Choraria, Rohit [Fri, 11 Jan 2008 06:07:03 +0000 (11:37 +0530)]
OMAP3: FLASH: Move Flash specific device info in aseparate board file
This patch does the following
moves flash specific code to a new file board-3430sdp-flash.c
adds support for 3430 ES2 SDP changes for ethernet
changes the check in gpmc to OMAP34XX as same address is valid. Signed-off-by: Rohit Choraria <rohitkc@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Fri, 28 Dec 2007 20:38:23 +0000 (16:38 -0400)]
MMC: OMAP: Do not busy wait for end of command for ever
The limit was a fixed 100k limit in the busy loop, which is not
accurate. It would better to have time limit for the worst case
which occurs when sending 80 cycles at 400 kHz and takes about
200 microseconds, so limit the max time spend in the busy loop
for some 250 microseconds.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Fri, 28 Dec 2007 20:38:20 +0000 (16:38 -0400)]
MMC: OMAP: Start new commands from work queue instead of irq
Use work queues for starting new commands instead of starting them
directly from irq handler. The command scheduling needs to be delayed
a bit for some cards which should not be done from an interrupt.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Fri, 28 Dec 2007 20:38:17 +0000 (16:38 -0400)]
MMC: OMAP: Lazy clock shutdown
MMCA spec says the mmc clock should be kept running for at least
8 cycles after the last RW request. Ensure this with lazy clock
disable after a request, or with an explicit delay before
switching a slot.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Jarkko Lavinen [Fri, 28 Dec 2007 20:38:09 +0000 (16:38 -0400)]
MMC: OMAP: Use tasklet instead of workqueue for cover switch notification
The cover waitqueue is occasionally scheduled twice from timer
and the interrupt and oops follows. It would have been possible
to fix this problem with spinlocks but using tasklet was a dropin
sloution with no need for locking.
This path also adds some cleanups.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com> Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Tue, 22 Jan 2008 03:40:05 +0000 (19:40 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
tc35815: Use irq number for tc35815-mac platform device id
[MIPS] Malta: Fix reading the PCI clock frequency on big-endian
[MIPS] SMTC: Fix build error.
Andrew G. Morgan [Tue, 22 Jan 2008 01:18:30 +0000 (17:18 -0800)]
Fix filesystem capability support
In linux-2.6.24-rc1, security/commoncap.c:cap_inh_is_capped() was
introduced. It has the exact reverse of its intended behavior. This
led to an unintended privilege esculation involving a process'
inheritable capability set.
To be exposed to this bug, you need to have Filesystem Capabilities
enabled and in use. That is:
- CONFIG_SECURITY_FILE_CAPABILITIES must be defined for the buggy code
to be compiled in.
- You also need to have files on your system marked with fI bits raised.
Signed-off-by: Andrew G. Morgan <morgan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Stefan Schmidt [Tue, 22 Jan 2008 01:18:27 +0000 (17:18 -0800)]
s3c2410_fb: fix line length calculation
Fix line length calculation. var->width is the size of the display in mm. We
like to use the pixel size.
Without this fix, dynamic (fbset) based resolution and depths changes with
s3c2410_fb don't work at all.
Spotted by john cass <johnpcass@yahoo.com>
Signed-off-by: Stefan Schmidt <stefan@openmoko.org> Signed-off-by: Harald Welte <laforge@openmoko.org> Acked-by: Ben Dooks <ben-linux@fluff.org> Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Randy Dunlap [Tue, 22 Jan 2008 01:18:25 +0000 (17:18 -0800)]
timer: fix section mismatch
The caller is __cpuinit.
Also, this code block and its caller are inside #ifdef CONFIG_HOTPLUG_CPU
blocks, so this code should reflect that config symbol's usage.
WARNING: vmlinux.o(.text+0x4252f): Section mismatch: reference to .init.text: (between 'timer_cpu_notify' and 'msleep')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Alan Cox [Tue, 22 Jan 2008 01:18:24 +0000 (17:18 -0800)]
keyspan: fix oops
If we get a data URB back from the hardware after we have put the tty to
bed we go kaboom. Fortunately all we need to do is process the URB without
trying to ram its contents down the throat of an ex-tty.
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@akpm@linux-foundation.org>
Atsushi Nemoto [Fri, 18 Jan 2008 16:15:52 +0000 (01:15 +0900)]
tc35815: Use irq number for tc35815-mac platform device id
The tc35815-mac platform device used a pci bus number and a devfn to
identify its target device, but the pci bus number may vary if some
bus-bridges are found. Use irq number which is be unique for embedded
controllers.
Dmitri Vorobiev [Mon, 14 Jan 2008 21:27:46 +0000 (00:27 +0300)]
[MIPS] Malta: Fix reading the PCI clock frequency on big-endian
The JMPRS register on Malta boards keeps a 32-bit CPU-endian
value. The readw() function assumes that the value it reads is a
little-endian 16-bit number. Therefore, using readw() to obtain
the value of the JMPRS register is a mistake. This error leads
to incorrect reading of the PCI clock frequency on big-endian
during board start-up.
Change readw() to __raw_readl().
This was tested by injecting a call to printk() and verifying
that the value of the jmpr variable was consistent with current
setting of the JP4 "PCI CLK" jumper.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In that patch, David L added a icmp_out_count() in
ip_push_pending_frames(), remove icmp_out_count() from
icmp_reply(). But he forgot to remove icmp_out_count() from
icmp_send() too. Since icmp_send and icmp_reply will call
icmp_push_reply, which will call ip_push_pending_frames, a duplicated
increment happened in icmp_send.
This patch remove the icmp_out_count from icmp_send too.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Mon, 21 Jan 2008 11:05:43 +0000 (03:05 -0800)]
[IPV6]: RFC 2011 compatibility broken
The snmp6 entry name was changed, and it broke compatibility
to RFC 2011.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Mon, 21 Jan 2008 11:04:47 +0000 (03:04 -0800)]
[IPV6]: ICMP6_MIB_OUTMSGS increment duplicated
icmpv6_send() calls ip6_push_pending_frames() indirectly.
Both ip6_push_pending_frames() and icmpv6_send() increment
counter ICMP6_MIB_OUTMSGS.
This patch remove the increment from icmpv6_send.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Mon, 21 Jan 2008 01:25:14 +0000 (17:25 -0800)]
[NET]: rtnl_link: fix use-after-free
When unregistering the rtnl_link_ops, all existing devices using
the ops are destroyed. With nested devices this may lead to a
use-after-free despite the use of for_each_netdev_safe() in case
the upper device is next in the device list and is destroyed
by the NETDEV_UNREGISTER notifier.
The easy fix is to restart scanning the device list after removing
a device. Alternatively we could add new devices to the front of
the list to avoid having dependant devices follow the device they
depend on. A third option would be to only restart scanning if
dev->iflink of the next device matches dev->ifindex of the current
one. For now this seems like the safest solution.
With this patch, the veth rtnl_link_ops unregistration can use
rtnl_link_unregister() directly since it now also handles destruction
of multiple devices at once.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Juhl [Mon, 21 Jan 2008 00:58:04 +0000 (16:58 -0800)]
[IrDA]: af_irda memory leak fixes
Here goes an IrDA patch against your latest net-2.6 tree.
This patch fixes some af_irda memory leaks. It also checks for
irias_new_obect() return value.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 21 Jan 2008 00:39:03 +0000 (16:39 -0800)]
[NEIGH]: Revert 'Fix race between neigh_parms_release and neightbl_fill_parms'
Commit 9cd40029423701c376391da59d2c6469672b4bed (Fix race between
neigh_parms_release and neightbl_fill_parms) introduced device
reference counting regressions for several people, see:
http://bugzilla.kernel.org/show_bug.cgi?id=9778
for example.
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets are flood-forwarded to multiple output devices, the
bridge-netfilter code reuses skb->nf_bridge for each clone to store
the bridge port. When queueing packets using NFQUEUE netfilter takes
a reference to skb->nf_bridge->physoutdev, which is overwritten
when the packet is forwarded to the second port. This causes
refcount unterflows for the first device and refcount leaks for all
others. Additionally this provides incorrect data to the iptables
physdev match.
Unshare skb->nf_bridge by copying it if it is shared before assigning
the physoutdev device.
Reported, tested and based on initial patch by
Jan Christoph Nordholz <hesso@pool.math.tu-berlin.de>.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] ROUTE: Make sending algorithm more friendly with RFC 4861.
We omit (or delay) sending NSes for known-to-unreachable routers (in
NUD_FAILED state) according to RFC 4191 (Default Router Preferences
and More-Specific Routes). But this is not fully compatible with RFC
4861 (Neighbor Discovery Protocol for IPv6), which does not remember
unreachability of neighbors.
So, let's avoid mixing sending algorithm of RFC 4191 and that of RFC
4861, and make the algorithm more friendly with RFC 4861 if RFC 4191
is disabled.
Issue was found by IPv6 Ready Logo Core Self_Test 1.5.0b2 (by TAHI
Project), and has been tracked down by Mitsuru Chinen
<mitch@linux.vnet.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 18 Jan 2008 12:30:21 +0000 (04:30 -0800)]
[IPV4] FIB_HASH : Avoid unecessary loop in fn_hash_dump_zone()
I noticed "ip route list" was slower than "cat /proc/net/route" on a
machine with a full Internet routing table (214392 entries : Special
thanks to Robert ;) )
David S. Miller [Fri, 18 Jan 2008 12:21:39 +0000 (04:21 -0800)]
[NET]: Fix interrupt semaphore corruption in Intel drivers.
Several of the Intel ethernet drivers keep an atomic counter used to
manage when to actually hit the hardware with a disable or an enable.
The way the net_rx_work() breakout logic works during a pending
napi_disable() is that it simply unschedules the poll even if it
still has work.
This can potentially leave interrupts disabled, but that is OK
because all of the drivers are about to disable interrupts
anyways in all such code paths that do a napi_disable().
Unfortunately, this trips up the semaphore used here in the Intel
drivers. If you hit this case, when you try to bring the interface
back up it won't enable interrupts. A reload of the driver module
fixes it of course.
So what we do is make sure all the sequences now go:
Russell King [Sun, 20 Jan 2008 10:18:12 +0000 (10:18 +0000)]
Merge branch 'omap-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
ARM: OMAP1: Fix compile for board-nokia770
ARM: OMAP1: Keymap fix for f-sample and p2-sample
Dan Williams [Fri, 18 Jan 2008 22:26:10 +0000 (23:26 +0100)]
[ARM] 4748/1: dca: source drivers/dca/Kconfig in arch/arm/Kconfig to fix warning
'select' used by config symbol 'INTEL_IOATDMA' refers to undefined symbol 'DCA'
Although drivers/dma is currently the only user future drivers outside of
drivers/dma may select this option so it is better to add this to
arch/arm/Kconfig than move DCA to drivers/dma/Kconfig.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Fri, 11 Jan 2008 12:23:58 +0000 (12:23 +0000)]
[ARM] pxa: don't rely on r2 being preserved over a function call
r2 is not guaranteed to be preserved over a function call, so relying
on it to store the link register over the call to sleep_phys_sp() is
unreliable. Store the link register on the stack instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rusty Russell [Sun, 20 Jan 2008 00:54:18 +0000 (11:54 +1100)]
Remove bogus duplicate CONFIG_LGUEST_GUEST entry.
It was moved to arch/x86/lguest/Kconfig, but I lost the deletion part in a
patch suffle. My confused one-liner "fix" to turn it on is also reverted: 84f7466ee20cc094aa38617abfa2f3834871f054
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Sat, 19 Jan 2008 15:51:26 +0000 (15:51 +0000)]
pata_pdc202xx_old: Fix crashes with ATAPI
The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)
So turn it ATAPI DMA off, these are disk optimised controllers.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Klaus Pedersen [Fri, 18 Jan 2008 17:30:23 +0000 (19:30 +0200)]
T2: Remove redundant clear and restore of the COR flag
The T2 Clear-On-Read (COR) feature works by clearing all pending
irqs when the ISR register is read. It should be needless to say
that this feature isn't compatible with shared interrupts, unless
the value of the ISR is read only once for each interrupt.
It is therefor safe to assume that COR is not used - because if a
driver uses the feature, that driver will clear the interrupts
belonging to other drivers.
This patch removes the redundant clearing and restoring of the COR
bit in REG_PWR_SIH_CTRL.
Signed-off-by: Klaus Pedersen <klaus.k.pedersen@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] clarify watchdog operation in documentation
[WATCHDOG] Revert "Stop looking for device as soon as one is found"
Arjan van de Ven [Fri, 18 Jan 2008 21:49:33 +0000 (22:49 +0100)]
x86: add support for the latest Intel processors to Oprofile
The latest Intel processors (the 45nm ones) have a model number of 23
(old ones had 15); they're otherwise compatible on the oprofile side.
This patch adds the new model number to the oprofile code.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro [Sun, 13 Jan 2008 14:17:35 +0000 (14:17 +0000)]
3c574, 3c515 bitfields abuse
wn3_config is shared by these cards; the way we deal with it is both bad C
(union abuse) and broken on big-endian. For 3c515 it's less serious (ISA
cards are quite rare outside of little-endian boxen), but 3c574 is a pcmcia
one and that'd better be endian-independent... Fix is the same in both
cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Garzik <jeff@garzik.org>
S2io: Fixed synchronization between scheduling of napi with card reset and close
- Fixed synchronization between scheduling of napi with card reset and close
by moving the enabling and disabling of napi to card up and card down
functions respectively instead of open and close.
Jay Cliburn [Tue, 15 Jan 2008 01:56:41 +0000 (19:56 -0600)]
atl1: fix frame length bug
The driver sets up the hardware to accept a frame with max length
equal to MTU + Ethernet header + FCS + VLAN tag, but we neglect to
add the VLAN tag size to the ingress buffer. When a VLAN-tagged
frame arrives, the hardware passes it, but bad things happen
because the buffer is too small. This patch fixes that.
Thanks to David Harris for reporting the bug and testing the fix.
Tested-by: David Harris <david.harris@cpni-inc.com> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some BIOS's break if Wake On Lan is enabled, and the machine
can't boot. Better to have some user's have to call ethtool to
enable WOL than to break a single user's boot.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:02 +0000 (16:25 -0800)]
bonding: fix lock ordering for rtnl and bonding_rwsem
Fix the handling of rtnl and the bonding_rwsem to always be acquired
in a consistent order (rtnl, then bonding_rwsem).
The existing code sometimes acquired them in this order, and sometimes
in the opposite order, which opens a window for deadlock between ifenslave
and sysfs.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:01 +0000 (16:25 -0800)]
bonding: Fix up parameter parsing
A recent change to add an additional hash policy modified
bond_parse_parm, but it now does not correctly match parameters passed in
via sysfs.
Rewrote bond_parse_parm to handle (a) parameter matches that
are substrings of one another and (b) user input with whitespace (e.g.,
sysfs input often has a trailing newline).
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:25:00 +0000 (16:25 -0800)]
bonding: release slaves when master removed via sysfs
Add a call to bond_release_all in the bonding netdev event
handler for the master. This releases the slaves for the case of, e.g.,
"echo -bond0 > /sys/class/net/bonding_masters", which otherwise will spin
forever waiting for references to be released.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:59 +0000 (16:24 -0800)]
bonding: fix locking during alb failover and slave removal
alb_fasten_mac_swap (actually rlb_teach_disabled_mac_on_primary)
requries RTNL and no other locks. This could cause dev_set_promiscuity
and/or dev_set_mac_address to be called with improper locking.
Changed callers to hold only RTNL during calls to alb_fasten_mac_swap
or functions calling it. Updated header comments in affected functions to
reflect proper reality of locking requirements.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:58 +0000 (16:24 -0800)]
bonding: fix ASSERT_RTNL that produces spurious warnings
Move an ASSERT_RTNL down to where we should hold only RTNL;
the existing check produces spurious warnings because we hold additional
locks at _bh, tripping a debug warning in spin_lock_mutex().
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Fri, 18 Jan 2008 00:24:57 +0000 (16:24 -0800)]
bonding: fix locking in sysfs primary/active selection
Fix the functions that store the primary and active slave
options via sysfs to hold the correct locks in the correct order.
The bond_change_active_slave and bond_select_active_slave
functions both require rtnl, bond->lock for read and curr_slave_lock for
write_bh, and no other locks. This is so that the lower level
mode-specific functions (notably for balance-alb mode) can release locks
down to just rtnl in order to call, e.g., dev_set_mac_address with the
locks it expects (rtnl only).
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Paul Walmsley [Fri, 18 Jan 2008 06:21:46 +0000 (23:21 -0700)]
sram: remove SCM read from plat-omap/sram.c
This patch removes the System Control Module read from
plat-omap/sram.c:is_sram_locked(). Instead, it uses the global system_reg
variable, which is initialized immediately prior to the SRAM init code.
This happens to fix the compile breakage on the current tree.
In the long term, is_sram_locked() probably should be moved out of
sram.c.
Boot-tested on N800.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[NIU]: Fix 1G PHY link state handling.
[NET]: Fix TX timeout regression in Intel drivers.
Nigel Cunningham [Thu, 17 Jan 2008 23:21:21 +0000 (15:21 -0800)]
Fix unbalanced helper_lock in kernel/kmod.c
call_usermodehelper_exec() has an exit path that can leave the
helper_lock() call at the top of the routine unbalanced. The attached
patch fixes this issue.
projects / linux-2.6-omap-h63xx.git / log