Robert Hancock [Tue, 20 Feb 2007 01:02:46 +0000 (19:02 -0600)]
sata_nv: Cleanup taskfile setup
This edits the taskfile setup to more closely match the way that libata
sends the taskfile for other controllers. This avoids putting taskfile writes
into the CPB buffer that are not needed according to the taskfile flags.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 20 Feb 2007 01:02:27 +0000 (19:02 -0600)]
sata_nv: cleanup CPB and APRD initialization
Clean up the initialization of the CPB and APRD structures so that we
strictly follow the rules for ordering of writes to the CPB flags and
response flags, and prevent duplicate initialization.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 20 Feb 2007 01:01:59 +0000 (19:01 -0600)]
sata_nv: Add CPB register info to error_handler output
When error handling occurs with pending commands, output the contents
of the next CPB count and next CPB index registers as well as the others,
since these may be useful for debugging.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 20 Feb 2007 11:01:53 +0000 (20:01 +0900)]
sata_via: fix resource-managed iomap conversion
Conversion to resource-managed iomap was buggy causing init failures
on both vt6420 and 6421 - BAR5 wasn't mapped for both controllers
while on vt6420 sata_via tried to map BAR0-4 twice. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 20 Feb 2007 09:14:48 +0000 (18:14 +0900)]
libata: disable pdev on all suspend events
libata used disable pdev only on PM_EVENT_SUSPEND while re-enable pdev
unconditionally. This was okay before ref-counted pdev enable update
but it now makes the pdev pinned after swsusp cycle (enabled twice but
disabled only once) and devres sanity check whines about it.
Fix it by unconditionally disabling pdev on all suspend events.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Tue, 20 Feb 2007 00:42:30 +0000 (18:42 -0600)]
sata_nv: delay on switching between NCQ and non-NCQ commands
This patch appears to solve some problems with commands timing out in
cases where an NCQ command is immediately followed by a non-NCQ command
(or possibly vice versa). This is a rather ugly solution, but until we
know more about why this is needed, this is about all we can do.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 17 Feb 2007 17:24:37 +0000 (02:24 +0900)]
libata: fix probe_ent alloc/free bugs
ata_probe_ent_alloc() had a temporary hack such that devm_kzalloc()
was used for allocation if devres had been previously initialized on
the device; otherwise, plain kzalloc() was used. This was to make the
code useable from both the old and devres-aware libata drivers during
transition. This hack made ata_sas_port_alloc() unable to determine
how the probe_ent is allocated, causing double free in some cases.
Remove the now-unneeded hack and make ata_sas_port_alloc() use
devm_kfree().
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Randy Dunlap [Fri, 16 Feb 2007 09:40:06 +0000 (01:40 -0800)]
SATA: use NULL for ptrs
Fix sparse warnings in SATA:
drivers/ata/sata_sil.c:342:9: warning: Using plain integer as NULL pointer
drivers/ata/sata_mv.c:2056:55: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Mon, 12 Feb 2007 00:34:44 +0000 (18:34 -0600)]
sata_nv: add back some verbosity into ADMA error_handler
Some debug output in the ADMA error_handler function was removed recently,
but it may be useful in certain cases, like NCQ commands timing out. Add it
back in, but make it a bit more intelligent so that it only prints if
command(s) are active and only prints the CPBs for those commands.
That way it won't spew at inappropriate times like suspend/resume.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Fri, 16 Feb 2007 09:40:04 +0000 (01:40 -0800)]
SiS warning fixes
Somehow the sis_info133 external definition ended up in libata.h and that
was included by both drivers. However libata.h contains libata-* specific
internals and clashing defines like DRV_NAME so this makes a mess. Move
the extern into the C file and remove the warnings
[akpm@linux-foundation.org: create sis.h to avoid extern-decl-in-C] Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Wed, 7 Feb 2007 16:40:12 +0000 (11:40 -0500)]
libata bugfix: HDIO_DRIVE_TASK
I was trying to use HDIO_DRIVE_TASK for something today,
and discovered that the libata implementation does not copy
over the upper four LBA bits from args[6].
This is serious, as any tools using this ioctl would have their
commands applied to the wrong sectors on the drive, possibly resulting
in disk corruption.
Ideally, newer apps should use SG_IO/ATA_16 directly,
avoiding this bug. But with libata poised to displace drivers/ide,
better compatibility here is a must.
This patch fixes libata to use the upper four LBA bits passed
in from the ioctl.
The original drivers/ide implementation copies over all bits
except for the master/slave select bit. With this patch,
libata will copy only the four high-order LBA bits,
just in case there are assumptions elsewhere in libata (?).
Signed-Off-By: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Fri, 2 Feb 2007 07:22:31 +0000 (16:22 +0900)]
libata: put some intelligence into EH speed down sequence
The current EH speed down code is more of a proof that the EH
framework is capable of adjusting transfer speed in response to error.
This patch puts some intelligence into EH speed down sequence. The
rules are..
* If there have been more than three timeout, HSM violation or
unclassified DEV errors for known supported commands during last 10
mins, NCQ is turned off.
* If there have been more than three timeout or HSM violation for known
supported command, transfer mode is slowed down. If DMA is active,
it is first slowered by one grade (e.g. UDMA133->100). If that
doesn't help, it's slowered to 40c limit (UDMA33). If PIO is
active, it's slowered by one grade first. If that doesn't help,
PIO0 is forced. Note that this rule does not change transfer mode.
DMA is never degraded into PIO by this rule.
* If there have been more than ten ATA bus, timeout, HSM violation or
unclassified device errors for known supported commands && speeding
down DMA mode didn't help, the device is forced into PIO mode. Note
that this rule is considered only for PATA devices and is pretty
difficult to trigger.
One error can only trigger one rule at a time. After a rule is
triggered, error history is cleared such that the next speed down
happens only after some number of errors are accumulated. This makes
sense because now speed down is done in bigger stride.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Fri, 2 Feb 2007 07:22:30 +0000 (16:22 +0900)]
libata: improve ata_down_xfermask_limit()
Make ata_down_xfermask_limit() accept @sel instead of @force_pio0.
@sel selects how the xfermask limit will be adjusted. The following
selectors are defined.
* ATA_DNXFER_PIO : only speed down PIO
* ATA_DNXFER_DMA : only speed down DMA, don't cause transfer mode change
* ATA_DNXFER_40C : apply 40c cable limit
* ATA_DNXFER_FORCE_PIO : force PIO
* ATA_DNXFER_FORCE_PIO0 : force PIO0 (same as original with @force_pio0 == 1)
* ATA_DNXFER_ANY : same as original with @force_pio0 == 0
Currently, only ANY and FORCE_PIO0 are used to maintain the original
behavior. Other selectors will be used later to improve EH speed down
sequence.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Akira Iguchi [Fri, 26 Jan 2007 07:28:18 +0000 (16:28 +0900)]
libata: PATA driver for Celleb
This is the patch for PATA controller of Celleb.
This driver uses the managed iomap (devres).
Because this driver needs special taskfile accesses, there is
a copy of ata_std_softreset(). ata_dev_try_classify() is exported
so that it can be used in this function.
WARNING: drivers/video/i810/i810fb.o - Section mismatch: reference
to .init.data: from .text between 'i810_check_params' (at offset
0x1123) and 'encode_fix'
yres cannot be declared __devinitdata as it is used in
i810_check_params(), which isn't __devinit.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 20 Feb 2007 21:58:21 +0000 (13:58 -0800)]
[PATCH] fb: SM501 framebuffer driver
Driver for the Silicon Motion SM501 multifunction device framebuffer
subsystem.
This driver supports both the CRT and LCD panel heads, with some simple
acceleration for the cursor plotting and support for screen panning. There
is no current support for bitblt/drawing engines, which should be added at
a later date.
This has been tested on a number of configurations, including PCI and
generic-bus, on PPC, ARM and SH4
[akpm@linux-foundation.org: fix warnings] Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Vincent Sanders <vince@arm.linux.org.u.> Acked-by: James Simmons <jsimmons@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Zabel [Tue, 20 Feb 2007 21:58:20 +0000 (13:58 -0800)]
[PATCH] GPIO API: SA1100 wrapper cleanup
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/241),
this patch
- adds gpio_direction_input/output functions to
generic.c instead of making them inline,
- fixes comment and includes and uses inline functions
instead of macros in gpio.h
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Zabel [Tue, 20 Feb 2007 21:58:20 +0000 (13:58 -0800)]
[PATCH] GPIO API: S3C2410 wrapper cleanup
this one adds an #include <asm/arch/regs-gpio.h>.
Tested by Roman Moravcik on s3c2440.
Based on the discussion last december
(http://lkml.org/lkml/2006/12/20/243), this patch
- fixes comment and includes in gpio.h
- adds the gpio_to_irq definition for S3C2400
- includes asm/arch/regs-gpio.h for pin direction
definitions
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harald Welte [Tue, 20 Feb 2007 21:58:19 +0000 (13:58 -0800)]
[PATCH] spi_s3c2410_gpio.c spi mode 2 and 3 support
Add transfer modes 2 and 3 to the S3C24XX gpio SPI driver
Signed-off-by: Harald Welte <laforge@openmoko.org> Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 20 Feb 2007 21:58:19 +0000 (13:58 -0800)]
[PATCH] SPI controller build/warning fixes
The signature of the per-device cleanup() routine changed to remove its
const-ness. Three new SPI controller drivers now need that change, to
eliminate build warnings.
This also fixes a build bug with atmel_spi on AT91 systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: drivers/parport/parport_pc.o - Section mismatch: reference
to .init.text: from .text between 'parport_pc_probe_port' (at offset
0x14f7) and 'parport_pc_unregister_port'
parport_dma_probe() cannot be declared __devinit as it is called
from parport_pc_probe_port() which isn't.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Tue, 20 Feb 2007 21:58:18 +0000 (13:58 -0800)]
[PATCH] lockdep: annotate BLKPG_DEL_PARTITION
>=============================================
>[ INFO: possible recursive locking detected ]
>2.6.19-1.2909.fc7 #1
>---------------------------------------------
>anaconda/587 is trying to acquire lock:
> (&bdev->bd_mutex){--..}, at: [<c05fb380>] mutex_lock+0x21/0x24
>
>but task is already holding lock:
> (&bdev->bd_mutex){--..}, at: [<c05fb380>] mutex_lock+0x21/0x24
>
>other info that might help us debug this:
>1 lock held by anaconda/587:
> #0: (&bdev->bd_mutex){--..}, at: [<c05fb380>] mutex_lock+0x21/0x24
>
>stack backtrace:
> [<c0405812>] show_trace_log_lvl+0x1a/0x2f
> [<c0405db2>] show_trace+0x12/0x14
> [<c0405e36>] dump_stack+0x16/0x18
> [<c043bd84>] __lock_acquire+0x116/0xa09
> [<c043c960>] lock_acquire+0x56/0x6f
> [<c05fb1fa>] __mutex_lock_slowpath+0xe5/0x24a
> [<c05fb380>] mutex_lock+0x21/0x24
> [<c04d82fb>] blkdev_ioctl+0x600/0x76d
> [<c04946b1>] block_ioctl+0x1b/0x1f
> [<c047ed5a>] do_ioctl+0x22/0x68
> [<c047eff2>] vfs_ioctl+0x252/0x265
> [<c047f04e>] sys_ioctl+0x49/0x63
> [<c0404070>] syscall_call+0x7/0xb
Annotate BLKPG_DEL_PARTITION's bd_mutex locking and add a little comment
clarifying the bd_mutex locking, because I confused myself and initially
thought the lock order was wrong too.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Tue, 20 Feb 2007 21:58:17 +0000 (13:58 -0800)]
[PATCH] drivers/isdn/gigaset/: build asyncdata.o into the gigaset module
LD drivers/isdn/gigaset/built-in.o
drivers/isdn/gigaset/ser_gigaset.o: In function `gigaset_m10x_send_skb':
(.text+0xe50): multiple definition of `gigaset_m10x_send_skb'
drivers/isdn/gigaset/usb_gigaset.o:(.text+0x0): first defined here
drivers/isdn/gigaset/ser_gigaset.o: In function `gigaset_m10x_input':
(.text+0x1121): multiple definition of `gigaset_m10x_input'
drivers/isdn/gigaset/usb_gigaset.o:(.text+0x2d1): first defined here
make[4]: *** [drivers/isdn/gigaset/built-in.o] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Tilman Schmidt <tilman@imap.cc> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 20 Feb 2007 21:58:16 +0000 (13:58 -0800)]
[PATCH] remove modpost false warnings on ARM
This patch stops "modpost" from issuing erroneous modpost warnings on ARM
builds, which it's been doing since since maybe last summer. A canonical
example would be driver method table entries:
WARNING: <path> - Section mismatch: reference to .exit.text:<name>_remove
from .data after '$d' (at offset 0x4)
That "$d" symbol is generated by tools conformant with ARM ABI specs; in
this case it's a symbol **in the middle of** a "<name>_driver" struct.
The erroneous warnings appear to be issued because "modpost" whitelists
references from "<name>_driver" data into init and exit sections ... but
doesn't know should also include those "$d" mapping symbols, which are not
otherwise associated with "<name>_driver" symbols.
This patch prevents the modpost symbol lookup code from ever returning
those mapping symbols, so it will return a whitelisted symbol instead.
Then things work as expected.
Now to revert various code-bloating "fixes" that got merged because of this
modpost bug....
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Roman Zippel <zippel@linux-m68k.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Zabel [Tue, 20 Feb 2007 21:58:15 +0000 (13:58 -0800)]
[PATCH] GPIO API: PXA wrapper cleanup
Based on the discussion last december (http://lkml.org/lkml/2006/12/20/242),
this patch:
- moves the PXA_LAST_GPIO check into pxa_gpio_mode
- fixes comment and includes in gpio.h
- replaces the gpio_set/get_value macros with inline
functions and adds a non-inline version to avoid
code explosion when gpio is not a constant.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Nicolas Pitre <nico@cam.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 20 Feb 2007 21:58:14 +0000 (13:58 -0800)]
[PATCH] at91_rtc updates
Various bug fixes to the at91rm9200 RTC:
- alarm: setalarm() should pay attention to the "enabled" flag
- init: cleaner handling of the wakeup flags, which cpu init should
really have set up. Doing it here is just a workaround.
- linkage: since the at91_rtc driver probe() routine is in the init
section, it should use platform_driver_probe() instead of leaving
that pointer around in the driver struct after init section removal.
- linkage: likewise, remove() belongs in the exit section.
Among other things, the init and alarm changes ensure that this driver
handles the new sysfs "wakealarm" attribute properly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Tue, 20 Feb 2007 21:58:13 +0000 (13:58 -0800)]
[PATCH] rtc-sa1100 rtc_wklarm.enabled bugfixes
Some rtc-sa1100 bugfixes:
- The read_alarm() method reports the rtc_wkalrm.enabled field properly.
This patch is already in the handhelds.org tree.
- And the set_alarm() method now handles that flag correctly, rather than
making mismatched {en,dis}able_irq_wake() calls, which trigger runtime
warning messages. (Those calls are best made in suspend/resume methods.)
Note that while this SA1100/PXA RTC is fully capable of waking those ARM
processors from sleep states, that mechanism isn't properly supported on
either processor family, or in this driver. Some boards have board-specific
PM glue providing partial workarounds for the weak generic PM support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] Missing __user in pointer referenced within copy_from_user
Pointers to user data should be marked with a __user hint. This one is
missing.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:58:12 +0000 (13:58 -0800)]
[PATCH] genalloc warning fixes
lib/genalloc.c: In function 'gen_pool_alloc':
lib/genalloc.c:151: warning: passing argument 2 of '__set_bit' from incompatible pointer type
lib/genalloc.c: In function 'gen_pool_free':
lib/genalloc.c:190: warning: passing argument 2 of '__clear_bit' from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
affs wants to truncate the inode when the last user goes away, currently it
does that through a potentially racy i_count check in ->put_inode. But we
already have a method that's called just after the we dropped the last
reference, ->drop_inode. This patch implements affs_drop_inode to take
advantage of this.
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Tue, 20 Feb 2007 21:58:10 +0000 (13:58 -0800)]
[PATCH] autofs4: check for directory re-create in lookup
This problem was identified and fixed some time ago by Jeff Moyer but it fell
through the cracks somehow.
It is possible that a user space application could remove and re-create a
directory during a request. To avoid returning a failure from lookup
incorrectly when our current dentry is unhashed we need to check if another
positive, hashed dentry matching this one exists and if so return it instead
of a fail.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Tue, 20 Feb 2007 21:58:10 +0000 (13:58 -0800)]
[PATCH] autofs4: fix another race between mount and expire
Jeff Moyer has identified a race between mount and expire.
What happens is that during an expire the situation can arise that a directory
is removed and another lookup is done before the expire issues a completion
status to the kernel module. In this case, since the the lookup gets a new
dentry, it doesn't know that there is an expire in progress and when it posts
its mount request, matches the existing expire request and waits for its
completion. ENOENT is then returned to user space from lookup (as the dentry
passed in is now unhashed) without having performed the mount request.
The solution used here is to keep track of dentrys in this unhashed state and
reuse them, if possible, in order to preserve the flags. Additionally, this
infrastructure will provide the framework for the reintroduction of caching of
mount fails removed earlier in development.
Signed-off-by: Ian Kent <raven@themaw.net> Acked-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ian Kent [Tue, 20 Feb 2007 21:58:09 +0000 (13:58 -0800)]
[PATCH] autofs4: header file update
The current header file definitions for autofs version 5 have caused a couple
of problems for application builds downstream.
This fixes the problem by separating the definitions.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Tue, 20 Feb 2007 21:58:09 +0000 (13:58 -0800)]
[PATCH] fs: fix nobh data leak
nobh_prepare_write leaks data similarly to how simple_prepare_write did. Fix
by not marking the page uptodate until nobh_commit_write time. Again, this
could break weird use-cases, but none appear to exist in the tree.
We can safely remove the set_page_dirty, because as the comment says,
nobh_commit_write does set_page_dirty. If a filesystem wants to allocate
backing store for a page dirtied via mmap, page_mkwrite is the suggested
approach.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Tue, 20 Feb 2007 21:58:08 +0000 (13:58 -0800)]
[PATCH] fs: fix libfs data leak
simple_prepare_write leaks uninitialised kernel data. This happens because
the it leaves an uninitialised "hole" over the part of the page that the
write is expected to go to. This is fine, but it then marks the page
uptodate, which means a concurrent read can come in and copy the
uninitialised memory into userspace before it written to.
Fix it by simply marking it uptodate in simple_commit_write instead, after
the hole has been filled in. This could theoretically break an fs that
uses simple_prepare_write and not simple_commit_write, and that relies on
the incorrect simple_prepare_write behaviour. Luckily, none of those
exists in the tree.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jones [Tue, 20 Feb 2007 21:58:07 +0000 (13:58 -0800)]
[PATCH] loosen dependancy on rtc cmos
This option is useful for all of the X86 subarchs afaik (and especially
X86_GENERICARCH).
Signed-off-by: Dave Jones <davej@redhat.com> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 20 Feb 2007 21:58:01 +0000 (13:58 -0800)]
[PATCH] mfd: SM501 core driver
This driver provides the core functionality of the SM501, which is a
multi-function chip including two framebuffers, video acceleration, USB,
and many other peripheral blocks.
The driver exports a number of entries for the peripheral drivers to use.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Miguel Ojeda [Tue, 20 Feb 2007 21:58:00 +0000 (13:58 -0800)]
[PATCH] cfag12864b: fix crash when built-in and no parport present
The problem comes when ks0108/cfag12864b are built-in and no parallel port is
present. ks0108_init() is called first, as it should be, but fails to load
(as there is no parallel port to use).
After that, cfag12864b_init() gets called, without knowing anything about
ks0108 failed, and calls ks0108_writecontrol(), which dereferences an
uninitialized pointer.
Init order is OK, I think. The problem is how to stop cfag12864b_init() being
called if ks0108 failed to load. modprobe does it for us, but, how when
built-in?
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Tue, 20 Feb 2007 21:57:56 +0000 (13:57 -0800)]
[PATCH] fault injection: split up stacktrace filter Kconfig option
There is no prompt for CONFIG_STACKTRACE, so FAULT_INJECTION cannot be
selected without LOCKDEP enabled. (found by Paolo 'Blaisorblade'
Giarrusso)
In order to fix such broken Kconfig dependency, this patch splits up the
stacktrace filter support for fault injection by new Kconfig option, which
enables to use fault injection on the architecture which doesn't have
general stacktrace support.
Cc: "Paolo 'Blaisorblade' Giarrusso" <blaisorblade@yahoo.it> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Srinivasa Ds [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] kprobes: list all active probes in the system
This patch lists all active probes in the system by scanning through
kprobe_table[]. It takes care of aggregate handlers and prints the type of
the probe. Letter "k" for kprobes, "j" for jprobes, "r" for kretprobes.
It also lists address of the instruction,its symbolic name(function name +
offset) and the module name. One can access this file through
/sys/kernel/debug/kprobes/list.
Output looks like this
=====================
llm40:~/a # cat /sys/kernel/debug/kprobes/list c0169ae3 r sys_read+0x0 c0169ae3 k sys_read+0x0 c01694c8 k vfs_write+0x0 c0167d20 r sys_open+0x0 f8e658a6 k reiserfs_delete_inode+0x0 reiserfs c0120f4a k do_fork+0x0 c0120f4a j do_fork+0x0 c0169b4a r sys_write+0x0 c0169b4a k sys_write+0x0 c0169622 r vfs_read+0x0
=================================
[akpm@linux-foundation.org: cleanup]
[ananth@in.ibm.com: sparc build fix] Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com> Cc: Prasanna S Panchamukhi <prasanna@in.ibm.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com> Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Tue, 20 Feb 2007 21:57:54 +0000 (13:57 -0800)]
[PATCH] fs: fix __block_write_full_page error case buffer submission
Andrew noticed that unlocking the page before submitting all buffers for
writeout could cause problems if the IO completes before we've finished
messing around with the page buffers, and they subsequently get freed.
Even if there were no bug, it is a good idea to bring the error case
into line with the common case here.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] shm: make sysv ipc shared memory use stacked files
The current ipc shared memory code runs into several problems because it
does not quite use files like the rest of the kernel. With the option of
backing ipc shared memory with either hugetlbfs or ordinary shared memory
the problems got worse. With the added support for ipc namespaces things
behaved so unexpected that we now have several bad namespace reference
counting bugs when using what appears at first glance to be a reasonable
idiom.
So to attack these problems and hopefully make the code more maintainable
this patch simply uses the files provided by other parts of the kernel and
builds it's own files out of them. The shm files are allocated in do_shmat
and freed when their reference count drops to zero with their last unmap.
The file and vm operations that we don't want to implement or we don't
implement completely we just delegate to the operations of our backing
file.
This means that we now get an accurate shm_nattch count for we have a
hugetlbfs inode for backing store, and the shm accounting of last attach
and last detach time work as well.
This means that getting a reference to the ipc namespace when we create the
file and dropping the referenece in the release method is now safe and
correct.
This means we no longer need a special case for clearing VM_MAYWRITE
as our file descriptor now only has write permissions when we have
requested write access when calling shmat. Although VM_SHARED is now
cleared as well which I believe is harmless and is mostly likely a
minor bug fix.
By using the same set of operations for both the hugetlb case and regular
shared memory case shmdt is not simplified and made slightly more correct
as now the test "vma->vm_ops == &shm_vm_ops" is 100% accurate in spotting
all shared memory regions generated from sysvipc shared memory.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] slab: reduce size of alien cache to cover only possible nodes
The alien cache is a per cpu per node array allocated for every slab on the
system. Currently we size this array for all nodes that the kernel does
support. For IA64 this is 1024 nodes. So we allocate an array with 1024
objects even if we only boot a system with 4 nodes.
This patch uses "nr_node_ids" to determine the number of possible nodes
supported by a hardware configuration and only allocates an alien cache
sized for possible nodes.
The initialization of nr_node_ids occurred too late relative to the bootstrap
of the slab allocator and so I moved the setup_nr_node_ids() into
free_area_init_nodes().
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] Convert highest_possible_processor_id to nr_cpu_ids
We frequently need the maximum number of possible processors in order to
allocate arrays for all processors. So far this was done using
highest_possible_processor_id(). However, we do need the number of
processors not the highest id. Moreover the number was so far dynamically
calculated on each invokation. The number of possible processors does not
change when the system is running. We can therefore calculate that number
once.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Frederik Deweerdt <frederik.deweerdt@gmail.com> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] Replace highest_possible_node_id() with nr_node_ids
highest_possible_node_id() is currently used to calculate the last possible
node idso that the network subsystem can figure out how to size per node
arrays.
I think having the ability to determine the maximum amount of nodes in a
system at runtime is useful but then we should name this entry
correspondingly, it should return the number of node_ids, and the the value
needs to be setup only once on bootup. The node_possible_map does not
change after bootup.
This patch introduces nr_node_ids and replaces the use of
highest_possible_node_id(). nr_node_ids is calculated on bootup when the
page allocators pagesets are initialized.
[deweerdt@free.fr: fix oops] Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] fix mempolicy's check on a system with memory-less-node
bind_zonelist() can create zero-length zonelist if there is a
memory-less-node. This patch checks the length of zonelist. If length is
0, returns -EINVAL.
tested on ia64/NUMA with memory-less-node.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Acked-by: Andi Kleen <ak@suse.de> Cc: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 20 Feb 2007 21:57:48 +0000 (13:57 -0800)]
[PATCH] rework reserved major handling
Several people have reported failures in dynamic major device number handling
due to the recent changes in there to avoid handing out the local/experimental
majors.
Rolf reports that this is due to a gcc-4.1.0 bug.
The patch refactors that code a lot in an attempt to provoke the compiler into
behaving.
Andries Brouwer [Tue, 20 Feb 2007 21:57:47 +0000 (13:57 -0800)]
[PATCH] minix v3: fix superblock definition
Somehow we got the layout of the v3 superblock wrong, which causes crashes due
to overindexing of the buffer_head array in statfs on large fielsystems.
Linus Torvalds [Tue, 20 Feb 2007 18:26:46 +0000 (10:26 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (21 commits)
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
natsemi: Add support for using MII port with no PHY
skge: race with workq and RTNL
Replace local random function with random32()
s2io: RTNL and flush_scheduled_work deadlock
8139too: RTNL and flush_scheduled_work deadlock
sis190: RTNL and flush_scheduled_work deadlock
r8169: RTNL and flush_scheduled_work deadlock
[PATCH] ieee80211softmac: Fix setting of initial transmit rates
[PATCH] bcm43xx: OFDM fix for rev 1 cards
[PATCH] bcm43xx: Fix for 4311 and 02/07/07 specification changes
[PATCH] prism54: correct assignment of DOT1XENABLE in WE-19 codepaths
[PATCH] zd1211rw: Readd zd_addr_t cast
[PATCH] bcm43xx: Fix for oops on resume
[PATCH] bcm43xx: Ignore ampdu status reports
[PATCH] wavelan: Use ARRAY_SIZE macro when appropriate
[PATCH] hostap: Use ARRAY_SIZE macro when appropriate
[PATCH] misc-wireless: Use ARRAY_SIZE macro when appropriate
[PATCH] ipw2100: Use ARRAY_SIZE macro when appropriate
[PATCH] bcm43xx: Janitorial change - remove two unused variables
...
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[PATCH] ARM: fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 20 Feb 2007 18:14:29 +0000 (10:14 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[NET] Eliminate user-selectable CONFIG_MV643XX_ETH_[012]
[MIPS] Drop __init from init_8259A()
[MIPS] Fix Kconfig typo bug
[MIPS] Fix double signal on trap and break instruction
[MIPS] sigset_32 has been made redundand by compat_sigset_t.
[MIPS] emma2rh: Remove needless <asm/i8259.h> inclusion.
[MIPS] Add MTD device support for Cobalt
Remove the use of CONFIG_MV643XX_ETH_[012] variables on most platforms.
Instead, platform-specific code enables the ports supported by the
hardware. After this patch, these config variables are only used in
arch/ppc, so also move them from drivers/net/Kconfig to arch/ppc/Kconfig.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: Jeff Garzik <jeff@garzik.org> Cc: Paul Mackerras <paulus@samba.org>
Mark Brown [Mon, 19 Feb 2007 20:15:40 +0000 (20:15 +0000)]
natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY. This patch adds a new device table entry supporting these cards.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Brown [Mon, 19 Feb 2007 20:15:39 +0000 (20:15 +0000)]
natsemi: Add support for using MII port with no PHY
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool. Any PHYs that are present can be accessed via the MII
ioctl()s.
This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a workqueue function that needs RTNL is running when skge_down
is called then a deadlock is possible. Fix by only clearing the timer,
and handling the flush_scheduled_work on removal. This work queue is only
ever used for the old fiber based boards.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Russell King [Tue, 20 Feb 2007 15:44:23 +0000 (15:44 +0000)]
[ARM] Fix ARM AACI ALSA driver
CC [M] sound/arm/aaci.o
sound/arm/aaci.c:729: error: parse error before '*' token
sound/arm/aaci.c:731: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:786: error: parse error before '*' token
sound/arm/aaci.c:786: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:827: error: parse error before '*' token
sound/arm/aaci.c:828: warning: function declaration isn't a prototype
...
sound/arm/aaci.c:845: error: parse error before "aaci_capture_ops"
sound/arm/aaci.c:845: warning: type defaults to `int' in declaration of `aaci_capture_ops'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Brownell [Tue, 20 Feb 2007 05:28:53 +0000 (21:28 -0800)]
[ARM] fix mach-at91 build breakage
The rename of the AT91 subtree from mach-at91rm9200 to mach-at91
(to accomodate at91sam926x processors) was incomplete. It needs
this patch to be able to build again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 20 Feb 2007 15:23:57 +0000 (15:23 +0000)]
[ARM] Fix jornada720 build errors
kernel/built-in.o: In function `pm_suspend':
utsname_sysctl.c:(.text+0x23008): multiple definition of `pm_suspend'
arch/arm/mach-sa1100/built-in.o:arch/arm/mach-sa1100/sleep.S:(.text+0xf68): first defined here
arm-linux-ld: Warning: size of symbol `pm_suspend' changed from 20 in arch/arm/mach-sa1100/built-in.o to 44 in kernel/built-in.o
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6-omap-h63xx.git / log