Paul Walmsley [Wed, 28 Jan 2009 02:13:12 +0000 (19:13 -0700)]
[ARM] OMAP: Make dpll4_m4_ck programmable with clk_set_rate()
Filling the set_rate and round_rate fields of dpll4_m4_ck makes
this clock programmable through clk_set_rate(). This is needed
to give omapfb control over the dss1_alwon_fck rate.
This patch includes a fix from Tomi Valkeinen <tomi.valkeinen@nokia.com>.
Signed-off-by: Måns Rullgård <mans@mansr.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sergio Aguirre <saaguirre@ti.com> Acked-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Stone <daniel.stone@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:13:02 +0000 (19:13 -0700)]
[ARM] OMAP3 clock: fix 96MHz clocks
Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.
One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses. This patch sticks with the previous setting, which
seems reasonable.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:57 +0000 (19:12 -0700)]
[ARM] OMAP3: move USBHOST SAR handling from clock framework to powerdomain layer
Remove usbhost_sar_fclk from the OMAP3 clock framework. The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state. (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)
In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:50 +0000 (19:12 -0700)]
[ARM] OMAP: Fix sparse, checkpatch warnings in OMAP2/3 PRCM/PM code
Fix sparse & checkpatch warnings in OMAP2/3 PRCM & PM code. This mostly
consists of:
- converting pointer comparisons to integers in form similar to
(ptr == 0) to the standard idiom (!ptr)
- labeling a few non-static private functions as static
- adding prototypes for *_init() functions in the appropriate header
files, and getting rid of the corresponding open-coded extern
prototypes in other C files
- renaming the variable 'sclk' in mach-omap2/clock.c:omap2_get_apll_clkin
to avoid shadowing an earlier declaration
Clean up checkpatch issues. This mostly involves:
- converting some asm/ includes to linux/ includes
- cleaning up some whitespace
- getting rid of braces for conditionals with single following statements
Also take care of a few odds and ends, including:
- getting rid of unlikely() and likely() - none of this code is particularly
fast-path code, so the performance impact seems slim; and some of those
likely() and unlikely() indicators are probably not as accurate as the
ARM's branch predictor
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Walmsley [Wed, 28 Jan 2009 02:12:47 +0000 (19:12 -0700)]
[ARM] OMAP2/3: Add non-CORE DPLL rate set code and M, N programming
Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.
You may see some warnings on rate sets from the freqsel code. The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice. However, the lack of this
freqsel case does not appear to impair the DPLL rate change.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 22 Jan 2009 19:41:20 +0000 (19:41 +0000)]
[ARM] omap: spi: arrange for omap_uwire to use connection ID
... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 22:57:12 +0000 (22:57 +0000)]
[ARM] omap: i2c: remove conditional ick clocks
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 10:26:46 +0000 (10:26 +0000)]
[ARM] omap: mcbsp: convert to use fck/ick clocks directly
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 19 Jan 2009 20:53:30 +0000 (20:53 +0000)]
[ARM] omap: MMC: convert clocks to match by devid and conid
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 23 Jan 2009 22:34:09 +0000 (22:34 +0000)]
[ARM] omap: provide a dummy clock node
By providing a dummy clock node, we can eliminate the SoC conditional
clock handing in the OMAP drivers, moving this knowledge out of the
driver and into the machine clock support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 22 Jan 2009 16:08:04 +0000 (16:08 +0000)]
[ARM] omap: allow double-registering of clocks
This stops things blowing up if a 'struct clk' to be passed more
than once to clk_register(), which will be required when we decouple
struct clk's from their names.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 8 Feb 2009 16:07:46 +0000 (16:07 +0000)]
[ARM] omap: handle RATE_CKCTL via .set_rate/.round_rate methods
It makes no sense to have the CKCTL rate selection implemented as a flag
and a special exception in the top level set_rate/round_rate methods.
Provide CKCTL set_rate/round_rate methods, and use these for where ever
RATE_CKCTL is used and they're not already overridden. This allows us
to remove the RATE_CKCTL flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:44:15 +0000 (13:44 +0000)]
[ARM] omap: move propagate_rate() calls into generic omap clock code
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:07:00 +0000 (13:07 +0000)]
[ARM] omap: remove unnecessary calls to propagate_rate()
We've always called propagate_rate() in the parent function to
the .set_rate methods, so there's no point having the .set_rate
methods also call this heavy-weight function - it's mere
duplication of what's happening elsewhere.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 13 Nov 2008 13:01:32 +0000 (13:01 +0000)]
[ARM] omap: move clock propagation into core omap clock code
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 4 Nov 2008 21:24:00 +0000 (21:24 +0000)]
[ARM] omap: don't use clkops_omap2_dflt_wait for non-ICLK/FCLK clocks
The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers. Specifically, the test is satisfied when these offsets
are used:
If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything. So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 4 Nov 2008 18:59:32 +0000 (18:59 +0000)]
[ARM] omap: eliminate unnecessary conditionals in omap2_clk_wait_ready
Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.
This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 4 Nov 2008 16:48:35 +0000 (16:48 +0000)]
[ARM] omap: kill PARENT_CONTROLS_CLOCK
PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED. This can be handled
in the same way, using clkops_null.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kevin Hilman [Thu, 29 Jan 2009 16:57:18 +0000 (08:57 -0800)]
ARM: OMAP: fix fault in enter_full_retention()
In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.
It's hard to tell where this change was introduced since this file
has been moved and merged.
While this fix prevents a crash, suspend on my n810 is broken with
current kernels. I never come out of suspend.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: Kim Kyuwon <chammoru@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen [Thu, 29 Jan 2009 16:57:17 +0000 (08:57 -0800)]
ARM: OMAP: gptimer min_delta_ns corrected
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com> Reviewed-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: DMA: Fix uninitialized channel flags
This has similar symptoms than 66c23551b1b774e2be3c7bdf91c0ebf2c7a3519e
where just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch
can cause incorrect dump_stack(). Here it can happen if channel has been
used before and the channel flags variable holds old status.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Juha Yrjola [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: Fix race in OMAP2/3 DMA IRQ handling
CSR must be cleared before invoking the callback.
If the callback function starts a new, fast DMA transfer on the same
channel, the completion status might lost if CSR is cleared after
the callback invocation.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Stanley.Miao [Thu, 29 Jan 2009 16:57:12 +0000 (08:57 -0800)]
ARM: OMAP: Fix McBSP spin_lock deadlock
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Wed, 28 Jan 2009 17:01:42 +0000 (09:01 -0800)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info
When there are multiple L1-aliasing userland mappings of the same physical
page, we currently remap each of them uncached, to prevent VIVT cache
aliasing issues. (E.g. writes to one of the mappings not being immediately
visible via another mapping.) However, when we do this remapping, there
could still be stale data in the L2 cache, and an uncached mapping might
bypass L2 and go straight to RAM. This would cause reads from such
mappings to see old data (until the dirty L2 line is eventually evicted.)
This issue is solved by forcing a L2 cache flush whenever the shared page
is made L1 uncacheable.
Ideally, we would make L1 uncacheable and L2 cacheable as L2 is PIPT. But
Feroceon does not support that combination, and the TEX=5 C=0 B=0 encoding
for XSc3 doesn't appear to work in practice.
Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Wed, 28 Jan 2009 16:41:57 +0000 (08:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
Kumar Gala [Wed, 28 Jan 2009 06:07:20 +0000 (00:07 -0600)]
dmi: Fix build breakage
Commit d7b1956fed33d30c4815e848fd7a143722916868 ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMI
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
We just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Anholt [Wed, 28 Jan 2009 05:19:41 +0000 (21:19 -0800)]
drm: Rip out the racy, unused vblank signal code.
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net> Requested-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Russell King [Tue, 27 Jan 2009 23:20:00 +0000 (23:20 +0000)]
[ARM] call undefined instruction exception handler with irqs enabled
Aaro says:
> With spinlock debugs enabled I get might_sleep() warnings when using
> ptrace.
tracked down to a missing enable_irq before calling do_undefinstr().
Reported-by: Aaro Koskinen <aaro.koskinen@nokia.com> Tested-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 27 Jan 2009 22:44:12 +0000 (22:44 +0000)]
[ARM] msm: fix build errors
arch/arm/mach-msm/board-halibut.c:45: error: implicit declaration of function 'MSM_GPIO_TO_INT'
arch/arm/mach-msm/board-halibut.c:45: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:45: error: (near initialization for 'smc91x_resources[1].start')
arch/arm/mach-msm/board-halibut.c:46: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:46: error: (near initialization for 'smc91x_resources[1].end')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gerhard Pircher [Fri, 23 Jan 2009 06:51:28 +0000 (06:51 +0000)]
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Robert Jennings [Thu, 22 Jan 2009 09:40:00 +0000 (09:40 +0000)]
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Casey Schaufler [Wed, 28 Jan 2009 03:56:30 +0000 (19:56 -0800)]
smackfs load append mode fix
Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
Anton Vorontsov [Sat, 10 Jan 2009 02:03:21 +0000 (05:03 +0300)]
USB: Driver for Freescale QUICC Engine USB Host Controller
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: option: add QUANTA HSDPA Data Card device ids
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Phil Dibowitz [Tue, 20 Jan 2009 22:48:36 +0000 (23:48 +0100)]
USB: unusual_dev: usb-storage needs to ignore a device
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>. Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Marcel Sebek [Sun, 28 Dec 2008 13:06:50 +0000 (14:06 +0100)]
USB: 'option' driver - onda device MT503HS has wrong id
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Phil Dibowitz [Sun, 11 Jan 2009 17:46:20 +0000 (18:46 +0100)]
USB: Remove ZTE modem from unusual_devices
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Sat, 20 Dec 2008 19:56:08 +0000 (12:56 -0700)]
USB: usbmon: Implement compat_ioctl
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Brandon Philips [Mon, 5 Jan 2009 16:30:39 +0000 (08:30 -0800)]
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
Andrew Lunn [Tue, 23 Dec 2008 16:31:23 +0000 (17:31 +0100)]
USB: CDC-ACM quirk for MTK GPS
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
James A. Treacy [Sun, 25 Jan 2009 04:37:43 +0000 (23:37 -0500)]
USB: cdc-acm: support some gps data loggers
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bryan Wu [Wed, 7 Jan 2009 16:21:19 +0000 (00:21 +0800)]
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
David Brownell [Mon, 26 Jan 2009 10:05:43 +0000 (02:05 -0800)]
USB: musb: Kconfig fix
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hugo Villeneuve [Sun, 25 Jan 2009 01:57:30 +0000 (17:57 -0800)]
USB: musb cppi bugfixes
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:
drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)
Signed-off-by: Hugo Villeneuve <hugo@hugovil.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6-omap-h63xx.git / log