Jan Engelhardt [Thu, 19 Apr 2007 21:21:41 +0000 (16:21 -0500)]
Use menuconfig objects: MTD
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Shashi Rao [Wed, 28 Mar 2007 22:56:28 +0000 (15:56 -0700)]
[MTD] Fix fwh_lock locking
This is on a custom board with a mapping driver access to an ST
M50LPW080 chip. This chip is probed successfully with
do_map_probe("jedec_probe",...). If I use the mtdchar interface to
perform unlock->erase->program->lock on any of the 16 eraseblocks in the
chip, the chip is left in FL_STATUS mode while the data structures
believe that the chip is in FL_READY mode. Hence, any subsequent reads
to any flash byte results in 0x80 being read.
Signed-off-by: Shashi Rao <shashi@sun.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Joakim Tjernlund [Tue, 27 Mar 2007 11:32:09 +0000 (13:32 +0200)]
[JFFS2] Speed up mount for directly-mapped NOR flash
Remove excessive scanning of empty flash after a clean
marker for users of the point/unpoint method. cfi_cmdset_0001
uses point/unpoint by default iff flash mapping is linear.
The speedup is several orders of magnitude if FS is less than
half full.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
[JFFS2] fix buffer sise calculations in jffs2_get_inode_nodes()
In read inode we have an optimization which prevents one
min. I/O unit (e.g. NAND page) to be read more then once.
Namely, at the beginning we do not know which node type we read,
so we read so we assume we read the directory entry, because it
has the smallest node header. When we read it, we read up to the
next min. I/O unit, just because if later we'll need to read more,
we already have this data.
If it turns out to be that the node is not directory entry, and
we need more data, and we did not read it because it sits in the
next min. I/O unit, we read the whole next (or several next)
min. I/O unit(s). And if it happens to be that we read a data node,
and we've read part of its data, we calculate partial CRC.
So if later we need to check data CRC, we'll only read the rest
of the data from further min. I/O units and continue CRC checking.
This code was a bit messy and buggy. The bug was that it assumed
relatively large min. I/O unit, so that the largest node header
could overlap only one min. I/O unit boundary.
This parch clean-ups the code a bit and fixes this bug.
The patch was not tested on flash with small min. I/O unit, like
NOR-ECC, nut it was tested on NAND with 512 bytes NAND page, so
it at least does not break NAND. It was also tested with mtdram
so it should not break NOR.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Wed, 4 Apr 2007 10:47:53 +0000 (13:47 +0300)]
[JFFS2] Disable summary after wbuf recovery
After a write error, any data in the write buffer must
be relocated. This is handled by the jffs2_wbuf_recover
function. This function does not fix up the erase block
summary information that is collected for writing at the
end of the block, which results in an incorrect summary
(or BUG if the summary was found to be empty).
As the summary is not essential (it is an optimisation),
it may be disabled for the current erase block when this
situation arises. This patch does that.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Thu, 29 Mar 2007 08:00:47 +0000 (11:00 +0300)]
[JFFS2] Prevent list corruption when handling write errors
If a write error occurs, the affected block is placed on the
bad_used_list. In the case that the write error occured
when writing summary data the block was also being placed on
the dirty_list, which caused list corruption and ultimately
a soft lockup in jffs2_mark_node_obsolete. This fixes that.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Mon, 19 Mar 2007 10:49:11 +0000 (12:49 +0200)]
[MTD] nandsim: enhance nandsim to allow arbitrary NAND size
A new module parameter has been added called 'overridesize',
which overrides the size that would be determined by the
ID bytes. 'overridesize' is specified in erase blocks and
as the exponent of a power of two e.g. 5 means a size of
32 erase blocks.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adrian Hunter [Mon, 19 Mar 2007 10:47:45 +0000 (12:47 +0200)]
[MTD] nandsim: enhance nandsim to simulate flash errors
New module parameters have been added to nandsim to
simulate:
bitflips random bit flips
badblocks blocks that are initially marked bad
weakblocks blocks that fail to erase after a
small number of erase cycles
weakpages pages that fail to write after a
small number of successful writes
gravepages pages that fail to read after a
small number of successful reads
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Artem Bityutskiy [Wed, 21 Mar 2007 09:07:05 +0000 (11:07 +0200)]
[JFFS2] fix deadlock on error path
When the MTD driver returns write failure, the following deadlock
occurs:
We are in __jffs2_flush_wbuf(), we hold &c->wbuf_sem. Write failure.
jffs2_wbuf_recover()->jffs2_reserve_space_gc()->jffs2_do_reserve_space()
->jffs2_erase_pending_blocks()->jffs2_flash_read()
and it tries to lock &c->wbuf_sem again. Deadlock.
Reported-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Andre Renaud [Tue, 17 Apr 2007 17:50:59 +0000 (13:50 -0400)]
[MTD] [NAND] Casting bug in nand_default_block_markbad
There is a slight bug in nand_default_block_markbad, where the offset is
cast to an integer, prior to being shifted. This means that on large
offsets, it is incorrectly doing a signed shift & losing bits. Fixed
this by doing the cast after the shift (as is done elsewhere in the code).
Signed-off-by: Andre Renaud <andre@bluewatersys.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for AT26Fxxx dataflash devices. These devices have a quite different
commandset than the AT45xxx chips, which are handled by at91_dataflash.c, so a
combined driver turned out to be more ugly than useful.
Tested only on AT26F004.
Signed-off-by: Hans-Jürgen Koch <hjk@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Thomas Gleixner [Tue, 17 Apr 2007 17:30:57 +0000 (18:30 +0100)]
[MTD] [NAND] Move ancient NAND chip support into a config option
The support for obsolete ancient NAND chips adds .data size and one
of the old ids conflicts with a modern one. Make the support for
such chips depending on a config option.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Ralf Baechle [Sat, 10 Mar 2007 23:10:50 +0000 (23:10 +0000)]
[MTD] Fix dependencies for MIPS MTD drivers
o A dependency on the processor architecture does not make sense;
delete it.
o The Alchemy and MTX drivers requires MTD_PARTITIONS and MTD_CFI to work,
make those dependencies.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Robert P. J. Day [Tue, 27 Mar 2007 05:45:41 +0000 (21:45 -0800)]
[JFFS2] Delete everything related to obsolete JFFS2_PROC option
Delete everything related to the apparently non-existent kernel config
option JFFS2_PROC.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Marc St-Jean [Tue, 27 Mar 2007 05:45:41 +0000 (21:45 -0800)]
[MTD] PMC MSP71xx flash/rootfs mappings
Add flash and rootfs mappings for the PMC-Sierra MSP71xx devices.
This patch references some platform support files previously submitted to
the linux-mips@linux-mips.org list.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (23 commits)
USB Elan FTDI: check for workqueue creation
USB: fix spinlock recursion in cdc-acm.c
USB: fix Unaligned access in EHCI driver
USB: Product ID for FT232RL in ftdi_sio
USBNET: DM9501: Add Corega FEther USB-TXC support.
USB: ipaq.c: Additional devices
USB: further fix for usb-serial
USB: fix usb-serial device naming bug
USB: RTS/DTR signal patch for airprime driver
USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
usb-serial: fix shutdown / device_unregister order
USB: add Additional PIDs in ftdi_sio
USB: add QL355P power supply ids to fdti_sio
USB: New device IDs for cp2101 driver
USB: kill dead code from hub.c
USB: ratelimit debounce error messages
USB: pxa2xx_udc: fix hardcoded irq number
UHCI: fix port resume problem
USB: set the correct interval for interrupt URBs
USB: goku_udc: Remove crude cache coherency code
...
Delay the read of the EC status register until
after the event that caused it occurs -- otherwise
it is possible to read and act on stale status that was
associated with the previous event.
Do this with a perpetually incrementing "event_count" to detect
when a new event occurs and it is safe to read status.
There is no workaround for polling mode -- it is inherently
exposed to reading and acting on stale status, since it
doesn't have an interrupt to tell it the event completed.
http://bugzilla.kernel.org/show_bug.cgi?id=8110
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Gard Spreemann [Sun, 4 Mar 2007 23:03:26 +0000 (00:03 +0100)]
USB: Product ID for FT232RL in ftdi_sio
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
Oliver Neukum [Mon, 26 Feb 2007 14:43:00 +0000 (15:43 +0100)]
USB: fix usb-serial device naming bug
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1f96c2d8c0f3d28b7d407743806256c is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
Martin Schiller [Thu, 1 Mar 2007 12:49:48 +0000 (13:49 +0100)]
USB: RTS/DTR signal patch for airprime driver
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Jim Radford [Wed, 28 Feb 2007 18:10:50 +0000 (10:10 -0800)]
USB: ftdi_sio: use port_probe / port_remove thereby fixing access to the latency_timer
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jim Radford [Wed, 28 Feb 2007 16:14:13 +0000 (08:14 -0800)]
usb-serial: fix shutdown / device_unregister order
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
Alan Stern [Mon, 26 Feb 2007 22:16:06 +0000 (17:16 -0500)]
UHCI: fix port resume problem
This patch (as863) fixes a problem encountered sometimes when resuming
a port on a UHCI controller. The hardware may turn off the
Resume-Detect bit before turning off the Suspend bit, leading usbcore
to think that the port is still suspended and the resume has failed.
The patch makes uhci_finish_suspend() wait until both bits are safely
off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 26 Feb 2007 19:56:14 +0000 (14:56 -0500)]
USB: set the correct interval for interrupt URBs
This patch (as862) fixes a couple of bugs in the way usbcore handles
intervals for interrupt URBs. usb_interrupt_msg (and usb_bulk_msg for
backward compatibility) don't set the interval correctly for
high-speed devices. proc_do_submiturb() doesn't set it correctly when
a bulk URB is submitted to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IMHO, ACPI disabled due to DMI failure or blacklisted year should be noted,
as is done with other ACPI blacklisting.
This will help people troubleshoot when ACPI isn't working. Status quo is
a mysterious "ACPI Disabled" message without explanation on BIOS that
implements ACPI but not DMI. This is actually fairly common on embedded
x86 boards.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Len Brown <len.brown@intel.com>
Sam Ravnborg [Tue, 27 Feb 2007 09:22:00 +0000 (10:22 +0100)]
PCI: aer: fix section mismatch warning
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:aer_probe from .data between 'aerdrv' (at offset 0x1608) and 'aer_error_handlers'
Warning was fixed by renaming aerdrv to aerdriver so we pass the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sam Ravnborg [Tue, 27 Feb 2007 09:19:17 +0000 (10:19 +0100)]
pcie: fix section mismatch warning
Fix following section mismatch warning (when compiled with CONFIG_HOTPLUG=n):
WARNING: drivers/pci/built-in.o - Section mismatch: reference to .init.text:pcie_portdrv_probe from .data between 'pcie_portdrv' (at offset 0xe40) and 'pcie_portdrv_err_handler'
This warning was fixed by renaming pcie_portdrv to pcie_portdriver so we pass
the whitelist.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tejun Heo [Sun, 25 Feb 2007 12:36:01 +0000 (04:36 -0800)]
PCI: allow multiple calls to pcim_pin_device()
Sanity check in pcim_pin_device() was too restrictive in that it didn't
allow multiple calls to the function, which is against the devres
philosohpy of fire-and-forget. Track pinned status separately and allow
pinning multiple times.
Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johannes Berg [Wed, 28 Feb 2007 11:38:31 +0000 (12:38 +0100)]
driver core: export device_rename
In wireless we'd like to allow renaming of the phy devices we surface in
sysfs. The base wireless code, however, can be built modular and thus we
need device_rename exported.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the device symlink back to sysfs even if
CONFIG_SYSFS_DEPRECATED is enabled as too many userspace programs (well,
HAL), still rely on this link to be present.
I will rework the ability for sysfs to change layouts like this in the
future, but for now, this patch should fix people's network connections.
Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Matt Mackall <mpm@selenic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It was the incorrect fix and causes a reference counting bug whenever
any driver module is removed from the system. Mike Galbraith
<efault@gmx.de> is looking for the real fix for his problem.
Kristen Accardi [Fri, 9 Mar 2007 23:15:33 +0000 (18:15 -0500)]
libata-acpi: allow _GTF on SATA, but disable on PATA for now
The ACPI specification states, and BIOS implementations depend on,
_STM being called before _GTF.
SATA does this, but PATA does not. So for now, simply
prevent execution of _GTF on PATA devices. Longer term we
should implement ACPI support for PATA devices in libata.
Signed-off-by: Kristen Accardi <kristen.c.accardi@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Fri, 9 Mar 2007 22:22:35 +0000 (14:22 -0800)]
Merge branch 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of master.kernel.org:/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] 85xx: Enable CONFIG_SERIAL_8250_SHARE_IRQ
[POWERPC] Select u-image as default image for Linkstation
[POWERPC] 83xx: Minor fixes for 834x_mds USB setup code
[POWERPC] Fix warning in powermac pci.c
[POWERPC] Fix warning in powermac feature.c
[POWERPC] Fix warning in prom_parse.c of_irq_map_oldworld()
[POWERPC] Celleb: bug fix caused by not casting pointer types
[POWERPC] Add missing newline in xmon help output
[POWERPC] No DEEPNAP on 970MP 1.0
Olaf Kirch [Fri, 9 Mar 2007 21:55:38 +0000 (13:55 -0800)]
[IPV6]: Fix for ipv6_setsockopt NULL dereference
I came across this bug in http://bugzilla.kernel.org/show_bug.cgi?id=8155
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Gerrit Renker [Fri, 9 Mar 2007 21:47:58 +0000 (13:47 -0800)]
[DCCP]: Initialise write_xmit_timer also on passive sockets
The TX CCID needs the write_xmit_timer for delaying packet sends. Previously
this timer was only activated on active (connecting) sockets.
This patch initialises the write_xmit_timer in sync with the other timers, i.e.
the timer will be ready on any socket. This is used by applications with a
listening socket which start to stream after receiving an initiation by the
client. The write_xmit_timer is stopped when the application closes, as before.
Was tested to work and to remove the timer bug reported on dccp@vger.
Also moved timer initialisation into timer.c (static).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Fri, 9 Mar 2007 15:59:56 +0000 (15:59 +0000)]
[MIPS] Sibyte: Fix ZBbus profiler
o Fix build error.
o Handle error returns.
o Deal with signals received while sleeping.
o Don't allow to be selected when we're not building the directory with
the driver anyway.
o Coding style cleanups.
Linus Torvalds [Fri, 9 Mar 2007 18:34:55 +0000 (10:34 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
[JFFS2] print a message when marking bad block
[JFFS2] Check for all-zero node headers
[MTD] [OneNAND] Classify the page data and oob buffer
[MTD] [OneNAND] Exit the loop when transferring/filling of the oob is finished
[MTD] [OneNAND] add Nokia Copyright and a credit
[MTD] [OneNAND] Fix typo & wrong comments
[MTD] [OneNAND] Use oob buffer instead of main one in oob functions
[MTD] Correct partition failed erase address
[JFFS2] Use yield() between GC passes in background thread.
[MTD] [NAND] Correct misspelled preprocessor variable.
[MTD] [MAPS] dilnetpc: Fix printk warning
[MTD] [NOR] Fix oops in cfi_amdstd_sync
[MTD] ESB2 check for closed ROM window
[JFFS2] Fix writebuffer recovery in the first page of a block
[MTD] [NAND] make oobavail public
Linus Torvalds [Fri, 9 Mar 2007 18:12:46 +0000 (10:12 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
ibmtr: Drain rich supply of modpost warnings.
3c59x: Fix several modpost warnings
z85230: Fix FIFO handling
r8169: fix a race between PCI probe and dev_open
r8169: revert bogus BMCR reset
sky2: turn off Rx checksum on bad hardware
mv643xx: Clear pending interrupts before calling request_irq
myri10ge: add a wc_enabled flag to myri10ge_priv
myri10ge: prevent 4k rdma on SGI TIOCE chipset
myri10ge: use pci_map_page to prepare the dmatest buffer
myri10ge: fix error checking and return value in myri10ge_allocate_rings
netxen: fix warnings
via-rhine: set avoid_D3 for broken BIOSes
[PATCH] bcm43xx: Fix assertion failures in interrupt handler
[PATCH] bcm43xx: Fix bug in frequency to channel conversion
[PATCH] bcm43xx: Fix errors in specs to code translation in B6PHY init
Ralf Baechle [Thu, 8 Mar 2007 12:53:07 +0000 (12:53 +0000)]
ibmtr: Drain rich supply of modpost warnings.
Building ibmtr as a module produces a spectacular pile of modpost warnings:
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x450) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x454) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x458) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x45c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4e8) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4ec) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f0) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f4) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x500) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x504) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x508) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x50c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x520) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x524) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x528) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x534) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x540) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x544) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x548) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x54c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x558) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x55c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x560) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x564) and 'ibmtr_reset_timer'
Fix by making ibmtr_probe an __init function.
While at it, move move ibmtr_probe_card below ibmtr_probe so the protoype
for ibmtr_probe can be deleted.
Ralf Baechle [Thu, 8 Mar 2007 15:33:16 +0000 (15:33 +0000)]
3c59x: Fix several modpost warnings
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4580) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4584) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4588) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x458c) and 'vortex_eisa_remove'
Fixed by:
o move definition of vortex_eisa_driver below the functions it references.
o remove now unnecessary prototypes for vortex_eisa_probe and
vortex_eisa_remove.
o Make vortex_eisa_probe an __init function.
o Make vortex_eisa_remove a __devexit function.
o Wrap vortex_eisa_driver reference to vortex_eisa_remove with
__devexit_p().
Alan Cox [Wed, 7 Mar 2007 16:37:38 +0000 (16:37 +0000)]
z85230: Fix FIFO handling
We must exit immediately on a FIFO fill not take the end of packet path
otherwise each underrun in PIO transmit mode causes a runt packet and the
data is lost.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Yukon FE, occasional hardware receive checksum errors are seen.
An early indication of the problem is single bit differences in the two
checksum engines. Use this as a detection mechanism to turn off Rx
checksumming.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
projects / linux-2.6-omap-h63xx.git / log