Kumar Gala [Mon, 22 Sep 2008 21:52:19 +0000 (14:52 -0700)]
netdev: drop CONFIG_PPC_MERGE from Kconfig
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ayaz Abdulla [Mon, 22 Sep 2008 13:55:35 +0000 (09:55 -0400)]
forcedeth fix: take phy out of reset during power up
This patch will add the phy reset bit into the power up mask which is
used during power up. Certain BIOSes will place the phy in reset and
therefore the driver must take the phy out of reset when it loads.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The second seems correct, but the first has a silly repetition of the
PCI device before the actual message. The message originates from
e1000_eeprom_checks in e1000e/netdev.c.
With this patch below the first message becomes
e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM
which makes it similar to directly preceding messages.
Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface
name has not yet been assigned at that point.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Frans Pop <elendil@planet.nl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jie Yang [Mon, 22 Sep 2008 21:52:25 +0000 (14:52 -0700)]
atl1e: remove the unneeded (struct atl1e_adapter *)
Remove the unneeded (struct atl1e_adapter *) casts, for hw->adapter
already has type atl1e_adapter *.
Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Andy Fleming <afleming@freescale.com> Reported-by: Daniel Marjamki <danielm77@spray.se> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Fries [Mon, 22 Sep 2008 21:10:20 +0000 (14:10 -0700)]
ne.c: fix rmmod, platform driver improvements
Removing the module would cause a kernel oops as platform_driver_probe
failed to detect a device and unregistered the platform driver on module
init, and cleanup_module would unregister the already unregistered driver.
The suspend and resume functions weren't being called.
platform_driver support was added earlier, but without any
platform_device_register* calls I don't think it was being used. Now all
devices are registered using platform_device_register_simple and pointers
are kept to unregister the ones that the probe failed for or unregister
all devices on module shutdown. init_module no longer calls ne_init to
reduce confusion (and multiple unregister paths that caused the rmmod
oops). With the devices now registered they are added to the platform
driver and get suspend and resume events.
netif_device_detach(dev) was added before unregister_netdev(dev) when
removing the region as occationally I would see a race condition where the
device was still being used in unregister_netdev.
Signed-off-by: David Fries <david@fries.net> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The loop with the timeout used "while (... && timeout--)", which means
than when the timeout occurs, "timeout" will be -1 after the loop has
exited. The code that checks if the looped exited because of a timeout
used "if (timeout <= 0)". Seems ok, except timeout is unsigned, and
(unsigned)-1 isn't less than zero!
Using "--timeout" in the loop fixes this problem, as now "timeout" will be
0 when the loop times out.
This also fixes a bug in the existing code, where it will erroneously think
a timeout occurred if the condition the loop was waiting for is satisfied
on the final iteration before a timeout.
Signed-off-by: Trent Piepho <tpiepho@freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Bruce Allan [Tue, 23 Sep 2008 22:46:38 +0000 (15:46 -0700)]
e1000e: remove failed request for sw/fw/hw flag
When the driver fails to acquire the control flag used to serialize
NVM and PHY accesses between the driver, firmware and hardware, remove the
request for the flag otherwise the hardware might grant the flag when it
becomes available but the driver will not release the flag. This could
cause the firmware to prevent the driver getting the flag for all future
attempts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Scott Feldman [Wed, 24 Sep 2008 18:23:53 +0000 (11:23 -0700)]
enic: bug fix: don't set netdev->name too early
Bug fix: don't set netdev->name early before netdev registration. Setting
netdev->name early with dev_alloc_name() would occasionally cause netdev
registration to fail returning error that device was already registered.
Since we're using netdev->name to name MSI-X vectors, we now need to
move the request_irq after netdev registartion, so move it to ->open.
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Scott Feldman [Wed, 24 Sep 2008 18:23:32 +0000 (11:23 -0700)]
enic: fixes for review items from Ben Hutchings
Fixes for review items from Ben Hutchings:
- use netdev->net_stats rather than private net_stats
- use ethtool op .get_sset_count rather than .get_stats_count
- err out if setting Tx/Rx csum or TSO using ethtool and setting is
not enabled for device.
- pass in jiffies + constant to round_jiffies
- return err if new MTU is out-of-bounds
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Scott Feldman [Wed, 24 Sep 2008 18:23:22 +0000 (11:23 -0700)]
enic: Don't indicate IPv6 pkts using soft-LRO
LRO is only applied to IPv4 pkts, so don't use the LRO indication functions
for anything other IPv4 pkts. Every non-IPv4 pkt is indicated using non-
LRO functions.
Signed-off-by: Scott Feldman <scofeldm@cisco.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Do not touch IFF_UP flag during qeth recovery, but invoke dev_close()
in case of failing recovery.
Cancel outstanding control commands in case of Data Checks or
Channel Checks.
Do not invoke qeth_l2_del_all_mc() in case of a hard stop to speed up
removal of qeth devices.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qeth: use firmware MAC-address for layer2 hsi-devices
Real HiperSocket devices in layer2 mode have a firmware-created
MAC-address. This change enables the qeth driver to use this
firmware MAC-address for layer2 HiperSocket devices.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dan Nicholson [Wed, 20 Aug 2008 23:51:59 +0000 (16:51 -0700)]
sundance: set carrier status on link change events
Check if the link is available when a changed interrupt has been received and
set the carrier status appropriately. The code is copied nearly verbatim from
the dl2k module. The link status could be used in more places in the driver,
but this is enough to get the carrier status reported to userspace. Fixes
kernel bug #7487:
http://bugzilla.kernel.org/show_bug.cgi?id=7487
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Dan Nicholson <dbn.lists@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Harvey Harrison [Wed, 20 Aug 2008 23:52:04 +0000 (16:52 -0700)]
drivers/net: replace __FUNCTION__ with __func__
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[netdrvr] usb/hso: throttle to prevent loss of serial data
Patch to stop loss of characters on the hso modems,
this patch throttles & unthrottles the modem by
not putting out urbs until the tty/line discipline layer
has enough space for newly received packets.
serial ports. This is required for firmware diagnostics
being done at Option.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Looks like to me that the ehea_fw_handles.lock mutex and the
ehea_bcmc_regs.lock spinlock are taken much longer than necessary and could
as well be pushed inside the functions that need them
(ehea_update_firmware_handles() and ehea_update_bcmc_registrations())
rather than at each callsite.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe can depend on dca IF it is enabled. So if we are compiled as
IXGBE=y, and DCA is enabled, then we must force INTEL_IOATDMA and therefore
DCA to be =y also.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 12 Sep 2008 03:05:39 +0000 (20:05 -0700)]
ixgbe: whitespace/formatting cleanup
This patch cleans up some whitespace items, reorders a couple of functions, and removes some outdated comments.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 12 Sep 2008 03:04:56 +0000 (20:04 -0700)]
ixgbe: correctly add and remove napi queues
This patch corrects support for NAPI so that queues are correctly added and
removed during suspend/resume in the event that the number of MSI-X vectors
changes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe: Whitespace, copyright update and version number change patch
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
in some configurations there can be more than one rx queue per vector
in msi-x mode. Add functionality to be able to clean this without
changing the performance path single-rx-queue cleanup.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
most of the time we only need 1500 bytes for a packet which means
we don't need a whole 4k page for each packet. Share the allocation
by using a reference count to the page and giving half to two
receive descriptors. This can enable us to use packet split mode
all the time due to the performance increase of allocating half
the pages.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
when using more than 8 tx queues you can overrun the 8 bit v_idx
field, so change it to 16 bits to represent the maximum number
of queues (one for each bit)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe was incorrectly setting the throttle rate setting for all tx
queues and the driver has been refreshed to better handle a dynamic
interrupt mode as well as multiple queues.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
1) reading some of the registers in our hardware causes them to clear,
so don't read ICR in the ethtool register dump function.
2) several register iterators were not iterating
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe: Update watchdog thread to accomodate longerlink_up events
This patch updates the link_up code and watchdog thread so that link_up
doesn't cause stack overflows due to long waits in interrupt context.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Wed, 3 Sep 2008 14:37:01 +0000 (15:37 +0100)]
sfc: Fix type of FALCON_SPI_MAX_LEN
FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int. This results in warnings from min() on 64-bit
architectures where they are different. Add a cast to make it match.
From: Steve Hodgson <shodgson@solarflare.com> Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:50:28 +0000 (12:50 +0100)]
sfc: Use CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS where appropriate
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ben Hutchings [Mon, 1 Sep 2008 11:49:37 +0000 (12:49 +0100)]
sfc: Make queue flushes more reliable
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
8139too: [cosmetic] fix incorrect register for flash-rom
I would like to submit a correction to the driver
drivers/net/8139too.c,
which in no way changes the compiled driver, but does change
the value of a previously incorrect value for the configuration
register address of Flash PROM on the network processor rtl8139C.
This corrected value is in accordance with the datasheet
for rtl8139C, and in addition this new value is indeed used
in other functional drivers that use this adapter for
programming a Flash memory chip in situ. But as said,
the two new constants are never referenced in the driver
maintained by you: they are only informational and correct!
s2io: Fix enabling VLAN tag stripping at driver initialization
VLAN doesn't work except if you'd opened the interface in promiscuous
mode before. This happens because VLAN tag stripping is not correctly
marked as enabled at device startup
Also, the vlan_strip_flag field was moved to the private network
structure.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Vlad Yasevich [Thu, 28 Aug 2008 19:38:41 +0000 (15:38 -0400)]
bonding: Do not tx-balance some IPv6 packets on ALB/TLB bonds
IPv6 all-node-multicasts and DAD probes should not be tx-balanced
on ALB/TLB bonds. The all-node-multicast is an equivalent to IPv4
broadcasts. DAD probes have to be sent only on the primary so that
we don't get false-positive detections.
Matthew Wilcox [Tue, 12 Aug 2008 13:13:14 +0000 (07:13 -0600)]
[netdrvr] atl1e: Don't take the mdio_lock in atl1e_probe
Lockdep warns about the mdio_lock taken with interrupts enabled then later
taken from interrupt context. Initially, I considered changing these
to spin_lock_irq/spin_unlock_irq, but then I looked at atl1e_phy_init()
and saw that it calls msleep(). Sleeping while holding a spinlock is
not allowed either.
In the probe path, we haven't registered the interrupt handler, so
it can't poke at this card yet. It's before we call register_netdev(),
so I don't think any other threads can reach this card either. If I'm
right, we don't need a spinlock at all.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
David Fries [Tue, 9 Sep 2008 03:01:14 +0000 (22:01 -0500)]
[netdrvr] ne: Fix suspend and resume for ISA PnP cards.
A call to pnp_stop_dev and pnp_start_dev now shuts down and
initializes plug and play devices for suspend and resume.
Signed-off-by: David Fries <david@fries.net> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Martin Gebert [Wed, 23 Jul 2008 07:40:09 +0000 (09:40 +0200)]
[netdrvr] au1000_eth: Spinlock initialisation fix
Seems like the spinlock for the AU1x00 ethernet device is initialised too
late, as it is already used in enable_mac(), which is called via
mii_probe() before the init takes place.
The attached patch is working here for a Linux Au1100 2.6.22.6 kernel,
and as far as I checked should also be applicable to the current head
(just line numbers differ).
Signed-off-by: Martin Gebert <Martin.Gebert@alpha-bit.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Chris Snook [Tue, 9 Sep 2008 07:26:57 +0000 (03:26 -0400)]
MAINTAINERS: add Atheros maintainer for atlx
Jie Yang at Atheros is getting more directly involved with upstream work on the
atl* drivers. This patch changes the ATL1 entry to ATLX (atl2 support posted
to netdev today) and adds him as a maintainer.
Andrew Morton [Fri, 5 Sep 2008 21:04:07 +0000 (14:04 -0700)]
drivers/net/mlx4/alloc.c needs mm.h
sparc32 allmodconfig with linux-next:
drivers/net/mlx4/alloc.c: In function 'mlx4_buf_alloc':
drivers/net/mlx4/alloc.c:164: error: 'PAGE_KERNEL' undeclared (first use in this function)
drivers/net/mlx4/alloc.c:164: error: (Each undeclared identifier is reported only once
drivers/net/mlx4/alloc.c:164: error: for each function it appears in.)
this is due to some header shuffle in linux-next. I didn't look to see what
it was. I'd sugges that this patch be merged ahead of a linux-next merge to
avoid bisection breaks.
We strictly only need asm/pgtable.h, but going direct to asm includes always
seems grubby.
Cc: Jeff Garzik <jeff@garzik.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Self-baked macros cause bunch of compile warnings like below:
CC [M] drivers/net/skfp/pmf.o
CC net/ipv4/fib_semantics.o
drivers/net/skfp/pmf.c:86: warning: cast from pointer to integer of different size
drivers/net/skfp/pmf.c:87: warning: cast from pointer to integer of different size
...
Use the standard offsetof() macro instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Acked-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Magnus Damm [Mon, 8 Sep 2008 05:02:56 +0000 (14:02 +0900)]
smc91x: fix nowait printout
Commit c4f0e76747e80578a8f7fddd82fd0ce8127bd2f8 added nowait platform
data support. The printout code was however not updated, so the value
of SMC_NOWAIT is still used. This patch makes sure that nowait is printed
accordingly to platform data.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- the register is defined for the 8169 chipset only and there is
no 8169 beyond RTL_GIGA_MAC_VER_06.
- only the lower 3 bytes of the register are valid
tulip: Fix dead 21041 ethernet after ifconfig down
The de2104x did a pci_disable_device() in it's close function, but
the open function never does a pci_enable_device() and assumes that
the device is already enabled. Considering that downing the interface
is just a temporary thing the pci_disable_device() isn't a pretty good
idea and removing it from the close function just fixes the bug.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Oliver Hartkopp [Wed, 24 Sep 2008 04:23:19 +0000 (21:23 -0700)]
net: remove ifalias on empty given alias
This patch removes the potentially allocated ifalias when the (new) given alias is empty.
E.g. when setting
echo "" > /sys/class/net/eth0/ifalias
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Sep 2008 03:47:22 +0000 (20:47 -0700)]
aoe: Fix OOPS after SKB queue changes.
Reported by Thomas Graf.
If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.
Add __skb_unlink() call to fix that.
Signed-off-by: David S. Miller <davem@davemloft.net>
pkt_sched: Remove the tx queue state check in qdisc_run()
The current check wrongly uses the state of one (currently the first)
tx queue for all tx queues in case of non-default qdiscs. This check
mainly prevented requeuing loop with __netif_schedule(), but now it's
controlled inside __qdisc_run(), while dequeuing. The wrongness of
this check was first noticed by Herbert Xu.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log