Daniel Drake [Wed, 9 May 2007 23:32:24 +0000 (00:32 +0100)]
USB: add USB_DEVICE_AND_INTERFACE_INFO for device matching
Recently, the USB device matching code stopped matching generic interface
matches against devices with vendor-specific device class values.
Some drivers now need to explicitly match USB device ID's (in addition to
generic interface info) to retain the same behaviour as before. This new macro,
suggested by Alan Stern, makes the explicit device/interface matching a little
simpler for those users.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 9 May 2007 04:01:30 +0000 (21:01 -0700)]
USB: usb gadget, dead config cleanup
Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dave Platt [Tue, 8 May 2007 18:00:12 +0000 (11:00 -0700)]
USB: RTS/CTS handshaking support, DTR fixes for MCT U232 serial adapter
Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control. Implement HUPCL. Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: Dave Platt <dplatt@radagast.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arjan van de Ven [Tue, 22 May 2007 19:42:56 +0000 (12:42 -0700)]
USB: Patch to align the various USB timers to fire at the same time
This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: Martin K. Petersen <mkp@mkp.net> Signed-off-by: Mike Swift <mikes@digi.com> Signed-off-by: Jeremy McBane <jmcbane@digi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:54 +0000 (11:55 -0400)]
USB: Make device reset stop retrying after disconnect
This patch (as898) changes the port reset code in the hub driver. If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).
It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:31 +0000 (11:55 -0400)]
USB: EHCI: fix handover for designated full-speed ports
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility. A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:03 +0000 (11:53 -0400)]
USB: add RESET_RESUME device quirk
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:40 +0000 (11:52 -0400)]
USB: EHCI, OHCI: handover changes
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:20 +0000 (11:52 -0400)]
USB: add USB-Persist facility
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 3 May 2007 23:51:16 +0000 (16:51 -0700)]
usbmon: Add class for binary interface
Add a class which allows for an easier integration with udev.
This code was originally written by Paolo Abeni, and arrived to my tree
as a part of big patch to add binary API on December 18. As I understand,
Paolo always meant the class to be a part of the whole thing. This is his
udev rule to go along with the patch:
Kees Lemmens [Tue, 27 Mar 2007 10:34:30 +0000 (12:34 +0200)]
USB: oti6858 usb-serial driver (in Nokia CA-42 cable)
Last week I've been searching for a driver for the CA-42 cable (see usb
below) that fitted my kernel 2.6.20. I only found an abandoned version for a
driver on your website that indeed worked on 2.6.18 but wouldn't even
compile with a more recent 2.6.20 kernel.
I fiddled 2 evenings with the kernel code and have patched it up now to work
with the modifications in the 2.6.20 kernel. The patch is attached hereafter
and it works fine (at least for me :-) ).
Bus 2 Device 13: ID 0ea0:6858 Ours Technology, Inc.
I had to fiddle a little with the settings in .gnokiirc but that also
occurred with the older 2.6.18 kernel. Nevertheless, on one system with this
cable and my Nokia 6070 I had best results with :
model = 6510
connection = dku5
while on an other system with the same kernel, cable and phone it only worked
with :
model = AT
connection = serial
serial_write_usleep = 1
David Brownell [Thu, 17 May 2007 19:21:19 +0000 (12:21 -0700)]
USB: ehci refcounts work on ppc7448
Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Engelhardt [Fri, 11 May 2007 06:04:13 +0000 (23:04 -0700)]
USB: Use menuconfig objects
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:11 +0000 (11:55 -0400)]
USB: make hub driver's release more robust
This revised patch (as893c) improves the method used by the hub driver
to release its private data structure. The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed. The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:50 +0000 (11:54 -0400)]
USB: remove "locktree" routine from the hub driver
This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:28 +0000 (11:54 -0400)]
USB: remove references to dev.power.power_state
This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state. This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:30 +0000 (11:53 -0400)]
USB: don't unsuspend for a new connection
This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection. For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically. For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:54 +0000 (11:51 -0400)]
USB: move bus_suspend and bus_resume method calls
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.
Their old locations were not fully correct. For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:
echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind
to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub. Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.
The patch also makes a very slight change in the way devices with no
driver are handled during suspend. Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called. In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:25 +0000 (11:51 -0400)]
USB: Implement PM FREEZE and PRETHAW
This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events. Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state. The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:49:57 +0000 (11:49 -0400)]
USB: interface PM state
This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea. In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: r8a66597-hcd: host controller driver for R8A66597
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Simon Arlott [Fri, 11 May 2007 06:04:11 +0000 (23:04 -0700)]
USB: cxacru: Cleanup sysfs attribute code
This changes the format of unknown status values to be less verbose and
uses an array instead of several different snprintf calls. Since only
enum values are assigned to it, poll_state is changed from int to enum.
Use abs() for dB values instead of two almost identical return lines.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Acked-by: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Roese [Tue, 1 May 2007 16:29:37 +0000 (09:29 -0700)]
USB: EHCI support for big-endian descriptors
This patch implements supports for EHCI controllers whose in-memory
data structures are represented in big-endian format. This is needed
(unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI
spec doesn't specify little-endian format, although that's what most
other implementations use.
The guts of the patch are to introduce the hc32 type and change all
references from le32 to hc32. All access routines are converted from
cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other
"direction". (This is the same approach used with OHCI.)
David fixed:
Whitespace fixes; refresh against ehci cpufreq patch; move glue
for that PPC driver to the patch adding it; fix free symbol
capture bugs in modified "constant" macros; and make "hc32" etc
be "le32" unless we really need the BE options, so "sparse" can
do some real good.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI controllers that don't cache enough microframes can get MMF errors
when CPU frequency changes occur between the start and completion of
split interrupt transactions, due to delays in reading main memory
(caused by CPU cache snoop delays).
This patch adds a cpufreq notifier to the EHCI driver that will
inactivate split interrupt transactions during frequency transitions.
It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI
controllers.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:15 +0000 (17:29 +0100)]
dm raid1: handle log failure
When writing to a mirror, the log must be updated first. Failure
to update the log could result in the log not properly reflecting
the state of the mirror if the machine should crash.
We change the return type of the rh_flush function to give us
the ability to check if a log write was successful. If the
log write was unsuccessful, we fail the writes to avoid the
case where the log does not properly reflect the state of the
mirror.
A follow-up patch - which is dependent on the ability to
requeue I/O's to core device-mapper - will requeue the I/O's
for retry (allowing the mirror to be reconfigured.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)]
dm raid1: handle resync failures
Device-mapper mirroring currently takes a best effort approach to
recovery - failures during mirror synchronization are completely ignored.
This means that regions are marked 'in-sync' and 'clean' and removed
from the hash list. Future reads and writes that query the region
will incorrectly interpret the region as in-sync.
This patch handles failures during the recovery process. If a failure
occurs, the region is marked as 'not-in-sync' (aka RH_NOSYNC) and added
to a new list 'failed_recovered_regions'.
Regions on the 'failed_recovered_regions' list are not marked as 'clean'
upon removal from the list. Furthermore, if the DM_RAID1_HANDLE_ERRORS
flag is set, the region is marked as 'not-in-sync'. This action prevents
any future read-balancing from choosing an invalid device because of the
'not-in-sync' status.
If "handle_errors" is not specified when creating a mirror (leaving the
DM_RAID1_HANDLE_ERRORS flag unset), failures will be ignored exactly as they
would be without this patch. This is to preserve backwards compatibility with
user-space tools, such as 'pvmove'. However, since future read-balancing
policies will rely on the correct sync status of a region, a user must choose
"handle_errors" when using read-balancing.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Bader [Thu, 12 Jul 2007 16:28:33 +0000 (17:28 +0100)]
dm: disable barriers
This patch causes device-mapper to reject any barrier requests. This is done
since most of the targets won't handle this correctly anyway. So until the
situation improves it is better to reject these requests at the first place.
Since barrier requests won't get to the targets, the checks there can be
removed.
Cc: stable@kernel.org Signed-off-by: Stefan Bader <shbader@de.ibm.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jonathan Brassow [Thu, 12 Jul 2007 16:28:25 +0000 (17:28 +0100)]
dm raid1: clear region outside spinlock
A clear_region function is permitted to block (in practice, rare) but gets
called in rh_update_states() with a spinlock held.
The bits being marked and cleared by the above functions are used
to update the on-disk log, but are never read directly. We can
perform these operations outside the spinlock since the
bits are only changed within one thread viz.
- mark_region in rh_inc()
- clear_region in rh_update_states().
So, we grab the clean_regions list items via list_splice() within the
spinlock and defer clear_region() until we iterate over the list for
deletion - similar to how the recovered_regions list is already handled.
We then move the flush() call down to ensure it encapsulates the changes
which are done by the later calls to clear_region().
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:13 +0000 (17:28 +0100)]
dm snapshot: permit invalid activation
Allow invalid snapshots to be activated instead of failing.
This allows userspace to reinstate any given snapshot state - for
example after an unscheduled reboot - and clean up the invalid snapshot
at its leisure.
Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:28:00 +0000 (17:28 +0100)]
dm snapshot: fix invalidation deadlock
Process persistent exception store metadata IOs in a separate thread.
A snapshot may become invalid while inside generic_make_request().
A synchronous write is then needed to update the metadata while still
inside that function. Since the introduction of
md-dm-reduce-stack-usage-with-stacked-block-devices.patch this has to
be performed by a separate thread to avoid deadlock.
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Milan Broz [Thu, 12 Jul 2007 16:27:24 +0000 (17:27 +0100)]
dm raid1: fix status
Fix mirror status line broken in dm-log-report-fault-status.patch:
- space missing between two words
- placeholder ("0") required for compatibility with a subsequent patch
- incorrect offset parameter
Cc: stable@kernel.org Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use new KMEM_CACHE() macro and make the newly-exposed structure names more
meaningful. Also remove some superfluous casts and inlines (let a modern
compiler be the judge).
Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (50 commits)
[ARM] sa1100: remove boot time RTC initialisation
[ARM] sa1100: stop doing our own rtc management over suspend
[ARM] 4474/1: Do not check the PSR_F_BIT in valid_user_regs
[ARM] 4473/2: Take the HWCAP definitions out of the elf.h file
[ARM] pxa: move platform devices to separate header file
[ARM] pxa: move device registration into CPU-specific file
[ARM] pxa: remove boot time RTC initialisation
[ARM] pxa: stop doing our own rtc management over suspend
[ARM] 4451/1: pxa: make dma.c generic and remove cpu specific dma code
[ARM] 4450/1: pxa: add pxa25x_init_irq() and pxa27x_init_irq()
[ARM] 4440/1: PXA: enable the checking of ICIP2 for IRQs
[ARM] 4438/1: PXA: remove #ifdef .. #endif from pxa_gpio_demux_handler()
[ARM] 4437/1: PXA: move the GPIO IRQ initialization code to pxa_init_irq_gpio()
[ARM] 4436/1: PXA: move low IRQ initialization code to pxa_init_irq_low()
[ARM] 4435/1: PXA: remove PXA_INTERNAL_IRQS
[ARM] 4434/1: PXA: remove PXA_IRQ_SKIP
[ARM] pxa: Fix PXA27x suspend type validation, remove pxa_pm_prepare()
[ARM] pxa: move pm_ops structure into CPU specific files
[ARM] pxa: introduce cpu_is_pxaXXX macros
[ARM] pxa: remove MMC register defines from pxa-regs.h
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
security: unexport mmap_min_addr
SELinux: use SECINITSID_NETMSG instead of SECINITSID_UNLABELED for NetLabel
security: Protection for exploiting null dereference using mmap
SELinux: Use %lu for inode->i_no when printing avc
SELinux: allow preemption between transition permission checks
selinux: introduce schedule points in policydb_destroy()
selinux: add selinuxfs structure for object class discovery
selinux: change sel_make_dir() to specify inode counter.
selinux: rename sel_remove_bools() for more general usage.
selinux: add support for querying object classes and permissions from the running policy
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix sysfs_create_file return value handling
[CPUFREQ] ondemand: fix tickless accounting and software coordination bug
[CPUFREQ] ondemand: add a check to avoid negative load calculation
[CPUFREQ] Keep userspace governor quiet when it is not being used
[CPUFREQ] Longhaul - Proper register access
[CPUFREQ] Kconfig powernow-k8 driver should depend on ACPI P-States driver
[CPUFREQ] Longhaul - Replace ACPI functions with direct I/O
[CPUFREQ] Longhaul - Remove duplicate multipliers
[CPUFREQ] Longhaul - Embedded "conservative"
[CPUFREQ] acpi-cpufreq: Proper ReadModifyWrite of PERF_CTL MSR
[CPUFREQ] check return value of sysfs_create_file
[CPUFREQ] Longhaul - Check ACPI "BM DMA in progress" bit
[CPUFREQ] Longhaul - Move old_ratio to correct place
[CPUFREQ] Longhaul - VT8237 support
[CPUFREQ] Longhaul - Use all kinds of support
[CPUFREQ] powernow-k8: clarify number of cores.
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Support multiple CPUs going through OS_MCA
[IA64] silence GCC ia64 unused variable warnings
[IA64] prevent MCA when performing MMIO mmap to PCI config space
[IA64] add sn_register_pmi_handler oemcall
[IA64] Stop bit for brl instruction
[IA64] SN: Correct ROM resource length for BIOS copy
[IA64] Don't set psr.ic and psr.i simultaneously
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (61 commits)
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes
sysfs: make directory dentries and inodes reclaimable
sysfs: implement sysfs_get_dentry()
sysfs: move sysfs_drop_dentry() to dir.c and make it static
sysfs: restructure add/remove paths and fix inode update
sysfs: use sysfs_mutex to protect the sysfs_dirent tree
sysfs: consolidate sysfs spinlocks
sysfs: make kobj point to sysfs_dirent instead of dentry
sysfs: implement sysfs_find_dirent() and sysfs_get_dirent()
sysfs: implement SYSFS_FLAG_REMOVED flag
sysfs: rename sysfs_dirent->s_type to s_flags and make room for flags
sysfs: make sysfs_drop_dentry() access inodes using ilookup()
sysfs: Fix oops in sysfs_drop_dentry on x86_64
sysfs: use singly-linked list for sysfs_dirent tree
sysfs: slim down sysfs_dirent->s_active
sysfs: move s_active functions to fs/sysfs/dir.c
sysfs: fix root sysfs_dirent -> root dentry association
sysfs: use iget_locked() instead of new_inode()
sysfs: reorganize sysfs_new_indoe() and sysfs_create()
sysfs: fix parent refcounting during rename and move
...
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (21 commits)
libata: remove irq_on from ata_bus_reset() and ata_std_postreset()
ata_piix: kill incorrect invalid map value warning
libata: add another Maxtor drive with broken NCQ to the list
[libata] sata_mv: Fix and clean up per-chip-generation tests
[libata] sata_mv: Convert to new exception handling (EH) infrastructure
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
[libata] sata_mv: Minor cleanups and renaming, preparing for new EH & NCQ
libata-link: add PMP related ATA constants
libata-link: separate out ata_eh_handle_dev_fail()
pata_hpt3x3: fix DMA Kconfig option to actually have a hope of working
Add Hitachi HDS7250SASUN500G 0621KTAWSD to NCQ blacklist
pata_scc.c: Workaround for errata A308
libata: add FUJITSU MHV2080BH to NCQ blacklist
pata_hpt3x3: major reworking and testing
libata: clean up horkage handling
libata: quirk IOMEGA ZIP 250 ATAPI FLOPPY
libata: simplify PCI legacy SFF host handling
pata_mpc52xx: suspend/resume support
sata_promise: SATA hotplug support, take 2
pata_sis: FIFO whack
...
Russell King [Thu, 12 Jul 2007 20:29:45 +0000 (21:29 +0100)]
[ARM] sa1100: remove boot time RTC initialisation
The RTC library code contains everything necessary to set the
system time from the RTC; for similar reasons as the previous
commit, it's far better to let the RTC library code sort this
out rather than implement something which might not be
appropriate for everyone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 12 Jul 2007 20:29:06 +0000 (21:29 +0100)]
[ARM] sa1100: stop doing our own rtc management over suspend
Remove the RTC management over a suspend/resume cycle. As per the
corresponding PXA patch, the RTC library code handles updating
system time on resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Rename PC speaker code
[MIPS] Don't use genrtc.
[MIPS] Remove unused time.c for swarm
[MIPS] Sparse: Use NULL for pointer
[MIPS] Fix a sparse warning in arch/mips/pci/pci.c
[MIPS] SMTC: Interrupt mask backstop hack
[MIPS] separate platform_device registration for VR41xx RTC
[MIPS] Separate platform_device registration for VR41xx GPIO
[MIPS] MIPSsim: Fix build.
[MIPS] separate platform_device registration for VR41xx serial interface
[MIPS] Include cacheflush.h in uncache.c
[MIPS] Cleanup tlbdebug.h
[MIPS] Change names of local variables to silence sparse (part 2)
[MIPS] Workaround for a sparse warning in include/asm-mips/io.h
[MIPS] RM: Use only phyiscal address for 82596 and 53c710
[MIPS] Hydrogen3: Remove remaining bits of code.
[MIPS] DEC: Fix modpost warning.
Revert "[MIPS] DEC: Fix modpost warning."
[MIPS] Fix resume for 64K page size on R4000 class processors.
* master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin serial driver: supporting BF548-EZKIT serial port
Video Console: Blackfin doesnt support VGA console
Blackfin arch: Add peripheral io API to gpio header file
Blackfin arch: set up gpio interrupt IRQ_PJ9 for BF54x ATAPI PATA driver
Blackfin arch: add missing CONFIG_LARGE_ALLOCS when upstream merging
Blackfin arch: as pointed out by Robert P. J. Day, update the CPU_FREQ name to match current Kconfig
Blackfin arch: extract the entry point from the linked kernel
Blackfin arch: clean up some coding style issues
Blackfin arch: combine the common code of free_initrd_mem and free_initmem
Blackfin arch: Add Support for Peripheral PortMux and resouce allocation
Blackfin arch: use PAGE_SIZE when doing aligns rather than hardcoded values
Blackfin arch: fix bug set dma_address properly in dma_map_sg
Blackfin arch: Disable CACHELINE_ALIGNED_L1 for BF54x by default
Blackfin arch: Port the dm9000 driver to Blackfin by using the correct low-level io routines
Blackfin arch: There is no CDPRIO Bit in the EBIU_AMGCTL Register of BF54x arch
Blackfin arch: scrub dead code
Blackfin arch: Fix Warning add some defines in BF54x header file
Blackfin arch: add BF54x missing GPIO access functions
Blackfin arch: Some memory and code optimizations - Fix SYS_IRQS
Blackfin arch: Enable BF54x PIN/GPIO interrupts
...
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (26 commits)
i2c-rpx: Remove
i2c-mpc: work around missing-9th-clock-pulse bug
i2c: New PMC MSP71xx TWI bus driver
i2c-savage4: Delete many unused defines
i2c/tsl2550: Speed up initialization
i2c: New bus driver for the TAOS evaluation modules
i2c-i801: Use the internal 32-byte buffer on ICH4+
i2c-i801: Various cleanups
i2c: Add support for the TSL2550
i2c-pxa: Support new-style I2C drivers
i2c-gpio: Make some internal functions static
i2c-gpio: Add support for new-style clients
i2c-iop3xx: Switch to static adapter numbering
i2c-sis5595: Resolve resource conflict with sis5595
matroxfb: Clean-up i2c header inclusions
i2c-nforce2: Add support for SMBus block transactions
i2c-mpc: Use i2c_add_numbered_adapter
i2c-mv64xxx: Use i2c_add_numbered_adapter
i2c-piix4: Add support for the ATI SB700
i2c: New DS1682 chip driver
...
ata_piix: kill incorrect invalid map value warning
The last two slots of MAP 00b of ich6m was incorrectly marked as
reserved. This is left over from converting the entry to allow 00b.
This causes no real problem. It only makes the driver print annoying
warning message. Fix it.
[patch also proferred by Pierre Tardy at the end of 2006 -jg]
Jeff Garzik [Thu, 12 Jul 2007 19:51:22 +0000 (15:51 -0400)]
[libata] sata_mv: Fix and clean up per-chip-generation tests
Due to a mistake in test logic, Gen-IIE chips were being treated as
Gen-II chips in some cases. Fix this, and in the process, clean up
IS_50XX/IS_60XX tests to the more uniform IS_GEN_{I,II,IIE} tests.
Jeff Garzik [Thu, 12 Jul 2007 18:30:19 +0000 (14:30 -0400)]
[libata] sata_mv: minor bug fixes, enhancements, and cleanups (prep for new EH)
* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
not exist
* Set I/O Id field in descriptor, where present. Appears to work
fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
are always masked)
H. Peter Anvin [Wed, 11 Jul 2007 19:18:58 +0000 (12:18 -0700)]
Remove old i386 setup code
This removes the old i386 setup code. This is done as a separate patch
to avoid breaking git bisect as some of the i386 code was also used by
the old x86-64 code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:56 +0000 (12:18 -0700)]
Use the new x86 setup code for i386
This patch hooks the new x86 setup code into the Makefile machinery. It
also adapts boot/tools/build.c to a two-file (as opposed to three-file)
universe, and simplifies it substantially.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:53 +0000 (12:18 -0700)]
Code for actual protected-mode entry
This is the code which actually does the switch to protected mode,
including all preparation. It is also responsible for invoking the
boot loader hooks, if present.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:52 +0000 (12:18 -0700)]
Video mode probing support for the new x86 setup code
Video mode probing for the new x86 setup code. This code breaks down
different drivers into modules. This code deliberately drops support
for a lot of the vendor-specific mode probing present in the assembly
version, since a lot of those probes have been found to be stale in
current versions of those chips -- frequently, support for those modes
have been dropped from recent video BIOSes due to space constraints,
but the video BIOS signatures are still the same.
However, additional drivers should be extremely straightforward to plug
in, if desirable.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:35 +0000 (12:18 -0700)]
Make struct boot_params a real structure, and remove obsolete fields
Make struct boot_params a real structure, and remove the handling of
some obsolete fields, in particular hd*_info, which was only used by
the ST-506 driver, and likely to be wrong for that driver on any
modern BIOS.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:33 +0000 (12:18 -0700)]
Define zero-page offset 0x1e4 as a scratch field, and use it
The relocatable kernel code needs a scratch field for the decompressor
to determine its own location. It was using a location inside
struct screen_info; reserve a free location and document it as scratch
instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:31 +0000 (12:18 -0700)]
Clean up struct screen_info (<linux/screen_info.h>)
struct screen_info has unaligned members, it needs to be packed.
In the process, fix the naming of some of the members, which don't
belong in this structure but are part of it anyway.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:29 +0000 (12:18 -0700)]
Unify the CPU features vectors between i386 and x86-64
Unify the handling of the CPU features vectors between i386 and x86-64.
This also adopts the collapsing of features which are required at
compile-time into constant tests from x86-64 to i386.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Wed, 11 Jul 2007 19:18:27 +0000 (12:18 -0700)]
hd.c: remove BIOS/CMOS queries
An ST-506 disk these days is pretty much someone trying to pull ancient
data using an auxilliary controller. Pulling data from the BIOS or CMOS
is just plain wrong, since it's likely to be the primary OS disk... and
would be user-entered data anyway. Instead, require the user enters it
on the command line.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
The only pseudo-legitimate MIPS user of genrtc was a systems that doesn't
have an RTC in hardware at all. At this point faking one is a little
pointless ...
projects / linux-2.6-omap-h63xx.git / log