Samuel Ortiz [Thu, 6 Apr 2006 05:39:14 +0000 (22:39 -0700)]
[IRDA]: Support for Sigmatel STIR421x chip
This patch enables support for the Sigmatel's STIR421x IrDA chip.
Once patched with Sigmatel's firmware, this chip "almost" follows the
USB-IrDA spec. Thus this patch is against irda-usb.[ch].
The code has been tested by Nick Fedchik on an STIR4210 chipset based
dongle.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates the smcinit code into the smsc-ircc driver.
Some laptops have their smsc-ircc chip not properly configured by the
BIOS and needs some preconfiguration. Currently, this can be done from
userspace with smcinit, a utility that comes with the irda-utils
package. It messes with ioports and PCI settings, from userspace. Now
with this patch, if we happen to be on one of the known to be faulty
laptops, we preconfigure the chip from the driver.
Patch from Linus Walleij <triad@df.lth.se> Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Sesterhenn [Thu, 6 Apr 2006 05:28:14 +0000 (22:28 -0700)]
[BLUETOOTH] sco: Possible double free.
this fixes coverity bug id #1068.
hci_send_sco() frees skb if (skb->len > hdev->sco_mtu).
Since it returns a negative error value only in this case, we
can directly return here.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 4 Apr 2006 20:50:45 +0000 (13:50 -0700)]
[INET]: Move no-tunnel ICMP error to tunnel4/tunnel6
This patch moves the sending of ICMP messages when there are no IPv4/IPv6
tunnels present to tunnel4/tunnel6 respectively. Please note that for now
if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be
sent. This is similar to how we handle AH/ESP/IPCOMP.
This move fixes the bug where we always send an ICMP message when there is
no ip6_tunnel device present for a given packet even if it is later handled
by IPsec. It also causes ICMP messages to be sent when no IPIP tunnel is
present.
I've decided to use the "port unreachable" ICMP message over the current
value of "address unreachable" (and "protocol unreachable" by GRE) because
it is not ambiguous unlike the other ones which can be triggered by other
conditions. There seems to be no standard specifying what value must be
used so this change should be OK. In fact we should change GRE to use
this value as well.
Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel
where we don't check whether the embedded IPv6 header is present before
dereferencing it for the inside source address.
This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 4 Apr 2006 20:42:35 +0000 (13:42 -0700)]
[NETFILTER]: Fix fragmentation issues with bridge netfilter
The conntrack code doesn't do re-fragmentation of defragmented packets
anymore but relies on fragmentation in the IP layer. Purely bridged
packets don't pass through the IP layer, so the bridge netfilter code
needs to take care of fragmentation itself.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Olsson [Tue, 4 Apr 2006 19:53:35 +0000 (12:53 -0700)]
[FIB_TRIE]: Fix leaf freeing.
Seems like leaf (end-nodes) has been freed by __tnode_free_rcu and not
by __leaf_free_rcu. This fixes the problem. Only tnode_free is now
used which checks for appropriate node type. free_leaf can be removed.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Mon, 3 Apr 2006 06:34:19 +0000 (23:34 -0700)]
[SELINUX] Fix build after ipsec decap state changes.
security/selinux/xfrm.c: In function 'selinux_socket_getpeer_dgram':
security/selinux/xfrm.c:284: error: 'struct sec_path' has no member named 'x'
security/selinux/xfrm.c: In function 'selinux_xfrm_sock_rcv_skb':
security/selinux/xfrm.c:317: error: 'struct sec_path' has no member named 'x'
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move request_standard_resources() back to before PCI probing
This effectively undoes the PCI resource allocation changes done in
commit b408cbc704352eccee301e1103b23203ba1c3a0e, but leaves the cleanups
of that commit in place.
We're going back to marking the resources reported by e820 busy _before_
doing PCI probing, so that any PCI resource that clashes with the BIOS-
reported memory map will be reloacted to a non-clashing area.
The reason? Larry Finger reports that his laptop has the cardbus
controller set up by the BIOS so that it conflicts with the e820 memory
map, and needs to be relocated. See
http://bugzilla.kernel.org/show_bug.cgi?id=6337
for more details.
We'll have to work out how to handle the fbcon problem that caused that
commit in the first place in some other way.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Antonino A. Daplas <adaplas@pol.net> Cc: <bjk@luxsci.net> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
John Blackwood [Fri, 7 Apr 2006 17:50:25 +0000 (19:50 +0200)]
[PATCH] x86_64: Plug GS leak in arch_prctl()
In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:
- the current/calling task has NOT set its own gs base yet to a
non-zero value,
- some other task that ran on the same processor previously set their
own gs base to a non-zero value.
In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.
However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.
Change the arch_prctl() ARCH_GET_GS code to only read and return
the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
task is non-zero.
Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
a task can also setup a gs base value by using modify_ldt() and write
an index value into 'gs' from user space, the patch below reads
'gs' instead of using thread.gs, since in the modify_ldt() case,
the thread.gs value will be 0, and incorrect value would be returned
(the task->thread.gs value).
When the user has not set its own gs base value and the 'gs'
register is zero, then the MSR_KERNEL_GS_BASE register will not be
read and a value of zero will be returned by reading and returning
'task->thread.gs'.
The first patch shown below is an attempt at implementing this
approach.
Jordan Hargrave [Fri, 7 Apr 2006 17:50:18 +0000 (19:50 +0200)]
[PATCH] x86_64: Fix drift with HPET timer enabled
If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).
If HZ changes, this drift can become even more pronounced.
HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.
Vojtech comments:
"It's not entirely correct (it assumes the HPET ticks totally
exactly), but it's significantly better than assuming the PIT error
there."
The exception is reported in the SYSRET, not the next instruction.
This leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions
on this instruction.
This version of the patch has the teething problems that plagued an earlier
version fixed.
This is CVE-2006-0744
Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.
AMD systems have a modern APIC that supports 8 bit IDs, but
don't have a XAPIC version number. Add a new "modern_apic"
subfunction that handles this correctly and use it (nearly)
everywhere where XAPIC is tested for.
I removed one wart: the code specified that external APICs
would use an 8bit APIC ID. But I checked a real 82093 data sheet
and it says clearly that they only use 4bit. So I removed
this special case since it would a bit awkward to implement now.
I removed the valid APIC tests in mptable parsing completely. On any modern
system they only check against the full field width (8bit) anyways
and are no-ops. This also fixes them doing the wrong thing
on >8 core Opterons.
[PATCH] x86-64/i386: Don't process APICs/IO-APICs in ACPI when APIC is disabled.
When nolapic was passed or the local APIC was disabled
for another reason ACPI would still parse the IO-APICs
until these were explicitely disabled with noapic.
Usually this resulted in a non booting configuration unless
"nolapic noapic" was used.
I also disabled the local APIC parsing in this case, although
that's only cosmetic (suppresses a few printks)
[PATCH] x86_64: Don't sanity check Type 1 PCI bus access on newer systems
Horus systems don't have anything on bus 0 which makes
the Type 1 sanity checks fail. Use the DMI BIOS year to
check for newer systems and always assume Type 1 works on them.
I used 2001 as an pretty arbitary cutoff year.
[PATCH] i386/x86-64: Check that MCFG points to an e820 reserved area
This patch introduces a user for the e820_all_mapped function:
There have been several machines that don't have a working MMCONFIG,
often because of a buggy MCFG table in the ACPI bios. This patch adds a
simple sanity check that detects a whole bunch of these cases, and when
it detects it, linux now boots rather than crash-and-burns.
The accuracy of this detection can in principle be improved if there was
a "is this entire range in e820 with THIS attribute", but no such
function exist and the complexity needed for this is not really worth
it; this simple check already catches most cases anyway.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a e820_all_mapped() function which checks if the entire range
<start,end> is mapped with type.
This is done by moving the local start variable to the end of each
known-good region; if at the end of the function the start address is
still before end, there must be a part that's not of the correct type;
otherwise it's a good region.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] x86_64: Reserve SRAT hotadd memory on x86-64
From: Keith Mannthey, Andi Kleen
Implement memory hotadd without sparsemem. The memory in the SRAT
hotadd area is just preserved instead and can be activated later.
There are a few restrictions:
- Only one continuous hotadd area allowed per node
The main problem is dealing with the many buggy SRAT tables
that are out there. The strategy here is to reject anything
suspicious.
Originally from Keith Mannthey, with several hacks and changes by AK
and also contributions from Andrew Morton
[ TBD: Problems pointed out by KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>:
1) Goto's rebuild_zonelist patch will not work if CONFIG_MEMORY_HOTPLUG=n.
Rebuilding zonelist is necessary when the system has just memory <
4G at boot, and hot add memory > 4G. because x86_64 has DMA32,
ZONE_NORAML is not included into zonelist at boot time if system
doesn't have memory >4G at boot.
[AK: should just force the higher zones at boot time when SRAT tells us]
2) zone and node's spanned_pages and present_pages are not incremented.
They should be.
For example, our server (ia64/Fujitsu PrimeQuest) can equip memory
from 4G to 1T(maybe 2T in future), and SRAT will *always* say we have
possible 1T +memory. (Microsoft requires "write all possible memory
in SRAT") When we reserve memmap for possible 1T memory, Linux will
not work well in +minimum 4G configuraion ;)
[PATCH] x86_64: Support memory hotadd without sparsemem
Memory hotadd doesn't need SPARSEMEM, but can be handled by just preallocating
mem_maps. This only needs some untangling of ifdefs to enable the necessary
code even without SPARSEMEM.
Originally from Nick Piggin, just adapted to the newer branch.
You can't check PageLRU without holding zone->lru_lock. The page
release code can get away with it only because the page refcount is 0 at
that point. Also, you can't reliably remove pages from the LRU unless
the refcount is 0. Ever.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Jens Axboe <axboe@suse.de>
[PATCH] splice: page stealing needs to wait_on_page_writeback()
Thanks to Andrew for the good explanation of why this is so. akpm writes:
If a page is under writeback and we remove it from pagecache, it's still
going to get written to disk. But the VFS no longer knows about that page,
nor that this page is about to modify disk blocks.
So there might be scenarios in which those
blocks-which-are-about-to-be-written-to get reused for something else.
When writeback completes, it'll scribble on those blocks.
This won't happen in ext2/ext3-style filesystems in normal mode because the
page has buffers and try_to_release_page() will fail.
But ext2 in nobh mode doesn't attach buffers at all - it just sticks the
page in a BIO, finds some new blocks, points the BIO at those blocks and
lets it rip.
While that write IO's in flight, someone could truncate the file. Truncate
won't block on the writeout because the page isn't in pagecache any more.
So truncate will the free the blocks from the file under the page's feet.
Then something else can reallocate those blocks. Then write data to them.
Now, the original write completes, corrupting the filesystem.
[PATCH] splice: improve writeback and clean up page stealing
By cleaning up the writeback logic (killing write_one_page() and the manual
set_page_dirty()), we can get rid of ->stolen inside the pipe_buffer and
just keep it local in pipe_to_file().
This also adds dirty page balancing logic and O_SYNC handling.
* git://oss.sgi.com:8090/oss/git/xfs-2.6:
[XFS] Provide XFS support for the splice syscall.
[XFS] Reenable write barriers by default.
[XFS] Make project quota enforcement return an error code consistent with
[XFS] Implement the silent parameter to fill_super, previously ignored.
[XFS] Cleanup comment to remove reference to obsoleted function
* master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (28 commits)
[ALSA] Kconfig SND_SEQUENCER_OSS help text fix
[ALSA] Add Aux input switch control for Aureon Universe
[ALSA] pcxhr - Fix the crash with REV01 board
[ALSA] sound/pci/hda: use create_singlethread_workqueue()
[ALSA] hda-intel - Add support of ATI SB600
[ALSA] cs4281 - Fix the check of timeout in probe
[ALSA] cs4281 - Fix the check of right channel
[ALSA] Test volume resolution of usb audio at initialization
[ALSA] maestro3.c: fix BUG, optimization
[ALSA] HDA/Realtek: multiple input mux definitions and pin mode additions
[ALSA] AdLib FM card driver
[ALSA] Fix / clean up PCM-OSS setup hooks
[ALSA] Clean up PCM codes (take 2)
[ALSA] Tiny clean up of PCM codes
[ALSA] ISA drivers bailing on first !enable[i]
[ALSA] Remove obsolete kfree_nocheck call
[ALSA] Remove obsolete kfree_nocheck call
[ALSA] Add snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
[ALSA] Add snd-riptide driver for Conexant Riptide chip
[ALSA] hda-codec - Fix noisy output wtih AD1986A 3stack model
...
[PATCH] revert incorrect mutex conversion in hdaps driver
This reverts the mutex conversion that was recently done to the hdaps
driver; this coversion was buggy because the hdaps driver started using
this semaphore in IRQ context, which mutexes do not allow. Easiest
solution for now is to just revert the patch (the patch was part of a
bigger GIT commit, 9a61bf6300533d3b64d7ff29adfec00e596de67d but this
only reverts this one file)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (48 commits)
Documentation: fix minor kernel-doc warnings
BUG_ON() Conversion in drivers/net/
BUG_ON() Conversion in drivers/s390/net/lcs.c
BUG_ON() Conversion in mm/slab.c
BUG_ON() Conversion in mm/highmem.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/signal.c
BUG_ON() Conversion in kernel/ptrace.c
BUG_ON() Conversion in ipc/shm.c
BUG_ON() Conversion in fs/freevxfs/
BUG_ON() Conversion in fs/udf/
BUG_ON() Conversion in fs/sysv/
BUG_ON() Conversion in fs/inode.c
BUG_ON() Conversion in fs/fcntl.c
BUG_ON() Conversion in fs/dquot.c
BUG_ON() Conversion in md/raid10.c
BUG_ON() Conversion in md/raid6main.c
BUG_ON() Conversion in md/raid5.c
Fix minor documentation typo
BFP->BPF in Documentation/networking/tuntap.txt
...
Stefan Richter [Sat, 1 Apr 2006 19:11:41 +0000 (21:11 +0200)]
[PATCH] sbp2: fix spinlock recursion
sbp2util_mark_command_completed takes a lock which was already taken by
sbp2scsi_complete_all_commands. This is a regression in Linux 2.6.15.
Reported by Kristian Harms at
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=187394
[ More complete commentary, as response to questions by Andrew: ]
> This changes the call environment for all implementations of
> ->Current_done(). Are they all safe to call under this lock?
Short answer: Yes, trust me. ;-) Long answer:
The done() callbacks are passed on to sbp2 from the SCSI stack along
with each SCSI command via the queuecommand hook. The done() callback
is safe to call in atomic context. So does
Documentation/scsi/scsi_mid_low_api.txt say, and many if not all SCSI
low-level handlers rely on this fact. So whatever this callback does,
it is "self-contained" and it won't conflict with sbp2's internal ORB
list handling. In particular, it won't race with the
sbp2_command_orb_lock.
Moreover, sbp2 already calls the done() handler with
sbp2_command_orb_lock taken in sbp2scsi_complete_all_commands(). I
admit this is ultimately no proof of correctness, especially since this
portion of code introduced the spinlock recursion in the first place and
we didn't realize it since this code's submission before 2.6.15 until
now. (I have learned a lesson from this.)
I stress-tested my patch on x86 uniprocessor with a preemptible SMP
kernel (alas I have no SMP machine yet) and made sure that all code
paths which involve the sbp2_command_orb_lock were gone through multiple
times.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: kbuild infrastructure
IB/ipath: infiniband verbs support
IB/ipath: misc infiniband code, part 2
IB/ipath: misc infiniband code, part 1
IB/ipath: infiniband RC protocol support
IB/ipath: infiniband UC and UD protocol support
IB/ipath: infiniband header files
IB/ipath: layering interfaces used by higher-level driver code
IB/ipath: support for userspace apps using core driver
IB/ipath: sysfs and ipathfs support for core driver
IB/ipath: misc driver support code
IB/ipath: chip initialisation code, and diag support
IB/ipath: support for PCI Express devices
IB/ipath: support for HyperTransport devices
IB/ipath: core driver header files
IB/ipath: core device driver
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Wire up sys_sync_file_range() into syscall tables.
[SPARC]: Wire up sys_splice() into the syscall tables.
[SPARC64]: Update defconfig.
[SPARC64]: Align address in huge_pte_alloc().
[SPARC64]: Document the instruction checks we do in do_sparc64_fault().
[SPARC64]: Make tsb_sync() mm comparison more precise.
It doesn't make the splice itself necessarily nonblocking (because the
actual file descriptors that are spliced from/to may block unless they
have the O_NONBLOCK flag set), but it makes the splice pipe operations
nonblocking.
Pavel Pisa [Sun, 2 Apr 2006 18:27:07 +0000 (19:27 +0100)]
[ARM] 3457/1: i.MX: SD/MMC support for i.MX/MX1
Patch from Pavel Pisa
This patch adds support of i.MX/MX1 SD/MMC controller.
It has been significantly redesigned from the original Sascha Hauer's
version to support scatter-gather DMA, to conform to latest Pierre Ossman's
and Russell King's MMC-SD Linux 2.6.x infrastructure.
The handling of all events has been moved to the softirq context
and is designed with no busy-looping in mind. Unfortunately
some controller bugs has to be overcome by limited looping
about 2-20 usec but these are observed only for initial card
recognition phase.
There are still some missing/missed IRQs problems under heavy load.
Help of somebody with access to the full SDHC design information
is probably necessary.
Regenerated against 2.6.16-git-060402 to solve clash with other patches.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wim Van Sebroeck [Sun, 12 Feb 2006 16:44:57 +0000 (17:44 +0100)]
[WATCHDOG] pcwd.c general clean-up after patches
removal of includes (since we don't use kmalloc and
TASK_INTERRUPTABLE anymore).
Addition of missing commands.
Printk that lets the user know when the module was
unloaded.
Tony Lindgren [Sun, 2 Apr 2006 16:46:30 +0000 (17:46 +0100)]
[ARM] 3433/1: ARM: OMAP: 8/8 Update board files
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Sun, 2 Apr 2006 16:46:25 +0000 (17:46 +0100)]
[ARM] 3430/1: ARM: OMAP: 5/8 Update PM
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Sun, 2 Apr 2006 16:46:23 +0000 (17:46 +0100)]
[ARM] 3429/1: ARM: OMAP: 4/8 Update GPIO
Patch from Tony Lindgren
Update OMAP GPIO code from linux-omap tree:
- Fix omap16xx edge control by Juha Yrjola
- Support for additional omap16xx trigger modes by Dirk Behme
- Fix edge detection by Tony Lindgren et al.
- Better support for omap15xx and omap310 by Andrej Zaborowski
- Fix omap15xx interrupt bug by Petukhov Nikolay
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP pin multiplexing code from linux-omap tree.
This patch adds new pin configurations by various OMAP
developers, and suport for omap730 by Brian Swetland.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Sun, 2 Apr 2006 16:46:21 +0000 (17:46 +0100)]
[ARM] 3427/1: ARM: OMAP: 2/8 Update timers
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Sun, 2 Apr 2006 16:15:51 +0000 (17:15 +0100)]
[ARM] 3396/2: AT91RM9200 Platform devices update
Patch from Andrew Victor
This patch updates the platform device resources for the Ethernet and
MMC peripherals. It also adds platform device information for the NAND
(SmartMedia), I2C and the RTC.
(This version of the patch can be applied before Patch 3392/1)
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pavel Pisa [Sun, 2 Apr 2006 15:58:37 +0000 (16:58 +0100)]
[ARM] 3444/1: i.MX: Scatter-gather DMA emulation for i.MX/MX1
Patch from Pavel Pisa
This patch contains simplified set of changes to add scatter-gather
emulation capability into MX1 DMA support. The result should
be still usable for next combination of DMA transfers
Statter-Gather/linear/2D/FIFO to linear/2D/FIFO and
linear/2D/FIFO to Statter-Gather/2D/FIFO
The patch corrects channel priority allocation to be compatible
with MX1 hardware implementation.
Previous code has not been adapted from its PXA original.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6-omap-h63xx.git / log