> prism54 should set the carrier flags correctly when it thinks the
> link can be used.
Agreed, so sure, this is OK but I rather we turn the carrier on
or off *before* sending an event, like this.
Signed-off-by: Roy Marples <uberlord@gentoo.org> Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 29 Mar 2008 23:10:50 +0000 (00:10 +0100)]
ssb: Turn suspend/resume upside down
Turn the SSB bus suspend mechanism upside down.
Instead of deciding by an internal reference count when to suspend/resume,
let the parent bus call us in their suspend/resume routine.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 29 Mar 2008 20:01:16 +0000 (21:01 +0100)]
b43: Add PIO support for PCMCIA devices
This adds PIO support back (D'oh!) for PCMCIA devices.
This is a complete rewrite of the old PIO code. It does actually work
and we get reasonable performance out of it on a modern machine.
On a PowerBook G4 I get a few MBit for TX and a few more for RX.
So it doesn't work as well as DMA (of course), but it's a _lot_ faster
than the old PIO code (only got a few kBit with that).
The limiting factor is the host CPU speed. So it will generate 100%
CPU usage when the network interface is heavily loaded. A voluntary preemption
point in the RX path makes sure Desktop Latency isn't hurt.
PIO is needed for 16bit PCMCIA devices, as we really don't want to poke with
the braindead DMA mechanisms on PCMCIA sockets. Additionally, not all
PCMCIA sockets do actually support DMA in 16bit mode (mine doesn't).
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 28 Mar 2008 23:33:35 +0000 (16:33 -0700)]
iwlwifi: Eliminate association from beacon
This patch removes association from beacon
using bss_info_change handler for association
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 28 Mar 2008 23:33:34 +0000 (16:33 -0700)]
mac80211: add association capabilty and timing info into bss_conf
This patch adds assocation capability, timestamp (tsf) and beacon interval
to bss_conf. This is required for successful assocation of iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 28 Mar 2008 23:33:33 +0000 (16:33 -0700)]
iwlwifi: eliminate conf_ht
This patch eliminates the use of conf_ht in iwlwifi driver, replacing it
with bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 28 Mar 2008 23:33:32 +0000 (16:33 -0700)]
mac80211: eliminate conf_ht
This patch eliminates the use of conf_ht, replacing it with
bss_info_changed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
That patch breaks mesh config comparison between beacons/probe reponses, so
every beacon from a mesh network would be added as a new bss. Since the
comparison has to be performed for every received beacon I believe it is best to
save the mesh config in a format easy to compare, rather than do a bunch of
unaligned accesses to compare field by field.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on ancient patch by Mickael Hoerdt
<hoerdt@clarinet.u-strasbg.fr>, which is available at
<http://www-r2.u-strasbg.fr/~hoerdt/dev/linux_ipv6_mforwarding/patch-linux-ipv6-mforwarding-0.1a>.
Based on ancient patch by Mickael Hoerdt
<hoerdt@clarinet.u-strasbg.fr>, which is available at
<http://www-r2.u-strasbg.fr/~hoerdt/dev/linux_ipv6_mforwarding/patch-linux-ipv6-mforwarding-0.1a>.
[IPV4] MROUTE: Adjust include files for user-space.
<linux/mroute.h> needs <linux/types.h>.
Avoid including <linux/in.h> in user-space, which conflicts with
standard <netinet/in.h>.
Add basic struct and constant in <linux/pim.h>.
We have been using __NET_IPV6_MAX for adjusting the size of array
for sysctl table, but it does not work any longer because of the
deprecation of NET_IPV6_xxx constants. Let's use DEVCONF_MAX
instead.
Do this by replacing sock_create_kern with inet_ctl_sock_create.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sock_create_kern with inet_ctl_sock_create.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETNS]: Inet control socket should not hold a namespace.
This is a generic requirement, so make inet_ctl_sock_create namespace
aware and create a inet_ctl_sock_destroy wrapper around
sk_release_kernel.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[INET]: Let inet_ctl_sock_create return sock rather than socket.
All upper protocol layers are already use sock internally.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCTP]: Replace socket with sock for SCTP control socket.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[SCTP]: Use inet_ctl_sock_create for control socket creation.
sk->sk_proc->(un)hash is noop right now, so the unification is correct.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[INET]: Rename inet_csk_ctl_sock_create to inet_ctl_sock_create.
This call is nothing common with INET connection sockets code. It
simply creates an unhashes kernel sockets for protocol messages.
Move the new call into af_inet.c after the rename.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This seems a purism as module can't be unloaded, but though if cleanup
method is present it should be correct and clean all staff created.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[DCCP]: Replace socket with sock for reset sending.
Replace dccp_v(4|6)_ctl_socket with sock to unify a code with TCP/ICMP.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[TCP]: Replace socket with sock for reset sending.
Replace tcp_socket with tcp_sock. This is more effective (less
derefferences on fast paths). Additionally, the approach is unified to
one used in ICMP.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Templin, Fred L [Tue, 11 Mar 2008 22:35:59 +0000 (18:35 -0400)]
[IPV6] SIT: Add PRL management for ISATAP.
This patch updates the Linux the Intra-Site Automatic Tunnel Addressing
Protocol (ISATAP) implementation. It places the ISATAP potential router
list (PRL) in the kernel and adds three new private ioctls for PRL
management.
[Add several changes of structure name, constant names etc. - yoshfuji]
Signed-off-by: Fred L. Templin <fred.l.templin@boeing.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ohci: fix 2 timers to fire at jiffies + 1s
USB: Allow initialization of broken keyspan serial adapters.
USB: fix bug in sg initialization in usbtest
USB: serial: fix regression in Visor/Palm OS module for kernels >= 2.6.24
USB: cp2101: Add identifiers for the Telegesys ETRX2USB
USB: serial: ti_usb_3410_5052: Correct TUSB3410 endpoint requirements.
USB: another ehci_iaa_watchdog fix
Andrew Morton [Wed, 2 Apr 2008 20:04:52 +0000 (13:04 -0700)]
alpha: get_current(): don't add zero to current_thread_info()->task
A nasty compile error:
In file included from security/keys/internal.h:16,
from security/keys/sysctl.c:14:
include/linux/key-ui.h: In function 'key_permission':
include/linux/key-ui.h:51: error: invalid use of undefined type 'struct task_struct'
apparently the compiler has decided that it needs to know sizeof(task_struct)
so that it can add zero to a task_struct* (which is rather dumb of it).
Getting task_struct in scope in these deeply-nested headers is scary-looking,
so let's just remove the "+ 0".
Cc: David Howells <dhowells@redhat.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Markers do not mix well with CONFIG_PREEMPT_RCU because it uses
preempt_disable/enable() and not rcu_read_lock/unlock for minimal
intrusiveness. We would need call_sched and sched_barrier primitives.
Currently, the modification (connection and disconnection) of probes
from markers requires changes to the data structure done in RCU-style :
a new data structure is created, the pointer is changed atomically, a
quiescent state is reached and then the old data structure is freed.
The quiescent state is reached once all the currently running
preempt_disable regions are done running. We use the call_rcu mechanism
to execute kfree() after such quiescent state has been reached.
However, the new CONFIG_PREEMPT_RCU version of call_rcu and rcu_barrier
does not guarantee that all preempt_disable code regions have finished,
hence the race.
The "proper" way to do this is to use rcu_read_lock/unlock, but we don't
want to use it to minimize intrusiveness on the traced system. (we do
not want the marker code to call into much of the OS code, because it
would quickly restrict what can and cannot be instrumented, such as the
scheduler).
The temporary fix, until we get call_rcu_sched and rcu_barrier_sched in
mainline, is to use synchronize_sched before each call_rcu calls, so we
wait for the quiescent state in the system call code path. It will slow
down batch marker enable/disable, but will make sure the race is gone.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the problem that makedumpfile sometimes fails on x86_64 machine.
This patch adds the symbol "phys_base" to a vmcoreinfo data. The
vmcoreinfo data has the minimum debugging information only for dump
filtering. makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.
On x86_64 kernel which compiled with CONFIG_PHYSICAL_START=0x0 and
CONFIG_RELOCATABLE=y, makedumpfile fails like the following:
# makedumpfile -d31 /proc/vmcore dumpfile
The kernel version is not supported.
The created dumpfile may be incomplete.
_exclude_free_page: Can't get next online node.
makedumpfile Failed.
#
The cause is the lack of the symbol "phys_base" in a vmcoreinfo data.
If the symbol "phys_base" does not exist, makedumpfile considers an
x86_64 kernel as non relocatable. As the result, makedumpfile
misunderstands the physical address where the kernel is loaded, and it
cannot translate a kernel virtual address to physical address correctly.
To fix this problem, this patch adds the symbol "phys_base" to a
vmcoreinfo data.
efs: update error msg to not refer to deleted read_inode()
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marc Pignat [Wed, 2 Apr 2008 20:04:42 +0000 (13:04 -0700)]
atmel_serial: fix uart/console concurrent access
Strange chars appear on the serial port when a printk and a printf
happens at the same time. This is caused by the pdc sending chars while
atmel_console_write (called from printk) is executing
Concurent access of uart and console to the same port leads to corrupted
data to be transmitted, so disable tx dma (PDC) while writing to the
console.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atmel_serial: avoid stopping pdc during transmission
I found a problem related to losing data during pdc transmission in
atmel_serial: connect ttyS1 with ttyS2 using a loopback cable, send 30
byte of packet from one to the other and waiting for 30 byte. On the
other side just read and echo the data received.
We always call atmel_tx_dma() from the tasklet regardless of what interrupt
triggered it.
Signed-off-by: michael <trimarchi@gandalf.sssup.it> Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kvm: provide kvm.h for all architecture: fixes headers_install
Currently include/linux/kvm.h is not considered by make headers_install,
because Kbuild cannot handle " unifdef-$(CONFIG_FOO) += foo.h. This problem
was introduced by
KVM: Export include/linux/kvm.h only if $ARCH actually supports KVM
Currently, make headers_check barfs due to <asm/kvm.h>, which <linux/kvm.h>
includes, not existing. Rather than add a zillion <asm/kvm.h>s, export kvm.
only if the arch actually supports it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
which makes this an 2.6.25 regression.
One way of solving the issue is to enhance Kbuild, but Avi and David conviced
me, that changing headers_install is not the way to go. This patch changes
the definition for linux/kvm.h to unifdef-y.
If unifdef-y is used for linux/kvm.h "make headers_check" will fail on all
architectures without asm/kvm.h. Therefore, this patch also provides
asm/kvm.h on all architectures.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Avi Kivity <avi@qumranet.com> Cc: Sam Ravnborg <sam@ravnborg.org Cc: David Woodhouse <dwmw2@infradead.org> Cc: <linux-arch@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Kennedy [Fri, 28 Mar 2008 21:50:30 +0000 (14:50 -0700)]
USB: ohci: fix 2 timers to fire at jiffies + 1s
Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ). The timer would then fire at time (0 <= T <
HZ).
Fix them to use round_jiffies(jiffies + HZ);
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clark Rawlins [Thu, 27 Mar 2008 13:56:17 +0000 (09:56 -0400)]
USB: Allow initialization of broken keyspan serial adapters.
Fixes the keyspan driver after the addition of additional
checking of driver requirements introduced in usb-serial.c
commit 063a2da8f01806906f7d7b1a1424b9afddebc443. The initialization
of the keyspan usb_serial_driver structs were not initializing the
num_interrupt_out field and the additional checking was rejecting
the end point so the driver wouldn't finish initializing.
This commit initializes the fields to NUM_DONT_CARE.
It works for the keyspan USA-49WG and doesn't break the USA-19HS
which are the two keyspan devices I have to test with.
Alan Stern [Thu, 27 Mar 2008 14:15:22 +0000 (10:15 -0400)]
USB: fix bug in sg initialization in usbtest
This patch (as1062) fixes a bug in the scatter-gather initialization
code in the usbtest driver. When the sg-helper conversion was
performed, it wasn't done correctly.
Brad Sawatzky [Wed, 26 Mar 2008 02:32:43 +0000 (22:32 -0400)]
USB: serial: fix regression in Visor/Palm OS module for kernels >= 2.6.24
Fixes a bug/inconsistency revealed by the additional sanity checking in
commit 063a2da8f01806906f7d7b1a1424b9afddebc443
introduced in the original 2.6.24 branch.
The Handspring Visor / PalmOS 4 device structure defines .num_bulk_out=2
but the usb-serial probe returns num_bulk_out=3, triggering the check in
the above commit and forcing a bail out when the device (a Garmin iQue in
my case) attempts to connect. The patch bumps the expected number of
endpoints to 3.
FWIW, this patch will probably solve the following kernel bug report for
Treo users (identical symptoms, different model PalmOS units):
<http://bugzilla.kernel.org/show_bug.cgi?id=10118>
The changes introduced in commit 063a2da8f01806906f7d7b1a1424b9afddebc443 changed the semantics of the
num_interrupt_in, num_interrupt_out, num_bulk_in and num_bulk_out
entries of the usb_serial_driver struct to be the number of endpoints
the device has when probed.
This patch changes the ti_1port_device usb_serial_driver struct to
reflect this change. The single port devices only have 1
bulk_out endpoint in their initial configuration, and so this patch
changes the number of other types to NUM_DONT_CARE.
The same change probably needs doing to the ti_2port_device struct,
but I don't have a two port device at hand.
David Brownell [Wed, 2 Apr 2008 20:40:20 +0000 (13:40 -0700)]
USB: another ehci_iaa_watchdog fix
This patch, suggested by Alan Stern, fixes the hung USB issues
on my notebook from suspend/resume cycles.
It does so by eliminating some confusion about the internal state
machine associated with unlinking from the EHCI async schedule ring,
which caused a recent regression:
http://bugzilla.kernel.org/show_bug.cgi?id=10345
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are a couple of possible races on suspend/resume.
First the driver needs to block new packets from being queued for Tx.
The other less likely problem is the watchdog timer going off
during resume.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (7486): radio-cadet: wrap PNP probe code in #ifdef CONFIG_PNP
V4L/DVB (7485): v4l2-int-device.c: add MODULE_LICENSE
V4L/DVB (7466): Avoid minor model number warning when an OEM HVR1250 board is detected
V4L/DVB (7465): Fix eeprom parsing and errors on the HVR1800 products
V4L/DVB (7464): Convert driver to use a single SRAM memory map
V4L/DVB (7461): bttv: fix missed index check
V4L/DVB (7400): bttv: Add a radio compat_ioctl file operation
V4L/DVB (7278): bttv: Re-enable radio tuner support for VIDIOCGFREQ/VIDIOCSFREQ ioctls
V4L/DVB (7277): bttv: Re-enabling radio support requires the use of struct bttv_fh
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mvsas: check subsystem id
[SCSI] mvsas: get phy info.
[SCSI] mvsas: fix the buffer of rx DMA overflow bug
[SCSI] mvsas: retry aborting task.
[SCSI] mvsas: check hd whether unplugged
[SCSI] mvsas : interrupt handling
[SCSI] mvsas: a tag handler implementation
[SCSI] mvsas: fill in error info record and phy mode6 bits.
[SCSI] libsas: Warn if ATA device detected but CONFIG_SCSI_SAS_ATA not set
[SCSI] hosts.c: fixes for "no error" reported after error scenarios
Revert "[SCSI] fix bsg queue oops with iscsi logout"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
[VLAN]: Proc entry is not renamed when vlan device name changes.
[IPV6]: Fix ICMP relookup error path dst leak
[ATM] drivers/atm/iphase.c: compilation warning fix
IPv6: do not create temporary adresses with too short preferred lifetime
IPv6: only update the lifetime of the relevant temporary address
bluetooth : __rfcomm_dlc_close lock fix
bluetooth : use lockdep sub-classes for diffrent bluetooth protocol
[ROSE/AX25] af_rose: rose_release() fix
mac80211: correct use_short_preamble handling
b43: Fix PCMCIA IRQ routing
b43: Add DMA mapping failure messages
mac80211: trigger ieee80211_sta_work after opening interface
[LLC]: skb allocation size for responses
[IP] UDP: Use SEQ_START_TOKEN.
[NET]: Remove Documentation/networking/sk98lin.txt
[ATM] atm/idt77252.c: Make 2 functions static
[ATM]: Make atm/he.c:read_prom_byte() static
[IPV6] MCAST: Ensure to check multicast listener(s).
[LLC]: Kill llc_station_mac_sa symbol export.
forcedeth: fix locking bug with netconsole
...
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
selinux: handle files opened with flags 3 by checking ioctl permission
SLAB_DESTROY_BY_RCU is not a direct substitute for normal call_rcu()
freeing, since it'll page freeing but NOT object freeing. So change
cfq to do the freeing on its own.
Signed-off-by: Fabio Checconi <fabio@gandalf.sssup.it> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Looking a bit closer into this regression the reason this can't be
right is that dma_addr common default is BLK_BOUNCE_HIGH and most
machines have less than 4G. So if you do:
So for 99% of hardware this will trigger unnecessary GFP_DMA
allocations and isa pooling operations.
Also note how the 32bit code still does b_pfn < blk_max_low_pfn.
I guess this is what you were looking after. I didn't verify but as
far as I can tell, this will stop the regression with isa dma
operations at boot for 99% of blkdev/memory combinations out there and
I guess this fixes the setups with >4G of ram and 32bit pci cards as
well (this also retains symmetry with the 32bit code).
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Herbert Xu [Wed, 2 Apr 2008 07:06:09 +0000 (00:06 -0700)]
[IPV6]: Fix ICMP relookup error path dst leak
When we encounter an error while looking up the dst the second
time we need to drop the first dst. This patch is pretty much
the same as the one for IPv4.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the warning messages:
drivers/atm/iphase.c:961: warning: 'tcnter' defined but not used
drivers/atm/iphase.c:963: warning: 'xdump' defined but not used
tcnter and xdump() are used only in debug build
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: do not create temporary adresses with too short preferred lifetime
From RFC341:
A temporary address is created only if this calculated Preferred
Lifetime is greater than REGEN_ADVANCE time units. In particular, an
implementation must not create a temporary address with a zero
Preferred Lifetime.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: only update the lifetime of the relevant temporary address
When receiving a prefix information from a routeur, only update the
lifetimes of the temporary address associated with that prefix.
Otherwise if one deprecated prefix is advertized, all your temporary
addresses will become deprecated.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
rose_release() doesn't release sockets properly, e.g. it skips
sock_orphan(), so OOPSes are triggered in sock_def_write_space(),
which was observed especially while ROSE skbs were kfreed from
ax25_frames_acked(). There is also sock_hold() and lock_sock() added -
similarly to ax25_release(). Thanks to Bernard Pidoux for substantial
help in debugging this problem.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Reported-and-tested-by: Bernard Pidoux <bpidoux@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log