Felipe Balbi [Sun, 15 Feb 2009 01:30:09 +0000 (01:30 +0000)]
arm: omap1: get rid of OMAP_TAG_USB
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
This patch is compile tested only.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 27 Feb 2009 22:46:08 +0000 (22:46 +0000)]
omap3: gpio pin config bugfixes
Bugfix several GPIO mux configurations which didn't enable the
input drivers, but weren't named as e.g. ..._GPIO141_OUT.
These bugs were added quite recently, for OMAP3 EVM support.
To help avoid such bugs in the future, update the comment to
clarify the rule: always use PIN_INPUT, unless the name uses
that name suffix, to be crystal-clear on the signal's use as
output-only.
(Also adds GPIO-63, for the EVM's MMC-1 writeprotect switch.
Presumably that works right...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the spurious interrupt issue on a DMA channel.
In OMAP sDMA, contrast to the SDMA.DMA4_CSRi registers, the
SDMA.DMA4_IRQSTATUS_Lj registers are updated regardless of
the corresponding bits in the SDMA.DMA4_IRQENABLE_Lj registers.
Since there are four sDMA interrupt lines and if more than one
line is actively used by two concurrently running sDMA softwares
modules,then the spurious interrupt can be observed on the other
lines.
Fix in this patch will only dispatch the relevant and enabled
interrupts on a particular line thus perevting spurious IRQ.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked By: Nishant Kamat <nskamat@ti.com>
cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch set up a cmdline option for omap dma for masking the
available channels. It is needed since the OMAP DMA is a system wide
resource and can be used by another software apart from the kernel.
To reserve the omap SDMA channels for kernel dma usage, use cmdline
bootarg "omap_dma_reserve_ch=". The valid range is 1 to 32.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked By: Nishant Kamat <nskamat@ti.com>
cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Thu, 19 Feb 2009 13:29:57 +0000 (13:29 +0000)]
twl4030: move twl4030-pwrbutton to drivers/input/misc
Take it out of drivers/i2c/chips as requested by Jean Delvare
that all drivers move out of there.
Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Thu, 19 Feb 2009 13:29:56 +0000 (13:29 +0000)]
i2c: move twl4030-pwrbutton to child registration style
This patch is *compile tested only*. It moves twl4030-pwrbutton
to a platform_driver so it can be registered as a child of
twl4030-core.c.
Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Samuel Ortiz <sameo@openedhand.com> Signed-off-by: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen [Fri, 20 Feb 2009 14:13:55 +0000 (14:13 +0000)]
twl4030-madc: Let the operation complete faster
No need to wait before the first read, as the operation is likely
completed already. For timeout 50 milliseconds is an overkill, poll the
register for the duration of 5 milliseconds at maximum.
Also, clear the active flag in case of timeout.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Aaro Koskinen [Fri, 20 Feb 2009 14:13:54 +0000 (14:13 +0000)]
twl4030-madc: Convert ioctl to unlocked
Use unlocked ioctl instead of taking the BKL for an operation that can
take some milliseconds. The driver mutex is now taken before the active
status check, so that the concurrent users of this ioctl won't start
seeing EBUSY (previously guaranteed by the BKL).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3: SDTI: Prevent access to sdti writing if module is not initialized.
The function sti_channel_write_trace can be run from process and interrupt
context. It has to be completed before other sti_channel_write_trace calls.
Prevent sdti writing when SDTI module is not initialized.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Fri, 20 Feb 2009 22:30:37 +0000 (22:30 +0000)]
input: lm8323: apply comments from mainline
On Sat, Feb 21, 2009 at 12:21:34AM +0200, Felipe Balbi wrote:
> In order to avoid conflicts later, let's sync omap
> version with the version accepted by mainline after
> fixing a few comments.
>
> Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Wait a minute, I forgot one hunk, here's an updated version:
========== cut here ==========
>From 370931163e963de1b3cd38d25c1233adebabd103 Mon Sep 17 00:00:00 2001
From: Felipe Balbi <me@felipebalbi.com>
Date: Thu, 19 Feb 2009 19:53:59 +0200
Subject: [PATCH] input: lm8323: apply comments from mainline
In order to avoid conflicts later, let's sync omap
version with the version accepted by mainline after
fixing a few comments.
Signed-off-by: Felipe Balbi <me@felipebalbi.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Mon, 23 Feb 2009 00:26:09 +0000 (16:26 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Add missing mutex_lock(&dev->struct_mutex)
drm/i915: fix WC mapping in non-GEM i915 code.
drm/i915: Fix regression in 95ca9d
drm/i915: Retire requests from i915_gem_busy_ioctl.
drm/i915: suspend/resume GEM when KMS is active
drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.
Eric Anholt [Wed, 18 Feb 2009 17:44:56 +0000 (09:44 -0800)]
drm/i915: Retire requests from i915_gem_busy_ioctl.
This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jesse Barnes [Tue, 17 Feb 2009 23:13:31 +0000 (15:13 -0800)]
drm/i915: suspend/resume GEM when KMS is active
In the KMS case, we need to suspend/resume GEM as well. So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@redhat.com>
Eric Anholt [Thu, 19 Feb 2009 22:54:51 +0000 (14:54 -0800)]
drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted. Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.
Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Dave Airlie <airlied@redhat.com>
Paul Moore [Fri, 20 Feb 2009 21:33:02 +0000 (16:33 -0500)]
selinux: Fix the NetLabel glue code for setsockopt()
At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question. The problem was noticed by someone trying to use the
"-R" (record route) option of ping:
# ping -R 10.0.0.1
ping: record route: No message of desired type
The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed. Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Paul Moore [Fri, 20 Feb 2009 21:32:55 +0000 (16:32 -0500)]
cipso: Fix documentation comment
The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory. This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online. For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.
Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: James Morris <jmorris@namei.org>
Linus Torvalds [Sun, 22 Feb 2009 21:26:30 +0000 (13:26 -0800)]
Merge branch 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix
Randy Dunlap [Sun, 22 Feb 2009 20:15:45 +0000 (12:15 -0800)]
docbook: split kernel-api for device-drivers
The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems. This allows these docbooks
to be generated in parallel. (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)
The chapters that were moved from kernel-api to device-drivers are:
Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PM: Split up sysdev_[suspend|resume] from device_power_[down|up]
Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.
This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 22 Feb 2009 18:27:49 +0000 (10:27 -0800)]
x86: Add IRQF_TIMER to legacy x86 timer interrupt descriptors
Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.
The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.
Cc: Rafael J. Wysocki <rjw@sisk.pl> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 22 Feb 2009 17:28:46 +0000 (09:28 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: remove CONFIG_ACPI_SYSTEM
fujitsu-laptop: Use RFKILL support bitmask from firmware
x86_64: Fix S3 fail path
x86_64: acpi/wakeup_64 cleanup
battery: don't assume we are fully charged when not charging or discharging
ACPI: EC: Add delay for slow MSI controller
Bjorn Helgaas [Thu, 19 Feb 2009 19:56:16 +0000 (12:56 -0700)]
ACPI: remove CONFIG_ACPI_SYSTEM
Remove CONFIG_ACPI_SYSTEM. It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".
Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Len Brown <len.brown@intel.com>
Tony Vroon [Mon, 2 Feb 2009 11:11:10 +0000 (11:11 +0000)]
fujitsu-laptop: Use RFKILL support bitmask from firmware
Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.
This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.
Signed-off-by: Tony Vroon <tony@linx.net> Tested-by: Stephen Gildea <stepheng+linux@gildea.com> Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au> Signed-off-by: Len Brown <len.brown@intel.com>
Jiri Slaby [Sun, 15 Feb 2009 21:46:45 +0000 (22:46 +0100)]
x86_64: Fix S3 fail path
As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.
Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com>
Jiri Slaby [Sun, 15 Feb 2009 21:45:49 +0000 (22:45 +0100)]
x86_64: acpi/wakeup_64 cleanup
- remove %ds re-set, it's already set in wakeup_long64
- remove double labels and alignment (ENTRY already adds both)
- use meaningful resume point labelname
- skip alignment while jumping from wakeup_long64 to the resume point
- remove .size, .type and unused labels
[v2]
- added ENDPROCs
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Cyrill Gorcunov <gorcunov@openvz.org> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 21 Feb 2009 22:17:26 +0000 (14:17 -0800)]
Merge branch 'hibernate'
* hibernate:
PM: Fix suspend_console and resume_console to use only one semaphore
PM: Wait for console in resume
PM: Fix pm_notifiers during user mode hibernation
swsusp: clean up shrink_all_zones()
swsusp: dont fiddle with swappiness
PM: fix build for CONFIG_PM unset
PM/hibernate: fix "swap breaks after hibernation failures"
PM/resume: wait for device probing to finish
Consolidate driver_probe_done() loops into one place
Arve Hjønnevåg [Sat, 14 Feb 2009 01:07:24 +0000 (02:07 +0100)]
PM: Fix suspend_console and resume_console to use only one semaphore
This fixes a race where a thread acquires the console while the
console is suspended, and the console is resumed before this
thread releases it. In this case, the secondary console
semaphore would be left locked, and the primary semaphore would
be released twice. This in turn would cause the console switch
on suspend or resume to hang forever.
Note that suspend_console does not actually lock the console
for clients that use acquire_console_sem, it only locks it for
clients that use try_acquire_console_sem. If we change
suspend_console to fully lock the console, then the kernel
may deadlock on suspend. One client of try_acquire_console_sem
is acquire_console_semaphore_for_printk, which uses it to
prevent printk from using the console while it is suspended.
Signed-off-by: Arve Hjønnevåg <arve@android.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arve Hjønnevåg [Sat, 14 Feb 2009 01:06:17 +0000 (02:06 +0100)]
PM: Wait for console in resume
Avoids later waking up to a blinking cursor if the device woke up and
returned to sleep before the console switch happened.
Signed-off-by: Brian Swetland <swetland@google.com> Signed-off-by: Arve Hjønnevåg <arve@android.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Borzenkov [Sat, 14 Feb 2009 01:05:14 +0000 (02:05 +0100)]
PM: Fix pm_notifiers during user mode hibernation
Snapshot device is opened with O_RDONLY during suspend and O_WRONLY durig
resume. Make sure we also call notifiers with correct parameter telling
them what we are really doing.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Sat, 14 Feb 2009 01:04:10 +0000 (02:04 +0100)]
swsusp: clean up shrink_all_zones()
Move local variables to innermost possible scopes and use local
variables to cache calculations/reads done more than once.
No change in functionality (intended).
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Sat, 14 Feb 2009 01:03:08 +0000 (02:03 +0100)]
swsusp: dont fiddle with swappiness
sc.swappiness is not used in the swsusp memory shrinking path, do not
set it.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Jenkins [Sat, 14 Feb 2009 01:01:14 +0000 (02:01 +0100)]
PM/hibernate: fix "swap breaks after hibernation failures"
http://bugzilla.kernel.org/show_bug.cgi?id=12239
The image writing code dropped a reference to the current swap device.
This doesn't show up if the hibernation succeeds - because it doesn't
affect the image which gets resumed. But it means multiple _failed_
hibernations end up freeing the swap device while it is still use!
swsusp_write() finds the block device for the swap file using swap_type_of().
It then uses blkdev_get() / blkdev_put() to open and close the block device.
Unfortunately, blkdev_get() assumes ownership of the inode of the block_device
passed to it. So blkdev_put() calls iput() on the inode. This is by design
and other callers expect this behaviour. The fix is for swap_type_of() to take
a reference on the inode using bdget().
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Cc: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 14 Feb 2009 01:00:19 +0000 (02:00 +0100)]
PM/resume: wait for device probing to finish
the resume code does not currently wait for device probing to finish.
Even without async function calls this is dicey and not correct,
but with async function calls during the boot sequence this is going
to get hit more...
This patch adds the synchronization using the newly introduced helper.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Acked-by: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 14 Feb 2009 00:59:06 +0000 (01:59 +0100)]
Consolidate driver_probe_done() loops into one place
there's a few places that currently loop over driver_probe_done(), and
I'm about to add another one. This patch abstracts it into a helper
to reduce duplication.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Len Brown <lenb@kernel.org> Acked-by: Greg KH <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Hughes [Sun, 25 Jan 2009 15:05:50 +0000 (15:05 +0000)]
battery: don't assume we are fully charged when not charging or discharging
On hardware like the T61 it can take a couple of seconds for the battery
to start charging after the power is connected, and we incorrectly tell
userspace that we are fully charged, and then go back to charging.
Only mark a battery as fully charged when the preset charge matches either
the last full charge, or the design charge.
http://bugzilla.kernel.org/show_bug.cgi?id=12632
Signed-off-by: Richard Hughes <hughsient@gmail.com> Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts
[CIFS] improve posix semantics of file create
[CIFS] Fix oops in cifs_strfromUCS_le mounting to servers which do not specify their OS
cifs: posix fill in inode needed by posix open
cifs: properly handle case where CIFSGetSrvInodeNumber fails
cifs: refactor new_inode() calls and inode initialization
[CIFS] Prevent OOPs when mounting with remote prefixpath.
[CIFS] ipv6_addr_equal for address comparison
introduced a call to mce_cpu_features() in the resume path, in order
for the MCE machinery to get properly reinitialized after a resume.
However, this function (and its successors) was flagged __cpuinit,
which becomes __init on UP configurations (on SMP suspend/resume
requires CPU hotplug and so this would not be seen.)
Remove the offending __cpuinit annotations for mce_cpu_features() and
its successor functions.
Cc: Andi Kleen <ak@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Steve French [Fri, 20 Feb 2009 05:43:09 +0000 (05:43 +0000)]
[CIFS] Fix multiuser mounts so server does not invalidate earlier security contexts
When two different users mount the same Windows 2003 Server share using CIFS,
the first session mounted can be invalidated. Some servers invalidate the first
smb session when a second similar user (e.g. two users who get mapped by server to "guest")
authenticates an smb session from the same client.
By making sure that we set the 2nd and subsequent vc numbers to nonzero values,
this ensures that we will not have this problem.
Fixes Samba bug 6004, problem description follows:
How to reproduce:
- configure an "open share" (full permissions to Guest user) on Windows 2003
Server (I couldn't reproduce the problem with Samba server or Windows older
than 2003)
- mount the share twice with different users who will be authenticated as guest.
Steve French [Fri, 20 Feb 2009 04:32:45 +0000 (04:32 +0000)]
[CIFS] improve posix semantics of file create
Samba server added support for a new posix open/create/mkdir operation
a year or so ago, and we added support to cifs for mkdir to use it,
but had not added the corresponding code to file create.
The following patch helps improve the performance of the cifs create
path (to Samba and servers which support the cifs posix protocol
extensions). Using Connectathon basic test1, with 2000 files, the
performance improved about 15%, and also helped reduce network traffic
(17% fewer SMBs sent over the wire) due to saving a network round trip
for the SetPathInfo on every file create.
It should also help the semantics (and probably the performance) of
write (e.g. when posix byte range locks are on the file) on file
handles opened with posix create, and adds support for a few flags
which would have to be ignored otherwise.
Certain NAS appliances do not set the operating system or network operating system
fields in the session setup response on the wire. cifs was oopsing on the unexpected
zero length response fields (when trying to null terminate a zero length field).
This fixes the oops.
Acked-by: Jeff Layton <jlayton@redhat.com> CC: stable <stable@kernel.org> Signed-off-by: Steve French <sfrench@us.ibm.com>
Igor Mammedov [Tue, 10 Feb 2009 11:10:26 +0000 (14:10 +0300)]
[CIFS] Prevent OOPs when mounting with remote prefixpath.
Fixes OOPs with message 'kernel BUG at fs/cifs/cifs_dfs_ref.c:274!'.
Checks if the prefixpath in an accesible while we are still in cifs_mount
and fails with reporting a error if we can't access the prefixpath
Should fix Samba bugs 6086 and 5861 and kernel bug 12192
Signed-off-by: Igor Mammedov <niallain@gmail.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Sat, 21 Feb 2009 02:04:53 +0000 (18:04 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (26 commits)
drm/radeon: update sarea copies of last_ variables on resume.
drm/i915: Keep refs on the object over the lifetime of vmas for GTT mmap.
drm/i915: take struct mutex around fb unref
drm: Use spread spectrum when the bios tells us it's ok.
drm: Collapse identical i8xx_clock() and i9xx_clock().
drm: Bring PLL limits in sync with DDX values.
drm: Add locking around cursor gem operations.
drm: Propagate failure from setting crtc base.
drm: Check for a NULL encoder when reverting on error path
drm/i915: Cleanup the hws on ringbuffer constrution failure.
drm/i915: Don't add panel_fixed_mode to the probed modes list at LVDS init.
drm: Release user fbs in drm_release
drm/i915: Unpin the fb on error during construction.
drm/i915: Unpin the hws if we fail to kmap.
drm/i915: Unpin the ringbuffer if we fail to ioremap it.
drm/i915: unpin for an invalid memory domain.
drm/i915: Release and unlock on mmap_gtt error path.
drm/i915: Set framebuffer alignment based upon the fence constraints.
drm: Do not leak a new reference for flink() on an existing name
drm/i915: Fix potential AB-BA deadlock in i915_gem_execbuffer()
...
Linus Torvalds [Sat, 21 Feb 2009 02:03:07 +0000 (18:03 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: use the right protections for split-up pagetables
x86, vmi: TSC going backwards check in vmi clocksource
8250: fix boot hang with serial console when using with Serial Over Lan port
Intel 8257x Ethernet boards have a feature called Serial Over Lan.
This feature works by emulating a serial port, and it is detected by
kernel as a normal 8250 port. However, this emulation is not perfect, as
also noticed on changeset 7500b1f602aad75901774a67a687ee985d85893f.
Before this patch, the kernel were trying to check if the serial TX is
capable of work using IRQ's.
This works fine for other 8250 ports, but, on 8250-emulated SoL port, the
chip is a little lazy to down UART_IIR_NO_INT at UART_IIR register.
Due to that, UART_BUG_TXEN is sometimes enabled. However, as TX IRQ keeps
working, and the TX polling is now enabled, the driver miss-interprets the
IRQ received later, hanging up the machine until a key is pressed at the
serial console.
This is the 6 version of this patch. Previous versions were trying to
introduce a large enough delay between serial_outp and serial_in(up,
UART_IIR), but not taking forever. However, the needed delay couldn't be
safely determined.
At the experimental tests, a delay of 1us solves most of the cases, but
still hangs sometimes. Increasing the delay to 5us was better, but still
doesn't solve. A very high delay of 50 ms seemed to work every time.
However, poking around with delays and pray for it to be enough doesn't
seem to be a good approach, even for a quirk.
So, instead of playing with random large arbitrary delays, let's just
disable UART_BUG_TXEN for all SoL ports.
Tejun Heo [Fri, 20 Feb 2009 23:38:48 +0000 (15:38 -0800)]
vmalloc: call flush_cache_vunmap() from unmap_kernel_range()
Impact: proper vcache flush on unmap_kernel_range()
flush_cache_vunmap() should be called before pages are unmapped. Add
a call to it in unmap_kernel_range().
Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Nick Piggin <npiggin@suse.de> Acked-by: David S. Miller <davem@davemloft.net> Cc: <stable@kernel.org> [2.6.28.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Fri, 20 Feb 2009 23:38:48 +0000 (15:38 -0800)]
cpuset: various documentation fixes and updates
I noticed the old commit 8f5aa26c75b7722e80c0c5c5bb833d41865d7019
("cpusets: update_cpumask documentation fix") is not a complete fix,
resulting in inconsistent paragraphs. This patch fixes it and does other
fixes and updates:
- s/migrate_all_tasks()/migrate_live_tasks()/
- describe more cpuset control files
- s/cpumask_t/struct cpumask/
- document cpu hotplug and change of 'sched_relax_domain_level' may cause
domain rebuild
- document various ways to query and modify cpusets
- the equivalent of "mount -t cpuset" is "mount -t cgroup -o cpuset,noprefix"
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilpo Järvinen [Fri, 20 Feb 2009 23:38:45 +0000 (15:38 -0800)]
sx.c: fix dbl statement if - add missing braces
Caused by 736d54533aed (sx.c: fix missed unlock_kernel() on error path in
sx_fw_ioctl()). You guys keep breaking things this way in every single
kernel release in at least couple of places... :-(
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Acked-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 20 Feb 2009 23:38:41 +0000 (15:38 -0800)]
slab: introduce kzfree()
kzfree() is a wrapper for kfree() that additionally zeroes the underlying
memory before releasing it to the slab allocator.
Currently there is code which memset()s the memory region of an object
before releasing it back to the slab allocator to make sure
security-sensitive data are really zeroed out after use.
These callsites can then just use kzfree() which saves some code, makes
users greppable and allows for a stupid destructor that isn't necessarily
aware of the actual object size.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Matt Mackall <mpm@selenic.com> Acked-by: Christoph Lameter <cl@linux-foundation.org> Cc: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Lindgren [Fri, 20 Feb 2009 21:16:53 +0000 (13:16 -0800)]
Build fixes for McBSP wakeups
Commit 050893ae211017753ffb90d19aafc86da967ac28 was missing
the related register defines. Add the register defines to
fix build and also clean-up a bit to get rid of build warnings
omap1.
Steve Sakoman [Mon, 2 Feb 2009 06:27:49 +0000 (06:27 +0000)]
ARM: Add SMSC911X support to Overo platform (V2)
Gumstix will soon be shipping a variant of their Summit board that
includes an SMSC LAN9221 ethernet interface. This patch provides
support via the smsc911x driver when enabled in kernel config.
The Overo defconfig is not updated since the LAN9221 is an option
not present on all systems.
Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Fri, 6 Feb 2009 03:45:25 +0000 (03:45 +0000)]
OMAP3: update ES level flags to discriminate between post-ES2 revisions
Some OMAP3 chip behaviors change in ES levels after ES2. Modify the
existing omap_chip flags to add options for ES3.0 and ES3.1.
Add a new macro, CHIP_GE_OMAP3430ES2, to cover ES levels from ES2
onwards - a common pattern for OMAP3 features. Update all current
users of the omap_chip macros to use this new macro.
Also add CHIP_GE_OMAP3430ES3_1 to cover the USBTLL SAR errata case
(described and fixed in the following patch)
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Device connected to MMC3 is assumed to be self-powered, so
set_power() function is empty. It can't be omited because
host driver requires it. Array size for hsmmc[] is specified
because hsmmc[2].name is needed for MMC3 name.
Also fix a leak which happens if invalid controller id
is passed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Mon, 9 Feb 2009 07:59:57 +0000 (07:59 +0000)]
ARM: OMAP: Add method to register additional I2C busses on the command line
This patch extends command line option "i2c_bus=bus_id,clkrate" so that
it allow to register additional I2C busses that are not registered with
omap_register_i2c_bus from board initialization code.
Purpose of this is to register additional board busses which are routed
to external connectors only without any on board I2C devices.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Nikula [Mon, 9 Feb 2009 07:59:56 +0000 (07:59 +0000)]
ARM: OMAP: Add command line option for I2C bus speed
This patch adds a new command line option "i2c_bus=bus_id,clkrate" into
I2C bus registration helper. Purpose of the option is to override the
default board specific bus speed which is supplied by the
omap_register_i2c_bus.
The default bus speed is typically set to speed of slowest I2C chip on the
bus and overriding allow to use some experimental configurations or updated
chip versions without any kernel modifications.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
usb: musb: adding support for registering nop xceiv
Adding support for registering nop usb transceiver for musb
platforms. Tested with OMAP35xx EVM having OTG phy ISP1504
which is autonomous and doesn't require any phy programming.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Koen Kooi [Sun, 25 Jan 2009 08:46:17 +0000 (09:46 +0100)]
board-omap3beagle: set i2c-3 to 100kHz
Changing it do 100kHz is needed to make more devices works properly. Controlling the TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine. EDID readout is unaffected by this change.
Ingo Molnar [Fri, 20 Feb 2009 07:04:13 +0000 (08:04 +0100)]
x86: use the right protections for split-up pagetables
Steven Rostedt found a bug in where in his modified kernel
ftrace was unable to modify the kernel text, due to the PMD
itself having been marked read-only as well in
split_large_page().
The fix, suggested by Linus, is to not try to 'clone' the
reference protection of a huge-page, but to use the standard
(and permissive) page protection bits of KERNPG_TABLE.
The 'cloning' makes sense for the ptes but it's a confused and
incorrect concept at the page table level - because the
pagetable entry is a set of all ptes and hence cannot
'clone' any single protection attribute - the ptes can be any
mixture of protections.
With the permissive KERNPG_TABLE, even if the pte protections
get changed after this point (due to ftrace doing code-patching
or other similar activities like kprobes), the resulting combined
protections will still be correct and the pte's restrictive
(or permissive) protections will control it.
Also update the comment.
This bug was there for a long time but has not caused visible
problems before as it needs a rather large read-only area to
trigger. Steve possibly hacked his kernel with some really
large arrays or so. Anyway, the bug is definitely worth fixing.
[ Huang Ying also experienced problems in this area when writing
the EFI code, but the real bug in split_large_page() was not
realized back then. ]
projects / linux-2.6-omap-h63xx.git / log