Fix sparse warnings in ixgb driver for net-2.6.24.
Added a sparse fix for invalid declaration using non-constant value
in ixgb_set_multi. Added a fix for the module param array index
and allows int params in the array. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dale Farnsworth [Mon, 29 Oct 2007 22:39:01 +0000 (15:39 -0700)]
mv643xx_eth: Fix MV643XX_ETH offsets used by Pegasos 2
In the mv643xx_eth driver, we now use offsets from the ethernet
register block within the chip, but the pegasos 2 platform still
needs offsets from the full chip's register base address.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Blackfin EMAC driver: Fix Ethernet communication bug (dupliated and lost packets)
Fix Ethernet communication bug(dupliated and lost packets)
in RMII PHY mode- dont call mac_disable and mac_enable during
10/100 REFCLK changes - mac_enable screws up the DMA descriptor chain
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Mon, 29 Oct 2007 19:12:34 +0000 (12:12 -0700)]
Merge branch 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: add hw link power management support
[libata] Link power management infrastructure
Linus Torvalds [Mon, 29 Oct 2007 19:11:54 +0000 (12:11 -0700)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: fix newly introduced host-reset bug
[libata] sata_nv: fix SWNCQ enabling
libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist
libata: no need to speed down if already at PIO0
libata: relocate forcing PIO0 on reset
pata_ns87415: define SUPERIO_IDE_MAX_RETRIES
[libata] Address some checkpatch-spotted issues
[libata] fix 'if(' and similar areas that lack whitespace
libata: implement ata_wait_after_reset()
libata: track SLEEP state and issue SRST to wake it up
libata: relocate and fix post-command processing
[libata] AHCI: add hw link power management support
This patch will set the correct bits to turn on Aggressive
Link Power Management (ALPM) for the ahci driver. This
will cause the controller and disk to negotiate a lower
power state for the link when there is no activity (see
the AHCI 1.x spec for details). This feature is mutually
exclusive with Hot Plug, so when ALPM is enabled, Hot Plug
is disabled. ALPM will be enabled by default, but it is
settable via the scsi host syfs interface. Possible
settings for this feature are:
Setting Effect
----------------------------------------------------------
min_power ALPM is enabled, and link set to enter
lowest power state (SLUMBER) when idle
Hot plug not allowed.
max_performance ALPM is disabled, Hot Plug is allowed
medium_power ALPM is enabled, and link set to enter
second lowest power state (PARTIAL) when
idle. Hot plug not allowed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Mon, 29 Oct 2007 14:49:28 +0000 (07:49 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
compat_ioctl: fix block device compat ioctl regression
[BLOCK] Fix bad sharing of tag busy list on queues with shared tag maps
Fix a build error when BLOCK=n
block: use lock bitops for the tag map.
cciss: update copyright notices
cfq_get_queue: fix possible NULL pointer access
blk_sync_queue() should cancel request_queue->unplug_work
cfq_exit_queue() should cancel cfq_data->unplug_work
block layer: remove a unused argument of drive_stat_acct()
Linus Torvalds [Mon, 29 Oct 2007 14:49:10 +0000 (07:49 -0700)]
Merge branch 'sg' of git://git.kernel.dk/linux-2.6-block
* 'sg' of git://git.kernel.dk/linux-2.6-block:
Correction of "Update drivers to use sg helpers" patch for IMXMMC driver
sg_init_table() should use unsigned loop index variable
sg_last() should use unsigned loop index variable
Initialise scatter/gather list in sg driver
Initialise scatter/gather list in ata_sg_setup
x86: fix pci-gart failure handling
SG: s390-scsi: missing size parameter in zfcp_address_to_sg()
SG: clear termination bit in sg_chain()
Al Viro [Mon, 29 Oct 2007 05:08:38 +0000 (05:08 +0000)]
deal with resource allocation bugs in arcmsr
a) for type B we should _not_ iounmap() acb->pmu; it's not ioremapped.
b) for type B we should iounmap() two regions we _do_ ioremap.
c) if ioremap() fails, we need to bail out (and clean up).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 29 Oct 2007 05:11:28 +0000 (05:11 +0000)]
fix abuses of ptrdiff_t
Use of ptrdiff_t in places like
- if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+ if (!access_ok(VERIFY_WRITE, (u8 __user *)
+ (ptrdiff_t) u_tmp->rx_buf,
+ u_tmp->len))
is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.
Use unsigned long or uintptr_t instead. There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 29 Oct 2007 05:08:48 +0000 (05:08 +0000)]
arcmsr: endianness bug
initializing a field in data shared with the card with
cpu_to_le32(something) | 0x100000 is broken - the field is, indeed,
little-endian and we need cpu_to_le32() on both parts.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 29 Oct 2007 05:03:23 +0000 (05:03 +0000)]
SCTP endianness annotations regression
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 29 Oct 2007 04:37:58 +0000 (04:37 +0000)]
SUNRPC endianness annotations
rpcrdma stuff lacks endianness annotations for on-the-wire data.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The conversion of handlers to compat_blkdev_ioctl accidentally
disabled handling of most ioctl numbers on block devices because
of a typo. Fix the one line to enable it all again.
Jens Axboe [Thu, 25 Oct 2007 08:14:47 +0000 (10:14 +0200)]
[BLOCK] Fix bad sharing of tag busy list on queues with shared tag maps
For the locking to work, only the tag map and tag bit map may be shared
(incidentally, I was just explaining this to Nick yesterday, but I
apparently didn't review the code well enough myself). But we also share
the busy list! The busy_list must be queue private, or we need a
block_queue_tag covering lock as well.
So we have to move the busy_list to the queue. This'll work fine, and
it'll actually also fix a problem with blk_queue_invalidate_tags() which
will invalidate tags across all shared queues. This is a bit confusing,
the low level driver should call it for each queue seperately since
otherwise you cannot kill tags on just a single queue for eg a hard
drive that stops responding. Since the function has no callers
currently, it's not an issue.
Emil Medve [Wed, 24 Oct 2007 12:18:32 +0000 (14:18 +0200)]
Fix a build error when BLOCK=n
mm/filemap.c: In function '__filemap_fdatawrite_range':
mm/filemap.c:200: error: implicit declaration of function
'mapping_cap_writeback_dirty'
This happens when we don't use/have any block devices and a NFS root
filesystem is used.
mapping_cap_writeback_dirty() is defined in linux/backing-dev.h which
used to be provided in mm/filemap.c by linux/blkdev.h until commit f5ff8422bbdd59f8c1f699df248e1b7a11073027 (Fix warnings with
!CONFIG_BLOCK).
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mike Miller [Wed, 24 Oct 2007 08:30:34 +0000 (10:30 +0200)]
cciss: update copyright notices
This patch updates the copyright information for the cciss driver. It
includes extending the year to 2007 (how timely) and some minor corrections
deemed necessary by HP legal and the Open Source Review Board. Please
consider this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
-------------------------------------------------------------------------------- Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Oleg Nesterov [Tue, 23 Oct 2007 13:08:21 +0000 (15:08 +0200)]
cfq_get_queue: fix possible NULL pointer access
cfq_get_queue()->cfq_find_alloc_queue() can fail, check the returned value.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Note that this isn't a bug at the moment, since the regular IO path
does not call this path without __GFP_WAIT set. However, it could be a
future bug, so I've applied it.
Jerome Marchand [Tue, 23 Oct 2007 13:05:46 +0000 (15:05 +0200)]
block layer: remove a unused argument of drive_stat_acct()
The nr_sector argument of drive_stat_acct() is not used anymore since the read and write sectors statistics are now updated in end_that_request_first(). This patch removes the useless argument.
Tejun Heo [Mon, 29 Oct 2007 07:45:05 +0000 (16:45 +0900)]
libata: no need to speed down if already at PIO0
After reset, transfer mode is always PIO0 regardless of
dev->xfer_mask. Check dev->pio_mode before trying to slow down after
configuration failure. This prevents bogus speed down before device
is actually configured.
Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 29 Oct 2007 07:41:09 +0000 (16:41 +0900)]
libata: relocate forcing PIO0 on reset
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 16 Oct 2007 21:21:24 +0000 (14:21 -0700)]
libata: implement ata_wait_after_reset()
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Thu, 25 Oct 2007 09:30:36 +0000 (18:30 +0900)]
libata: track SLEEP state and issue SRST to wake it up
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Bruce Allen <ballen@gravity.phys.uwm.edu> Cc: Andrew Paprocki <andrew@ishiboo.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Thu, 25 Oct 2007 09:22:44 +0000 (18:22 +0900)]
libata: relocate and fix post-command processing
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
eHEA resources that are allocated via H_CALLs have a unique identifier each.
These identifiers are necessary to free the resources. A reboot notifier
is used to free all eHEA resources before the indentifiers get lost, i.e
before kexec starts a new kernel.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Thu, 25 Oct 2007 20:58:03 +0000 (13:58 -0700)]
e1000e: Remove legacy jumbo frame receive code
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Thu, 25 Oct 2007 20:57:58 +0000 (13:57 -0700)]
e1000e: Re-enable SECRC - crc stripping
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Thu, 25 Oct 2007 20:57:53 +0000 (13:57 -0700)]
e1000e: Fix PBA calculation for jumbo frame packets
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Auke Kok [Thu, 25 Oct 2007 20:57:44 +0000 (13:57 -0700)]
e1000e: Fix jumbo frame receive code.
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Jeff Garzik [Fri, 26 Oct 2007 03:02:14 +0000 (23:02 -0400)]
[ISDN] capidrv: address two longstanding warnings
* change #warning to a code comment
* add comment and special ifdef'd 64-bit code for a situation where
we must store a pointer into a CAPI field 'Data', which is fixed by
the interface at 32 bits.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Acked-by: Karsten Keil <kkeil@suse.de>
Michael Ellerman [Mon, 29 Oct 2007 05:35:29 +0000 (16:35 +1100)]
Quieten hrtimer printk: "Switched to high resolution mode .."
Change the hrtimer printk "Switched to high resolution mode .." to
be KERN_DEBUG, rather than KERN_INFO. If users need to see this they
can pass "loglevel" or "debug" on the command line, or check dmesg.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
kernel/hrtimer.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Chuck Lever [Fri, 26 Oct 2007 17:29:48 +0000 (19:29 +0200)]
sg_init_table() should use unsigned loop index variable
Clean up: fix a mixed sign comparison in sg_init_table() accidentally
introduced by commit d6ec0842. The sign of the loop index variable
should match the sign of the "nents" argument.
Chuck Lever [Fri, 26 Oct 2007 17:29:47 +0000 (19:29 +0200)]
sg_last() should use unsigned loop index variable
Clean up: fix a mixed sign comparison in sg_last() accidentally
introduced by commit 70eb8040. The sign of the loop index variable
should match the sign of the "nents" argument.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
It looks like ata_sg_setup is working on an uninitialised sg table. Call
sg_init_table to initialise it before use.
Signed-off-by: Anton Blanchard <anton@samba.org>
Note: this patch will fix it, but you could also get away with just
doing the sg_init_table() once at qc creation time.
FUJITA Tomonori [Fri, 26 Oct 2007 11:56:24 +0000 (13:56 +0200)]
x86: fix pci-gart failure handling
blk_rq_map_sg doesn't initialize sg->dma_address/length to zero
anymore. Some low level drivers reuse sg lists without initializing so
IOMMUs might get non-zero dma_address/length. If map_sg fails, we need
pass the number of the mapped entries to gart_unmap_sg.
Francois Romieu [Sun, 21 Oct 2007 10:17:51 +0000 (12:17 +0200)]
ipg: missing Kconfig dependency
Fix for the error below while linking vmlinux:
[...]
drivers/built-in.o: In function `ipg_ioctl':
drivers/net/ipg.c:2148: undefined reference to `generic_mii_ioctl'
drivers/built-in.o: In function `ipg_get_settings':
drivers/net/ipg.c:2181: undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `ipg_set_settings':
drivers/net/ipg.c:2193: undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `ipg_nway_reset':
drivers/net/ipg.c:2205: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
Ken'ichi Ohmichi [Fri, 26 Oct 2007 05:19:26 +0000 (14:19 +0900)]
x86: Dump filtering supports x86_64 sparsemem
This patch adds the symbol "init_level4_pgt" to the vmcoreinfo data so
that makedumpfile (dump filtering command) supports x86_64 sparsemem
kernel of linux-2.6.24.
makedumpfile creates a small dumpfile by excluding unnecessary pages for
the analysis. It checks attributes in page structures and distinguishes
necessary pages and unnecessary ones. To check them, makedumpfile gets
the vmcoreinfo data which has the minimum debugging information only for
dump filtering.
For older x86_64 kernel (linux-2.6.23 or before), makedumpfile translates
the virtual address of page structure into physical address by subtracting
PAGE_OFFSET from virtual address, but this translation isn't effective for
linux-2.6.24 sparsemem kernel, because its page structures are in virtual
memmap area. makedumpfile should translate their virtual address by 4-levels
paging and it needs the symbol "init_level4_pgt".
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel only ever supports 1 version of the boot protocol
so there is no need to check the boot protocol revision to
see if a feature is supported.
Both x86 and x86_64 support the same boot protocol so we need
to implement the KEEP_SEGMENTS on x86_64 as well. It isn't
just paravirt bootloaders that could use this functionality.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Vivek Goyal <vgoyal@in.ibm.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Zachary Amsden <zach@vmware.com> Cc: Andi Kleen <ak@suse.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
James Bottomley [Fri, 26 Oct 2007 17:17:19 +0000 (12:17 -0500)]
x86: voyager: fix bogus conversion to per_cpu for boot_cpu_info
There were two problems. Firstly, someone forgot the struct keyword in
front of cpuinfo_x86, so I take it this wasn't even compile checked.
Secondly, the actual definition has this as a SHARED_ALIGNED, so the
definitions mismatch.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 27 Oct 2007 17:14:04 +0000 (10:14 -0700)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
[JFFS2] Update MAINTAINERS entry -- the jffs-dev list is dead
[JFFS2] Prevent return of initialised variable in jffs2_init_acl_post()
Linus Torvalds [Sat, 27 Oct 2007 17:12:39 +0000 (10:12 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc_spi: Fix mmc-over-spi regression
mmc: use common byte swap macros
mmc: fix cid and csd byte order
at91_mci: Fix bad reference
This patch fixes that regression by changing the scheme used to keep
from knowingly trying to use a shared bus segment, and updates the
adjacent comments slightly to better explain the issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
projects / linux-2.6-omap-h63xx.git / log