Arjan van de Ven [Wed, 15 Oct 2008 09:52:34 +0000 (10:52 +0100)]
tty: make sure that proc_clear_tty stores the cpu flags
proc_clear_tty() gets called with interrupts off (while holding the task list
lock) from sys_setid. This means that it needs the _irqsave version of the
locking primitives.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com> Tested-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we skip unrecognized options in xfs_fs_remount we should just break
out of the switch and not return because otherwise we may skip clearing
the xfs-internal read-only flag. This will only show up on some
operations like touch because most read-only checks are done by the VFS
which thinks this filesystem is r/w. Eventually we should replace the
XFS read-only flag with a helper that always checks the VFS flag to make
sure they can never get out of sync.
Bug reported and fix verified by Marcel Beister on #xfs.
Bug fix verified by updated xfstests/189.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Timothy Shimmin <tes@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 15 Oct 2008 15:07:35 +0000 (08:07 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (158 commits)
powerpc: Fix CHRP PCI config access for indirect_pci
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
powerpc: Fix 32-bit SMP boot on CHRP
powerpc: Fix link errors on 32-bit machines using legacy DMA
powerpc/pci: Improve detection of unassigned bridge resources
hvc_console: Fix free_irq in spinlocked section
powerpc: Get USE_STRICT_MM_TYPECHECKS working again
powerpc: Reflect the used arguments in machine_init() prototype
powerpc: Fix DMA offset for non-coherent DMA
powerpc: fix fsl_upm nand driver modular build
powerpc/83xx: add NAND support for the MPC8360E-RDK boards
powerpc: FPGA support for GE Fanuc SBC610
i2c: MPC8349E-mITX Power Management and GPIO expander driver
powerpc: reserve two DMA channels for audio in MPC8610 HPCD device tree
powerpc: document the "fsl,ssi-dma-channel" compatible property
powerpc: disable CHRP and PMAC support in various defconfigs
OF: add fsl,mcu-mpc8349emitx to the exception list
powerpc/83xx: add DS1374 RTC support for the MPC837xE-MDS boards
powerpc: remove support for bootmem-allocated memory for the DIU driver
powerpc: remove non-dependent load fsl_booke PTE_64BIT
...
Linus Torvalds [Tue, 14 Oct 2008 23:53:02 +0000 (16:53 -0700)]
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-viapro: Add support for SMBus Process Call transactions
i2c: Restore i2c_smbus_process_call function
i2c: Do earlier driver model init
i2c: Only build Tyan SMBus mux drivers on x86
i2c: Guard against oopses from bad init sequences
i2c: Document the implementation details of the /dev interface
i2c: Improve dev-interface documentation
i2c-parport-light: Don't register a platform device resource
hwmon: (dme1737) Convert to a new-style i2c driver
hwmon: (dme1737) Be less i2c-centric
i2c/tps65010: Vibrator hookup to gpiolib
i2c-viapro: Add VX800/VX820 support
i2c: Renesas Highlander FPGA SMBus support
i2c-pca-isa: Don't grab arbitrary resources
i2c/isp1301_omap: Convert to a new-style i2c driver, part 2
i2c/isp1301_omap: Convert to a new-style i2c driver, part 1
Linus Torvalds [Tue, 14 Oct 2008 23:35:43 +0000 (16:35 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: build drivers for all quirky devices by default
HID: add missing blacklist entry for Apple ATV ircontrol
HID: add support for Bright ABNT2 brazilian device
HID: Don't let Avermedia Radio FM800 be handled by usb hid drivers
HID: fix numlock led on Dell device 0x413c/0x2105
HID: remove warn() macro from usb hid drivers
HID: remove info() macro from usb HID drivers
HID: add appletv IR receiver quirk
HID: fix a lockup regression when using force feedback on a PID device
HID: hiddev.h: Fix example code.
HID: hiddev.h: Fix mixed space and tabs in example code.
HID: convert to dev_* prints
HID: remove hid-ff
HID: move zeroplus FF processing
HID: move thrustmaster FF processing
HID: move pantherlord FF processing
HID: fix incorrent length condition in hidraw_write()
HID: fix tty<->hid deadlock
HID: ignore iBuddy devices
HID: report descriptor fix for remaining MacBook JIS keyboards
...
Linus Torvalds [Tue, 14 Oct 2008 23:34:11 +0000 (16:34 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
ocfs2: Make cached block reads the common case.
ocfs2: Kill the last naked wait_on_buffer() for cached reads.
ocfs2: Move ocfs2_bread() into dir.c
ocfs2: Simplify ocfs2_read_block()
ocfs2: Require an inode for ocfs2_read_block(s)().
ocfs2: Separate out sync reads from ocfs2_read_blocks()
ocfs2: Refactor xattr list and remove ocfs2_xattr_handler().
ocfs2: Calculate EA hash only by its suffix.
ocfs2: Move trusted and user attribute support into xattr.c
ocfs2: Uninline ocfs2_xattr_name_hash()
ocfs2: Don't check for NULL before brelse()
ocfs2: use smaller counters in ocfs2_remove_xattr_clusters_from_cache
ocfs2: Documentation update for user_xattr / nouser_xattr mount options
ocfs2: make la_debug_mutex static
ocfs2: Remove pointless !!
ocfs2: Add empty bucket support in xattr.
ocfs2/xattr.c: Fix a bug when inserting xattr.
ocfs2: Add xattr mount option in ocfs2_show_options()
ocfs2: Switch over to JBD2.
ocfs2: Add the 'inode64' mount option.
...
Bjorn Helgaas [Tue, 14 Oct 2008 23:01:59 +0000 (17:01 -0600)]
rtc-cmos: look for PNP RTC first, then for platform RTC
We shouldn't rely on "pnp_platform_devices" to tell us whether there
is a PNP RTC device.
I introduced "pnp_platform_devices", but I think it was a mistake.
All it tells us is whether we found any PNPBIOS or PNPACPI devices.
Many machines have some PNP devices, but do not describe the RTC
via PNP. On those machines, we need to do the platform driver probe
to find the RTC.
We should just register the PNP driver and see whether it claims anything.
If we don't find a PNP RTC, fall back to the platform driver probe.
This (in conjunction with the arch/x86/kernel/rtc.c patch to add
a platform RTC device when PNP doesn't have one) should resolve
these issues:
powerpc: Fix CHRP PCI config access for indirect_pci
Recently, indirect_pci was changed to test if the bus number requested
is the one hanging straight off the PHB, then it substitutes the bus
number with another one contained in a new "self_busno" field of the
pci_controller structure.
However, this breaks CHRP which didn't initialize this new field, and
which relies on having the right bus number passed to the hardware.
This fixes it by initializing this variable properly for all CHRP bridges
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/chrp: Fix detection of Python PCI host bridge on IBM CHRPs
The detection of the IBM "Python" PCI host bridge on IBM CHRP
machines such as old RS6000 was broken when we changed
of_device_is_compatible() from strncasecmp to strcasecmp (dropped
the "n" variant) due to the way IBM encodes the chip version.
We fix that by instead doing a match on the model property like
we do for others bridges in that file. It should be good enough
for those machines. If yours is still broken, let me know.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: Fix link errors on 32-bit machines using legacy DMA
The new merged DMA code will try to access isa_bridge_pcidev when
trying to DMA to/from legacy devices. This is however only defined
on 64-bit. Fixes this for now by adding the variable, even if it
stays NULL. In the long run, we'll make isa-bridge.c common to
32 and 64-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pci: Improve detection of unassigned bridge resources
When the powerpc PCI layer is not configured to re-assign everything,
it currently fails to detect that a PCI to PCI bridge has been left
unassigned by the firmware and tries to allocate resource for the
default window values in the bridge (0...X) (with the notable exception
of a hack we have in there that detects some Apple firmware unassigned
bridge resources).
This results in resource allocation failures, which are generally
fixed up later on but it causes scary warnings in the logs and we
have seen the fixup code fall over in some circumstances (a different
issue to fix as well).
This code improves that by providing a more complete & useful function
to intuit that a bridge was left unassigned by the firmware, and thus
force a full re-allocation by the PCI code without trying to allocate
the existing useless resources first.
The algorithm we use basically considers unassigned a window that
starts at 0 (PCI address) if the corresponding address space enable
bit is not set. In addition, for memory space, it considers such a
resource unassigned also if the host bridge isn't configured to
forward cycles to address 0 (ie, the resource basically overlaps
main memory).
This fixes a range of problems with things like Bare-Metal support
on pSeries machines, or attempt to use partial firmware PCI setup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit 611e097d7707741a336a0677d9d69bec40f29f3d
Author: Christian Borntraeger <borntraeger@de.ibm.com>
hvc_console: rework setup to replace irq functions with callbacks
introduced a spinlock recursion problem. The notifier_del is
called with a lock held, and in turns calls free_irq which then
complains when manipulating procfs. This fixes it by moving the
call to the notifier to outside of the locked section.
Signed-off-by: Christian Borntraeger<borntraeger@de.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jiri Kosina [Tue, 14 Oct 2008 21:37:33 +0000 (23:37 +0200)]
HID: build drivers for all quirky devices by default
Once kernel configuration has CONFIG_HID turned on, let also all the
specialized drivers for quirky devices to be built (unless CONFIG_EMBEDDED is
specified), as usually users don't care that much which driver
gives them the functionality, but when they want generic support, they
probably want to have support for all the quirky devices as well.
USB should not be having it's own printk macros, so remove warn() and
use the system-wide standard of dev_warn() wherever possible. In the
few places that will not work out, use a basic printk().
Anssi Hannula [Sat, 4 Oct 2008 12:44:06 +0000 (14:44 +0200)]
HID: fix a lockup regression when using force feedback on a PID device
Commit 8006479c9b75fb6594a7b746af3d7f1fbb68f18f introduced a spinlock in
input_dev->event_lock, which is locked when handling input events.
However, the hid-pidff driver sleeps when handling events as it waits for
reports being sent to the device before changing the report contents
again.
This causes a system lockup when trying to use force feedback with a PID
device, a regression introduced in 2.6.24 and 2.6.23.15.
Fix it by extracting the raw report data from struct hid_report
immediately when hid_submit_report() is called, therefore allowing
drivers to change the contents of struct hid_report immediately without
affecting the already-queued transfer.
In hid-pidff, re-add the removed usbhid_wait_io() to
pidff_erase_effect() instead, to prevent a full report queue from causing
the submission to fail, thus not freeing up device memory.
pidff_erase_effect() is not called while dev->event_lock is held.
hid_compat_load() runs on the default workqueue, it request_module(), it
execs modprobe, it exits, tty flushes default workqueue, it hangs, because
we are still in it.
HID: report descriptor fix for remaining MacBook JIS keyboards
This patch fixes a problem that MacBook JIS keyboard sends wrong report
descriptors. Although it has already been fixed in the first Core 2 Duo model,
it still remains in other models of MacBook.
HID: Autocentering support for Logitech MOMO Racing Wheel
Current kernel has no support for autocentering for Logitech wheels. By
default autocentering enabled in wheel and constant effect does not work
properly. Using USB sniffer I found command which change autocentering
settings: 0xFE, 0x0D, 0x0R, 0x0L, 0x80, 0x00, 0x00, where R - clockwise force,
L - counter-clockwise (0x0-0xF, 0xC = 100%).
Richard Hughes [Wed, 27 Aug 2008 09:19:37 +0000 (11:19 +0200)]
HID: remove ignore quirk for MGE UPS devices
This patch reverts the change made four years ago here:
http://www.vg.kernel.org/pub/linux/kernel/people/gregkh/usb/2.4/usb-hid-2.4.25-pre7.patch
UPS's made by MGE can be used with usbhid just fine, and by removing the
ignore quirk allows them to be used with HAL so they just work when plugged
in, without needing to be manually configured.
With the ignore quirk in place a user would have to configure NUT before the
UPS could be used, as NUT uses it's own internal USB matching framework
to match against the USB devices, do low level control messages on the
device and then parse the HID tables all in userspace.
This is not needed, as allowing the device to be claimed as a usbhid device
allows it to be used like any other USB UPS device. The devices correctly
advertise the power device page which can be queried for the device state.
I assume the quirk was changed so that people using < libusb 0.1.8 could
still use NUT's internal HID code to manage the UPS.
libusb 0.1.8 was released quite some time ago: 2004-02-11.
This patch does not break NUT as in drivers/libusb.c the device is force
unbound from the kernel driver using usb_detach_kernel_driver_np () where
it can be controlled like normal.
[jkosina@suse.cz: adapt to the new hidbus code]
Signed-off-by: Richard Hughes <rhughes@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jiri Kosina [Wed, 20 Aug 2008 17:13:52 +0000 (19:13 +0200)]
HID: introduce list for hiddev creation forcing
Introduce a list of devices for which there is need to
force a creation of the hiddev interface, but still they
are operated by generic driver (i.e. certain UPS).
Jiri Slaby [Fri, 16 May 2008 09:49:20 +0000 (11:49 +0200)]
HID: move ignore quirks
Move ignore quirks from usbhid-quirks into hid-core code. Also don't output
warning when ENODEV is error code in usbhid and try ordinal input in hidp
when that error is returned.
Jiri Slaby [Fri, 16 May 2008 09:49:16 +0000 (11:49 +0200)]
HID: hid, make parsing event driven
Next step for complete hid bus, this patch includes:
- call parser either from probe or from hid-core if there is no probe.
- add ll_driver structure and centralize some stuff there (open, close...)
- split and merge usb_hid_configure and hid_probe into several functions
to allow hooks/fixes between them
Jiri Slaby [Fri, 16 May 2008 09:49:15 +0000 (11:49 +0200)]
HID: make a bus from hid code
Make a bus from hid core. This is the first step for converting all the
quirks and separate almost-drivers into real drivers attached to this bus.
It's implemented to change behaviour in very tiny manner, so that no driver
needs to be changed this time.
Also add generic drivers for both usb and bt into usbhid or hidp
respectively which will bind all non-blacklisted device. Those blacklisted
will be either grabbed by special drivers or by nobody if they are broken at
the very rude base.
Linus Torvalds [Tue, 14 Oct 2008 19:31:14 +0000 (12:31 -0700)]
Merge branch 'for-2.6.28' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.28' of git://linux-nfs.org/~bfields/linux: (59 commits)
svcrdma: Fix IRD/ORD polarity
svcrdma: Update svc_rdma_send_error to use DMA LKEY
svcrdma: Modify the RPC reply path to use FRMR when available
svcrdma: Modify the RPC recv path to use FRMR when available
svcrdma: Add support to svc_rdma_send to handle chained WR
svcrdma: Modify post recv path to use local dma key
svcrdma: Add a service to register a Fast Reg MR with the device
svcrdma: Query device for Fast Reg support during connection setup
svcrdma: Add FRMR get/put services
NLM: Remove unused argument from svc_addsock() function
NLM: Remove "proto" argument from lockd_up()
NLM: Always start both UDP and TCP listeners
lockd: Remove unused fields in the nlm_reboot structure
lockd: Add helper to sanity check incoming NOTIFY requests
lockd: change nlmclnt_grant() to take a "struct sockaddr *"
lockd: Adjust nlmsvc_lookup_host() to accomodate AF_INET6 addresses
lockd: Adjust nlmclnt_lookup_host() signature to accomodate non-AF_INET
lockd: Support non-AF_INET addresses in nlm_lookup_host()
NLM: Convert nlm_lookup_host() to use a single argument
svcrdma: Add Fast Reg MR Data Types
...
Linus Torvalds [Tue, 14 Oct 2008 19:28:02 +0000 (12:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-fastboot
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arjan/linux-2.6-fastboot:
raid, fastboot: hide RAID autodetect option if MD is compiled as a module
raid: make RAID autodetect default a KConfig option
warning: fix init do_mounts_md c
fastboot: make the RAID autostart code print a message just before waiting
fastboot: make the raid autodetect code wait for all devices to init
fastboot: Fix bootgraph.pl initcall name regexp
fastboot: fix issues and improve output of bootgraph.pl
Add a script to visualize the kernel boot process / time
- afa9b649 "fbcon: prevent cursor disappearance after switching to 512
character font"
- d850a2fa "vt/fbcon: fix background color on line feed"
- 7fe3915a "vt/fbcon: update scrl_erase_char after 256/512-glyph font
switch"
by request of Alan Cox. Quoth Alan:
"Unfortunately it's wrong and its been causing breakages because
various apps like ncurses expect our previous (and correct)
behaviour."
Alexander sent out a similar patch.
Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Tested-by: Jan Engelhardt <jengelh@medozas.de> Cc: Alexander V. Lukyanov <lav@netis.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joel Becker [Fri, 10 Oct 2008 00:20:34 +0000 (17:20 -0700)]
ocfs2: Make cached block reads the common case.
ocfs2_read_blocks() currently requires the CACHED flag for cached I/O.
However, that's the common case. Let's flip it around and provide an
IGNORE_CACHE flag for the special users. This has the added benefit of
cleaning up the code some (ignore_cache takes on its special meaning
earlier in the loop).
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 10 Oct 2008 00:20:33 +0000 (17:20 -0700)]
ocfs2: Kill the last naked wait_on_buffer() for cached reads.
ocfs2's cached buffer I/O goes through ocfs2_read_block(s)(). dir.c had
a naked wait_on_buffer() to wait for some readahead, but it should
use ocfs2_read_block() instead.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 10 Oct 2008 00:20:31 +0000 (17:20 -0700)]
ocfs2: Simplify ocfs2_read_block()
More than 30 callers of ocfs2_read_block() pass exactly OCFS2_BH_CACHED.
Only six pass a different flag set. Rather than have every caller care,
let's make ocfs2_read_block() take no flags and always do a cached read.
The remaining six places can call ocfs2_read_blocks() directly.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 10 Oct 2008 00:20:30 +0000 (17:20 -0700)]
ocfs2: Require an inode for ocfs2_read_block(s)().
Now that synchronous readers are using ocfs2_read_blocks_sync(), all
callers of ocfs2_read_blocks() are passing an inode. Use it
unconditionally. Since it's there, we don't need to pass the
ocfs2_super either.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 10 Oct 2008 00:20:29 +0000 (17:20 -0700)]
ocfs2: Separate out sync reads from ocfs2_read_blocks()
The ocfs2_read_blocks() function currently handles sync reads, cached,
reads, and sometimes cached reads. We're going to add some
functionality to it, so first we should simplify it. The uncached,
synchronous reads are much easer to handle as a separate function, so we
instroduce ocfs2_read_blocks_sync().
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Julia Lawall [Mon, 13 Oct 2008 19:59:04 +0000 (21:59 +0200)]
arch/m68k/mm/kmap.c: introduce missing kfree
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
..
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
..>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
| arch/m68k/kernel/ints.c:433: error: redefinition of 'init_irq_proc'
| include/linux/interrupt.h:438: error: previous definition of 'init_irq_proc' was here
This was introduced by commit 6168a702ab0be181e5e57a0b2d0e7376f7a47f0b
("Declare init_irq_proc before we use it."), which replaced the #ifdef
protection of the init_irq_proc() call by a static inline dummy if
CONFIG_PROC_FS is not set.
Make init_irq_proc() depend on CONFIG_PROC_FS to fix this.
HP input: kill warnings due to suseconds_t differences
Kill compiler warnings related to printf() formats in the input drivers for
various HP9000 machines, which are shared between PA-RISC (suseconds_t is int)
and m68k (suseconds_t is long). As both are 32-bit, it's safe to cast to int.
| include/linux/ssb/ssb.h: In function 'ssb_dma_mapping_error':
| include/linux/ssb/ssb.h:430: error: implicit declaration of function 'pci_dma_mapping_error'
| include/linux/ssb/ssb.h: In function 'ssb_dma_map_single':
| include/linux/ssb/ssb.h:444: error: implicit declaration of function 'pci_map_single'
| include/linux/ssb/ssb.h: In function 'ssb_dma_unmap_single':
| include/linux/ssb/ssb.h:458: error: implicit declaration of function 'pci_unmap_single'
| include/linux/ssb/ssb.h: In function 'ssb_dma_sync_single_for_cpu':
| include/linux/ssb/ssb.h:475: error: implicit declaration of function 'pci_dma_sync_single_for_cpu'
| include/linux/ssb/ssb.h: In function 'ssb_dma_sync_single_for_device':
| include/linux/ssb/ssb.h:493: error: implicit declaration of function 'pci_dma_sync_single_for_device'
or legacy drivers:
| drivers/net/hp100.c: In function 'pdl_map_data':
| drivers/net/hp100.c:291: error: implicit declaration of function 'pci_map_single'
| drivers/net/hp100.c: In function 'hp100_probe1':
| drivers/net/hp100.c:707: error: implicit declaration of function 'pci_alloc_consistent'
| drivers/net/hp100.c:782: error: implicit declaration of function 'pci_free_consistent'
| drivers/net/hp100.c: In function 'hp100_clean_txring':
| drivers/net/hp100.c:1614: error: implicit declaration of function 'pci_unmap_single'
and
| drivers/scsi/aic7xxx_old.c: In function 'aic7xxx_allocate_scb':
| drivers/scsi/aic7xxx_old.c:2573: error: implicit declaration of function 'pci_alloc_consistent'
| drivers/scsi/aic7xxx_old.c: In function 'aic7xxx_done':
| drivers/scsi/aic7xxx_old.c:2697: error: implicit declaration of function 'pci_unmap_single'
| drivers/scsi/aic7xxx_old.c: In function 'aic7xxx_handle_seqint':
| drivers/scsi/aic7xxx_old.c:4275: error: implicit declaration of function 'pci_map_single'
| drivers/scsi/aic7xxx_old.c: In function 'aic7xxx_free':
| drivers/scsi/aic7xxx_old.c:8460: error: implicit declaration of function 'pci_free_consistent'
rely on PCI DMA operations to be always available.
Add #include <asm-generic/pci-dma-compat.h> to <asm/pci.h> to make them happy.
| include/linux/ssb/ssb.h: In function 'ssb_dma_sync_single_range_for_cpu':
| include/linux/ssb/ssb.h:517: error: implicit declaration of function 'dma_sync_single_range_for_cpu'
| include/linux/ssb/ssb.h: In function 'ssb_dma_sync_single_range_for_device':
| include/linux/ssb/ssb.h:538: error: implicit declaration of function 'dma_sync_single_range_for_device'
Add the missing dma_sync_single_range_for_{cpu,device}(), and remove the
`inline' for the non-static function dma_sync_single_for_device().
The nvram and rtc-cmos drivers use the spinlock rtc_lock to protect against
concurrent accesses to the CMOS memory. As m68k doesn't support SMP or preempt
yet, the spinlock calls tend to get optimized away, but not for all
configurations, causing in some rare cases:
Currently Sun 3 support is the first platform option, as the Sun 3 MMU is
incompatible with standard Motorola MMUs. However, this means that
`allmodconfig' enables support for Sun 3, and thus disables support for all
other platforms.
Reverse the logic and move Sun 3 last, so `allmodconfig' enables all
platforms except for Sun 3, increasing compile-coverage.
projects / linux-2.6-omap-h63xx.git / log