[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern. The TQM8548_BE requires a further short delay
after writing out a buffer. Normally the R/B pin should be checked, but
it's not connected on the TQM8548_BE. The existing driver uses similar
fixed delay points. To manage these extra delays in a more general way,
I introduced the "fsl,ump-wait-flags" property allowing the board-
specific driver to specify various types of extra delay.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. This requires support for multiple GPIOs for the RNB pins.
The NAND chips are selected through address lines defined by the
FDT property "fsl,upm-addr-line-cs-offsets".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Thomas Gleixner [Wed, 12 Dec 2007 16:27:03 +0000 (17:27 +0100)]
[MTD] [NAND] Add support for 4KiB pages.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Thu, 26 Mar 2009 07:42:50 +0000 (00:42 -0700)]
[MTD] support driver model updates
Follow-on patch to the previous driver model patch for the MTD
framework. This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.
Based on a patch from Kay Sievers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Thu, 26 Mar 2009 07:42:41 +0000 (00:42 -0700)]
[MTD] driver model updates
Update driver model support in the MTD framework, so it fits
better into the current udev-based hotplug framework:
- Each mtd_info now has a device node. MTD drivers should set
the dev.parent field to point to the physical device, before
setting up partitions or otherwise declaring MTDs.
- Those device nodes always map to /sys/class/mtdX device nodes,
which no longer depend on MTD_CHARDEV.
- Those mtdX sysfs nodes have a "starter set" of attributes;
it's not yet sufficient to replace /proc/mtd.
- Enabling MTD_CHARDEV provides /sys/class/mtdXro/ nodes and the
/sys/class/mtd*/dev attributes (for udev, mdev, etc).
- Include a MODULE_ALIAS_CHARDEV_MAJOR macro. It'll work with
udev creating the /dev/mtd* nodes, not just a static rootfs.
So the sysfs structure is pretty much what you'd expect, except
that readonly chardev nodes are a bit quirky.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Uwe Kleine-König [Fri, 27 Mar 2009 23:26:58 +0000 (00:26 +0100)]
[MTD] [NAND] move gen_nand's probe function to .devinit.text
A pointer to plat_nand_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Hamish Moffatt <hamish@cloud.net.au> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Vitaly Wool <vitalywool@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Uwe Kleine-König [Fri, 27 Mar 2009 23:27:03 +0000 (00:27 +0100)]
[MTD] [MAPS] move sa1100 flash's probe function to .devinit.text
A pointer to sa1100_mtd_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Nicolas Pitre <nico@marvell.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Marcin Slusarz [Sat, 28 Mar 2009 17:44:24 +0000 (18:44 +0100)]
[MTD] fix use after free in register_mtd_blktrans
Reported-by: Dan Carpenter <error27@gmail.com> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Benjamin Krill [Fri, 23 Jan 2009 16:18:05 +0000 (17:18 +0100)]
[MTD] ofpart: Check name property to determine partition nodes.
SLOF has a further node which could not be evaluated
by the current routine. The current routine returns
because the node hasn't the required reg property. As
fix this patch adds a check to determine the partition
child nodes. If the node is not a partition the number
of total partitions will be decreased and loop continues
with the next nodes.
Signed-off-by: Benjamin Krill <ben@codiert.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Howells [Fri, 20 Feb 2009 12:31:54 +0000 (12:31 +0000)]
NOMMU: Fix the RomFS Kconfig to ensure at least one backing store is selected
Fix the configuration of the RomFS to make sure that at least one
backing store method is always selected. This is done by rendering it
down to a choice item that selects between Block, MTD and both.
This also works correctly in the case that CONFIG_MTD=m: MTD cannot be
selected as a backing store unless CONFIG_ROMFS_FS is also 'm'.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Howells [Thu, 12 Feb 2009 10:40:10 +0000 (10:40 +0000)]
NOMMU: Make it possible for RomFS to use MTD devices directly
Change RomFS so that it can use MTD devices directly - without the intercession
of the block layer - as well as using block devices.
This permits RomFS:
(1) to use the MTD direct mapping facility available under NOMMU conditions if
the underlying device is directly accessible by the CPU (including XIP);
(2) and thus to be used when the block layer is disabled.
RomFS can be configured with support just for MTD devices, just for Block
devices or for both. If RomFS is configured for both, then it will treat
mtdblock device files as MTD backing stores, not block layer backing stores.
I tested this using a CONFIG_MMU=n CONFIG_BLOCK=n kernel running on my FRV
board with a RomFS image installed on the mtdram test device. I see my test
program being run XIP:
David Howells [Thu, 12 Feb 2009 10:40:05 +0000 (10:40 +0000)]
NOMMU: Add support for direct mapping through mtdconcat if possible
Add support for direct mapping through mtdconcat, if possible, by attaching the
samebacking_dev_info structure to the master.
It has some restrictions:
(1) It won't permit direct mapping of concatenated devices that have differing
BDIs.
(2) It doesn't support maps that span the 'gap' between devices, although it
possibly could if the devices spanned across return compatible
(ie. contiguous) addresses from their get_unmapped_area() ops.
Signed-off-by: Gavin Lambert <gavinl@compacsort.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Bernd Schmidt <bernd.schmidt@analog.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Kyungmin Park [Mon, 17 Nov 2008 08:54:28 +0000 (17:54 +0900)]
[MTD] [OneNAND] Add write-while-program support
OneNAND write-while-program method of writing improves performance,
compared with ordinary writes, by transferring data to OneNAND's
RAM buffers atthe same time as programming the NAND core.
When writing several NAND pages at a time, an improvement of
12% to 25% is seen.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adrian Hunter [Mon, 16 Feb 2009 16:21:35 +0000 (18:21 +0200)]
[MTD] mtdoops: allow MTD selection by name
MTD's have both an index number and a name. Formerly,
the MTD selected for mtdoops was done only by index
number. With this patch, a name can be used instead.
For example, the kernel command line:
console=ttyMTD5
selects MTD 5 for mtdoops. But now this is also possible:
console=ttyMTD,log
which selects the MTD named "log" for mtdoops.
This has the advantage that partitions can be added or
removed that would affect the MTD index number but not the
name, without having to then change the kernel command line.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Acked-by: Richard Purdie <rpurdie@linux.intel.com> Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Rapoport [Tue, 17 Feb 2009 11:54:47 +0000 (13:54 +0200)]
[MTD] [NAND] pxa3xx_nand: add ability to keep controller settings defined by OBM/bootloader
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The nftl module is missing the block-major-93-* alias that would cause
it to be auto-loaded when a nftl of that type is opened. This patch
adds the alias.
Signed-off-by: Scott James Remnant <scott@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[MTD] Auto-load mtdchar module when device opened.
The mtdchar module is missing the char-major-90-* alias that would cause
it to be auto-loaded when a device of that type is opened. This patch
adds the alia..
Signed-off-by: Scott James Remnant <scott@canonical.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Graff Yang [Mon, 2 Mar 2009 08:31:29 +0000 (16:31 +0800)]
[MTD] [CHIPS] cfi_cmdset_0001.c: Fix a bug in inval_cache_and_wait_for_operation().
If the inval_cache_and_wait_for_operation() is re-entered by write operation when erase
operation is in progress, the chip->erase_suspended will be cleared, this cause the erase
timeo is not reset and will result time out error for erase.
Signed-off-by: Graff Yang <graff.yang@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
TXx9 family.
Once upon a time there were tx4925ndfmc and tx4938ndfmc driver. They
were removed due to bitrot in 2005.
This new driver is completely rewritten based on a driver in CELF patch
archive.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Ralf Bächle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Wed, 4 Mar 2009 20:01:41 +0000 (12:01 -0800)]
[MTD] partitioning utility predicates
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a
DaVinci-specific driver to the <linux/mtd/partitions.h> header.
Use those to eliminate #ifdefs in two drivers which had their own
definitions of mtd_has_partitions().
Quite a lot of other MTD drivers could benefit from using use one or both
of these to remove #ifdeffery. Maybe some Janitors would like to help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Wed, 4 Mar 2009 20:01:40 +0000 (12:01 -0800)]
[MTD] we don't need no misc devices
Remove <linux/miscdevice.h> from various drivers which don't actually use
any of its contents. There are still a number of these left in
arch-specific bits of the tree.
(Found by diffing results of "grep -rl" for linux/miscdevice.h and for
misc_register, examining the differences, and verifying removals with a
build test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Kevin Hilman [Wed, 4 Mar 2009 20:01:39 +0000 (12:01 -0800)]
[MTD] [NAND] davinci: drop usage of cpu_is_* macro
Usage of davinci-specific cpu_is macros is not allowed in drivers.
These options should be passed in through platform_data.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Wed, 4 Mar 2009 20:01:38 +0000 (12:01 -0800)]
[MTD] [NAND] fix broken debug messages
Fix incorrect debug messages (*write* not read); someone committed some
cut'n'paste bugs. There might be more, I only noticed these since I was
looking for nand_read usage and landed in some very wrong functions.
IMO all MTD debugging message framework is goofed, anyway. It uses
"DEBUG" in a way that's incompatible with usage most everywhere else in
the kernel, and which prevents normal pr_dbg() and dev_dbg() calls from
working right.
[True. It predates those by a long way, and should probably be updated
to use them. dwmw2]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Wed, 4 Mar 2009 20:01:37 +0000 (12:01 -0800)]
[MTD] [NAND] davinci_nand driver
This is a device driver for the NAND flash controller found on the various
DaVinci family chips. It handles up to four SoC chipselects, and some
flavors of secondary chipselect (e.g. based on upper bits of the address
bus) as used with some multichip packages. (Including the 2 GiB chips
used on some TI devel boards.)
The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but
not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as
available on chips like the DM355 or OMAP-L137 and needed with the more
error-prone MLC NAND chips.
This is a cleaned-up version of code that's been in use for several years
now; sanity checked with the new drivers/mtd/tests.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
David Brownell [Wed, 4 Mar 2009 20:01:36 +0000 (12:01 -0800)]
[MTD] [NAND] fix "raw" reads with ECC syndrome layouts
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data. With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:
Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB. Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.
The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.
Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jeff Moyer [Thu, 19 Mar 2009 00:04:21 +0000 (17:04 -0700)]
aio: lookup_ioctx can return the wrong value when looking up a bogus context
The libaio test harness turned up a problem whereby lookup_ioctx on a
bogus io context was returning the 1 valid io context from the list
(harness/cases/3.p).
Because of that, an extra put_iocontext was done, and when the process
exited, it hit a BUG_ON in the put_iocontext macro called from exit_aio
(since we expect a users count of 1 and instead get 0).
Thanks to Zach for pointing out that hlist_for_each_entry_rcu will not
return with a NULL tpos at the end of the loop, even if the entry was
not found.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Acked-by: Zach Brown <zach.brown@oracle.com> Acked-by: Jens Axboe <jens.axboe@oracle.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davide Libenzi [Thu, 19 Mar 2009 00:04:19 +0000 (17:04 -0700)]
eventfd: remove fput() call from possible IRQ context
Remove a source of fput() call from inside IRQ context. Myself, like Eric,
wasn't able to reproduce an fput() call from IRQ context, but Jeff said he was
able to, with the attached test program. Independently from this, the bug is
conceptually there, so we might be better off fixing it. This patch adds an
optimization similar to the one we already do on ->ki_filp, on ->ki_eventfd.
Playing with ->f_count directly is not pretty in general, but the alternative
here would be to add a brand new delayed fput() infrastructure, that I'm not
sure is worth it.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Cc: Zach Brown <zach.brown@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 19 Mar 2009 21:56:35 +0000 (14:56 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] make page table upgrade work again
[S390] make page table walking more robust
[S390] Dont check for pfn_valid() in uaccess_pt.c
[S390] ftrace/mcount: fix kernel stack backchain
[S390] topology: define SD_MC_INIT to fix performance regression
[S390] __div64_31 broken for CONFIG_MARCH_G5
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: Clear space_info full when adding new devices
Btrfs: Fix locking around adding new space_info
Linus Torvalds [Thu, 19 Mar 2009 18:32:05 +0000 (11:32 -0700)]
Fix race in create_empty_buffers() vs __set_page_dirty_buffers()
Nick Piggin noticed this (very unlikely) race between setting a page
dirty and creating the buffers for it - we need to hold the mapping
private_lock until we've set the page dirty bit in order to make sure
that create_empty_buffers() might not build up a set of buffers without
the dirty bits set when the page is dirty.
I doubt anybody has ever hit this race (and it didn't solve the issue
Nick was looking at), but as Nick says: "Still, it does appear to solve
a real race, which we should close."
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 18 Mar 2009 14:39:11 +0000 (07:39 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Fix vunmap and free order in snd_free_sgbuf_pages()
ALSA: mixart, fix lock imbalance
ALSA: pcm_oss, fix locking typo
ALSA: oss-mixer - Fixes recording gain control
ALSA: hda - Workaround for buggy DMA position on ATI controllers
ALSA: hda - Fix DMA mask for ATI controllers
ALSA: opl3sa2 - Fix NULL dereference when suspending snd_opl3sa2
After TASK_SIZE now gives the current size of the address space the
upgrade of a 64 bit process from 3 to 4 levels of page table needs
to use the arch_mmap_check hook to catch large mmap lengths. The
get_unmapped_area* functions need to check for -ENOMEM from the
arch_get_unmapped_area*, upgrade the page table and retry.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make page table walking on s390 more robust. The current code requires
that the pgd/pud/pmd/pte loop is only done for address ranges that are
below the end address of the last vma of the address space. But this
is not always true, e.g. the generic page table walker does not guarantee
this. Change TASK_SIZE/TASK_SIZE_OF to reflect the current size of the
address space. This makes the generic page table walker happy but it
breaks the upgrade of a 3 level page table to a 4 level page table.
To make the upgrade work again another fix is required.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Gerald Schaefer [Wed, 18 Mar 2009 12:27:35 +0000 (13:27 +0100)]
[S390] Dont check for pfn_valid() in uaccess_pt.c
pfn_valid() actually checks for a valid struct page and not for a
valid pfn. Using xip mappings w/o struct pages, this will result in
-EFAULT returned by the (page table walk) user copy functions,
even though there is valid memory. Those user copy functions don't
need a struct page, so this patch just removes the pfn_valid() check.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Wed, 18 Mar 2009 12:27:33 +0000 (13:27 +0100)]
[S390] topology: define SD_MC_INIT to fix performance regression
The default values for SD_MC_INIT cause an additional cpu usage of up
to 40% on some network benchmarks compared to the plain SD_CPU_INIT
values. So just define SD_MC_INIT to SD_CPU_INIT.
More tuning needs to be done.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The implementation of __div64_31 for G5 machines is broken. The comments
in __div64_31 are correct, only the code does not do what the comments
say. The part "If the remainder has overflown subtract base and increase
the quotient" is only partially realized, the base is subtracted correctly
but the quotient is only increased if the dividend had the last bit set.
Using the correct instruction fixes the problem.
Cc: stable@kernel.org Reported-by: Frans Pop <elendil@planet.nl> Tested-by: Frans Pop <elendil@planet.nl> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Takashi Iwai [Tue, 17 Mar 2009 13:00:06 +0000 (14:00 +0100)]
ALSA: Fix vunmap and free order in snd_free_sgbuf_pages()
In snd_free_sgbuf_pags(), vunmap() is called after releasing the SG
pages, and it causes errors on Xen as Xen manages the pages
differently. Although no significant errors have been reported on
the actual hardware, this order should be fixed other way round,
first vunmap() then free pages.
Cc: Jan Beulich <jbeulich@novell.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Viral Mehta [Tue, 10 Mar 2009 14:43:18 +0000 (15:43 +0100)]
ALSA: oss-mixer - Fixes recording gain control
At the time of initialization, SNDRV_MIXER_OSS_PRESENT_PVOLUME bit is not
set for MIC (slot 7).
So, the same should not be checked when an application tries to do gain
control for audio recording devices.
Just check slot->present for SNDRV_MIXER_OSS_PRESENT_CVOLUME independently.
Verified with a simple application which opens /dev/dsp for recording and
/dev/mixer for volume control.
Takashi Iwai [Tue, 17 Mar 2009 06:49:14 +0000 (07:49 +0100)]
ALSA: hda - Workaround for buggy DMA position on ATI controllers
The position-buffer on ATI controllers are unreliable as well as
on VIA chips, thus the same workaround for DMA position reading as
VIA is useful for ATI.
Takashi Iwai [Tue, 17 Mar 2009 06:47:18 +0000 (07:47 +0100)]
ALSA: hda - Fix DMA mask for ATI controllers
ATI controllers (at least some SB0600 models) appear buggy to handle
64bit DMA. As a workaround, reset GCAP bit0 and let the driver to
use only 32bit DMA on these controllers.
Linus Torvalds [Wed, 18 Mar 2009 03:55:40 +0000 (20:55 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix bb_prealloc_list corruption due to wrong group locking
ext4: fix bogus BUG_ONs in in mballoc code
ext4: Print the find_group_flex() warning only once
ext4: fix header check in ext4_ext_search_right() for deep extent trees.
Masami Hiramatsu [Mon, 16 Mar 2009 22:13:36 +0000 (18:13 -0400)]
module: fix refptr allocation and release order
Impact: fix ref-after-free crash on failed module load
Fix refptr bug: Change refptr allocation and release order not to access a module
data structure pointed by 'mod' after freeing mod->module_core.
This bug will cause kernel panic(e.g. failed to find undefined symbols).
This bug was reported on systemtap bugzilla.
http://sources.redhat.com/bugzilla/show_bug.cgi?id=9927
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com> Cc: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Thomas Bartosik [Mon, 16 Mar 2009 15:04:38 +0000 (16:04 +0100)]
USB: storage: Unusual USB device Prolific 2507 variation added
The "c-enter" USB to Toshiba 1.8" IDE enclosure needs special treatment
to work flawlessly. This patch is absolutely trivial, as the integrated
USB-IDE bridge is already identified to be an "unusual" device, only the
bcdDevice is different (lower) to the bcdDeviceMin already included in
the kernel.
It is a Prolific 2507 bridge.
Dirk Hohndel [Sun, 15 Mar 2009 03:47:39 +0000 (20:47 -0700)]
USB: Add Vendor/Product ID for new CDMA U727 to option driver
* newer versions of the Novatel Wireless U727 CDMA 3G USB stick
have a different Product ID (0x5010); adding this ID makes them
work just fine with the option driver
Signed-off-by: Moritz Muehlenhoff <jmm@debian.org> Tested-by: Jan Heitkoetter <devnull@heitkoetter.net> Cc: stable <stable@kernel.org> Signed-off-by: Phil Dibowitz <phil@ipom.com>
Dan Williams [Thu, 12 Mar 2009 10:53:00 +0000 (06:53 -0400)]
USB: Option: let cdc-acm handle Sony Ericsson F3507g / Dell 5530
The generic cdc-acm driver is now the best one to handle Sony Ericsson
F3507g-based devices (which the Dell 5530 is a rebrand of), now that all
the pieces are in place (ie, cac477e8f1038c41b6f29d3161ce351462ef3df7).
Removing the IDs from option allows cdc-acm to handle the device.
Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 16 Mar 2009 18:21:56 +0000 (14:21 -0400)]
USB: EHCI: expedite unlinks when the root hub is suspended
This patch (as1225) fixes a bug in ehci-hcd. The condition for
whether unlinked QHs can become IDLE should not be that the controller
is halted, but rather that the controller isn't running. In other
words when the root hub is suspended, the hardware doesn't own any
QHs.
This fixes a problem that can show up during hibernation: If a QH is
only partially unlinked when the root hub is frozen, then when the
root hub is thawed the QH won't be in the IDLE state. As a result it
can't be used properly for new URB submissions.
Karsten Wiese [Thu, 26 Feb 2009 00:47:48 +0000 (01:47 +0100)]
USB: EHCI: Fix isochronous URB leak
ehci-hcd uses usb_get_urb() and usb_put_urb() in an unbalanced way causing
isochronous URB's kref.counts incrementing once per usb_submit_urb() call.
The culprit is *usb being set to NULL when usb_put_urb() is called after URB
is given back.
Due to other fixes there is no need for ehci-hcd to deal with usb_get_urb()
nor usb_put_urb() anymore, so patch removes their usages in ehci-hcd.
Patch also makes ehci_to_hcd(ehci)->self.bandwidth_allocated adjust, if a
stream finishes.
Jan Dumon [Tue, 10 Mar 2009 16:29:47 +0000 (17:29 +0100)]
USB: unusual_devs: Add support for GI 0431 SD-Card interface
Enable the SD-Card interface on the GI 0431 HSUPA stick from Option.
The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.
Alan Stern [Mon, 9 Mar 2009 17:44:02 +0000 (13:44 -0400)]
USB: usbfs: keep async URBs until the device file is closed
The usbfs driver manages a list of completed asynchronous URBs. But
it is too eager to free the entries on this list: destroy_async() gets
called whenever an interface is unbound or a device is removed, and it
deallocates the outstanding struct async entries for all URBs on that
interface or device. This is wrong; the user program should be able
to reap an URB any time after it has completed, regardless of whether
or not the interface is still bound or the device is still present.
This patch (as1222) moves the code for deallocating the completed list
entries from destroy_async() to usbdev_release(). The outstanding
entries won't be freed until the user program has closed the device
file, thereby eliminating any possibility that the remaining URBs
might still be reaped.
This fixes a bug in which a program can hang in the USBDEVFS_REAPURB
ioctl when the device is unplugged.
Reported-and-tested-by: Martin Poupe <martin.poupe@upek.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6-omap-h63xx.git / log