Change the "struct slot" that acpiphp uses for managing it's slots to
directly contain the memory for the needed struct hotplug_slot_info and
the slot's name. This way we need only two memory allocations per slot
instead of four.
While we are at it: make_slot_name() is just a wrapper around snprintf()
knowing the right arguments to call it. Since the function makes just one
function call and is only called from one place I inlined it by hand.
Finally this fixes a possible bug waiting for someone to hit it. There were
two unused local variables in acpiphp_register_hotplug_slot(). gcc did not
find them because they were used in memory allocations with sizeof(*var).
They had the same types as the target of the allocation, but nevertheless
this was just weird.
Signed-off-by: Rolf Eike Beer <eike-hotplug@sf-tec.de> Acked-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: switch pci_{enable,disable}_device() to be nestable
Changes the pci_{enable,disable}_device() functions to work in a
nested basis, so that eg, three calls to enable_device() require three
calls to disable_device().
The reason for this is to simplify PCI drivers for
multi-interface/capability devices. These are devices that cram more
than one interface in a single function. A relevant example of that is
the Wireless [USB] Host Controller Interface (similar to EHCI) [see
http://www.intel.com/technology/comms/wusb/whci.htm].
In these kind of devices, multiple interfaces are accessed through a
single bar and IRQ line. For that, the drivers map only the smallest
area of the bar to access their register banks and use shared IRQ
handlers.
However, because the order at which those drivers load cannot be known
ahead of time, the sequence in which the calls to pci_enable_device()
and pci_disable_device() cannot be predicted. Thus:
between steps 3 and 4, driver B would loose access to it's device,
even if it didn't intend to.
By using this modification, the device won't be disabled until all the
callers to enable() have called disable().
This is implemented by replacing 'struct pci_dev->is_enabled' from a
bitfield to an atomic use count. Each caller to enable increments it,
each caller to disable decrements it. When the count increments from 0
to 1, __pci_enable_device() is called to actually enable the
device. When it drops to zero, pci_disable_device() actually does the
disabling.
We keep the backend __pci_enable_device() for pci_default_resume() to
use and also change the sysfs method implementation, so that userspace
enabling/disabling the device doesn't disable it one time too much.
Randy Dunlap [Tue, 17 Oct 2006 17:17:58 +0000 (10:17 -0700)]
pci/i386: style cleanups
Mostly CodingStyle cleanups for arch/i386/pci/i386.c:
- fit in 80 columns;
- use a #defined value instead of an inline constant;
Also change one resource_size_t (DBG) printk from %08lx to %lx since
it can be more than 32 bits (more than 8 hexits).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Thu, 19 Oct 2006 15:41:28 +0000 (09:41 -0600)]
PCI: Block on access to temporarily unavailable pci device
The existing implementation of pci_block_user_cfg_access() was recently
criticised for providing out of date information and for returning errors
on write, which applications won't be expecting.
This reimplementation uses a global wait queue and a bit per device.
I've open-coded prepare_to_wait() / finish_wait() as I could optimise
it significantly by knowing that the pci_lock protected us at all points.
It looked a bit funny to be doing a spin_unlock_irqsave(); schedule(),
so I used spin_lock_irq() for the _user versions of pci_read_config and
pci_write_config. Not carrying a flags pointer around made the code
much less nasty.
Attempts to block an already blocked device hit a BUG() and attempts to
unblock an already unblocked device hit a WARN(). If we need to block
access to a device from userspace, it's because it's unsafe for even
another bit of the kernel to access the device. An attempt to block
a device for a second time means we're about to access the device to
perform some other operation, which could provoke undefined behaviour
from the device.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Acked-by: Adam Belay <abelay@novell.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So it looks like pci aer code will call pci_osc_support_set to tell the
firmware about OSC_EXT_PCI_CONFIG_SUPPORT flag. that causes
ctrlset_buf[OSC_SUPPORT_TYPE] to evaluate to true when pciehp calls
pci_osc_control_set() is called (to attempt to use OSC to gain native
pcie control from firmware), regardless of whether or not _OSC was
actually successfully executed. That causes this section of code:
if (ctrlset_buf[OSC_SUPPORT_TYPE] &&
((global_ctrlsets & ctrlset) != ctrlset)) {
return AE_SUPPORT;
}
to be hit.
This patch will reset the OSC_SUPPORT_TYPE field if _OSC fails, and then
would allow pciehp to go ahead and try to run _OSC again.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
John Keller [Wed, 4 Oct 2006 21:49:52 +0000 (16:49 -0500)]
Altix: Initial ACPI support - ROM shadowing.
Support a shadowed ROM when running with an ACPI capable PROM.
Define a new dev.resource flag IORESOURCE_ROM_BIOS_COPY to
describe the case of a BIOS shadowed ROM, which can then
be used to avoid pci_map_rom() making an unneeded call to
pci_enable_rom().
Signed-off-by: John Keller <jpk@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
John Keller [Wed, 4 Oct 2006 21:49:25 +0000 (16:49 -0500)]
Altix: Add initial ACPI IO support
First phase in introducing ACPI support to SN.
In this phase, when running with an ACPI capable PROM,
the DSDT will define the root busses and all SN nodes
(SGIHUB, SGITIO). An ACPI bus driver will be registered
for the node devices, with the acpi_pci_root_driver being
used for the root busses. An ACPI vendor descriptor is
now used to pass platform specific information for both
nodes and busses, eliminating the need for the current
SAL calls. Also, with ACPI support, SN fixup code is no longer
needed to initiate the PCI bus scans, as the acpi_pci_root_driver
does that.
However, to maintain backward compatibility with non-ACPI capable
PROMs, none of the current 'fixup' code can been deleted, though
much restructuring has been done. For example, the bulk of the code
in io_common.c is relocated code that is now common regardless
of what PROM is running, while io_acpi_init.c and io_init.c contain
routines specific to an ACPI or non ACPI capable PROM respectively.
A new pci bus fixup platform vector has been created to provide
a hook for invoking platform specific bus fixup from pcibios_fixup_bus().
The size of io_space[] has been increased to support systems with
large IO configurations.
Signed-off-by: John Keller <jpk@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 10 Oct 2006 14:01:21 +0000 (08:01 -0600)]
PCI: Replace HAVE_ARCH_PCI_MWI with PCI_DISABLE_MWI
pSeries is the only architecture left using HAVE_ARCH_PCI_MWI and it's
really inappropriate for its needs. It really wants to disable MWI
altogether. So here are a pair of stub implementations for pci_set_mwi
and pci_clear_mwi.
Also rename pci_generic_prep_mwi to pci_set_cacheline_size since that
better reflects what it does.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Cc: Paul Mackerras <paulus@samba.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 10 Oct 2006 14:01:20 +0000 (08:01 -0600)]
PCI: Use pci_generic_prep_mwi on sparc64
The setting of the CACHE_LINE_SIZE register in sparc64's pci
initialisation code isn't quite adequate as the device may have
incompatible requirements. The generic code tests for this, so switch
sparc64 over to using it.
Since sparc64 has different L1 cache line size and PCI cache line size,
it would need to override the generic code like i386 and ia64 do. We
know what the cache line size is at compile time though, so introduce a
new optional constant PCI_CACHE_LINE_BYTES.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: David Miller <davem@davemloft.net> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 10 Oct 2006 14:01:19 +0000 (08:01 -0600)]
PCI: Use pci_generic_prep_mwi on ia64
The pci_generic_prep_mwi() code does everything that pcibios_prep_mwi()
does on ia64. All we need to do is be sure that pci_cache_line_size
is set appropriately, and we can delete pcibios_prep_mwi().
Using SMP_CACHE_BYTES as the default was wrong on uniprocessor machines
as it is only 8 bytes. The default in the generic code of L1_CACHE_BYTES
is at least as good.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Tue, 3 Oct 2006 23:41:26 +0000 (00:41 +0100)]
PCI: quirks: fix the festering mess that claims to handle IDE quirks
The number of permutations of crap we do is amazing and almost all of it
has the wrong effect in 2.6.
At the heart of this is the PCI SFF magic which says that compatibility
mode PCI IDE controllers use ISA IRQ routing and hard coded addresses
not the BAR values. The old quirks variously clears them, sets them,
adjusts them and then IDE ignores the result.
In order to drive all this garbage out and to do it portably we need to
handle the SFF rules directly and properly. Because we know the device
BAR 0-3 are not used in compatibility mode we load them with the values
that are implied (and indeed which many controllers actually
thoughtfully put there in this mode anyway).
This removes special cases in the IDE layer and libata which now knows
that bar 0/1/2/3 always contain the correct address. It means our
resource allocation map is accurate from boot, not "mostly accurate"
after ide is loaded, and it shoots lots of code. There is also lots more
code and magic constant knowledge to shoot once this is in and settled.
Been in my test tree for a while both with drivers/ide and with libata.
Wants some -mm shakedown in case I've missed something dumb or there are
corner cases lurking.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Shouldn't PCI-X state be saved/restored? No device really needs this
right now. qla24xx (fc HBA) and mthca (infiniband) don't do suspend,
and sky2 resets its tweaks when links are brought up.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Francois Romieu [Wed, 29 Nov 2006 21:21:33 +0000 (22:21 +0100)]
[PATCH] r8169: Fix iteration variable sign
This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Milan Svoboda [Wed, 29 Nov 2006 11:09:52 +0000 (12:09 +0100)]
[ARM] 3943/1: share declaration of struct pxa2xx_udc_mach_info between multiple platforms
Move declaration of struct pxa2xx_udc_mach_info from
include/asm-arm/arch-pxa/udc.h to new file
include/asm-arm/mach/udc_pxa2xx.h.
This allow us to use this structure with
multiple platforms - pxa and ixp4xx. USB
device controller used in pxa25x is the same
as controller used in ixp4xx.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patrick McHardy [Wed, 29 Nov 2006 04:10:21 +0000 (20:10 -0800)]
[NETFILTER]: ipt_REJECT: fix memory corruption
On devices with hard_header_len > LL_MAX_HEADER ip_route_me_harder()
reallocates the skb, leading to memory corruption when using the stale
tcph pointer to update the checksum.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 27 Nov 2006 18:26:46 +0000 (10:26 -0800)]
[NETFILTER]: conntrack: fix refcount leak when finding expectation
All users of __{ip,nf}_conntrack_expect_find() don't expect that
it increments the reference count of expectation.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 27 Nov 2006 18:25:59 +0000 (10:25 -0800)]
[NETFILTER]: nf_conntrack: fix the race on assign helper to new conntrack
The found helper cannot be assigned to conntrack after unlocking
nf_conntrack_lock. This tries to find helper to assign again.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 27 Nov 2006 18:25:32 +0000 (10:25 -0800)]
[NETFILTER]: nfctnetlink: assign helper to newly created conntrack
This fixes the bug which doesn't assign helper to newly created
conntrack via nf_conntrack_netlink.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 29 Nov 2006 04:54:40 +0000 (20:54 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: Fixup ata_sas_queuecmd to handle __ata_scsi_queuecmd failure
[PATCH] ahci: AHCI mode SATA patch for Intel ICH9
[PATCH] libata: don't schedule EH on wcache on/off if old EH
Linus Torvalds [Wed, 29 Nov 2006 01:28:41 +0000 (17:28 -0800)]
Merge branch 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Use stricter in process stack check for unwinder
[PATCH] i386: Fix compilation with UP genericarch
[PATCH] x86-64: Fix warning in io_apic.c
[PATCH] x86-64: work around gcc4 issue with -Os in Dwarf2 stack unwind
[PATCH] x86_64: Align data segment to PAGE_SIZE boundary
Linus Torvalds [Wed, 29 Nov 2006 01:27:52 +0000 (17:27 -0800)]
Merge branch 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
[ALSA] version 1.0.13
[ALSA] snd-emu10k1: Fix capture for one variant.
[ALSA] Fix hang-up at disconnection of usb-audio
[ALSA] hda: fix typo for xw4400 PCI sub-ID
[ALSA] hda: fix sigmatel dell system detection
[ALSA] Enable stereo line input for TAS codec
[ALSA] rtctimer: handle RTC interrupts with a tasklet
Joakim Tjernlund [Tue, 28 Nov 2006 23:11:52 +0000 (23:11 +0000)]
[PATCH] Fix Intel/Sharp command set erase suspend bug
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Andi Kleen [Tue, 28 Nov 2006 19:12:59 +0000 (20:12 +0100)]
[PATCH] x86-64: Use stricter in process stack check for unwinder
Previously it would check for alignment only, which could break
if the stack pointer was unaligned. Now explicitely check if the
stack pointer is in the stack page of the current process.
Jan Beulich [Tue, 28 Nov 2006 19:12:59 +0000 (20:12 +0100)]
[PATCH] x86-64: work around gcc4 issue with -Os in Dwarf2 stack unwind
This fixes a problem with gcc4 mis-compiling the stack unwind code under
-Os, which resulted in 'stuck' messages whenever an assembly routine was
encountered.
Matt Porter [Mon, 6 Nov 2006 10:20:38 +0000 (11:20 +0100)]
[ALSA] hda: fix sigmatel dell system detection
Fixes Dell system detection on 9200 codecs. The support
to detect certain Dell machines was merged in the
9205 table where it will be unused on the various Dell
9200-based codec systems. This moves the subsystem IDs
to the correct 9200 table.
Signed-off-by: Matt Porter <mporter@embeddedalley.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Akinobu Mita [Mon, 27 Nov 2006 06:16:48 +0000 (15:16 +0900)]
selinux: fix dentry_open() error check
The return value of dentry_open() shoud be checked by IS_ERR().
Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: James Morris <jmorris@namei.org> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: James Morris <jmorris@namei.org>
Linus Torvalds [Mon, 27 Nov 2006 03:05:22 +0000 (19:05 -0800)]
Fix 'ALIGN()' macro, take 2
You wouldn't think that doing an ALIGN() macro that aligns something up
to a power-of-two boundary would be likely to have bugs, would you?
But hey, in the wonderful world of mixing integer types, you have to be
careful. This just makes sure that the alignment is interpreted in the
same type as the thing to be aligned.
Thanks to Roland Dreier, who noticed that the amso1100 driver got broken
by the previous fix (that just extended the mask to "unsigned long", but
was still broken in "unsigned long long" - it just happened to be the
same on 64-bit architectures).
Acked-by: Roland Dreier <rdreier@cisco.com> Cc: Andrew Morton <akpm@osdl.org> Cc: David Miller <davem@davemloft.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kyle McMartin [Sun, 26 Nov 2006 23:56:56 +0000 (18:56 -0500)]
[PATCH] Fix incorrent type of flags in <asm/semaphore.h>
I still think using BUILD_BUG_ON() is unacceptable, especially given how
vague the error message was.
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
[ And I already removed gthe BUILD_BUG_ON() in the previous commit ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[XFRM] STATE: Fix to respond error to get operation if no matching entry exists.
[NET]: Re-fix of doc-comment in sock.h
[6PACK]: Masking bug in 6pack driver.
[NET]: Fix kfifo_alloc() error check.
[UDP]: Make udp_encap_rcv use pskb_may_pull
[NETFILTER]: H.323 conntrack: fix crash with CONFIG_IP_NF_CT_ACCT
Russell King [Sat, 25 Nov 2006 16:19:23 +0000 (16:19 +0000)]
[ARM] Add PM_LEGACY defaults
Eliminate two warnings:
kernel/power/pm.c:205: warning: 'pm_register' is deprecated (declared at kernel/power/pm.c:64)
kernel/power/pm.c:206: warning: 'pm_send_all' is deprecated (declared at kernel/power/pm.c:180)
by updating defconfig files to contain a sensible PM_LEGACY default.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hans Verkuil [Sat, 25 Nov 2006 12:40:28 +0000 (09:40 -0300)]
V4L/DVB (4885): Improve saa711x check
The old code would accept any device on the same i2c address as the
saa711x chips as an saa711x. However, this fails with saa717x chips,
which use that same address and so are misdetected as a saa7111. Now
check whether the chip is really a saa711x model.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ira Snyder [Mon, 20 Nov 2006 10:20:48 +0000 (07:20 -0300)]
V4L/DVB (4849): Add missing spin_unlock to saa6588 decoder driver
Sparse noticed a lock imbalance in read_from_buf(). Further inspection shows
that the lock should not be held when the function exits.
This adds a spin_unlock_irqrestore(), so that every exit path of the
read_from_buf() function is consistent. The unlock was missing on an error
path.
Signed-off-by: Ira W. Snyder <devel@irasnyder.com> Signed-off-by: Hans J. Koch <koch@hjk-az.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss [Sun, 19 Nov 2006 05:15:37 +0000 (02:15 -0300)]
V4L/DVB (4840): Budget: diseqc_method module parameter for cards with subsystem-id 13c2:1003
New module parameter diseqc_method for cards with subsystem-id 13c2:1003.
- 0: unreliable method, can be used by all board revisions (default)
- 1: reliable method, works for newer board layouts only
The parameter has no effect for cards with other subsystem-ids.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
[XFRM] STATE: Fix to respond error to get operation if no matching entry exists.
When application uses XFRM_MSG_GETSA to get state entry through
netlink socket and kernel has no matching one, the application expects
reply message with error status by kernel.
Kernel doesn't send the message back in the case of Mobile IPv6 route
optimization protocols (i.e. routing header or destination options
header). This is caused by incorrect return code "0" from
net/xfrm/xfrm_user.c(xfrm_user_state_lookup) and it makes kernel skip
to acknowledge at net/netlink/af_netlink.c(netlink_rcv_skb).
This patch fix to reply ESRCH to application.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: TAKAMIYA Noriaki <takamiya@po.ntts.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Bonser [Fri, 24 Nov 2006 01:56:13 +0000 (17:56 -0800)]
[NET]: Re-fix of doc-comment in sock.h
Restoring old, correct comment for sk_filter_release, moving it to
where it should actually be, and changing new comment into proper
comment for sk_filter_rcu_free, where it actually makes sense.
The original fix submitted for this on Oct 23 mistakenly documented
the wrong function.
Signed-off-by: Paul Bonser <misterpib@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jean Delvare [Thu, 23 Nov 2006 19:48:28 +0000 (11:48 -0800)]
[6PACK]: Masking bug in 6pack driver.
Looks like a broken masking to me, binary not is used where bitwise
not was intended.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Olaf Kirch [Thu, 23 Nov 2006 04:11:42 +0000 (20:11 -0800)]
[UDP]: Make udp_encap_rcv use pskb_may_pull
Make udp_encap_rcv use pskb_may_pull
IPsec with NAT-T breaks on some notebooks using the latest e1000 chipset,
when header split is enabled. When receiving sufficiently large packets, the
driver puts everything up to and including the UDP header into the header
portion of the skb, and the rest goes into the paged part. udp_encap_rcv
forgets to use pskb_may_pull, and fails to decapsulate it. Instead, it
passes it up it to the IKE daemon.
Signed-off-by: Olaf Kirch <okir@suse.de> Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Faidon Liambotis [Wed, 22 Nov 2006 05:46:02 +0000 (21:46 -0800)]
[NETFILTER]: H.323 conntrack: fix crash with CONFIG_IP_NF_CT_ACCT
H.323 connection tracking code calls ip_ct_refresh_acct() when
processing RCFs and URQs but passes NULL as the skb.
When CONFIG_IP_NF_CT_ACCT is enabled, the connection tracking core tries
to derefence the skb, which results in an obvious panic.
A similar fix was applied on the SIP connection tracking code some time
ago.
Signed-off-by: Faidon Liambotis <paravoid@debian.org> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Reimplement execvp for our purposes - after we call fork() it is fundamentally
unsafe to use the kernel allocator - current is not valid there. So we simply
pass to our modified execvp() a preallocated buffer. This fixes a real bug
and works very well in testing (I've seen indirectly warning messages from the
forked thread - they went on the pipe connected to its stdout and where read
as a number by UML, when calling read_output(). I verified the obtained
number corresponded to "BUG:").
The added use of __cant_sleep() is not a new bug since __cant_sleep() is
already used in the same function - passing an atomicity parameter would be
better but it would require huge change, stating that this function must not
be called in atomic context and can sleep is a better idea (will make sure of
this gradually).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[akpm@osdl.org: two compile fixes] Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Jiri Kosina <jikos@jikos.cz> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alexey Dobriyan [Sat, 25 Nov 2006 19:09:36 +0000 (11:09 -0800)]
[PATCH] Enforce "unsigned long flags;" when spinlocking
Make it break or warn if you pass to spin_lock_irqsave() and friends
something different from "unsigned long flags;". Suprisingly large amount
of these was caught by recent commit c53421b18f205c5f97c604ae55c6a921f034b0f6 and others.
Idea is largely from FRV typechecking. Suggestions from Andrew Morton.
All stupid typos in first version fixed.
Passes allmodconfig on i386, x86_64, alpha, arm as well as my usual config.
Note #1: checking with sparse is still needed, because a driver can save
and pass around flags or something. So far patch is very intrusive.
Note #2: techically, we should break only if
sizeof(flags) < sizeof(unsigned long),
however, the more pain for getting suspicious code into kernel,
the better.
Jeremy Higdon [Sat, 25 Nov 2006 19:09:33 +0000 (11:09 -0800)]
[PATCH] sgiioc4: Disable module unload
This patch removes a module_exit function that sgiioc4 should not have had.
It seems that the IDE layer doesn't support submodule unloading. sgiioc4 was
the only driver in drivers/ide/pci that had an exit function. After an
unload, the devices would stay around and the next attempt to reference would
crash...
Signed-off-by: Jeremy Higdon <jeremy@sgi.com> Acked-by: "Bartlomiej Zolnierkiewicz" <bzolnier@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roman Zippel [Sat, 25 Nov 2006 19:09:32 +0000 (11:09 -0800)]
[PATCH] fix menuconfig colours with TERM=vt100
On Mon, 13 Nov 2006, Phil Oester wrote:
> In commit 350b5b76384e77bcc58217f00455fdbec5cac594, the default menuconfig
> color scheme was changed to bluetitle. This breaks the highlighting
> of the selected item for me with TERM=vt100. The only way I can see
> which item is selected is via:
>
> make MENUCONFIG_COLOR=mono menuconfig
>
> Which restores the pre-2.6.19 white on black highlighting.
Fix.
Cc: Phil Oester <kernel@linuxace.com> Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Sat, 25 Nov 2006 19:09:28 +0000 (11:09 -0800)]
[PATCH] rtc class locking bugfixes
I got a lockdep warning when running "rtctest" so I though it'd be good
to see what was up.
- The warning was for rtc->irq_task_lock, gotten from rtc_update_irq()
by irq handlerss ... but in a handful of other cases, grabbed without
blocking IRQs.
- Some callers to rtc_update_irq() were not ensuring IRQs were blocked,
yet the routine expects that; make sure all callers block IRQs.
It would appear that RTC API tests haven't been part of anyone's kernel
regression test suite recently, at least not with lockdep running.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Brownell [Sat, 25 Nov 2006 19:09:27 +0000 (11:09 -0800)]
[PATCH] rtc framework handles periodic irqs
The RTC framework has an irq_set_freq() method that should be used to manage
the periodic IRQ frequency, but the current ioctl logic doesn't know how to do
that. This patch teaches it how.
This means that drivers implementing irq_set_freq() will automatically support
RTC_IRQP_{READ,SET} ioctls; that logic doesn't need duplication within the
driver.
[akpm@osdl.org: export rtc_irq_set_freq] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the RTC documentation to summarize the two APIs now available:
the old PC/AT one, and the new RTC class drivers. It also updates the
included "rtctest.c" file to better meet Linux style guidelines, and to work
with the new RTC drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Miklos Szeredi [Sat, 25 Nov 2006 19:09:20 +0000 (11:09 -0800)]
[PATCH] fuse: fix Oops in lookup
Fix bug in certain error paths of lookup routines. The request object was
reused for sending FORGET, which is illegal. This bug could cause an Oops
in 2.6.18. In earlier versions it might silently corrupt memory, but this
is very unlikely.
These error paths are never triggered by libfuse, so this wasn't noticed
even with the 2.6.18 kernel, only with a filesystem using the raw kernel
interface.
Thanks to Russ Cox for the bug report and test filesystem.
projects / linux-2.6-omap-h63xx.git / log