David Brownell [Fri, 10 Oct 2008 21:21:22 +0000 (14:21 -0700)]
new sharable twl4030 SIH irq_chip
Add TWL4030 infrastructure for shared SIH interrupts.
This is basically what the twl4030 GPIO IRQ code does, but
switching to a workqueue to handle each irqchip's mask/unmask
and set_type operations instead of a kthread that must figure
out what to do each time it wakes up.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 10 Oct 2008 21:20:46 +0000 (14:20 -0700)]
new twl4030 SIH irq init
Switch to a different twl4030-irq SIH irq init scheme. Its goal
is to remove some section issues while providing a data structure
that can be reused by generic SIH IRQ handling code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 10 Oct 2008 21:19:49 +0000 (14:19 -0700)]
create twl4030-irq.c
Split the IRQ support out of twl4030-core.c into twl4030-irq.c,
including some minor tidy-ups and a note_interrupt() paranoia
in case of flakiness with some PIH interrupt.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Fri, 10 Oct 2008 16:58:30 +0000 (10:58 -0600)]
i2c-omap: fix I2C timeouts due to recursive omap_i2c_{un,}idle()
omap_i2c_unidle() and omap_i2c_idle() are called recursively during
omap_i2c_probe(). This is evidently unexpected and will wipe
out the I2C interrupt enable register the second time that
omap_i2c_idle() is called consecutively. Any I2C transactions
following a probe of a bus with at least one device on it will then
time out.
Fix by moving omap_i2c_idle() further up in omap_i2c_probe(). Ensure
the I2C controller is marked as idle before the probe starts. Also
attempt to catch future reappearances of this bug early in development
by warning in omap_i2c_{un,}idle() when they are called recursively.
Problem reported by David Brownell <david-b@pacbell.net>.
Tested on 3430SDP and 2430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: David Brownell <david-b@pacbell.net> Cc: Richard Woodruff <r-woodruff2@ti.com>
Acked-by; Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Fri, 10 Oct 2008 12:18:58 +0000 (17:48 +0530)]
Enable CONFIG_GPIO_TWL4030=y
Without this option, kernel builds would fail, with
errors similar to:
hsmmc.c:50: undefined reference to `twl4030_get_gpio_datain'
hsmmc.c:82: undefined reference to `twl4030_free_gpio'
hsmmc.c:63: undefined reference to `twl4030_request_gpio'
hsmmc.c:67: undefined reference to `twl4030_set_gpio_debounce'
Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Wed, 8 Oct 2008 14:22:30 +0000 (17:22 +0300)]
twl4030-pwrirq simplification, cleanup
I can't test the pwrbutton stuff, but rtc and musb behave...
With one issue: the usb transceiver glue misbehaves on
startup if the device is connected. (Again.) I looked at
this a bit, and I think the issue is probably caused by
not actually using key USB registers ... IRQ trigger
mode state transitions are at best a fragile proxy for the
real state.
(This is similar to the GPIO patch I just sent, but simpler
except for the impact on the few drivers thinking oddly
about IRQs. Those patches cover the key SIH modules, and
a similar one affects the PIH in twl4030-core.)
- Dave
================================
Streamline the "power irq" code, and some of the mechanisms
it uses:
- Support IRQ masking, not just unmasking; simpler code.
- Use the standard handle_edge_irq() handler for these edge IRQs.
- Use generic_handle_irq() instead of a manual expansion thereof.
- Provide a missing spinlock for the shared data.
In short, use more of the standard genirq code ... more correctly.
Also, update the drivers using the "power IRQ" accordingly:
- Don't request IRQF_DISABLED if the handler makes I2C calls;
and defend against lockdep forcing it on us.
- Let the irq_chip handle IRQ mask/unmask; it handles mutual
exclusion between drivers, among other things.
- (Unrelated) remove useless MODULE_ALIAS in pwrbutton.
The USB transceiver driver still places some dodgey games with IRQ
enable/disable, and IRQ trigger flags. At least some of them seem
like they'd be simplified by using USB transceiver registers ...
notably, startup code, which doesn't seem to check state before
it enters an irq-driven mode.
For the moment, these drivers still (wrongly) try to configure IRQ
trigger modes themselves ... again, that's something that an irq_chip
handles (but not yet, for this one).
NOTE: tested (MUSB and RTC only) along with the init/retry hack
to make twl4030-pwrirq work around the i2c-omap timeout problems.
Previously, the only external (to dispc.c) IRQ handler was RFBI's
frame done handler. dispc's IRQ framework was very dumb: you could only
have one handler, and the semantics of {request,free}_irq were odd, to
say the least.
The new framework allows multiple consumers to register arbitrary IRQ
masks.
Signed-off-by: Daniel Stone <daniel.stone@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
FB: OMAP: Blizzard: Properly disable zoom when necessary
The problem is related to the following notice in the documentation:
"Once a destructive window with up-scaling is created, it can only be
disabled by creating a background window.". With the current omapfb
driver code, if you try to do a partial screen update (show menu or
dialog) after a scaled screen update (video overlay), scaling setting
are not reset properly and you see this "magnifying glass" effect if a
part of new update overlaps previously scaled area.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@nokia.com> Signed-off-by: Daniel Stone <daniel.stone@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Sanjeev Premi [Fri, 10 Oct 2008 10:19:51 +0000 (15:49 +0530)]
Fix compiler warnings in gpmc.c
Fix these compiler warnings:
gpmc.c: In function 'gpmc_init':
gpmc.c:432: warning: 'return' with a value, in function returning void
gpmc.c:439: warning: 'return' with a value, in function returning void
Signed-off-by: Sanjeev Premi <premi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Thu, 9 Oct 2008 23:22:22 +0000 (17:22 -0600)]
OMAP2xxx: move SRAM to fix boot hang
Commit 1c957036bbd912322793da676d05e169abf24782 breaks booting on
OMAP2; it causes the SRAM to be mapped on top of the L4 interconnect.
This causes the system to hang early in boot in omap_map_sram() during
the TLB flush. Fix by moving SRAM elsewhere in the memory map.
Reported by Jarkko Nikula <jarkko.nikula@nokia.com>. This patch is a
collaboration with Tony Lindgren <tony@atomide.com> and
Kevin Hilman <khilman@deeprootsystems.com>.
Boot-tested on 2430SDP (by Paul) and N810 (by Jarkko).
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Måns Rullgård <mans@mansr.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Thu, 9 Oct 2008 21:04:54 +0000 (14:04 -0700)]
Don't allow splice() to files opened with O_APPEND
This is debatable, but while we're debating it, let's disallow the
combination of splice and an O_APPEND destination.
It's not entirely clear what the semantics of O_APPEND should be, and
POSIX apparently expects pwrite() to ignore O_APPEND, for example. So
we could make up any semantics we want, including the old ones.
But Miklos convinced me that we should at least give it some thought,
and that accepting writes at arbitrary offsets is wrong at least for
IS_APPEND() files (which always have O_APPEND set, even if the reverse
isn't true: you can obviously have O_APPEND set on a regular file).
So disallow O_APPEND entirely for now. I doubt anybody cares, and this
way we have one less gray area to worry about.
Matt Mackall [Wed, 8 Oct 2008 19:51:57 +0000 (14:51 -0500)]
SLOB: fix bogus ksize calculation fix
This fixes the previous fix, which was completely wrong on closer
inspection. This version has been manually tested with a user-space
test harness and generates sane values. A nearly identical patch has
been boot-tested.
The problem arose from changing how kmalloc/kfree handled alignment
padding without updating ksize to match. This brings it in sync.
Signed-off-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hwmon: (abituguru3) Enable DMI probing feature on Abit AT8 32X
Enable driver checking of the DMI product name (when enabled) on
an Abit AT8 32X, instead of falling back to a manual probe. This
eliminates false negatives and eventually will help avoid
unnecessary bus probes on unsupported mainboards.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Daniel Exner <dex@dragonslave.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
hwmon: (abituguru3) Enable reading from AUX3 fan on Abit AT8 32X
The table for the Abit AT8 32X was incorrectly missing an entry
for the sixth ("AUX3") fan. Add this entry, exporting the fan
reading to userspace.
Closes lm-sensors.org ticket #2339.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk> Tested-by: Daniel Exner <dex@dragonslave.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Thu, 9 Oct 2008 13:33:58 +0000 (15:33 +0200)]
hwmon: (it87) Prevent power-off on Shuttle SN68PT
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Corentin Chary [Thu, 9 Oct 2008 13:33:57 +0000 (15:33 +0200)]
eeepc-laptop: Fix hwmon interface
Creates a name file in the sysfs directory, that
is needed for the libsensors library to work.
Also rename fan1_pwm to pwm1 and scale its value as needed.
This fixes bug #11520:
http://bugzilla.kernel.org/show_bug.cgi?id=11520
Signed-off-by: Corentin Chary <corentincj@iksaif.net> Signed-off-by: Jean Delvare <khali@linux-fr.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
net: Fix netdev_run_todo dead-lock
tcp: Fix possible double-ack w/ user dma
net: only invoke dev->change_rx_flags when device is UP
netrom: Fix sock_orphan() use in nr_release
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Revert "ax25: Fix std timer socket destroy handling."
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
tcp: Fix tcp_hybla zero congestion window growth with small rho and large cwnd.
Because of rounding, in certain conditions, i.e. when in congestion
avoidance state rho is smaller than 1/128 of the current cwnd, TCP
Hybla congestion control starves and the cwnd is kept constant
forever.
This patch forces an increment by one segment after #send_cwnd calls
without increments(newreno behavior).
Signed-off-by: Daniele Lacamera <root@danielinux.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 7 Oct 2008 22:50:03 +0000 (15:50 -0700)]
net: Fix netdev_run_todo dead-lock
Benjamin Thery tracked down a bug that explains many instances
of the error
unregister_netdevice: waiting for %s to become free. Usage count = %d
It turns out that netdev_run_todo can dead-lock with itself if
a second instance of it is run in a thread that will then free
a reference to the device waited on by the first instance.
The problem is really quite silly. We were trying to create
parallelism where none was required. As netdev_run_todo always
follows a RTNL section, and that todo tasks can only be added
with the RTNL held, by definition you should only need to wait
for the very ones that you've added and be done with it.
There is no need for a second mutex or spinlock.
This is exactly what the following patch does.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Ali Saidi [Tue, 7 Oct 2008 22:31:19 +0000 (15:31 -0700)]
tcp: Fix possible double-ack w/ user dma
From: Ali Saidi <saidi@engin.umich.edu>
When TCP receive copy offload is enabled it's possible that
tcp_rcv_established() will cause two acks to be sent for a single
packet. In the case that a tcp_dma_early_copy() is successful,
copied_early is set to true which causes tcp_cleanup_rbuf() to be
called early which can send an ack. Further along in
tcp_rcv_established(), __tcp_ack_snd_check() is called and will
schedule a delayed ACK. If no packets are processed before the delayed
ack timer expires the packet will be acked twice.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 7 Oct 2008 22:26:48 +0000 (15:26 -0700)]
net: only invoke dev->change_rx_flags when device is UP
Jesper Dangaard Brouer <hawk@comx.dk> reported a bug when setting a VLAN
device down that is in promiscous mode:
When the VLAN device is set down, the promiscous count on the real
device is decremented by one by vlan_dev_stop(). When removing the
promiscous flag from the VLAN device afterwards, the promiscous
count on the real device is decremented a second time by the
vlan_change_rx_flags() callback.
The root cause for this is that the ->change_rx_flags() callback is
invoked while the device is down. The synchronization is meant to mirror
the behaviour of the ->set_rx_mode callbacks, meaning the ->open function
is responsible for doing a full sync on open, the ->close() function is
responsible for doing full cleanup on ->stop() and ->change_rx_flags()
is meant to do incremental changes while the device is UP.
Only invoke ->change_rx_flags() while the device is UP to provide the
intended behaviour.
Tested-by: Jesper Dangaard Brouer <jdb@comx.dk> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Mackall [Tue, 7 Oct 2008 16:37:35 +0000 (11:37 -0500)]
SLOB: fix bogus ksize calculation
SLOB's ksize calculation was braindamaged and generally harmlessly
underreported the allocation size. But for very small buffers, it could
in fact overreport them, leading code depending on krealloc to overrun
the allocation and trample other data.
Signed-off-by: Matt Mackall <mpm@selenic.com> Tested-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Mon, 6 Oct 2008 07:41:32 +0000 (00:41 -0700)]
twl4030-gpio irq simplification
Simplify and correct TWL4030 GPIO IRQ handling:
- support mask() not just unmask()
- use genirq handle_edge_irq() handler not custom hacks
- let that handle (correct) accounting of chained IRQ counts
- use the more efficient clear-on-read mechanism
- don't misuse IRQ_LEVEL
- remove some superfluous locking
- locking fix: all irq_chip data needs spinlock protection
Cleanups:
- give the helper thread a more accurate name
- don't name the NOP ack() method misleadingly
- use generic_handle_irq(), not a manually unrolled version thereof
- comment fixes
Note that the previous IRQ dispatch code was somewhat confused.
It seemed not to know that it was working with edge triggered
interrupts, much less ones which could be transparently acked.
(Also note that COR=1 doesn't enable Clear-On-Read for all modules;
some are documented as using COR=0 for that. GPIO uses COR=1.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Tue, 7 Oct 2008 03:43:35 +0000 (20:43 -0700)]
twl4030-core irq simplification
Simplify twl4030 IRQ handling by removing a needless custom flow
handler. The top level IRQs, from the PIH, are well suited for
handle_simple_irq() ... they can't be acked or masked.
Switching resolves some issues with how IRQs were dispatched.
Notably, abuse of desc->status, IRQ accounting, and handling
of various faults.
In short, use standard genirq code.
Drivers that request_irq() to the PIH will need to pay more
attention to things like setting IRQF_DISABLED (since it's
no longer ignored), and making I2C calls from handlers (you'll
need a lockdep workaround).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Tue, 7 Oct 2008 03:37:59 +0000 (20:37 -0700)]
twl4030 "subdriver" irq tweaks
Bugfixes to TWL subdriver irq handler setup ... lockdep
workarounds, remove IRQF_DISABLED. NOPs with current code.
These changes are specific to the drivers which register
directly with the PIH irq_chip (in twl4030-core), and are
prerequsites to a cleanup patch for that PIH infrastructure.
(Unless you don't use these drivers.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Mon, 6 Oct 2008 20:17:35 +0000 (13:17 -0700)]
beagle: two more GPIOs
Request two more GPIOs on Beagle: MMC write protect, DVI enable.
Also define the first OMAP3 GPIO mux config symbols, with a new
naming convention. Examples:
- GPIO42 is bidirectional, and uses external pull up/down (if any);
- GPIO42_UP is bidirectional, with an internal pullup;
- GPIO42_DOWN is bidirectional, with an internal pulldown.
- GPIO42_OUT is output-only, and needs no pullup or pulldown.
All of those would be fully functional through the standard GPIO
interface as well as the legacy OMAP-only one, except GPIO42_OUT
which won't let you read the actual pin value after setting it.
There's no special off-mode support for these particular pins;
on Beagle they have external pullups or pulldowns.
(OMAP2 can use this naming convention too, except that since it
has no input-enable the "_OUT" convention can't be used there.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Theodore Ts'o (tytso@mit.edu) wrote:
>
> I've been playing with adding some markers into ext4 to see if they
> could be useful in solving some problems along with Systemtap. It
> appears, though, that as of 2.6.27-rc8, markers defined in code which is
> compiled directly into the kernel (i.e., not as modules) don't show up
> in Module.markers:
>
> kvm_trace_entryexit arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-intel %u %p %u %u %u %u %u %u
> kvm_trace_entryexit arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
> kvm_trace_handler arch/x86/kvm/kvm-amd %u %p %u %u %u %u %u %u
>
> (Note the lack of any of the kernel_sched_* markers, and the markers I
> added for ext4_* and jbd2_* are missing as wel.)
>
> Systemtap apparently depends on in-kernel trace_mark being recorded in
> Module.markers, and apparently it's been claimed that it used to be
> there. Is this a bug in systemtap, or in how Module.markers is getting
> built? And is there a file that contains the equivalent information
> for markers located in non-modules code?
Linus Torvalds [Mon, 6 Oct 2008 21:29:16 +0000 (14:29 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
Linus Torvalds [Mon, 6 Oct 2008 21:27:39 +0000 (14:27 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
Linus Torvalds [Mon, 6 Oct 2008 21:27:15 +0000 (14:27 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (33 commits)
V4L/DVB (9103): em28xx: HVR-900 B3C0 - fix audio clicking issue
V4L/DVB (9099): em28xx: Add detection for K-WORLD DVB-T 310U
V4L/DVB (9092): gspca: Bad init values for sonixj ov7660.
V4L/DVB (9080): gspca: Add a delay after writing to the sonixj sensors.
V4L/DVB (9075): gspca: Bad check of returned status in i2c_read() spca561.
V4L/DVB (9053): fix buffer overflow in uvc-video
V4L/DVB (9043): S5H1420: Fix size of shadow-array to avoid overflow
V4L/DVB (9037): Fix support for Hauppauge Nova-S SE
V4L/DVB (9029): Fix deadlock in demux code
V4L/DVB (8979): sms1xxx: Add new USB product ID for Hauppauge WinTV MiniStick
V4L/DVB (8978): sms1xxx: fix product name for Hauppauge WinTV MiniStick
V4L/DVB (8967): Use correct XC3028L firmware for AMD ATI TV Wonder 600
V4L/DVB (8963): s2255drv field count fix
V4L/DVB (8961): zr36067: Fix RGBR pixel format
V4L/DVB (8960): drivers/media/video/cafe_ccic.c needs mm.h
V4L/DVB (8958): zr36067: Return proper bytes-per-line value
V4L/DVB (8957): zr36067: Restore the default pixel format
V4L/DVB (8955): bttv: Prevent NULL pointer dereference in radio_open
V4L/DVB (8935): em28xx-cards: Remove duplicate entry (EM2800_BOARD_KWORLD_USB2800)
V4L/DVB (8933): gspca: Disable light frquency for zc3xx cs2102 Kokom.
...
atmel-mci: Initialize BLKR before sending data transfer command
The atmel-mci driver sometimes fails data transfers like this:
mmcblk0: error -5 transferring data
end_request: I/O error, dev mmcblk0, sector 2749769
end_request: I/O error, dev mmcblk0, sector 2749777
It turns out that this might be caused by the BLKR register (which
contains the block size and the number of blocks being transfered) being
initialized too late. This patch moves the initialization of BLKR so
that it contains the correct value before the block transfer command is
sent.
This error is difficult to reproduce, but if you insert a long delay
(mdelay(10) or thereabouts) between the calls to atmci_start_command()
and atmci_submit_data(), all transfers seem to fail without this patch,
while I haven't seen any failures with this patch.
Jarek Poplawski [Mon, 6 Oct 2008 19:54:57 +0000 (12:54 -0700)]
netrom: Fix sock_orphan() use in nr_release
While debugging another bug it was found that NetRom socks
are sometimes seen unorphaned in sk_free(). This patch moves
sock_orphan() in nr_release() to the beginning (like in ax25,
or rose).
Reported-and-tested-by: Bernard Pidoux f6bvp <f6bvp@free.fr> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Oct 2008 19:53:50 +0000 (12:53 -0700)]
ax25: Quick fix for making sure unaccepted sockets get destroyed.
Since we reverted 30902dc3cb0ea1cfc7ac2b17bcf478ff98420d74 ("ax25: Fix
std timer socket destroy handling.") we have to put some kind of fix
in to cure the issue whereby unaccepted connections do not get destroyed.
The approach used here is from Tihomir Heidelberg - 9a4gl
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wessel [Mon, 6 Oct 2008 18:50:59 +0000 (13:50 -0500)]
kgdb: call touch_softlockup_watchdog on resume
The softlockup watchdog needs to be touched when resuming the from the
kgdb stopped state to avoid the printk that a CPU is stuck if the
debugger was active for longer than the softlockup threshold.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Jan Kiszka [Mon, 6 Oct 2008 18:50:59 +0000 (13:50 -0500)]
kgdb, x86: Avoid invoking kgdb_nmicallback twice per NMI
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
x86 ACPI: Blacklist two HP machines with buggy BIOSes
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marcel Holtmann [Mon, 6 Oct 2008 10:22:52 +0000 (12:22 +0200)]
[Bluetooth] Add reset quirk for A-Link BlueUSB21 dongle
The new A-Link Bluetooth dongle is another one based on the BCM2046 chip
from Broadcom and it also needs to send HCI_Reset before it becomes fully
operational. Without the quirk it will show a lot of I/O errors.
Marcel Holtmann [Mon, 6 Oct 2008 10:22:51 +0000 (12:22 +0200)]
[Bluetooth] Add reset quirk for new Targus and Belkin dongles
Targus and Belkin have come out with new Bluetooth 2.1 capable dongles
using the latest BCM2046 chip from Broadcom. Both of them are so called
HID proxy dongles and they need to send HCI_Reset before they become
fully operational.
Marcel Holtmann [Mon, 6 Oct 2008 10:22:51 +0000 (12:22 +0200)]
[Bluetooth] Fix double frees on error paths of btusb and bpa10x drivers
The transfer buffer of an URB will be automatically freed when using
the URB_FREE_BUFFER transfer_flag. So the extra calls to kfree() will
cause a double free.
Felipe Balbi [Mon, 22 Sep 2008 15:10:26 +0000 (18:10 +0300)]
omap: ldp: fix compile breakage and physical/virtual address usage
commit bf9454a3aaf2cad2321aa8f97bfd5d8c4ebc7bf5 broke compilation
for ldp board. The following patch fixes it. Also fixes a wrong
cast from a void __iomem * to u32.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mans Rullgard [Thu, 2 Oct 2008 08:36:51 +0000 (09:36 +0100)]
OMAP: Increase VMALLOC_END to allow 256MB RAM
This increases VMALLOC_END to 0x18000000, making room for 256MB
RAM with the default 128MB vmalloc region.
Note that after this patch there's no longer a hole between vmalloc
space and the beginning of IO space on omap2 as the first virtual
mapping starts at 0xd8000000.
Signed-off-by: Mans Rullgard <mans@mansr.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
David Brownell [Fri, 3 Oct 2008 15:11:33 +0000 (08:11 -0700)]
bugfix: SOUND: SOC: OMAP: Add support for Gumstix Overo
Get rid of bogus ASOC boot messages on non-Overo boards,
such as with a kernel built for both Overo and Beagle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-By: Steve Sakoman <steve@sakoman.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 3 Oct 2008 16:04:12 +0000 (09:04 -0700)]
OMAP gpios implement new to_irq()
Make OMAP use the new __gpio_to_irq() hook, to make it easier to
support IRQs coming in from off-chip gpio controllers like the
TWL4030/TPS65930 chip used on OMAP3 boads like Beagleboard.org and
the Gumstix Overo.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 3 Oct 2008 16:02:55 +0000 (09:02 -0700)]
gpiolib to_irq() feature
Add a new gpiolib mechanism: gpio_chip instances can provide
mappings between their (input) GPIOs and any associated IRQs.
This makes it easier for platforms to support IRQs that are
provided by board-specific external chips instead of as part
of their core (such as SOC-integrated GPIOs).
Also update the irq_to_gpio() description, saying to avoid it
becuase it's not always supported.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 3 Oct 2008 16:00:48 +0000 (09:00 -0700)]
twl4030-core cleanup
A variety of twl4030-core cleanups:
- SIH register declarations moved from core.c to twl4030.h, for
keypad, madc, bci; this decouples from twl4030-madc.h; add
several omitted register decls; remove a duplicate.
- Use a global "inuse" flag, not a per-slave one;
- Remove pointless SLAVENUM_NUM symbols; just use 0/1/2/3
- Comments:
* Add comments: header, register values
* Add some section delimiters
* Correct clock init and other comments
- Minor stuff:
* Group some variables and code with sibling
* Make clock init a bit simpler
* List twl5030 in supported i2c chips list
* Remove needless "return;"
And one IRQ-related bugfix: if the I2C timeout bug strikes while
reading PIH interrupt status, force an immediate retry. Otherwise
the twl4030 IRQ will never get re-enabled...
Object size shrinks by 180 bytes, w00t!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 3 Oct 2008 16:00:10 +0000 (09:00 -0700)]
remove <linux/i2c/twl4030-pwrirq.h>
Get rid of another needless TWL header file: twl4030-pwrirq.h
can easily live in twl4030.h; updating its three users.
Also switch to the shared definition of the SIH_CTRL COR bit,
remove useless-to-non-driver MODULE_ALIAS(), and add a note
about a bug that will appear if anyone ever removes this code.
No functional changes, just shrinkage.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
David Brownell [Fri, 3 Oct 2008 15:59:32 +0000 (08:59 -0700)]
remove <linux/i2c/twl4030-rtc.h>
Remove <linux/i2c/twl4030-rtc.h> by moving all the relevant contents
into the driver itself, and removing the rest. Stuff removed included
many useless bitmasks, and remnants of the platform data hook.
Add markers inside the rtc driver to split sections apart: first
data structure declarations, then the RTC driver, then platform bus
glue for it all.
There's still an issue with the twl4030-pwrirq.h registers ... this
driver has no business touching them! This patch at least switches
away from having private versions of those register definitions, and
removes some unnecessary accesses to them.
No functional changes, just shrinkage.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ralf Baechle [Sun, 5 Oct 2008 16:23:28 +0000 (18:23 +0200)]
IDE: Fix platform device registration in Swarm IDE driver (v2)
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Sun, 5 Oct 2008 16:23:27 +0000 (18:23 +0200)]
ide-cd: temporary tray close fix
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com> Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
projects / linux-2.6-omap-h63xx.git / log