[ARM] pxa/zylonite: add support for USB OHCI

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] ohci-pxa27x: use ioremap() and offset for register access

This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()

Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource

Depending on the order of how resource is defined in the platform
device is not good, use platform_get_{irq,resource} for the IRQ
and memory resources.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers

Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: simplify DMA register definitions

1. DRCMRxx is no longer recommended, use DRCMR(xx) instead, and
   pass DRCMR index by "struct resource" if possible

2. DCSRxx, DDADRxx, DSADRxx, DTADRxx, DCMDxx is never used, use
   DCSR(), DDADR(), DSADR(), DTADR(), DCMD() instead

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: make additional DCSR bits valid for PXA3xx

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: fix incorrect initialization of mfp sysdev when not pxa2xx

The initialization of mfp sysdev in pxa2xx_mfp_init() shall really be
avoided when !cpu_is_pxa2xx().

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branches 'pxa-core' and 'pxa-machines' into pxa-all

Conflicts:

arch/arm/mach-pxa/Kconfig
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c

Merge branch 'for_rmk' of git://git.mnementh.co.uk/linux-2.6-im

Merge branch 'pxa-eseries' into pxa-machines

Conflicts:

arch/arm/mach-pxa/Makefile

Merge branch 'viper-for-rmk' of git://www.misterjones.org/linux-2.6-arm

Merge branch 'pxa-viper' into pxa-machines

Conflicts:

arch/arm/mach-pxa/Makefile
drivers/pcmcia/Kconfig
drivers/pcmcia/Makefile

Merge branch 'pxa-palm' into pxa-machines

Conflicts:

drivers/mfd/Kconfig
drivers/pcmcia/Makefile

Merge branch 'pxa-trizeps' into pxa-machines

Conflicts:

drivers/pcmcia/Makefile

Merge branches 'metronomefb', 'pxa-cm2xx', 'pxa-gumstix', 'pxa-misc', 'pxa-mitac', 'pxa-mp900', 'pxa-zylonite' and 'pxa-zaurus' into pxa-machines

Conflicts:

arch/arm/mach-pxa/poodle.c

[ARM] pxa: trizeps4: remove unused variable

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5285/1: pxa: update xm_x2xx_defconfig

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5284/1: pxa: cm-x255: add NOR and NAND flash support

This patch adds support for NOR and NAND flashes on CM-X255.
The NAND flash support uses not yet merged GPIO NAND driver.

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5283/1: pxa: add CM-X255 pcmcia support

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5282/1: pxa: add CM-X255 support

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5281/1: pxa: split cm-x2xx.c to cm-x2xx.c and cm-x270.c

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5280/1: pxa: prepare cm-x2xx.c and cm-x2xx-pci.[ch] for addition of CM-X255

- Change CM-X255 and CM-X270 common function prefix from cmx270 to cmx2xx
- Split cmx2xx_init to common and CM-X270-specific parts
- Use dynamic assignement for DM9000 resources and led GPIOs.

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5286/2: pxa: rename cm-x270* to cm-x2xx* to allow addition of cm-x255 support

Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5294/1: Trizeps4 PCMCIA support

Support for Trizeps4 SOM PCMCIA
with ConXS or other baseboards.
with double GPIO-free fixed (sorry!)

replaces 5279/1

Signed-off-by: Jurgen Schindele <linux@schindele.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5278/1: i2c-pxa fast mode support

Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 4733/1: export sharpsl_param

EXPORT sharpsl_param which is necessary to support modular build of some depending drivers.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5277/1: Add basic support for MobilePro 900/c

This patch adds basic support for the Mobilepro
900/c mini-laptop. At present it won't do much
more than build and boot.

Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5248/1: wm97xx generic battery driver

This patch adds generic battery driver for wm97xx chips.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5251/1: remove old LED support for Trizeps4 SOM

Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...

Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5204/1: Trizeps4 SOM update

- use MFP-API for GPIO
- support TRIZEPS4WL module
- cleanups

Signed-off-by: Jrgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: make "gpio_leds" static

Magician's "gpio_leds" was global, but actually is supposed to be
private.  Make it so.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/pcm027: convert to use new MFP API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/lpd270: use new .lcd_conn to specify LCD info

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/lpd270: convert to use new MFP API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/idp: remove the unnecessary idp_init_irq()

TOUCH_PANEL_IRQ is never referenced, and set_irq_type() shouldn't
be called in this way, remove it, as well as the idp_init_irq(),
and use pxa25x_init_irq() instead.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Cliff Brake <cliff.brake@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/idp: make use of "lcd_conn", add LCD pin configurations

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Cliff Brake <cliff.brake@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/idp: convert to use new MFP API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Cliff Brake <cliff.brake@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/colibri: convert to use new MFP API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/lubbock: add missing MFP pin configurations

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: better MFP low power state support for pxa25x/pxa27x

When configured as a specific low power state: MFP_LPM_DRIVE_LOW,
MFP_LPM_DRIVE_HIGH, the corresponding GPDR register bit during
low power mode shall be re-configured as output (if they are not
configured so), thus the PGSRx bits can output.

Create an additional low power values GPDR registers, and properly
save/restore the GAFR + GPDR registers when doing suspend/resume.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: fix typo in pxa25x MFP definitions

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 5238/2: Very basic Palm Zire 72 support

This patch contains very basic support of Palm Zire 72.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: remove references to pxa_gpio_mode() in comments

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: avoid needless pxa_gpio_mode() during resume

The pin configurations are restored early on during resume.  There's
no need for drivers to re-affirm the gpio modes.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: introduce cpu_is_pxa26x()

PXA26x (PXA261/262) is actually a PXA250 with stacked Intel(R)
StartaFlash. And this can be decided by bit 3 (PKG_TYPE) of
BOOT_DEF register.

Due to this extra I/O register access, make cpu_is_pxa26x() a
public function instead of a macro.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: make cpu_is_pxa2* macros more consistent

1. add a CPUID table in the comment

2. make cpu_is_pxa25x() true for PXA210/250/255/26x

3. PXA210 is treated as PXA25x, all related code modified to
   reflect this

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: merge common cpu_is_pxa255() code together

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Documentation: fix the now deprecated reference to {set,reset}_scoop_gpio

Due to recent patches removing the now deprecated references to
{set,reset}_scoop_gpio() and converting them to the generic GPIO
API, the references in the documentation also need to be fixed.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] corgi_lcd: use GPIO API for BACKLIGHT_ON and BACKLIGHT_CONT

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/akita: use pca953x instead of akita-ioexp

Use generic pca953x which provides gpiolib interface instead of
akita-specific akita-ioexp with non-standard interface to pins.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: use leds-gpio for led driving and drop leds-spitz

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-spitz

Drop leds-spitz.c and the declarations of now un-referenced
spitzscoop_device, spitzscoop2_device.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: use generic GPIO API for SCOOP1/SCOOP2 GPIOs

Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: use leds-gpio for led driving and drop leds-corgi

Now as the scoop pins are covered by the generic gpio API,
we can use leds-gpio driver instead of special leds-corgi

Drop leds-corgi.c and remove the declaration of now un-referenced
corgiscoop_device.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: use generic GPIO API for SCOOP GPIOs

Original patch from Dmitry Baryshkov's inital scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: prepare scoop for the generic GPIO API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/littleton: add support for SPI-based TDO24M LCD panel driver

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c

Now poodle/corgi/spitz have been been converted to use SPI-based
drivers, remove the now unused corgi_ssp.c and corgi_lcd.c. And
as well as the unused reference of {corgi,spitz}ssp_device.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: use SPI-based driver for ads7846, corgi-lcd and max1111

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: use new .lcd_conn to specify the LCD info

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: convert to use new MFP API

Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.

TODO: figure out the MFP configuration of the SSP2 which looks like
to be already configured by the boot loader, though.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/spitz: convert to use new GPIO API

Original patch from Dmitry Baryshkov's initial scoop gpio conversion
work at http://git.infradead.org/users/dbaryshkov/zaurus-2.6.git.

Separated into this dedicated generic GPIO conversion patch for the
work of deprecating pxa_gpio_mode().

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: use SPI-based driver for ads7846, corgi-lcd and max1111

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: convert to use new MFP API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/corgi: convert to use new GPIO API

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: use SPI based ads7846 touch screen driver

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: convert to use the new MFP API to configure pins

The MFP configuration table is reverse engineered from those
magic GAFRx_{L|U} values, and it looks much better now.

Also, the deprecated pxa_gpio_mode() invocations are removed.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: convert to use the new GPIO API

Direct manipulation of GPIO registers are no longer encouraged, use
the new GPIO API instead. Since the GPIO has to be requested before
use, .startup and .shutdown are added to the IrDA device platform
data to request and free the GPIO.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: use new .lcd_conn to specify the LCD info

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: use .gpio_pullup in USB device platform data

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa/poodle: move scoop/locomo device registration earlier

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

hwmon: add max1111_read_channel() for use by sharpsl_pm

This is not generic, and is added here for backward compatibility.
It is made an individual commit here to make it easier for revert
once the sharpsl_pm gets generic enough.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

hwmon: add max1111 Low-power Multichannel Serial 8-bit ADCs

Driver based on corgi_ssp.c and sharpsl_pm.c, previously done by Richard
Purdie and many others.

Now changed to generic HWMON device and expose all the ADC input value
through sysfs.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

lcd: add support for Toppoly TDO24M series LCD panels

This type of LCD panel can be found on PXA3xx/Littleton platforms.
Add LCD device and SPI-based driver for this.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

lcd: add corgibl_limit_intensity() to corgi_lcd

This is not generic enough, added here for backward compatibility.
And make this an individual commit so future revert will be a bit
easier.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

lcd: add SPI-based LCD and backlight driver for SHARP corgi/spitz

The driver is based on different source files including corgi_ssp.c,
corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie
and many others.

The LCD and Backlight device actually share the same SPI device, so
they are made into this single driver.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

lcd: allow lcd device to handle mode change events

Some LCD panels are capable of different resolutions, and is allowed
to change at run-time, so to make "struct lcd_device" to be able to
handle mode change events here.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Input: ads7846 - introduce .gpio_pendown to get pendown state

The GPIO connected to ADS7846 nPENIRQ signal is usually used to get
the pendown state as well. Introduce a .gpio_pendown, and use this
to decide the pendown state if .get_pendown_state is NULL.

Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Linux 2.6.27-rc6

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv6: Fix OOPS in ip6_dst_lookup_tail().
  ipsec: Restore larval states and socket policies in dump
  [Bluetooth] Reject L2CAP connections on an insecure ACL link
  [Bluetooth] Enforce correct authentication requirements
  [Bluetooth] Fix reference counting during ACL config stage

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Disable timer interrupts in fixup_irqs().

ipv6: Fix OOPS in ip6_dst_lookup_tail().

This fixes kernel bugzilla 11469: "TUN with 1024 neighbours:
ip6_dst_lookup_tail NULL crash"

dst->neighbour is not necessarily hooked up at this point
in the processing path, so blindly dereferencing it is
the wrong thing to do.  This NULL check exists in other
similar paths and this case was just an oversight.

Also fix the completely wrong and confusing indentation
here while we're at it.

Based upon a patch by Evgeniy Polyakov.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevents: remove WARN_ON which was used to gather information

clockevents: remove WARN_ON which was used to gather information

The issue of the endless reprogramming loop due to a too small
min_delta_ns was fixed with the previous updates of the clock events
code, but we had no information about the spread of this problem. I
added a WARN_ON to get automated information via kerneloops.org and to
get some direct reports, which allowed me to analyse the affected
machines.

The WARN_ON has served its purpose and would be annoying for a release
kernel. Remove it and just keep the information about the increase of
the min_delta_ns value.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: fix memmap=exactmap boot argument
  x86: disable static NOPLs on 32 bits
  xen: fix 2.6.27-rc5 xen balloon driver warnings

x86: fix memmap=exactmap boot argument

When using kdump modifying the e820 map is yielding strange results.

For example starting with

 BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000100 - 0000000000093400 (usable)
 BIOS-e820: 0000000000093400 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
 BIOS-e820: 000000003fee0000 - 000000003fef3000 (ACPI data)
 BIOS-e820: 000000003fef3000 - 000000003ff80000 (ACPI NVS)
 BIOS-e820: 000000003ff80000 - 0000000040000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)

and booting with args

memmap=exactmap memmap=640K@0K memmap=5228K@16384K memmap=125188K@22252K memmap=76K#1047424K memmap=564K#1047500K

resulted in:

 user-defined physical RAM map:
 user: 0000000000000000 - 0000000000093400 (usable)
 user: 0000000000093400 - 00000000000a0000 (reserved)
 user: 0000000000100000 - 000000003fee0000 (usable)
 user: 000000003fee0000 - 000000003fef3000 (ACPI data)
 user: 000000003fef3000 - 000000003ff80000 (ACPI NVS)
 user: 000000003ff80000 - 0000000040000000 (reserved)
 user: 00000000e0000000 - 00000000f0000000 (reserved)
 user: 00000000fec00000 - 00000000fec10000 (reserved)
 user: 00000000fee00000 - 00000000fee01000 (reserved)
 user: 00000000ff000000 - 0000000100000000 (reserved)

But should have resulted in:

 user-defined physical RAM map:
 user: 0000000000000000 - 00000000000a0000 (usable)
 user: 0000000001000000 - 000000000151b000 (usable)
 user: 00000000015bb000 - 0000000008ffc000 (usable)
 user: 000000003fee0000 - 000000003ff80000 (ACPI data)

This is happening because of an improper usage of strcmp() in the
e820 parsing code.  The strcmp() always returns !0 and never resets the
value for e820.nr_map and returns an incorrect user-defined map.

This patch fixes the problem.

Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] cio: allow offline processing for disconnected devices
  [S390] cio: handle ssch() return codes correctly.
  [S390] cio: Correct cleanup on error.
  [S390] CVE-2008-1514: prevent ptrace padding area read/write in 31-bit mode

Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] IP22: Fix detection of second HPC3 on Challenge S

Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6

* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6:
  UBIFS: make minimum fanout 3
  UBIFS: fix division by zero
  UBIFS: amend f_fsid
  UBIFS: fill f_fsid
  UBIFS: improve statfs reporting even more
  UBIFS: introduce LEB overhead
  UBIFS: add forgotten gc_idx_lebs component
  UBIFS: fix assertion
  UBIFS: improve statfs reporting
  UBIFS: remove incorrect index space check
  UBIFS: push empty flash hack down
  UBIFS: do not update min_idx_lebs in stafs
  UBIFS: allow for racing between GC and TNC
  UBIFS: always read hashed-key nodes under TNC mutex
  UBIFS: fix zero-length truncations

lib: Correct printk %pF to work on all architectures

It was introduced by "vsprintf: add support for '%pS' and '%pF' pointer
formats" in commit 0fe1ef24f7bd0020f29ffe287dfdb9ead33ca0b2.  However,
the current way its coded doesn't work on parisc64.  For two reasons: 1)
parisc isn't in the #ifdef and 2) parisc has a different format for
function descriptors

Make dereference_function_descriptor() more accommodating by allowing
architecture overrides.  I put the three overrides (for parisc64, ppc64
and ia64) in arch/kernel/module.c because that's where the kernel
internal linker which knows how to deal with function descriptors sits.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: add Atheros maintainer for atlx

Jie Yang at Atheros is getting more directly involved with upstream work
on the atl* drivers.  This patch changes the ATL1 entry to ATLX (atl2
support posted to netdev today) and adds him as a maintainer.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

update Documentation/filesystems/Locking for 2.6.27 changes

In the 2.6.27 circle ->fasync lost the BKL, and the last remaining
->open variant that takes the BKL is also gone.  ->get_sb and ->kill_sb
didn't have BKL forever, so updated the entries while we're at that.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add default configuration for Arcom/Eurotech Viper SBC

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

Add support for the Arcom/Eurotech Viper SBC CompactFlash card slot

The Arcom/Eurotech Viper needs some extra care to run. On this board,
the PC104 connector is actually wired to the second PCMCIA slot.
Therefore, this second socket needs to be enabled, despite not being
managed by the PCMCIA code.

I'd rather have the MECR setup in the platform support code so I could,
for example, use the PC104 bus without having the PCMCIA module loaded.

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

Add support for the Arcom/Eurotech Viper SBC onboard ethernet.

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

Basic support for the Arcom/Eurotech Viper SBC.

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

Export smc91x led definitions

Now that we can configure smc91x leds from its platform data,
it seems rather useful to move the led definitions to the
externally visible header file.

Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>

[ARM] 5244/1: Add hardware CTSRTS flow control to pxa serial driver

Adds hardware CTSRTS control for pxa serial devices through
termios controls.

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] pxa: Allow platforms to override PSPR setting

Currently, we set PSPR just before entering sleep mode.  However,
some platforms have different requirements for setting PSPR in
order to properly wake up.

Set PSPR earlier in the suspend cycle so that platforms can
change the setting by using a sysdev driver instead.

Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>