Speed up memory registration by filling in MTTs directly when the CPU
can write directly to the whole table (all mem-free cards, and to
Tavor mode on 64-bit systems with the patch I posted earlier). This
reduces the number of FW commands needed to register an MR by at least
a factor of 2 and speeds up memory registration significantly.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
IB/mthca: Merge MR and FMR space on 64-bit systems
For Tavor, we currently reserve separate MPT and MTT space for FMRs to
avoid abusing the vmalloc space on 32 bit kernels. No such problem
exists on 64 bit kernels so let's not do it there.
This way we have a shared pool for MR and FMR resources, used on
demand. This will also make it possible to write MTTs for regular
regions directly from driver.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
IB/mthca: Fix access to MTT and MPT tables on non-cache-coherent CPUs
We allocate the MTT table with alloc_pages() and then do pci_map_sg(),
so we must call pci_dma_sync_sg() after the CPU writes to the MTT
table. This works since the device will never write MTTs on mem-free
HCAs, once we get rid of the use of the WRITE_MTT firmware command.
This change is needed to make that work, and is an improvement for
now, since it gives FMRs a chance at working.
For MPTs, both the device and CPU might write there, so we must
allocate DMA coherent memory for these.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
IB/mthca: Give reserved MTTs a separate cache line
MTTs are allocated in non-cache-coherent memory, so we must give
reserved MTTs their own cache line, to prevent both device and
CPU from writing into the same cache line at the same time.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
IB/mthca: Fix reserved MTTs calculation on mem-free HCAs
The reserved_mtts field has different meaning in Tavor and Arbel, so
we are wasting mtt entries on memfree. Fix the Arbel case to match
Tavor semantics.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty [Tue, 30 Jan 2007 00:41:23 +0000 (16:41 -0800)]
RDMA/cma: Increment port number after close to avoid re-use
Randomize the starting port number and avoid re-using port values
immediately after they are closed. Instead keep track of the last
port value used and increment it every time a new port number is
assigned, to better replicate other port spaces.
The following patch adds experimental support for IPoIB connected
mode, as defined by the draft from the IETF ipoib working group. The
idea is to increase performance by increasing the MTU from the maximum
of 2K (theoretically 4K) supported by IPoIB on top of UD. With this
code, I'm able to get 800MByte/sec or more with netperf without
options on a Mellanox 4x back-to-back DDR system.
Some notes on code:
1. SRQ is used for scalability to large cluster sizes
2. Only RC connections are used (UC does not support SRQ now)
3. Retry count is set to 0 since spec draft warns against retries
4. Each connection is used for data transfers in only 1 direction, so
each connection is either active(TX) or passive (RX). 2 sides that
want to communicate create 2 connections.
5. Each active (TX) connection has a separate CQ for send completions -
this keeps the code simple without CQ resize and other tricks
6. To detect stale passive side connections (where the remote side is
down), we keep an LRU list of passive connections (updated once per
second per connection) and destroy a connection after it has been
unused for several seconds. The LRU rule makes it possible to avoid
scanning connections that have recently been active.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Alan [Mon, 5 Feb 2007 16:28:30 +0000 (16:28 +0000)]
libata: Early CFA adapters are not required to support mode setting
If we are doing a PIO setup for a CFA card and it blows up with a device
error then assume it is an older CFA card which doesn't support this
rather than failing the device out of existance.
Stands seperate to the quieting patch but that is obviously useful with
this change.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 6 Feb 2007 00:26:04 +0000 (16:26 -0800)]
sata_nv: propagate ata_pci_device_do_resume return value
ata_pci_device_do_resume can fail if the PCI device couldn't be re-enabled.
Update sata_nv to propagate the return value from this call and to not try
to do any other resume activities if it fails. Fixes a compile warning.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 6 Feb 2007 00:26:03 +0000 (16:26 -0800)]
sata_nv: wait for response on entering/leaving ADMA mode
Update sata_nv to wait for the controller to indicate via the status
register that it has entered the requested state when switching between
ADMA mode and register mode. This issue came up recently when debugging
some problems with cache flush command timeouts and while it didn't appear
to fix that problem, this is something we should likely be doing in any
case.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Tejun Heo <htejun@gmail.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 6 Feb 2007 00:26:02 +0000 (16:26 -0800)]
sata_nv: use ADMA for NODATA commands
Some problems showed up recently with cache flush commands timing out on
sata_nv. Previously these commands were always handled by transitioning to
legacy mode from ADMA mode first. The timeout problem was worked around
already by a change to the interrupt handling code for legacy mode, but for
non-data commands like these it appears we can handle them in ADMA mode, so
the switch to legacy mode is not needed.
This patch changes the behavior so that we use ADMA mode to submit
interrupt-driven commands with ATA_PROT_NODATA protocol. In addition to
avoiding the problem mentioned above entirely, this avoids the overhead of
switching to legacy mode and back to ADMA mode for handling cache flushes.
When handling non-DMA-mapped commands, we leave the APRD blank and clear
the NV_CPB_CTL_APRD_VALID field in the CPB so the controller does not
attempt to read it.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 6 Feb 2007 00:26:01 +0000 (16:26 -0800)]
sata_nv: cleanup ADMA error handling
This cleans up a few issues with the error handling in sata_nv in ADMA mode
to make it more consistent with other NCQ-capable drivers like ahci and
sata_sil24:
- When a command failed, we would effectively set AC_ERR_DEV on the
queued command always. In the case of NCQ commands this prevents libata
from doing a log page query to determine the details of the failed
command, since it thinks we've already analyzed. Just set flags in the
port ehi->err_mask, then freeze or abort and let libata figure out what
went wrong.
- The code handled NV_ADMA_STAT_CPBERR as a "really bad error" which
caused it to set error flags on every queued command. I don't know
exactly what this flag means (no docs, grr!) but from what I can guess
from the standard ADMA spec, it just means that one or more of the CPBs
had an error, so we just need to go through and do our normal checks in
this case.
- In the error_handler function the code would always dump the state of
all the CPBs. This output seems redundant at this point since libata
already dumps the state of all active commands on errors (and it also
triggers at times when it shouldn't, like when suspending). Take this
out.
[akpm@osdl.org: many coding-style fixes] Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Cc: Allen Martin <AMartin@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Mon, 5 Feb 2007 18:08:55 +0000 (21:08 +0300)]
(2.6.20) pata_mpiix: probing cleanup (resend)
MPIIX has only single channel IDE which can be configured for either primary or
secondary legacy I/O ports and IRQ. So, get rid of the unneeded second probe
entry in mpiix_init_one() and of the invalid (but unused anyway) enable bits in
mpiix_pre_reset().
Warning: this cleanup has only been compile-tested...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Mon, 5 Feb 2007 17:24:57 +0000 (20:24 +0300)]
(2.6.20) pata_mpiix: fix PIO setup issues
Fix clearing/setting the wrong TIME/IE/PPE bits for a slave drive caused by a
wrong shift count.
Fix the PIO mode 1 being overclocked by wrongly selecting the fast timing bank.
Also, fix/rephrase some comments while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Mon, 5 Feb 2007 16:45:38 +0000 (19:45 +0300)]
(2.6.20) pata_oldpiix: fix PIO2 underclocking
Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the ata_piix driver does.
Also, fix/rephrase some comments while at it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Fri, 2 Feb 2007 06:29:27 +0000 (15:29 +0900)]
libata: add 150ms between completion of hardreset and status checking
Follow the old SRST rule and delay 150ms between completion of
hardreset and status checking. Debouncing delay should usually cover
this but debounce duration could be shorter than 150ms under certain
circumstances.
Usefulness depends on host controller implementation but it can't hurt
and serves as a reminder that 2s delay for GoVault should also be
added here.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eric D. Mudama [Wed, 31 Jan 2007 06:00:40 +0000 (23:00 -0700)]
libata: rearrange dmesg info to add full ATA revision
Per Jeff's suggestion, this patch rearranges the info printed for ATA
drives into dmesg to add the full ATA firmware revision and model
information, while keeping the output to 2 lines.
Signed-off-by: Eric D. Mudama <edmudama@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sergei Shtylyov [Tue, 30 Jan 2007 17:40:30 +0000 (20:40 +0300)]
pata_sl82c105: wrong assumptions about compatible PIO modes
Fix the wrong "compatible" PIO mode choices: MWDMA0 has 480 ns cycle while PIO1
only has 383 ns cycle, and MWDMA2 timings matchs those of PIO4 exactly.
Andrew Morton [Sat, 3 Feb 2007 02:07:15 +0000 (18:07 -0800)]
git-libata-all: forward declare struct device
In file included from drivers/infiniband/hw/ipath/ipath_diag.c:44:
include/linux/io.h:35: warning: 'struct device' declared inside parameter list
include/linux/io.h:35: warning: its scope is only this definition or declaration
Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 20 Jan 2007 07:00:28 +0000 (16:00 +0900)]
devres: implement pcim_iomap_regions()
Implement pcim_iomap_regions(). This function takes mask of BARs to
request and iomap. No BAR should have length of zero. BARs are
iomapped using pcim_iomap_table().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 20 Jan 2007 07:00:28 +0000 (16:00 +0900)]
libata: update libata LLDs to use devres
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.
As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 20 Jan 2007 07:00:28 +0000 (16:00 +0900)]
libata: update libata core layer to use devres
Update libata core layer to use devres.
* ata_device_add() acquires all resources in managed mode.
* ata_host is allocated as devres associated with ata_host_release.
* Port attached status is handled as devres associated with
ata_host_attach_release().
* Initialization failure and host removal is handedl by releasing
devres group.
* Except for ata_scsi_release() removal, LLD interface remains the
same. Some functions use hacky is_managed test to support both
managed and unmanaged devices. These will go away once all LLDs are
updated to use devres.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 20 Jan 2007 07:00:26 +0000 (16:00 +0900)]
libata: implement ata_host_detach()
Implement ata_host_detach() which calls ata_port_detach() for each
port in the host and export it. ata_port_detach() is now internal and
thus un-exported. ata_host_detach() will be used as the 'deregister
from libata layer' function after devres conversion.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 20 Jan 2007 07:00:26 +0000 (16:00 +0900)]
devres: device resource management
Implement device resource management, in short, devres. A device
driver can allocate arbirary size of devres data which is associated
with a release function. On driver detach, release function is
invoked on the devres data, then, devres data is freed.
devreses are typed by associated release functions. Some devreses are
better represented by single instance of the type while others need
multiple instances sharing the same release function. Both usages are
supported.
devreses can be grouped using devres group such that a device driver
can easily release acquired resources halfway through initialization
or selectively release resources (e.g. resources for port 1 out of 4
ports).
This patch adds devres core including documentation and the following
managed interfaces.
Adrian Bunk [Tue, 30 Jan 2007 08:59:17 +0000 (00:59 -0800)]
fix CONFIG_SATA_SIS=y compile error
Static code shouldn't be used from other modules.
drivers/built-in.o: In function `sis_init_one':
sata_sis.c:(.text+0x7634cd): undefined reference to `sis_info133'
sata_sis.c:(.text+0x7634d6): undefined reference to `sis_info133'
While I was at it, I also moved the prototype of this struct to a header
file.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Mon, 8 Jan 2007 16:11:07 +0000 (16:11 +0000)]
sata_sis: Support for PATA supports
This is quick rework of the patch Uwe proposed but using Kconfig not
ifdefs and user selection to sort out PATA support. Instead of ifdefs and
requiring the user to select both drivers the SATA driver selects the
PATA one.
For neatness I've also moved the extern into the function that uses it.
Signed-off-by: Alan Cox Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 2 Jan 2007 11:20:07 +0000 (20:20 +0900)]
libata: implement HDIO_GET_IDENTITY
'hdparm -I' doesn't work with ATAPI devices and sg_sat is not widely
spread yet leaving no easy way to access ATAPI IDENTIFY data.
Implement HDIO_GET_IDENTITY such that at least 'hdparm -i' works.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 10 Jan 2007 17:13:38 +0000 (17:13 +0000)]
libata: PIIX3 support
This I believe completes the PIIX range of support for libata
This adds the table entries needed for the PIIX3, both a new PCI
identifier and a new mode list. It also fixes an erroneous access to PCI
configuration 0x48 on non UDMA capable chips.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch extends sata_promise to handle ATAPI_NODATA
commands internally. However, commands destined to
ATA_DFLAG_CDB_INTR devices are excluded from this and
continue to be returned to libata.
Concrete changes:
- pdc_atapi_dma_pkt() is renamed to pdc_atapi_pkt(), and is
extended to set up correct headers for NODATA packets
- pdc_qc_prep() calls pdc_atapi_pkt() for ATAPI_NODATA
- pdc_host_intr() handles ATAPI_NODATA
- pdc_qc_issue_prot() sends ATAPI_NODATA packets via the
chip's packet mechanism, except for CDB_INTR devices
Tested on first- and second-generation chips, SATAPI and PATAPI,
with no observable regressions.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_promise: issue ATAPI commands as normal packets
This patch (against libata #upstream + the ATAPI cleanup patch)
reimplements sata_promise's ATAPI support to format ATAPI DMA
commands as normal packets, and to issue them via the hardware's
normal packet machinery.
It turns out that the only reason for issuing ATAPI DMA
commands via the pdc_issue_atapi_pkt_cmd() procedure was to
perform two interrupt-fiddling steps for ATA_DFLAG_CDB_INTR
devices. But these steps aren't needed because sata_promise
sets ATA_FLAG_PIO_POLLING, which disables DMA for those devices.
The remaining steps can easily be done in ATA taskfile packets.
Concrete changes:
- pdc_atapi_dma_pkt() is extended to program all packet setup
steps, and not just contain the CDB; the sequence of steps
exactly mirrors what pdc_issue_atapi_pkt_cmd() did
- pdc_atapi_dma_pkt() needed more parameters: simplify it by
just passing 'qc' and having it extract the data it needs
- pdc_issue_atai_pkt_cmd() and its two helper procedures
pdc_wait_for_drq() and pdc_wait_on_busy() are removed
Tested on first- and second-generation chips, SATAPI and PATAPI,
with no observable regressions.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Here's a cleanup for yesterday's sata_promise ATAPI patch:
- add and use a symbolic constant for the altstatus register
- check return status from ata_busy_wait()
- add missing newline in a warning printk()
- update comment in pdc_issue_atapi_pkt_cmd() to clarify
that the maybe-wait-for-INT issue cannot occur in the
current driver, but may occur if the driver starts issuing
ATAPI non-DMA commands as PDC packets
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 3 Jan 2007 08:32:45 +0000 (17:32 +0900)]
sata_inic162x: finally, driver for initio 162x SATA controllers, take #2
Driver for Initio 162x SATA controllers. ATA r/w, ATAPI r, hotplug
and suspend/resume work. ATAPI w (recording, that is) broken. Feel
free to fix it, but be warned, this controller is weird.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 3 Jan 2007 08:30:39 +0000 (17:30 +0900)]
libata: kill qc->nsect and cursect
libata used two separate sets of variables to record request size and
current offset for ATA and ATAPI. This is confusing and fragile.
This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and
kills them. Also, ata_pio_sector() is updated to use bytes for
qc->cursg_ofs instead of sectors. The field used to be used in bytes
for ATAPI and in sectors for ATA.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 26 Dec 2006 10:39:50 +0000 (19:39 +0900)]
libata: handle pci_enable_device() failure while resuming
Handle pci_enable_device() failure while resuming. This patch kills
the "ignoring return value of 'pci_enable_device'" warning message and
propagates __must_check through ata_pci_device_do_resume().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 2 Jan 2007 11:19:40 +0000 (20:19 +0900)]
libata: use ata_id_c_string()
There were several places where ATA ID strings are manually terminated
and in some places possibly unterminated strings were passed to string
functions which don't limit length like strstr(). This patch converts
all of them over to ata_id_c_string().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Thu, 4 Jan 2007 00:13:57 +0000 (18:13 -0600)]
sata_nv: add suspend/resume support v3 (Resubmit)
Thoughts from Jeff & company on merging the patch below into libata-dev?
This has been in the -mm tree for over a month now, I haven't heard any
complaints about regressions..
Adrian Bunk [Wed, 3 Jan 2007 23:09:36 +0000 (00:09 +0100)]
drivers/ata/: make 4 functions static
This patch makes the following needlessly global functions static:
- libata-core.c: ata_qc_complete_internal()
- libata-scsi.c: ata_scsi_qc_new()
- libata-scsi.c: ata_dump_status()
- libata-scsi.c: ata_to_sense_error()
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Mon, 8 Jan 2007 12:07:25 +0000 (12:07 +0000)]
ahci: Remove jmicron fixup
The AHCI set up is handled properly along with the other bits in the
JMICRON quirk. Remove the code whacking it in ahci.c as its un-needed and
also blindly fiddles with bits it doesn't own.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Mon, 8 Jan 2007 12:10:05 +0000 (12:10 +0000)]
libata-sff: Don't try and activate channels which are not in use
An ATA controller in native mode may have one or more channels disabled
and not assigned resources. In that case the existing code crashes trying
to access I/O ports 0-7.
Add the neccessary check.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_sis: implement laptop list and add ASUS A6K/A6U
In ASUS A6K/A6U hdd is connected to SiS 96x via 40c cable, however it
is short cable and is UDMA66 capable.
tj: fixed if () conditionals
ah: fixed infinite loop
Signed-off-by: Jakub W. Jozwicki <jakub007@go2.pl> Cc: Andreas Henriksson <andreas@fatal.se> Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds ATAPI support to the sata_promise driver.
This has been tested on both first- and second-generation
chips (20378 and 20575), and with both SATAPI and PATAPI
devices. CD-writing works.
SATAPI DMA works on second-generation chips, but on
first-generation chips SATAPI is limited to PIO due
to what appears to be HW limitations.
PATAPI DMA works on both first- and second-generation
chips, but requires the separate PATA support patch
before it can be used on TX2plus chips.
The functional changes to the driver are:
- remove ATA_FLAG_NO_ATAPI from PDC_COMMON_FLAGS
- add ->check_atapi_dma() operation to enable DMA for bulk data
transfers but force PIO for other ATAPI commands; this filter
is from Promise's driver and largely matches pata_pdc207x.c
- use a more restrictive ->check_atapi_dma() on first-generation
chips to force SATAPI to always use PIO
- add handling of ATAPI protocols to pdc_qc_prep(), pdc_host_intr(),
and pdc_qc_issue_prot(): ATAPI_DMA is handled by the driver
while non-DMA protocols are handed over to libata generic code
- add pdc_issue_atapi_pkt_cmd() to handle the initial steps in
issuing ATAPI DMA commands before sending the actual CDB;
this procedure was ported from Promise's driver
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch implements a simple way of setting up per-port
flags on the SATA+PATA Promise TX2plus chips, which is a
prerequisite for supporting the PATA port on those chips.
It is based on the observation that ap->flags isn't really
used until after ->port_start() has been invoked. So it
places the "exceptional" per-port flags array in the driver's
private host structure, and uses it in ->port_start() to
finalise the port's flags.
This patch obsoletes the #promise-sata-pata branch included
in the #all branch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Arjan van de Ven [Tue, 19 Dec 2006 21:05:53 +0000 (13:05 -0800)]
[PATCH] user of the jiffies rounding patch: ATA subsystem
This patch introduces users of the round_jiffies() function: ATA subsystem
This delayed work is of the "about once a second" variety and can be rounded
to coincide with other wakers.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Thu, 7 Dec 2006 16:59:14 +0000 (08:59 -0800)]
[PATCH] pata_it8213: Add new driver for the IT8213 card
Add a driver for the IT8213 which is a single channel ICH-ish PATA
controller. As it is very different to the IT8211/2 it gets its own
driver. There is a legacy drivers/ide driver also available and I'll post
that once I get time to test it all out (probably early January). If
anyone else needs the drivers/ide driver and wants to do the merge for
drivers/ide (Bart ??) then I'll forward it.
[akpm@osdl.org: add PCI ID, constify needed_pio[]] Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Greg Ungerer [Wed, 7 Feb 2007 02:03:08 +0000 (12:03 +1000)]
[PATCH] uclinux: correctly remap bin_fmtflat exe allocated mem regions
remap() the region we get from mmap() to mark the fact that we are
using all of the available slack space. Any slack space is used
to form a simple brk region, and potentially more stack space than
requested at load time.
Any searches of the vma chain may well fail looking for
stack (and especially arg) addresses if the remaping is not done.
The simplest example is /proc/<pid>/cmdline, since the args
are pretty much always at the top of the data/bss/stack region.
Linus Torvalds [Fri, 9 Feb 2007 18:25:38 +0000 (10:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: fix host device registering when nodemgr disabled
ieee1394: video1394: DMA fix
ieee1394: raw1394: prevent unloading of low-level driver
ieee1394: dv1394: tidy up card removal
ieee1394: dv1394: fix CardBus card ejection
ieee1394: sbp2: lower block queue alignment requirement
ieee1394: sbp2: remove bogus "emulated" host flag
ieee1394: save one word in struct hpsb_host
ieee1394: restore config ROM when resuming
ieee1394: ohci1394: drop pcmcia-cs compatibility code
ieee1394: nodemgr: check info_length in ROM header earlier
the scheduled IEEE1394_OUI_DB removal
the scheduled IEEE1394_EXPORT_FULL_API removal
ieee1394: sbp2: use a better wildcard for blacklist
Add PCI class ID for firewire OHCI controllers.
ieee1394: modified csr1212_key_id_type_map to support lisight
Roman Zippel [Thu, 8 Feb 2007 21:48:51 +0000 (22:48 +0100)]
[PATCH] kbuild: more Makefile cleanups
This adds the remaining changes which should have been part of the
review process.
- the define command is inappropriate (it's primarily for rule
definitions)
- execute commands in the current dir as all other commands
- .*.tmp (but not .*.null) files are also removed up by "make clean"
- printf has other side effects, just use "echo -e"
- proper quoting
- proper indentation
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 9 Feb 2007 17:44:28 +0000 (09:44 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-apm
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-apm:
[APM] SH: Convert to use shared APM emulation.
[APM] MIPS: Convert to use shared APM emulation.
[APM] ARM: Convert to use shared APM emulation.
[APM] Add shared version of APM emulation
Roland McGrath [Thu, 8 Feb 2007 22:20:41 +0000 (14:20 -0800)]
[PATCH] Add install_special_mapping
This patch adds a utility function install_special_mapping, for creating a
special vma using a fixed set of preallocated pages as backing, such as for a
vDSO. This consolidates some nearly identical code used for vDSO mapping
reimplemented for different architectures.
Signed-off-by: Roland McGrath <roland@redhat.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] enable mouse button 2+3 emulation for x86 macs
As macbook/macbook pro's also have to live with a single mouse button the
following patch just enables the Macintosh device drivers menu in Kconfig +
adds the macintosh dir to the obj-* to make macbook* users happy (who use
exactly that since months....
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Dmitry Torokhov <dtor@mail.ru> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Thu, 8 Feb 2007 22:20:37 +0000 (14:20 -0800)]
[PATCH] md: avoid possible BUG_ON in md bitmap handling
md/bitmap tracks how many active write requests are pending on blocks
associated with each bit in the bitmap, so that it knows when it can clear
the bit (when count hits zero).
The counter has 14 bits of space, so if there are ever more than 16383, we
cannot cope.
Currently the code just calles BUG_ON as "all" drivers have request queue
limits much smaller than this.
However is seems that some don't. Apparently some multipath configurations
can allow more than 16383 concurrent write requests.
So, in this unlikely situation, instead of calling BUG_ON we now wait
for the count to drop down a bit. This requires a new wait_queue_head,
some waiting code, and a wakeup call.
Tested by limiting the counter to 20 instead of 16383 (writes go a lot slower
in that case...).
Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NeilBrown [Thu, 8 Feb 2007 22:20:30 +0000 (14:20 -0800)]
[PATCH] knfsd: fix a race in closing NFSd connections
If you lose this race, it can iput a socket inode twice and you get a BUG
in fs/inode.c
When I added the option for user-space to close a socket, I added some
cruft to svc_delete_socket so that I could call that function when closing
a socket per user-space request.
This was the wrong thing to do. I should have just set SK_CLOSE and let
normal mechanisms do the work.
Not only wrong, but buggy. The locking is all wrong and it openned up a
race where-by a socket could be closed twice.
So this patch:
Introduces svc_close_socket which sets SK_CLOSE then either leave
the close up to a thread, or calls svc_delete_socket if it can
get SK_BUSY.
Adds a bias to sk_busy which is removed when SK_DEAD is set,
This avoid races around shutting down the socket.
Changes several 'spin_lock' to 'spin_lock_bh' where the _bh
was missing.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neil Brown [Thu, 8 Feb 2007 22:20:29 +0000 (14:20 -0800)]
[PATCH] md: fix various bugs with aligned reads in RAID5
It is possible for raid5 to be sent a bio that is too big for an underlying
device. So if it is a READ that we pass stright down to a device, it will
fail and confuse RAID5.
So in 'chunk_aligned_read' we check that the bio fits within the parameters
for the target device and if it doesn't fit, fall back on reading through
the stripe cache and making lots of one-page requests.
Note that this is the earliest time we can check against the device because
earlier we don't have a lock on the device, so it could change underneath
us.
Also, the code for handling a retry through the cache when a read fails has
not been tested and was badly broken. This patch fixes that code.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: "Kai" <epimetreus@fastmail.fm> Cc: <stable@suse.de> Cc: <org@suse.de> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ken Chen [Thu, 8 Feb 2007 22:20:27 +0000 (14:20 -0800)]
[PATCH] hugetlb: preserve hugetlb pte dirty state
__unmap_hugepage_range() is buggy that it does not preserve dirty state of
huge_pte when unmapping hugepage range. It causes data corruption in the
event of dop_caches being used by sys admin. For example, an application
creates a hugetlb file, modify pages, then unmap it. While leaving the
hugetlb file alive, comes along sys admin doing a "echo 3 >
/proc/sys/vm/drop_caches".
drop_pagecache_sb() will happily free all pages that aren't marked dirty if
there are no active mapping. Later when application remaps the hugetlb
file back and all data are gone, triggering catastrophic flip over on
application.
Not only that, the internal resv_huge_pages count will also get all messed
up. Fix it up by marking page dirty appropriately.
Signed-off-by: Ken Chen <kenchen@google.com> Cc: "Nish Aravamudan" <nish.aravamudan@gmail.com> Cc: Adam Litke <agl@us.ibm.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: <stable@kernel.org> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a fix of regression, which triggered by ~2.6.16.
Patch with name ufs-directory-and-page-cache-from-blocks-to-pages.patch: in
additional to conversation from block to page cache mechanism added new
checks of directory integrity, one of them that directory entry do not
across directory chunks.
But some kinds of UFS: OpenStep UFS and Apple UFS (looks like these are the
same filesystems) have different directory chunk size, then common
UFSes(BSD and Solaris UFS).
So this patch adds ability to works with variable size of directory chunks,
and set it for ufstype=openstep to right size.
Atsushi Nemoto [Thu, 8 Feb 2007 22:20:24 +0000 (14:20 -0800)]
[PATCH] rtc-pcf8563: detect polarity of century bit automatically
The usage of the century bit was inverted on 2.6.19 following to PCF8563's
description, but it was not match to usage suggested by RTC8564's
datasheet. Anyway what MO_C=1 means can vary on each platform. This patch
is to detect its polarity in get_datetime routine. The default value of
c_polarity is 0 (MO_C=1 means 19xx) so that this patch does not change
current behavior even if get_datetime was not called before set_datetime.
Linus Torvalds [Fri, 9 Feb 2007 17:22:36 +0000 (09:22 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-tc:
[EISA] EISA registration with !CONFIG_EISA
[TC] pmagb-b-fb: Convert to the driver model
[TC] dec_esp: Driver model for the PMAZ-A
[TC] mips: pmag-ba-fb: Convert to the driver model
[TC] defxx: TURBOchannel support
[TC] TURBOchannel support for the DECstation
[TC] MIPS: TURBOchannel resources off-by-one fix
[TC] MIPS: TURBOchannel update to the driver model
projects / linux-2.6-omap-h63xx.git / log