Balazs Scheidler [Thu, 20 Nov 2008 09:07:24 +0000 (01:07 -0800)]
TPROXY: fill struct flowi->flags in udp_sendmsg()
udp_sendmsg() didn't fill struct flowi->flags, which means that
the route lookup would fail for non-local IPs even if the
IP_TRANSPARENT sockopt was set.
This prevents sendto() to work properly for UDP sockets, whereas
bind(foreign-ip) + connect() + send() worked fine.
Signed-off-by: Balazs Scheidler <bazsi@balabit.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 19 Nov 2008 23:52:41 +0000 (15:52 -0800)]
phylib: Fix auto-negotiation restart avoidance
A previous patch, 51e2a3846eab18711f4eb59cd0a4c33054e2980a, made
genphy_config_aneg() not restart aneg by calling genphy_restart_aneg() if
the advertisement hadn't changed.
But, genphy_restart_aneg() doesn't just restart aneg, it may also *enable*
aneg or un-isolate the PHY from the MII (those functions are controlled by
the same register). The code to avoid calling genphy_restart_aneg() didn't
consider this.
So, modify genphy_config_aneg() to also check if the PHY needs to have aneg
enabled or be un-isolated before deciding not to restart aneg.
This caused a problem with certain Davicom PHYs, as that driver isolates
the PHY (why?) before calling genphy_config_aneg() and expects the PHY to
be un-isolated by that function.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Reported-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Wed, 19 Nov 2008 23:50:59 +0000 (15:50 -0800)]
net: jme.c rxdesc.flags is __le16, other missing endian swaps
This is the minimal patch to fix endian mismatches. These are
probably bugs on big-endian arches, noops on little endian.
jme_rxsum_ok could be improved to directly take a __le16 and
change all of the masks/sets to be in little-endian, but
has not been done here to keep the patch small.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paulius Zaleckas [Wed, 19 Nov 2008 23:38:24 +0000 (15:38 -0800)]
phylib: fix phy name example in documentation
All MDIO bus drivers currently name bus with "%x" format.
There is one exception where mv643xx_eth driver is using "%d".
Phy address on the bus uses format "%02x".
Fixing phy name example to match all real life MDIO drivers.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 19 Nov 2008 23:33:54 +0000 (15:33 -0800)]
net: Do not fire linkwatch events until the device is registered.
Several device drivers try to do things like netif_carrier_off()
before register_netdev() is invoked. This is bogus, but too many
drivers do this to fix them all up in one go.
Reported-by: Folkert van Heusden <folkert@vanheusden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Wed, 19 Nov 2008 22:17:41 +0000 (14:17 -0800)]
phonet: fix compilation with gcc-3.4
CC [M] net/phonet/af_phonet.o
net/phonet/af_phonet.c: In function `pn_socket_create':
net/phonet/af_phonet.c:38: sorry, unimplemented: inlining failed in call to 'phonet_proto_put': function body not available
net/phonet/af_phonet.c:99: sorry, unimplemented: called from here
make[3]: *** [net/phonet/af_phonet.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Wed, 19 Nov 2008 22:17:02 +0000 (14:17 -0800)]
ixgbe: fix compilation with gcc-3.4
CC [M] drivers/net/ixgbe/ixgbe_main.o
drivers/net/ixgbe/ixgbe_main.c: In function `ixgbe_intr':
drivers/net/ixgbe/ixgbe_main.c:1290: sorry, unimplemented: inlining failed in call to 'ixgbe_irq_enable': function body not available
drivers/net/ixgbe/ixgbe_main.c:1312: sorry, unimplemented: called from here
make[4]: *** [drivers/net/ixgbe/ixgbe_main.o] Error 1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Wed, 19 Nov 2008 22:07:41 +0000 (14:07 -0800)]
net: fix ip_mr_init() error path
Similarly to IPv6 ip6_mr_init() (fixed last week), the order of cleanup
operations in the error/exit section of ip_mr_init() is completely
inversed. It should be the other way around.
Also a del_timer() is missing in the error path.
I should have guessed last week that this same error existed in ipmr.c
too, as ip6mr.c is largely inspired by ipmr.c.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 18 Nov 2008 16:07:51 +0000 (08:07 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: hold extra reference to bio in blk_rq_map_user_iov()
relay: fix cpu offline problem
Release old elevator on change elevator
block: fix boot failure with CONFIG_DEBUG_BLOCK_EXT_DEVT=y and nash
block/md: fix md autodetection
block: make add_partition() return pointer to hd_struct
block: fix add_partition() error path
Arjan van de Ven [Tue, 18 Nov 2008 14:56:51 +0000 (06:56 -0800)]
suspend: use WARN not WARN_ON to print the message
By using WARN(), kerneloops.org can collect which component is causing
the delay and make statistics about that. suspend_test_finish() is
currently the number 2 item but unless we can collect who's causing
it we're not going to be able to fix the hot topic ones..
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 18 Nov 2008 16:06:35 +0000 (08:06 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
kernel/profile.c: fix section mismatch warning
function tracing: fix wrong pos computing when read buffer has been fulfilled
tracing: fix mmiotrace resizing crash
ring-buffer: no preempt for sched_clock()
ring-buffer: buffer record on/off switch
Linus Torvalds [Tue, 18 Nov 2008 16:06:21 +0000 (08:06 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cpuset: fix regression when failed to generate sched domains
sched, signals: fix the racy usage of ->signal in account_group_xxx/run_posix_cpu_timers
sched: fix kernel warning on /proc/sched_debug access
sched: correct sched-rt-group.txt pathname in init/Kconfig
Linus Torvalds [Tue, 18 Nov 2008 16:06:00 +0000 (08:06 -0800)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
swiotlb: use coherent_dma_mask in alloc_coherent
MAINTAINERS: remove me as RAID maintainer
Linus Torvalds [Tue, 18 Nov 2008 16:05:43 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: fix a broken define in dma-mapping
Blackfin arch: fix bug - Turn on DEBUG_DOUBLEFAULT, booting SMP kernel crash
Blackfin arch: fix bug - shared lib function in L2 failed be called
Blackfin arch: fix incorrect limit check for bf54x check_gpio
Blackfin arch: fix bug - Cpufreq assumes clocks in kHz and not Hz.
Blackfin arch: dont warn when running a kernel on the oldest supported silicon
Blackfin arch: fix bug - kernel build with write back policy fails to be booted up
Blackfin arch: fix bug - dmacopy test case fail on all platform
Blackfin arch: Fix typo when adding CONFIG_DEBUG_VERBOSE
Blackfin arch: don't copy bss when copying L1
Blackfin arch: fix bug - Fail to boot jffs2 kernel for BF561 with SMP patch
Blackfin arch: handle case of d_path() returning error in decode_address()
Linus Torvalds [Tue, 18 Nov 2008 16:05:05 +0000 (08:05 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix resume of GPIO unsol event for STAC/IDT
ALSA: hda - Add quirks for HP Pavilion DV models
ALSA: hda - Fix GPIO initialization in patch_stac92hd71bxx()
ALSA: hda - Check model type instead of SSID in patch_92hd71bxx()
ALSA: sound/pci/pcxhr/pcxhr.c: introduce missing kfree and pci_disable_device
ALSA: hda: STAC_VREF_EVENT value change
ALSA: hda - Missing NULL check in hda_beep.c
ALSA: hda - Add digital beep playback switch for STAC/IDT codecs
Jens Axboe [Tue, 18 Nov 2008 14:07:05 +0000 (15:07 +0100)]
block: hold extra reference to bio in blk_rq_map_user_iov()
If the size passed in is OK but we end up mapping too many segments,
we call the unmap path directly like from IO completion. But from IO
completion we have an extra reference to the bio, so this error case
goes OOPS when it attempts to free and already free bio.
Fix it by getting an extra reference to the bio before calling the
unmap failure case.
Reported-by: Petr Vandrovec <vandrove@vc.cvut.cz> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Zhang, Yanmin [Fri, 14 Nov 2008 07:26:30 +0000 (08:26 +0100)]
block: fix boot failure with CONFIG_DEBUG_BLOCK_EXT_DEVT=y and nash
We run into system boot failure with kernel 2.6.28-rc. We found it on a
couple of machines, including T61 notebook, nehalem machine, and another
HPC NX6325 notebook. All the machines use FedoraCore 8 or FedoraCore 9.
With kernel prior to 2.6.28-rc, system boot doesn't fail.
I debug it and locate the root cause. Pls. see
http://bugzilla.kernel.org/show_bug.cgi?id=11899
https://bugzilla.redhat.com/show_bug.cgi?id=471517
As a matter of fact, there are 2 bugs.
1)root=/dev/sda1, system boot randomly fails. Mostly, boot for 5 times
and fails once. nash has a bug. Some of its functions misuse return
value 0. Sometimes, 0 means timeout and no uevent available. Sometimes,
0 means nash gets an uevent, but the uevent isn't block-related (for
exmaple, usb). If by coincidence, kernel tells nash that uevents are
available, but kernel also set timeout, nash might stops collecting
other uevents in queue if current uevent isn't block-related. I work
out a patch for nash to fix it.
http://bugzilla.kernel.org/attachment.cgi?id=18858
2) root=LABEL=/, system always can't boot. initrd init reports
switchroot fails. Here is an executation branch of nash when booting:
(1) nash read /sys/block/sda/dev; Assume major is 8 (on my desktop)
(2) nash query /proc/devices with the major number; It found line
"8 sd";
(3) nash use 'sd' to search its own probe table to find device (DISK)
type for the device and add it to its own list;
(4) Later on, it probes all devices in its list to get filesystem
labels; scsi register "8 sd" always.
When major is 259, nash fails to find the device(DISK) type. I enables
CONFIG_DEBUG_BLOCK_EXT_DEVT=y when compiling kernel, so 259 is picked up
for device /dev/sda1, which causes nash to fail to find device (DISK)
type.
To fixing issue 2), I create a patch for nash and another patch for
kernel.
Tejun Heo [Mon, 10 Nov 2008 06:29:58 +0000 (15:29 +0900)]
block: make add_partition() return pointer to hd_struct
Make add_partition() return pointer to the new hd_struct on success
and ERR_PTR() value on failure. This change will be used to fix md
autodetection bug.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Neil Brown <neilb@suse.de> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Rakib Mullick [Tue, 18 Nov 2008 04:15:24 +0000 (10:15 +0600)]
kernel/profile.c: fix section mismatch warning
Impact: fix section mismatch warning in kernel/profile.c
Here, profile_nop function has been called from a non-init function
create_hash_tables(void). Which generetes a section mismatch warning.
Previously, create_hash_tables(void) was a init function. So, removing
__init from create_hash_tables(void) requires profile_nop to be
non-init.
This patch makes profile_nop function inline and fixes the
following warning:
WARNING: vmlinux.o(.text+0x6ebb6): Section mismatch in reference from
the function create_hash_tables() to the function
.init.text:profile_nop()
The function create_hash_tables() references
the function __init profile_nop().
This is often because create_hash_tables lacks a __init
annotation or the annotation of profile_nop is wrong.
Li Zefan [Tue, 18 Nov 2008 06:02:03 +0000 (14:02 +0800)]
cpuset: fix regression when failed to generate sched domains
Impact: properly rebuild sched-domains on kmalloc() failure
When cpuset failed to generate sched domains due to kmalloc()
failure, the scheduler should fallback to the single partition
'fallback_doms' and rebuild sched domains, but now it only
destroys but not rebuilds sched domains.
The regression was introduced by:
| commit dfb512ec4834116124da61d6c1ee10fd0aa32bd6
| Author: Max Krasnyansky <maxk@qualcomm.com>
| Date: Fri Aug 29 13:11:41 2008 -0700
|
| sched: arch_reinit_sched_domains() must destroy domains to force rebuild
After the above commit, partition_sched_domains(0, NULL, NULL) will
only destroy sched domains and partition_sched_domains(1, NULL, NULL)
will create the default sched domain.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Max Krasnyansky <maxk@qualcomm.com> Cc: <stable@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
prevent cifs_writepages() from skipping unwritten pages
Fixed parsing of mount options when doing DFS submount
[CIFS] Fix check for tcon seal setting and fix oops on failed mount from earlier patch
[CIFS] Fix build break
cifs: reinstate sharing of tree connections
[CIFS] minor cleanup to cifs_mount
cifs: reinstate sharing of SMB sessions sans races
cifs: disable sharing session and tcon and add new TCP sharing code
[CIFS] clean up server protocol handling
[CIFS] remove unused list, add new cifs sock list to prepare for mount/umount fix
[CIFS] Fix cifs reconnection flags
[CIFS] Can't rely on iov length and base when kernel_recvmsg returns error
Dave Kleikamp [Tue, 18 Nov 2008 03:49:05 +0000 (03:49 +0000)]
prevent cifs_writepages() from skipping unwritten pages
Fixes a data corruption under heavy stress in which pages could be left
dirty after all open instances of a inode have been closed.
In order to write contiguous pages whenever possible, cifs_writepages()
asks pagevec_lookup_tag() for more pages than it may write at one time.
Normally, it then resets index just past the last page written before calling
pagevec_lookup_tag() again.
If cifs_writepages() can't write the first page returned, it wasn't resetting
index, and the next call to pagevec_lookup_tag() resulted in skipping all of
the pages it previously returned, even though cifs_writepages() did nothing
with them. This can result in data loss when the file descriptor is about
to be closed.
This patch ensures that index gets set back to the next returned page so
that none get skipped.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com> Acked-by: Jeff Layton <jlayton@redhat.com> Cc: Shirish S Pargaonkar <shirishp@us.ibm.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Igor Mammedov [Thu, 23 Oct 2008 09:58:42 +0000 (13:58 +0400)]
Fixed parsing of mount options when doing DFS submount
Since these hit the same routines, and are relatively small, it is easier to review
them as one patch.
Fixed incorrect handling of the last option in some cases
Fixed prefixpath handling convert path_consumed into host depended string length (in bytes)
Use non default separator if it is provided in the original mount options
Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Igor Mammedov <niallain@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Kumar Gala [Sat, 15 Nov 2008 18:02:34 +0000 (12:02 -0600)]
Remove -mno-spe flags as they dont belong
For some unknown reason at Steven Rostedt added in disabling of the SPE
instruction generation for e500 based PPC cores in commit 6ec562328fda585be2d7f472cfac99d3b44d362a.
We are removing it because:
1. It generates e500 kernels that don't work
2. its not the correct set of flags to do this
3. we handle this in the arch/powerpc/Makefile already
4. its unknown in talking to Steven why he did this
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Tested-and-Acked-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
rtnetlink: propagate error from dev_change_flags in do_setlink()
isdn: remove extra byteswap in isdn_net_ciscohdlck_slarp_send_reply
Phonet: refuse to send bigger than MTU packets
e1000e: fix IPMI traffic
e1000e: fix warn_on reload after phy_id error
phy: fix phy address bug
e100: fix dma error in direction for mapping
igb: use dev_printk instead of printk
qla3xxx: Cleanup: Fix link print statements.
igb: Use device_set_wakeup_enable
e1000: Use device_set_wakeup_enable
e1000e: Use device_set_wakeup_enable
via-velocity: enable perfect filtering for multicast packets
phy: Add support for Marvell 88E1118 PHY
mlx4_en: Pause parameters per port
phylib: fix premature freeing of struct mii_bus
atl1: Do not enumerate options unsupported by chip
atl1e: fix broken multicast by removing unnecessary crc inversion
gianfar: Fix DMA unmap invocations
net/ucc_geth: Fix oops in uec_get_ethtool_stats()
...
Oleg Nesterov [Mon, 17 Nov 2008 14:39:47 +0000 (15:39 +0100)]
sched, signals: fix the racy usage of ->signal in account_group_xxx/run_posix_cpu_timers
Impact: fix potential NULL dereference
Contrary to ad474caca3e2a0550b7ce0706527ad5ab389a4d4 changelog, other
acct_group_xxx() helpers can be called after exit_notify() by timer tick.
Thanks to Roland for pointing out this. Somehow I missed this simple fact
when I read the original patch, and I am afraid I confused Frank during
the discussion. Sorry.
Fortunately, these helpers work with current, we can check ->exit_state
to ensure that ->signal can't go away under us.
Also, add the comment and compiler barrier to account_group_exec_runtime(),
to make sure we load ->signal only once.
FUJITA Tomonori [Mon, 17 Nov 2008 07:24:34 +0000 (16:24 +0900)]
swiotlb: use coherent_dma_mask in alloc_coherent
Impact: fix DMA buffer allocation coherency bug in certain configs
This patch fixes swiotlb to use dev->coherent_dma_mask in
swiotlb_alloc_coherent().
coherent_dma_mask is a subset of dma_mask (equal to it most of
the time), enumerating the address range that a given device
is able to DMA to/from in a cache-coherent way.
But currently, swiotlb uses dev->dma_mask in alloc_coherent()
implicitly via address_needs_mapping(), but alloc_coherent is really
supposed to use coherent_dma_mask.
This bug could break drivers that uses smaller coherent_dma_mask than
dma_mask (though the current code works for the majority that use the
same mask for coherent_dma_mask and dma_mask).
Johannes Berg [Mon, 17 Nov 2008 07:20:31 +0000 (23:20 -0800)]
rtnetlink: propagate error from dev_change_flags in do_setlink()
Unlike ifconfig, iproute doesn't report an error when setting
an interface up fails:
(example: put wireless network mac80211 interface into repeater mode
with iwconfig but do not set a peer MAC address, it should fail with
-ENOLINK)
without patch:
# ip link set wlan0 up ; echo $?
0
#
with patch:
# ip link set wlan0 up ; echo $?
RTNETLINK answers: Link has been severed
2
#
Propagate the return value from dev_change_flags() to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net> Tested-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Layton [Sat, 15 Nov 2008 16:12:47 +0000 (11:12 -0500)]
cifs: reinstate sharing of tree connections
Use a similar approach to the SMB session sharing. Add a list of tcons
attached to each SMB session. Move the refcount to non-atomic. Protect
all of the above with the cifs_tcp_ses_lock. Add functions to
properly find and put references to the tcons.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Jeff Kirsher [Fri, 14 Nov 2008 06:45:23 +0000 (06:45 +0000)]
e1000e: fix IPMI traffic
Some users reported that they have machines with BMCs enabled that cannot
receive IPMI traffic after e1000e is loaded.
http://marc.info/?l=e1000-devel&m=121909039127414&w=2
http://marc.info/?l=e1000-devel&m=121365543823387&w=2
This fixes the issue if they load with the new parameter = 0 by disabling
crc stripping, but leaves the performance feature on for most users.
Based on work done by Hong Zhang.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Fri, 14 Nov 2008 06:45:07 +0000 (06:45 +0000)]
e1000e: fix warn_on reload after phy_id error
If the driver fails to initialize the first time due to the failure in the
phy_id check the kernel triggers a warn_on on the second try to load the
driver because the driver did not free the msi/x resources in the first
load because of the previous failure in phy_id check.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Helge Deller [Sun, 16 Nov 2008 23:30:57 +0000 (00:30 +0100)]
unitialized return value in mm/mlock.c: __mlock_vma_pages_range()
Fix an unitialized return value when compiling on parisc (with CONFIG_UNEVICTABLE_LRU=y):
mm/mlock.c: In function `__mlock_vma_pages_range':
mm/mlock.c:165: warning: `ret' might be used uninitialized in this function
Signed-off-by: Helge Deller <deller@gmx.de>
[ It isn't ever really used uninitialized, since no caller should ever
call this function with an empty range. But the compiler is correct
that from a local analysis standpoint that is impossible to see, and
fixing the warning is appropriate. ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Brown [Wed, 12 Nov 2008 16:34:02 +0000 (17:34 +0100)]
mfd: Correct WM8350 I2C return code usage
The vendor BSP used for the WM8350 development provided an I2C driver
which incorrectly returned zero on succesful sends rather than the
number of transmitted bytes, an error which was then propagated into the
WM8350 I2C accessors.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Linus Torvalds [Sun, 16 Nov 2008 18:09:34 +0000 (10:09 -0800)]
acpi: fix oops in acpi_system_wakeup_device_seq_show
Commit 0794469da3f7b2093575cbdfc1108308dd3641ce: ("ACPI: struct device -
replace bus_id with dev_name(), dev_set_name()") introduced a bug by
testing 'dev_name(ldev)' instead of 'ldev->bus' for NULL when printing
out the bus information.
Jesse Brandeburg [Fri, 14 Nov 2008 13:51:54 +0000 (13:51 +0000)]
e100: fix dma error in direction for mapping
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
igb_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since dev->power.should_wakeup bit is used by the PCI core to
decide whether the device should wake up the system from sleep
states, set/unset this bit whenever WOL is enabled/disabled using
e1000_set_wol(). Accordingly, use device_can_wakeup() for checking
if wake-up is supported by the device.
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
walimis [Sat, 15 Nov 2008 07:19:06 +0000 (15:19 +0800)]
function tracing: fix wrong pos computing when read buffer has been fulfilled
Impact: make output of available_filter_functions complete
phenomenon:
The first value of dyn_ftrace_total_info is not equal with
`cat available_filter_functions | wc -l`, but they should be equal.
root cause:
When printing functions with seq_printf in t_show, if the read buffer
is just overflowed by current function record, then this function
won't be printed to user space through read buffer, it will
just be dropped. So we can't see this function printing.
So, every time the last function to fill the read buffer, if overflowed,
will be dropped.
This also applies to set_ftrace_filter if set_ftrace_filter has
more bytes than read buffer.
fix:
Through checking return value of seq_printf, if less than 0, we know
this function doesn't be printed. Then we decrease position to force
this function to be printed next time, in next read buffer.
Another little fix is to show correct allocating pages count.
Ingo Molnar [Sun, 16 Nov 2008 07:07:15 +0000 (08:07 +0100)]
sched: fix kernel warning on /proc/sched_debug access
Luis Henriques reported that with CONFIG_PREEMPT=y + CONFIG_PREEMPT_DEBUG=y +
CONFIG_SCHED_DEBUG=y + CONFIG_LATENCYTOP=y enabled, the following warning
triggers when using latencytop:
Linus Torvalds [Sun, 16 Nov 2008 03:02:48 +0000 (19:02 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: don't grab devices with no input
HID: fix radio-mr800 hidquirks
HID: fix kworld fm700 radio hidquirks
HID: fix start/stop cycle in usbhid driver
HID: use single threaded work queue for hid_compat
HID: map macbook keys for "Expose" and "Dashboard"
HID: support for new unibody macbooks
HID: fix locking in hidraw_open()
Al Viro [Sat, 15 Nov 2008 01:15:43 +0000 (01:15 +0000)]
Fix inotify watch removal/umount races
Inotify watch removals suck violently.
To kick the watch out we need (in this order) inode->inotify_mutex and
ih->mutex. That's fine if we have a hold on inode; however, for all
other cases we need to make damn sure we don't race with umount. We can
*NOT* just grab a reference to a watch - inotify_unmount_inodes() will
happily sail past it and we'll end with reference to inode potentially
outliving its superblock.
Ideally we just want to grab an active reference to superblock if we
can; that will make sure we won't go into inotify_umount_inodes() until
we are done. Cleanup is just deactivate_super().
However, that leaves a messy case - what if we *are* racing with
umount() and active references to superblock can't be acquired anymore?
We can bump ->s_count, grab ->s_umount, which will almost certainly wait
until the superblock is shut down and the watch in question is pining
for fjords. That's fine, but there is a problem - we might have hit the
window between ->s_active getting to 0 / ->s_count - below S_BIAS (i.e.
the moment when superblock is past the point of no return and is heading
for shutdown) and the moment when deactivate_super() acquires
->s_umount.
We could just do drop_super() yield() and retry, but that's rather
antisocial and this stuff is luser-triggerable. OTOH, having grabbed
->s_umount and having found that we'd got there first (i.e. that
->s_root is non-NULL) we know that we won't race with
inotify_umount_inodes().
So we could grab a reference to watch and do the rest as above, just
with drop_super() instead of deactivate_super(), right? Wrong. We had
to drop ih->mutex before we could grab ->s_umount. So the watch
could've been gone already.
That still can be dealt with - we need to save watch->wd, do idr_find()
and compare its result with our pointer. If they match, we either have
the damn thing still alive or we'd lost not one but two races at once,
the watch had been killed and a new one got created with the same ->wd
at the same address. That couldn't have happened in inotify_destroy(),
but inotify_rm_wd() could run into that. Still, "new one got created"
is not a problem - we have every right to kill it or leave it alone,
whatever's more convenient.
So we can use idr_find(...) == watch && watch->inode->i_sb == sb as
"grab it and kill it" check. If it's been our original watch, we are
fine, if it's a newcomer - nevermind, just pretend that we'd won the
race and kill the fscker anyway; we are safe since we know that its
superblock won't be going away.
And yes, this is far beyond mere "not very pretty"; so's the entire
concept of inotify to start with.
Linus Torvalds [Sat, 15 Nov 2008 20:10:32 +0000 (12:10 -0800)]
Merge branch 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: Reorder the SCxTDR write after the TDxE clear.
sh: __copy_user function can corrupt the stack in case of exception
sh: Fixed the TMU0 reload value on resume
sh: Don't factor in PAGE_OFFSET for valid_phys_addr_range() check.
sh: early printk port type fix
i2c: fix i2c-sh_mobile rx underrun
sh: Provide a sane valid_phys_addr_range() to prevent TLB reset with PMB.
usb: r8a66597-hcd: fix wrong data access in SuperH on-chip USB
fix sci type for SH7723
serial: sh-sci: fix cannot work SH7723 SCIFA
sh: Handle fixmap TLB eviction more coherently.
A common reason for device drivers to implement their own printk macros
is the lack of a printk prefix with the standard pr_xyz macros.
Introduce a pr_fmt() macro that is applied for every pr_xyz macro to the
format string.
The most common use of the pr_fmt macro would be to add the name of the
device driver to all pr_xyz messages in a source file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 15 Nov 2008 19:38:41 +0000 (11:38 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (9624): CVE-2008-5033: fix OOPS on tvaudio when controlling bass/treble
V4L/DVB (9623): tvaudio: Improve debug msg by printing something more human
V4L/DVB (9622): tvaudio: Improve comments and remove a unneeded prototype
V4L/DVB (9621): Avoid writing outside shadow.bytes[] array
V4L/DVB (9620): tvaudio: use a direct reference for chip description
V4L/DVB (9619): tvaudio: update initial comments
V4L/DVB (9618): tvaudio: add additional logic to avoid OOPS
V4L/DVB (9617): tvtime: remove generic_checkmode callback
V4L/DVB (9616): tvaudio: cleanup - group all callbacks together
V4L/DVB (9615): tvaudio: instead of using a magic number, use ARRAY_SIZE
V4L/DVB (9613): tvaudio: fix a memory leak
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] dpt_i2o: fix transferred data length for scsi_set_resid()
[SCSI] scsi_error regression: Fix idempotent command handling
[SCSI] zfcp: Fix hexdump data in s390dbf traces
[SCSI] zfcp: fix erp timeout cleanup for port open requests
[SCSI] zfcp: Wait for port scan to complete when setting adapter online
[SCSI] zfcp: Fix cast warning
[SCSI] zfcp: Fix request list handling in error path
[SCSI] zfcp: fix mempool usage for status_read requests
[SCSI] zfcp: fix req_list_locking.
[SCSI] zfcp: Dont clear reference from SCSI device to unit
[SCSI] qla2xxx: Update version number to 8.02.01-k9.
[SCSI] qla2xxx: Return a FAILED status when abort mailbox-command fails.
[SCSI] qla2xxx: Do not honour max_vports from firmware for 2G ISPs and below.
[SCSI] qla2xxx: Use pci_disable_rom() to manipulate PCI config space.
[SCSI] qla2xxx: Correct Atmel flash-part handling.
[SCSI] megaraid: fix mega_internal_command oops
David Woodhouse [Fri, 14 Nov 2008 13:47:31 +0000 (13:47 +0000)]
Revert "x86: blacklist DMAR on Intel G31/G33 chipsets"
This reverts commit e51af6630848406fc97adbd71443818cdcda297b, which was
wrongly hoovered up and submitted about a month after a better fix had
already been merged.
The better fix is commit cbda1ba898647aeb4ee770b803c922f595e97731
("PCI/iommu: blacklist DMAR on Intel G31/G33 chipsets"), where we do
this blacklisting based on the DMI identification for the offending
motherboard, since sometimes this chipset (or at least a chipset with
the same PCI ID) apparently _does_ actually have an IOMMU.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| drivers/misc/c2port/core.c: In function 'c2port_reset':
| drivers/misc/c2port/core.c:73: error: dereferencing pointer to incomplete type
| drivers/misc/c2port/core.c: In function 'c2port_strobe_ck':
| drivers/misc/c2port/core.c:91: error: dereferencing pointer to incomplete type
Include <linux/sched.h> to fix it, as m68k's local_irq_enable() needs to know
about struct task_struct.
m68k: Fix off-by-one in m68k_setup_user_interrupt()
commit 69961c375288bdab7604e0bb1c8d22999bb8a347 ("[PATCH] m68k/Atari:
Interrupt updates") added a BUG_ON() with an incorrect upper bound
comparison, which causes an early crash on VME boards, where IRQ_USER is
8, cnt is 192 and NR_IRQS is 200.
Reported-by: Stephen N Chivers <schivers@csc.com.au> Tested-by: Kars de Jong <jongk@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Sat, 15 Nov 2008 18:28:54 +0000 (19:28 +0100)]
ALSA: hda - Check model type instead of SSID in patch_92hd71bxx()
Check board preset model instead of codec->subsystem_id in
patch_92hd71bxx() so that other hardwares configured via the model
option work like the given model.
Linus Torvalds [Sat, 15 Nov 2008 18:20:36 +0000 (10:20 -0800)]
Move "exit_robust_list" into mm_release()
We don't want to get rid of the futexes just at exit() time, we want to
drop them when doing an execve() too, since that gets rid of the
previous VM image too.
Doing it at mm_release() time means that we automatically always do it
when we disassociate a VM map from the task.
Reported-by: pageexec@freemail.hu Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Nick Piggin <npiggin@suse.de> Cc: Hugh Dickins <hugh@veritas.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Brad Spengler <spender@grsecurity.net> Cc: Alex Efros <powerman@powerman.name> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Fri, 14 Nov 2008 18:08:18 +0000 (19:08 +0100)]
ALSA: sound/pci/pcxhr/pcxhr.c: introduce missing kfree and pci_disable_device
Error handling code following a kzalloc should free the allocated data.
The error handling code is adjusted to call pci_disable_device(pci); as
well, as done later in the function
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
Matthew Ranostay [Fri, 14 Nov 2008 22:46:22 +0000 (17:46 -0500)]
ALSA: hda: STAC_VREF_EVENT value change
Changed value for STAC_VREF_EVENT from 0x40 to 0x00 because the
unsol response value is only 6-bits width and the former value
was 1<<6 which is an overrun.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[SCSI] dpt_i2o: fix transferred data length for scsi_set_resid()
dpt_i2o.c::adpt_i2o_to_scsi() reads the value at (reply+5) which
should contain the length in bytes of the transferred data. This
would be correct if reply was a u32 *. However it is a void * here,
so we need to read the value at (reply+20) instead.
The value at (reply+5) is usually 0xff0000, which is apparently
'large enough' and didn't cause any trouble until 2.6.27 where
caused this to become visible through e.g. iostat -x .
Signed-off-by: Miquel van Smoorenburg <mikevs@xs4all.net> Cc: Stable Tree <stable@kernel.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Jeff Layton [Fri, 14 Nov 2008 18:53:46 +0000 (13:53 -0500)]
cifs: reinstate sharing of SMB sessions sans races
We do this by abandoning the global list of SMB sessions and instead
moving to a per-server list. This entails adding a new list head to the
TCP_Server_Info struct. The refcounting for the cifsSesInfo is moved to
a non-atomic variable. We have to protect it by a lock anyway, so there's
no benefit to making it an atomic. The list and refcount are protected
by the global cifs_tcp_ses_lock.
The patch also adds a new routines to find and put SMB sessions and
that properly take and put references under the lock.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Tejun Heo [Thu, 13 Nov 2008 01:04:46 +0000 (10:04 +0900)]
libata: improve phantom device detection
Currently libata uses four methods to detect device presence.
1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine
Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe. In both cases, PHY status wasn't available. In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4. The other failed #2 but as it passed #3 and #4,
it still caused failure.
In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff Layton [Fri, 14 Nov 2008 18:44:38 +0000 (13:44 -0500)]
cifs: disable sharing session and tcon and add new TCP sharing code
The code that allows these structs to be shared is extremely racy.
Disable the sharing of SMB and tcon structs for now until we can
come up with a way to do this that's race free.
We want to continue to share TCP sessions, however since they are
required for multiuser mounts. For that, implement a new (hopefully
race-free) scheme. Add a new global list of TCP sessions, and take
care to get a reference to it whenever we're dealing with one.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Commit 46abc02175b3c246dd5141d878f565a8725060c9 ("phylib: give mdio
buses a device tree presence") added a call to device_unregister() in
a situation where the caller did not intend for the device to be
freed yet, but apart from just unregistering the device from the
system, device_unregister() does an additional put_device() that is
intended to free it.
The right function to use in this situation is device_del(), which
unregisters the device from the system like device_unregister() does,
but without dropping the reference count an additional time.
J. K. Cliburn [Sun, 9 Nov 2008 21:05:30 +0000 (15:05 -0600)]
atl1: Do not enumerate options unsupported by chip
Of the various WOL options provided in include/linux/ethtool.h, the
L1 NIC supports only magic packet. Remove all options except magic
packet from the atl1 driver.
Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
J. K. Cliburn [Tue, 11 Nov 2008 22:21:48 +0000 (16:21 -0600)]
atl1e: fix broken multicast by removing unnecessary crc inversion
Inverting the crc after calling ether_crc_le() is unnecessary and breaks
multicast. Remove it.
Tested-by: David Madore <david.madore@ens.fr> Signed-off-by: Jay Cliburn <jcliburn@gmail.com> Cc: stable@kernel.org Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
projects / linux-2.6-omap-h63xx.git / log