
considered as a policy decision and will be left for the userspace to handle.
In case the firmware has support for this, drivers can disable this feature
with IEEE80211_HW_NO_STACK_DYNAMIC_PS.
Big thanks to Johannes Berg for the help with the design and code.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Dec 2008 21:35:20 +0000 (23:35 +0200)]
mac80211: track master queue status
This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.
The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 18 Dec 2008 21:35:13 +0000 (23:35 +0200)]
mac80211: enable IEEE80211_CONF_PS only when associated
Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.
iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Thu, 18 Dec 2008 21:13:39 +0000 (22:13 +0100)]
b43: Fix some MAC locking
This fixes some locking w.r.t. the lower MAC (firmware).
It also removes a lot of ancient IRQ-locking that's not needed anymore.
We simply suspend the MAC. That's easier and causes less trouble.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 18 Dec 2008 12:33:00 +0000 (14:33 +0200)]
ath9k: Fixed RX decryption status reporting
The RX code in ath9k uses sc_keymap to figure out whether a default
key was used. However, the default key entries in sc_keymap were
always set and as such, frames could have been claimed to be decrypted
by hardware when they were not. This can cause problems especially
with TKIP since mac80211 is validating the Michael MIC in the frame
and this will result in MIC failure and potentially TKIP
countermeasures if the frame was not decrypted correctly.
Change key cache slot allocation to mark only the keys that really
have been used in sc_keymap to avoid the issue. The key cache slot
selection routines are now internally avoiding the slots that may be
needed for TKIP group keys.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Thu, 18 Dec 2008 12:31:10 +0000 (14:31 +0200)]
ath9k: Fix key cache slot selection for splitmic
ath_reserve_key_cache_slot() was obviously supposed to return an index
to a free slot, not reserved one. This could have caused problems with
hardware revisions that use splitmic.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 17 Dec 2008 20:26:59 +0000 (14:26 -0600)]
mac80211: Print unknown packet type in tasklet_handler
In stress testing p54usb, the WARN_ON() in ieee80211_tasklet_handler() was
triggered; however, there is no logging of the received value for packet
type. Adding that feature will improve the warning.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54usb: bring first generation devices back to life
This patch fixes a serious regression (introduced by:
"p54: fix memory management")
that affected isl3886+net2280 usb devices operation.
Signed-off-by: Christian Lamparter <chunkeey@web.de> Tested-by: Artur Skawina <art.08.09@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Wed, 17 Dec 2008 11:30:31 +0000 (13:30 +0200)]
ath9k: Fix a NULL pointer dereference in ath_rate_get
It looks like mac80211 may try to send unicast frames to a STA that
does not have a STA entry. We need to make sure that that is caught in
the rate control code before dereferencing STA data.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jay Sternberg [Wed, 17 Dec 2008 08:52:34 +0000 (16:52 +0800)]
iwlwifi: indicate txpower is off in sysfs
The patch checks if the radio is disabled before displaying the tx power
level. Previously when the txpower was set off show_tx_power still
returned the prior power level. Now it will indicate the power has been
turned off.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Wed, 17 Dec 2008 08:52:33 +0000 (16:52 +0800)]
iwlwifi: use GFP_KERNEL to allocate Rx SKB memory
Previously we allocate Rx SKB with GFP_ATOMIC flag. This is because we need
to hold a spinlock to protect the two rx_used and rx_free lists operation
in the rxq.
After spliting the rx_used delete and rx_free insert into two operations,
we don't require the skb allocation in an atomic context any more (the
function itself is scheduled in a workqueue).
This patch should fix the "iwlagn: Can not allocate SKB buffers" warning
we see recently.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wu, Fengguang [Wed, 17 Dec 2008 08:52:29 +0000 (16:52 +0800)]
iwlwifi: update comments on the debug interface
Bring up-to-date some comments on the location of debug files.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Winkler, Tomas [Wed, 17 Dec 2008 08:52:27 +0000 (16:52 +0800)]
iwlwifi: cleanup iwl-dev.h
The patch removes unused definition and moves code to proper places.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 15 Dec 2008 14:02:04 +0000 (16:02 +0200)]
ath9k: Remove MAC header pad before reporting TX status
Remove the possible MAC header pad before reporting TX status to
mac80211. This pad is hardware specific operation and should not be
exposed outside the driver. This fixes the frame body in monitor
interfaces that could be used to check on TX status for transmitted
frames.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 15 Dec 2008 13:44:53 +0000 (15:44 +0200)]
ath9k: Fix TX status reporting for retries and MCS index
The count field in struct ieee80211_tx_rate does not include the final
successful attempt, so only report retries here.
Fix the struct ieee80211_tx_rate::idx field when MCS was used. It is
supposed to be the MCS index, not an internal index to the rate
control algorithm table.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Mon, 15 Dec 2008 08:37:50 +0000 (10:37 +0200)]
mac80211: Remove radiotap rate-present flag for HT
Since we do not currently report HT rates (MCS index) in radiotap
header for HT rates, we should not claim the rate is present. The rate
octet itself is used as padding in this case, so only the it_present
flag needs to be removed in case of HT rates.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: Fix crash on unload when using SLUB debug
Reported-by: Hin-Tak Leung <htl10@users.sourceforge.net>
After the code was modified to use urb anchors ("rtl8187: Use usb anchor
facilities to manage urbs"), rtl8187 began generating an intermittent GPF
on shutdown when using SLUB with debugging enabled. Furthermore, rebooting
the system with a ping running caused a GPF every time. There are two problems:
(1) incorrect locking in the rtl8187_rx_cb() routine, a pre-existing bug that
apparently had not been triggered before, and (2) duplicate freeing of receive
skbs that was probably introduced with the change to anchors.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the tx code a bit and will be necessary for
the upcoming stlc45xx<->p54 port.
In detail: we no longer have to tell all back-end drivers directly,
if we want to free a frame right after it was send to the firmware,
or if we do it in the library callback later.
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 14 Dec 2008 00:09:56 +0000 (18:09 -0600)]
rtl8187: Fix error returns
There are two places in the rtl8187 code where a routine was returning zero
(OK) when it should have been returning an error.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54: move statistic timer update routine into a workqueue
This patch moves a good chunk of code from the former statistic update
timer routine into a workqueue, which is kindly provided by mac80211.
Also as a nice side-effect we can lay the foundation for other
essential housekeeping features we want to do in the future.
e.g:
- drain the (clogged) tx_queue.
- initiate bursts.
Signed-off-by: Christian Lamparter <chunkeey@web.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Fri, 12 Dec 2008 16:22:15 +0000 (08:22 -0800)]
iwlagn: fix agn rate scaling
Rate scaling in agn can be broken because of these two problems
1- the LQ command could not sent, we try to call LQ command before
post association will be rejected, this will cause the driver to
break in rs_tx_status reporting initial rate does not match.
2- In rs_rate_init we can get a value of 12, rate 60, for
last_txrate_idx, this rate only valid in SISO/MIMO mode only
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 12 Dec 2008 15:08:31 +0000 (17:08 +0200)]
mac80211: Send Layer 2 Update frame on reassociation
When a STA roams back to the same AP before the previous STA entry has
expired, a new STA entry is not added in mac80211. However, a Layer 2
Update frame still needs to be transmitted to update layer 2 devices
about the new location for the STA. Without this, switches may
continue to forward frames to the previous (now incorrect) port when
STA roams between APs.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k: fix 802.11 header padding on RX, unpadding on TX
Padding the 802.11 header to a multiple of 4 bytes needs to be done only for
frames with a body. This fixes a bug where 2 bytes were missing in monitor
mode for ACK frames. Inspired by a patch from Jouni Malinen on ath9k.
Ref: http://bugzilla.kernel.org/show_bug.cgi?id=12101 : Signed-off-by: Benoit Papillault <benoit.papillault@free.fr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 12 Dec 2008 12:38:34 +0000 (14:38 +0200)]
ath9k: Report HT rates in RX status
Fix and clean up the RX status reporting by getting rid of code that
used internal rate tables and ratekbps calculation. The correct value
is now reported with MCS index instead of the old mechanism that
defaulted to using the highest legacy rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Fri, 12 Dec 2008 12:38:33 +0000 (14:38 +0200)]
mac80211: Add HT rates into RX status reporting
This patch adds option for HT-enabled drivers to report HT rates
(HT20/HT40, short GI, MCS index) to mac80211. These rates are
currently not in the rate table, so the rate_idx is used to indicate
MCS index.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Fri, 12 Dec 2008 06:29:07 +0000 (11:59 +0530)]
ath9k: Do not use association state to update rate table
Now that HT information is made available to the driver through
config() callback, the channel type can be calculated whenever
setting the channel. Update the rate table accordingly with the new
channel type.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Fri, 12 Dec 2008 06:27:43 +0000 (11:57 +0530)]
mac80211: Fix HT channel selection
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Henning Rogge [Thu, 11 Dec 2008 21:04:19 +0000 (22:04 +0100)]
nl80211: Add signal strength and bandwith to nl80211station info
This patch adds signal strength and transmission bitrate
to the station_info of nl80211.
Signed-off-by: Henning Rogge <rogge@fgan.de> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Anton Vorontsov [Thu, 18 Dec 2008 08:23:35 +0000 (08:23 +0000)]
ucc_geth: Remove UGETH_FILTERING dead code
The code appears to be dead: nobody call these functions, plus build
breaks when UGETH_FILTERING is enabled:
ucc_geth.c:1848: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c:1848: warning: its scope is only this definition or declaration, which is probably not what you want
ucc_geth.c: In function 'ugeth_82xx_filtering_get_match_addr_in_hash':
ucc_geth.c:1856: error: dereferencing pointer to incomplete type
ucc_geth.c:1874: error: dereferencing pointer to incomplete type
ucc_geth.c:1877: warning: return from incompatible pointer type
ucc_geth.c: At top level:
ucc_geth.c:1885: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_hash':
ucc_geth.c:1894: error: dereferencing pointer to incomplete type
ucc_geth.c:1909: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1909: warning: assignment from incompatible pointer type
ucc_geth.c:1918: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:1928: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_clear_addr_in_hash':
ucc_geth.c:1947: warning: passing argument 2 of 'ugeth_82xx_filtering_get_match_addr_in_hash' from incompatible pointer type
ucc_geth.c:1947: warning: assignment from incompatible pointer type
ucc_geth.c:1954: error: dereferencing pointer to incomplete type
ucc_geth.c: At top level:
ucc_geth.c:2060: warning: 'struct enet_addr' declared inside parameter list
ucc_geth.c: In function 'ugeth_82xx_filtering_add_addr_in_paddr':
ucc_geth.c:2064: error: dereferencing pointer to incomplete type
ucc_geth.c:2073: error: dereferencing pointer to incomplete type
ucc_geth.c:2075: warning: passing argument 2 of 'hw_add_addr_in_paddr' from incompatible pointer type
make[2]: *** [ucc_geth.o] Error 1
The code is there since the driver was merged, and nobody seem to be
interested in fixing or actually using it. If we ever want the
filtering support, we can always revert the patch and fix it, but so
far it just draws reader's attention.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Thu, 18 Dec 2008 08:23:29 +0000 (08:23 +0000)]
ucc_geth: Fix IRQ freeing code in ucc_geth_open()
open() routine calls stop() in case of errors, the function will try
to free the requested IRQ. But we don't know if it was actually
requested, so the code might issue bogus free_irq(0, dev) call.
Fix this by rearranging the code so that now request_irq() is the last
call in the open() routine, and move free_irq() into the close().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Thu, 18 Dec 2008 08:23:26 +0000 (08:23 +0000)]
ucc_geth: Fix TX watchdog timeout handling
The timeout handling code is currently broken in several ways:
- It calls stop() (which frees all the memory and IRQ), and then
calls startup() (which won't re-request IRQ, neither it will
re-init the Fast UCC structure).
- It calls these routines from the softirq context, which is wrong,
since stop() calls free_irq() (which might sleep) and startup()
allocates things with GFP_KERNEL.
- It won't soft-reset the PHY. We need the PHY reset for at least
MPC8360E-MDS boards with Marvell 88E1111 PHY, the PHY won't recover
from timeouts w/o the reset.
So the patch fixes these problems by implementing the workqueue for the
timeout handling, and there we fully re-open the device via close() and
open() calls. The close/open paths do the right things, and I can see
that the driver actually survive the timeouts.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Vorontsov [Thu, 18 Dec 2008 08:23:22 +0000 (08:23 +0000)]
ucc_geth: Fix endless loop in stop_{tx,rx} routines
Currently the routines wait for the various bits w/o an assumption that
bits may never get set. When timeouts happen I see that these bits never
get set and so the routines hang the kernel.
With this patch we'll wait the graceful stop for 100 ms, and then will
simply exit. There is nothing* we can do about that, but it's OK since
we'll do full reset later.
* Well, actually, there is also not-graceful variant for the TX stop,
but specs says that we never should use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing discard counters for the NIU driver turned out to be more
complicated than first assumed.
The discard counters for the NIU neptune chip are only 16-bit (even
though this is a 64-bit chip). These 16-bit counters can overflow
quickly, especially considering this is a 10Gbit/s ethernet card.
The overflow indication bit is, unfortunatly, not usable as the
counter value does not wrap, but remains at max value 0xFFFF.
Resulting in lost counts until the counter is reset.
The read and reset scheme also poses a problem. Both in theory and in
practice counters can be lost in between reading nr64() and clearing
the counter nw64(). For this reason, the number of counter clearings
nw64() is limited/reduced. On the fast-path the counters are only
syncronized once it exceeds 0x7FFF. When read by userspace, its
syncronized fully.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
Baruch Siach [Fri, 19 Dec 2008 03:39:14 +0000 (19:39 -0800)]
enc28j60: reduce the number of spi transfers in enc28j60_set_bank()
A major source of overhead in the enc28j60 driver is the SPI transfers. Each
SPI transfer entails two kernel thread context switches. One major source of
SPI transfers is the enc28j60_set_bank() functions which runs before every
register access. This patch reduces the number of SPI transfers that
enc28j60_set_bank() performs in two ways:
1. removes unnecessary bank switch for the registers that are present in all
banks
2. when switching from banks 0 or 3 to banks 1 or 2 (i.e. only one bit
changes) enc28j60_set_bank() does only one SPI transfer instead of two
According to my tests these changes reduce the number of SPI transfers in
about 25%.
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Fri, 19 Dec 2008 03:36:46 +0000 (19:36 -0800)]
netdevice zd1201: Use after free
| commit 3d29b0c33d431ecc69ec778f8c236d382f59a85f
| Author: John W. Linville <linville@tuxdriver.com>
| Date: Fri Oct 31 14:13:12 2008 -0400
|
| netdevice zd1201: Convert directly reference of netdev->priv to netdev_priv()
|
| We have some reasons to kill netdev->priv:
| 1. netdev->priv is equal to netdev_priv().
| 2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
| netdev_priv() is more flexible than netdev->priv.
| But we cann't kill netdev->priv, because so many drivers reference to it
| directly.
|
| OK, becasue Dave S. Miller said, "every direct netdev->priv usage is a bug",
| and I want to kill netdev->priv later, I decided to convert all the direct
| reference of netdev->priv first.
|
| (Original patch posted by Wang Chen <wangchen@cn.fujitsu.com> w/ above
| changelog but using dev->ml_priv. That doesn't seem appropriate
| to me for this driver, so I've revamped it to use netdev_priv()
| instead. -- JWL)
This commit changed the allocation of netdev, but didn't change
the free method of it.
This causes "zd" be used after the memory, which is pointed by "zd", being
freed by free_netdev().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Thu, 18 Dec 2008 00:52:00 +0000 (16:52 -0800)]
gianfar: Merge Tx and Rx interrupt for scheduling clean up ring
No clean up function is executed in the interrupt context by this patch.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Thu, 18 Dec 2008 00:51:32 +0000 (16:51 -0800)]
gianfar: Use interface name in interrupt name to distinguish the source.
Interface name (ex. eth0) is used as the prefix for the interrupt name,
with _rx, _tx, and _er appended to distinguish multiple interrupts on
the same interface.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Thu, 18 Dec 2008 00:51:04 +0000 (16:51 -0800)]
gianfar: Add Scatter Gather support
Scatter Gather support in gianfar driver to handle fragmented frames on
the transmit side.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Thu, 18 Dec 2008 00:50:22 +0000 (16:50 -0800)]
gianfar: Fix packet drop when out of memory
The patch which fixed gianfar so it drops packets when it runs out
of memory left in the code which frees the skb when it drops packets.
Change the code so that we only free the skb if the new skb was successfully
created.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phonet: USB CDC Phonet function for gadget framework
This implements the Nokia vendor-specific communication device class
function to exchange Phonet messages over USB. This function is already
found in the "PC suite" USB profile of (non-Linux) Nokia handsets.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Tue, 16 Dec 2008 23:39:48 +0000 (15:39 -0800)]
phylib: Remove unnecessary "reset" fixups in genphy_setup_forced
genphy_setup_forced hasn't actually reset the PHY for a long time,
but a comment to that effect remained in the code, so code continued
to act as if it *had* reset the PHY, and called the necessary fixup
functions to respond to a PHY reset. With no reset, those functions
are no longer needed, so we remove them.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:34:50 +0000 (15:34 -0800)]
gianfar: Make all BD status writes 32-bit
Whenever we want to update the status field in a BD, we usually want to
update the length field, too. By combining them into one 32-bit field, we
reduce the number of stores to memory shared with the controller, and we
eliminate the need for order-enforcement, as the length and "READY" bit are
now updated atomically at the same time.
Signed-off-by: Dai Haruki <Dai.Haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Tue, 16 Dec 2008 23:33:40 +0000 (15:33 -0800)]
gianfar: Add macros for stepping through BDs
This code is based strongly on code from Dai Haruki <Dai.Haruki@freescale.com>.
The gianfar Buffer Descriptors are arranged in a circular array, the end of
which is denoted by setting the "WRAP" bit in the descriptor. However, the
software knows the end of the ring because it knows how many descriptors are
there. Rather than check each descriptor for whether the WRAP bit is set,
use pointer math to determine where the next BD is. This is also useful for
when we want to look at BDs other than the very next one (for Scatter-Gather).
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:32:11 +0000 (15:32 -0800)]
gianfar: Remove unused gfar_add_fcb() function parameter
- Also, use cacheable_memzero instead of memset for performance reasons.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:31:15 +0000 (15:31 -0800)]
gianfar: Enable padding and Optimize the frame prepended bytes handling
The eTSEC can prepend up to 32 bytes to a received frame, usually for the
purpose of aligning the IP address to a word boundary, so this turns it on.
While we're in there, make the handling of the pre-frame bytes (padding and
Frame Control Block) cleaner.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:30:48 +0000 (15:30 -0800)]
gianfar: Fix VLAN HW feature related frame/buffer size calculation.
Optimize the VLAN checking logic as well.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dai Haruki [Tue, 16 Dec 2008 23:30:20 +0000 (15:30 -0800)]
gianfar: Fix eTSEC configuration procedure
Fix some bugs in the ethtool configuration functions:
* gfar_clean_rx_ring should not be called with interrupts disabled.
* Update last transmission time to avoid tx timeout.
* Delete redundant NETIF_F_IP_CSUM check in gfar_start_xmit
* Use netif_tx_lock_bh when reconfiguring the tx csum
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Store the interrupt coalescing values in the form in which they will be
written to the interrupt coalescing registers. This puts a little overhead
into the ethtool configuration, and takes it out of the interrupt handler
Signed-off-by: Dai Haruki <dai.haruki@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Fleming [Tue, 16 Dec 2008 23:29:15 +0000 (15:29 -0800)]
gianfar: Convert gianfar to an of_platform_driver
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Tue, 16 Dec 2008 10:08:29 +0000 (02:08 -0800)]
ipv6: fix the outgoing interface selection order in udpv6_sendmsg()
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Hongyang [Tue, 16 Dec 2008 10:07:45 +0000 (02:07 -0800)]
ipv6: fix the return interface index when get it while no message is received
When get receiving interface index while no message is received,
the the value seted with setsockopt() should be returned.
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
- For the IPV6_PKTINFO option, it will return an in6_pktinfo
structure with ipi6_addr being in6addr_any and ipi6_ifindex being
zero.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log