Adrian Bunk [Sun, 29 Jul 2007 15:40:48 +0000 (12:40 -0300)]
V4L/DVB (5939): dvb-pll: make struct dvb_pll_fcv1236d static
The fcv1236d support patch was created before the "dvb: remove static
dependencies on dvb-pll" patch was applied, but the fcv1236d patch didn't
get merged until after the fact.
struct dvb_pll_fcv1236d can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Sun, 22 Jul 2007 12:39:56 +0000 (09:39 -0300)]
V4L/DVB (5918): ivtv: fix TV-out VBI handling, only reset on last close.
While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.
This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
V4L/DVB (5899): bttv: Fix Viewcast Osprey 440 support
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
V4L/DVB (5891): zr36067: Turn off raw capture properly
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5890): zr36067: Add UYVY, RGB555X, RGB565X, and RGB32 formats
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5888): zr36067: Driver was not returning correct image size
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (5886): zr36067: Fix problem setting norms
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
Reported by Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Simplified a bit as suggested by Rafael. -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Sun, 29 Jul 2007 07:50:42 +0000 (00:50 -0700)]
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
They are handled in a ->compat_ioctl() handler, so it's just noise
when compat_ioctl.c warns which occurs when they are used on non-SBUS
framebuffer devices.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 28 Jul 2007 05:39:14 +0000 (22:39 -0700)]
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
etc. etc. code sequence, basically replicating the provided
framebuffer_alloc()/framebuffer_release(), and doing it badly.
Not only is this massive code duplication, it also caused a
bug in that we weren't setting the fb_info->device pointer
which results in an OOPS when fb_is_primary_device() runs.
Fix all of this by using framebuffer_{alloc,release}() and
passing in "&of_device->dev" as the device pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Fortescue [Thu, 26 Jul 2007 07:17:22 +0000 (00:17 -0700)]
[PARTITION]: Sun/Solaris VTOC table corrections
Start doing VTOC validation before using its contents.
The validation is adjusted so as not to break existing setups
that do not set the VTOC version, sanity and partition count entries.
VTOC tables with more than 8 partitions will NOT be used.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Fortescue [Thu, 26 Jul 2007 06:45:10 +0000 (23:45 -0700)]
[SPARC]: Fix floppy on some sun4c systems.
Add in code to support an 82077 FDC on sun4c systems. There is a
problem with spurious interrupts but it does apear to work.
Testing on my SS2 (82072A FDC) shows that the floppy driver is not
100% with sun4c any way (any spurious interrupt kills it, requiring a
reboot to recover).
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 26 Jul 2007 06:30:16 +0000 (23:30 -0700)]
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty Russell [Mon, 30 Jul 2007 00:25:22 +0000 (10:25 +1000)]
Make lguest compile with CONFIG_BLOCK=n and CONFIG_NET=n
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Gabriel C <nix.or.die@googlemail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
Remove fs.h from mm.h. For this,
1) Uninline vma_wants_writenotify(). It's pretty huge anyway.
2) Add back fs.h or less bloated headers (err.h) to files that need it.
As result, on x86_64 allyesconfig, fs.h dependencies cut down from 3929 files
rebuilt down to 3444 (-12.3%).
Cross-compile tested without regressions on my two usual configs and (sigh):
Len Brown [Sat, 28 Jul 2007 07:33:16 +0000 (03:33 -0400)]
ACPI: restore CONFIG_ACPI_SLEEP
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_SUSPEND for suspend-to-Ram and standby
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Fri, 27 Jul 2007 03:42:52 +0000 (13:42 +1000)]
Provide timespec to guests rather than jiffies clock.
A non-periodic clock_event_device and the "jiffies" clock don't mix well:
tick_handle_periodic() can go into an infinite loop.
Currently lguest guests use the jiffies clock when the TSC is
unusable. Instead, make the Host write the current time into the lguest
page on every interrupt. This doesn't cost much but is more precise
and at least as accurate as the jiffies clock. It also gets rid of
the GET_WALLCLOCK hypercall.
Also, delay setting sched_clock until our clock is set up, otherwise
the early printk timestamps can go backwards (not harmful, just ugly).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rusty Russell [Fri, 27 Jul 2007 03:35:43 +0000 (13:35 +1000)]
Fix lguest bzImage loading with CONFIG_RELOCATABLE=y
Jason Yeh sent his crashing .config: bzImages made with
CONFIG_RELOCATABLE=y put the relocs where the BSS is expected, and we
crash with unusual results such as:
lguest: unhandled trap 14 at 0xc0122ae1 (0xa9)
Relying on BSS being zero was merely laziness on my part, and
unfortunately, lguest doesn't go through the normal startup path (which
does this in asm).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller [Sat, 28 Jul 2007 05:58:37 +0000 (22:58 -0700)]
Fix procfs compat_ioctl regression
It is important to only provide the compat_ioctl method
if the downstream de->proc_fops does too, otherwise this
utterly confuses the logic in fs/compat_ioctl.c and we
end up doing the wrong thing.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Alexey Dobriyan <adobriyan@sw.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 27 Jul 2007 13:23:44 +0000 (14:23 +0100)]
fix preprocessor idiocy in reiserfs
#x blocks expansion of macro argument, but it won't do you any
good if it's already been expanded... As it is, RFALSE(cond, ....)
ended up with stringified _expanded_ cond. Real fun when cond contains
something like le32_to_cpu() and you are on a big-endian box...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 27 Jul 2007 13:19:52 +0000 (14:19 +0100)]
more include order horrors
... because somebody had added preempt.h -> list.h, resulting in
asm/system.h -> hardirq.h -> preempt.h -> list.h -> asm/system.h on m68k,
with smp_wmb() used in list.h and defined in asm/system.h below the include
of hardirq.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Input Serio: Blackfin doesnt support I8042 - make sure it doesnt get selected
Blackfin arch: add BF54x I2C/TWI TWI0 driver support
Blackfin On-Chip RTC driver update for supporting BF54x
Blackfin Ethernet MAC driver: fix bug Report returned -ENOMEM upwards (in case L1/uncached memory alloc fails)
Blackfin arch: add error message when IRQ no available
Blackfin arch: Initialize the exception vectors early in the boot process
Blackfin arch: fix a compiling warning about dma-mapping
Blackfin arch: switch to using proper defines this time THREAD_SIZE and PAGE_SIZE instead of just PAGE_SIZE everywhere
Blackfin arch: fix bug which unaligns the init thread's stack and causes the current macro to fail.
Blackfin arch: Load P0 before storing through it
Blackfin arch: fix KGDB bug, dont forget last parameter.
Blackfin arch: add selections for BF544 and BF542
Blackfin arch: use bfin_read_SWRST() now that BF561 provides it
Blackfin arch: setup aliases for some core Core A MMRs
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
docbook: add pipes, other fixes
blktrace: use cpu_clock() instead of sched_clock()
bsg: Fix build for CONFIG_BLOCK=n
[patch] QUEUE_FLAG_READFULL QUEUE_FLAG_WRITEFULL comment fix
Removing processor.h removes the extern definition of
elf_hwcap, which fixes the link issue, but forgets cpu_relax().
So, instead, we'll call barrier() directly.
Cc: Lennert Buytenhek <kernel@wantstofly.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Acked-by: Ross Wille <wille@freescale.com> Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 4529/1: [HP Jornada 7XX] - Fix jornada720.c to use SSP driver
This fixes the jornada720.c file :
* ifdef for CONFIG_SA1100_JORNADA720_SSP since we dont want to include anything not selected in menyconfig.
* add documentation for init for future reference
* change platform driver name from jornada720_mcu ->
jornada_ssp.
* change maintainer in file.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
This patch adds a new file mptdebug.h in the fusion source directory,
which contains different debug macros. The existing debug macros and
flags are removed from the mptbase.h and Makefile In Kconfig a new
configuration parameter FUSION_LOGGING is added to enable/disable the
logging support during compile time.
signed-off-by: Sathya Prakash <sathya.prakash@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
In sas_smp_get_phy_events() we never test if the call to
alloc_smp_req(RPEL_REQ_SIZE) succeeds or fails. That means we run
the risk of dereferencing a NULL pointer if it does fail. Far
better to test if we got NULL back and in that case return -ENOMEM
just as we already do for the other memory allocation in that
function.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Paul Mundt [Sat, 28 Jul 2007 14:45:43 +0000 (23:45 +0900)]
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
BLK_DEV_BSG was added outside of the if BLOCK check, which allows it to
be enabled when CONFIG_BLOCK=n. This leads to many screenlengths of
errors, starting with a parse error on the request_queue_t definition.
Obviously this wasn't intended for CONFIG_BLOCK=n usage, so just move the
option back in to the block.
Caught with a randconfig on sh.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Jens Axboe <jens.axboe@oracle.com> Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Fri, 27 Jul 2007 14:29:26 +0000 (10:29 -0400)]
[SCSI] aacraid: fix Sunrise Lake reset handling
The patch is *much* smaller than the description. I am attempting to
answer to those that want to understand an issue that was reported in
May this year.
If a Sunrise Lake based card that requires an alternate reset mechanism
is set up to ignore the commanded IOP_RESET it reports 0x00000010
(IOP_RESET ignored) instead of 0x3803000F (use alternate reset mechanism
to reset all cores), and thus the reset platform function decides to
switch to IOP_RESET_ALWAYS because the reset platform function
parameters indicate that we *need* to reset the card. IOP_RESET_ALWAYS
then responds with the 0x3803000F return code, but alas we treat this as
an error instead of using the alternate reset mechanism (put a 0x03 into
the register offset 0x38). The reset fails, but the fact that the
IOP_RESET_ALWAYS command was issued has put the card in a purposeful
shutdown state in preparation for the alternate hardware reset to be
applied. Yuck.
IOP_RESET is ignored in internal production cards, typically to ensure
that we catch all adapter lockup issues without the driver progressing
further, so this would not appear to be a field issue and thus this
patch was destined to be only in the internal Adaptec source tree.
IOP_RESET_ALWAYS is reserved for
kexec/kdump/FirmwareUpdate/AutomatedTestFrames so we did not function as
expected in any case. Also in the past we have had OEMs specifically
request that cards not be resetable after a BlinkLED/FirmwareAssert for
one reason or another and To head off the possibility that the Sunrise
Lake based cards would suffer a similar fate, we propose the enclosed
fix.
Yinghai Lu of SUN had a pre-production card with IOP_RESET disabled when
he reported an issue to the linux kernel list back in May regarding a
kexec problem resulting from this reset being ignore. His fix was to
update the Firmware to one that did not ignore the IOP_RESET. Previous
kernels did not attempt to reset the adapter and that is why it surfaced
as a regression in his hands.
The current list of aacraid based cards that use Sunrise Lake:
9005:0285:9005:02b5 Adaptec 5445
9005:0285:9005:02b6 Adaptec 5805
9005:0285:9005:02b7 Adaptec 5085
9005:0285:9005:02c3 Adaptec 51205
9005:0285:9005:02c4 Adaptec 51605
9005:0285:9005:02ce Adaptec 51245
9005:0285:9005:02cf Adaptec 51645
9005:0285:9005:02d0 Adaptec 52445
9005:0285:9005:02d1 Adaptec 5405
9005:0285:9005:02b8 ICP ICP5445SL
9005:0285:9005:02b9 ICP ICP5085SL
9005:0285:9005:02ba ICP ICP5805SL
9005:0285:9005:02c5 ICP ICP5125SL
9005:0285:9005:02c6 ICP ICP5165SL
9005:0285:108e:7aac SUN STK RAID REM
9005:0285:108e:0286 SUN STK RAID INT
9005:0285:108e:0287 SUN STK RAID EXT
9005:0285:108e:7aae SUN STK RAID EM
All of these are publicly released with IOP_RESET enabled. So there is
no immediate need for this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Fri, 27 Jul 2007 13:48:49 +0000 (09:48 -0400)]
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
Customer running an application that issues SYNCHRONIZE_CACHE calls
directly noticed the broad stroke of the current implementation in the
aacraid driver resulting in multiple applications feeding I/O to the
storage causing the issuing application to stall for long periods of
time. By only waiting for the current WRITE commands, rather than all
commands, to complete; and those that are in range of the
SYNCHRONIZE_CACHE call that would associate more tightly with the
issuing application before telling the Firmware to flush it's dirty
cache, we managed to reduce the stalling. The Firmware itself still
flushes all the dirty cache associated with the array ignoring the
range, it just does so in a more timely manner.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Tony Luck [Fri, 27 Jul 2007 22:35:43 +0000 (15:35 -0700)]
[IA64] Fix build failure in fs/quota.c
b716395e2b8e450e294537de0c91476ded2f0395 added code to handle
a compatability issue with 32bit quota tools, but the new compat
routines are only needed when CONFIG_COMPAT=y (and with this set
to 'n' there are compilation problems since some new typedefs are
not visible).
Reported by Doug Chapman. Fix tuned by a cast of thousands (Andi,
Andreas, Arthur, HPA, Willy)
Acked-by: Myron Stowe <myron.stowe@hp.com> Acked-by: Len Brown <len.brown@intel.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Tony Luck <tony.luck@intel.com>
Matthew Wilcox [Thu, 26 Jul 2007 14:56:23 +0000 (10:56 -0400)]
[SCSI] advansys: lindent and other large, uninteresting changes
- Run Lindent
- Move advansys_detect and advansys_release to the end of the file
- Split advansys_board_found out of advansys_detect
- Rename a few variables, such as shp to shost and pci_devp to pdev
- Turn STATIC into static
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wide transfers are required for every setting of PPR apart from QAS.
It seems the DV code starts at the minimum, which turns on DT and Wide
regardless of the setting of max_width. Redo the PPR and period
setting routines to respect max_width (i.e. start at period = 10 if it
is zero).
This fixes bugzilla 8366
Acked-by: "Freels, James D." <freelsjd@ornl.gov> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Seokmann Ju [Thu, 26 Jul 2007 20:43:34 +0000 (13:43 -0700)]
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
This is a patch to fix 'segmentation fault' issue which was initiated
by Richard Lary <rlary@us.ibm.com>. Thanks again Richard.
- on following sysfs attritute function, changes have made so that both
count and offset input parameters are honored by the functions.
= qla2x00_sysfs_read_nvram()
= qla2x00_sysfs_read_vpd()
- made changes so that NVRAM data to be cached to minimize H/W accesses
during agent querying of the driver's.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Thu, 26 Jul 2007 18:20:02 +0000 (14:20 -0400)]
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
Minor unimportant cuttings from the floor bundled in with a version
stamp update. Only controversial change is the dropping of Alan Cox
copyright on the nark.c module since that file has no code written by
him in it.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:47 +0000 (12:46 -0500)]
[SCSI] iscsi_tcp: Turn off bounce buffers
It was found by LSI that on setups with large amounts of memory
we were bouncing buffers when we did not need to. If the iscsi tcp
code touches the data buffer (or a helper does),
it will kmap the buffer. iscsi_tcp also does not interact with hardware,
so it does not have any hw dma restrictions. This patch sets the bounce
buffer settings for our device queue so buffers should not be bounced
because of a driver limit.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:48 +0000 (12:46 -0500)]
[SCSI] libiscsi: fix cmd seqeunce number checking
We should not be checking the cmd windown for just handling r2t responses.
And if the window closes in on us, always have scsi-ml requeue the command
from our queuecommand function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:46 +0000 (12:46 -0500)]
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:45 +0000 (12:46 -0500)]
[SCSI] libiscsi: make sure session is not blocked when removing host
When we logout we block the session since we are not taking any more
commands, but when we call remove host we want to make sure any
IO that got queued up and blocked gets failed upwards quickly, so
we unblock the session and fail it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a machine check is pending and the external or I/O interrupt handler
returns to userspace io_mcck_pending is going to call s390_handle_mcck.
Before this happens a call to TRACE_IRQS_ON was already made since we
know that we are going back to userspace and hence interrupts will be
enabled. So there was an indication that interrupts are enabled while
in reality they are still disabled.
s390_handle_mcck will do a local_irq_save/restore pair and confuse
lockdep which later complains about inconsistent irq tracing.
To solve this just call trace_hardirqs_off before calling
s390_handle_mcck and trace_hardirqs_on afterwards.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch implements support of fallocate system call on s390(x)
platform. A wrapper is added to address the issue which s390 ABI has with
the arguments of this system call.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The header file for external interrupts uses the _u16 type. Make sure
that _u16 is defined by including linux/types.h. This prevents compile
failures, if asm/s390_ext.h is the first include file.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no need to disable bottom halves when holding call_lock. Also
this could imply that it is legal to call smp_call_function* from
bh context, which it is not.
Also test if func will be executed locally before disabling
and aterwards enabling interrupts again. It's not necessary to disable
and enable interrupts each time __smp_call_function_map gets called.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_call_function_single now has the same semantics as s390's
smp_call_function_on. Therefore convert to the *single variant
and get rid of some architecture specific code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
projects / linux-2.6-omap-h63xx.git / log