Stefan Becker [Tue, 1 Jul 2008 16:19:22 +0000 (19:19 +0300)]
USB: fix interrupt disabling for HCDs with shared interrupt handlers
USB: fix interrupt disabling for HCDs with shared interrupt handlers
As has been discussed several times on LKML, IRQF_SHARED | IRQF_DISABLED
doesn't work reliably, i.e. a shared interrupt handler CAN'T be certain to
be called with interrupts disabled. Most USB HCD handlers use IRQF_DISABLED
and therefore havoc can break out if they share their interrupt with a
handler that doesn't use it.
On my test machine the yenta_socket interrupt handler (no IRQF_DISABLED)
was registered before ehci_hcd and one uhci_hcd instance. Therefore all
usb_hcd_irq() invocations for ehci_hcd and for one uhci_hcd instance
happened with interrupts enabled. That led to random lockups as USB core
HCD functions that acquire the same spinlock could be called twice
from interrupt handlers.
This patch updates usb_hcd_irq() to always disable/restore interrupts.
usb_add_hcd() will silently remove any IRQF_DISABLED requested from HCD code.
Signed-off-by: Stefan Becker <stefan.becker@nokia.com> Cc: stable <stable@kernel.org> Acked-by: David Brownell <david-b@pacbell.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jon K Hellan [Tue, 24 Jun 2008 09:43:13 +0000 (11:43 +0200)]
USB: New device ID for ftdi_sio driver
Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.
The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.
(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:
David Brownell [Sat, 14 Jun 2008 06:59:54 +0000 (23:59 -0700)]
USB: ohci - record data toggle after unlink
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle. This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because
(a) about half the time the data toggle bit was correct;
(b) canceling such URBs is unusual; and
(c) the few drivers which cancel these URBs either
[1] do it only as part of shutting down, or
[2] have fault recovery logic, which recovers.
For those transfer types, the toggle is normally written back
into the ED when each TD is retired. But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.
The fix is simple: the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.
(Issue found by leonidv11@gmail.com ...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Leonid <leonidv11@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 14 Jun 2008 06:56:48 +0000 (23:56 -0700)]
USB: ehci - fix timer regression
This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior. The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.
This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Leonid <leonidv11@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 17 Jun 2008 20:30:48 +0000 (22:30 +0200)]
USB: fix cdc-acm resume()
cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ben Dooks [Sun, 8 Jun 2008 16:20:11 +0000 (17:20 +0100)]
OHCI: Fix problem if SM501 and another platform driver is selected
If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fix' of git://aeryn.fluff.org.uk/bjdooks/linux:
I2C: S3C2410: Add MODULE_ALIAS() for s3c2440 device.
I2C: S3C2410: Fixup error codes returned rom a transfer.
I2C: S3C2410: Check ACK on byte transmission
Merge branch 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.26' of git://git.kernel.dk/linux-2.6-block:
Properly notify block layer of sync writes
block: Fix the starving writes bug in the anticipatory IO scheduler
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (8178): uvc: Fix compilation breakage for the other drivers, if uvc is selected
V4L/DVB (8145a): USB Video Class driver
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
[ARM] 5117/1: pxafb: fix __devinit/exit annotations
[ARM] Export dma_sync_sg_for_device()
[ARM] 5109/1: Mark rtc sa1100 driver as wakeup source before registering it
[ARM] 5116/1: pxafb: cleanup and fix order of failure handling
[ARM] 5115/1: pxafb: fix ifdef for command line option handling
ARM: OMAP: Correcting the gpmc prefetch control register address
ARM: OMAP: DMA: Don't mark channel active in omap_enable_channel_irq
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix divide error when trying to configure rt_period to zero
Merge branch 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Fix bad hint about irqs in i2c.h
i2c: Documentation: fix device matching description
Merge branch 'for-2.6.26' of git://neil.brown.name/md
* 'for-2.6.26' of git://neil.brown.name/md:
Fix error paths if md_probe fails.
Don't acknowlege that stripe-expand is complete until it really is.
Ensure interrupted recovery completed properly (v1 metadata plus bitmap)
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc/mpc5200: Fix lite5200b suspend/resume
powerpc/legacy_serial: Bail if reg-offset/shift properties are present
powerpc/bootwrapper: update for initrd with simpleImage
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (55 commits)
net: fib_rules: fix error code for unsupported families
netdevice: Fix wrong string handle in kernel command line parsing
net: Tyop of sk_filter() comment
netlink: Unneeded local variable
net-sched: fix filter destruction in atm/hfsc qdisc destruction
net-sched: change tcf_destroy_chain() to clear start of filter list
ipv4: fix sysctl documentation of time related values
mac80211: don't accept WEP keys other than WEP40 and WEP104
hostap: fix sparse warnings
hostap: don't report useless WDS frames by default
textsearch: fix Boyer-Moore text search bug
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
netlabel: Fix a problem when dumping the default IPv6 static labels
net/inet_lro: remove setting skb->ip_summed when not LRO-able
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
CONNECTOR: add a proc entry to list connectors
netlink: Fix some doc comments in net/netlink/attr.c
tcp: /proc/net/tcp rto,ato values not scaled properly (v2)
include/linux/netdevice.h: don't export MAX_HEADER to userspace
...
When scheduled swaps occur, we need to blit between front & back
buffers. If the buffers are tiled, we need to set the appropriate
XY_SRC_COPY tile bit, but only on 965 chips, since it will cause
corruption on pre-965 (e.g. 945).
Bug reported by and fix tested by Tomas Janousek <tomi@nomi.cz>.
| linux/drivers/input/ff-core.c: In function 'input_ff_upload':
| linux/drivers/input/ff-core.c:172: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c: In function 'erase_effect':
| linux/drivers/input/ff-core.c:197: error: dereferencing pointer to incomplete type
| linux/drivers/input/ff-core.c:204: error: dereferencing pointer to incomplete type
| make[4]: *** [drivers/input/ff-core.o] Error 1
As the incomplete type is `struct task_struct', including <linux/sched.h> fixes
it.
Alex Chiang [Wed, 2 Jul 2008 02:02:23 +0000 (20:02 -0600)]
PCI: acpiphp: cleanup notify handler on all root bridges
During the development of the physical PCI slot patch series, Gary Hade
kept on reporting strange oopses due to interactions between pci_slot
and acpiphp.
http://lkml.org/lkml/2007/11/28/319
find_root_bridges() unconditionally installs
handle_hotplug_event_bridge() as an ACPI_SYSTEM_NOTIFY handler for all
root bridges.
However, during module cleanup, remove_bridge() will only remove the
notify handler iff the root bridge had a hot-pluggable slot directly
underneath. That is:
root bridge -> hotplug slot
But, if the topology looks like either of the following:
Then we currently do not remove the notify handler from that root
bridge.
This can cause a kernel oops if we modprobe acpiphp later and it gets
loaded somewhere else in memory. If the root bridge then receives a
hotplug event, it will then attempt to call a stale, non-existent notify
handler and we blow up.
Much thanks goes to Gary Hade for his persistent debugging efforts.
Signed-off-by: Alex Chiang <achiang@hp.com> Signed-off-by: Gary Hade <garyhade@us.ibm.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Milan Broz [Wed, 2 Jul 2008 08:34:28 +0000 (09:34 +0100)]
dm crypt: use cond_resched
Add cond_resched() to prevent monopolising CPU when processing large bios.
dm-crypt processes encryption of bios in sector units. If the bio request
is big it can spend a long time in the encryption call.
Signed-off-by: Milan Broz <mbroz@redhat.com> Tested-by: Yan Li <elliot.li.tech@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Wang Chen [Wed, 2 Jul 2008 02:57:19 +0000 (19:57 -0700)]
netdevice: Fix wrong string handle in kernel command line parsing
v1->v2: Use strlcpy() to ensure s[i].name be null-termination.
1. In netdev_boot_setup_add(), a long name will leak.
ex. : dev=21,0x1234,0x1234,0x2345,eth123456789verylongname.........
2. In netdev_boot_setup_check(), mismatch will happen if s[i].name
is a substring of dev->name.
ex. : dev=...eth1 dev=...eth11
[ With feedback from Ben Hutchings. ]
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4: fix sysctl documentation of time related values
These sysctl values are time related and all use the same routine
(proc_dointvec_jiffies) that internally converts from seconds to jiffies.
The code is fine, the documentation is just wrong.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tim Yamin [Tue, 17 Jun 2008 08:33:14 +0000 (09:33 +0100)]
powerpc/mpc5200: Fix lite5200b suspend/resume
Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:
1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: Tim Yamin <plasm@roo.me.uk> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
John Linn [Tue, 1 Jul 2008 17:52:41 +0000 (10:52 -0700)]
powerpc/legacy_serial: Bail if reg-offset/shift properties are present
The legacy serial driver does not work with an 8250 type UART that is
described in the device tree with the reg-offset and reg-shift
properties. This change makes legacy_serial ignore these devices.
Signed-off-by: John Linn <john.linn@xilinx.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Wolfram Sang [Tue, 1 Jul 2008 20:38:18 +0000 (22:38 +0200)]
i2c: Fix bad hint about irqs in i2c.h
i2c.h mentions -1 as a not-issued irq. This false hint was taken by
of_i2c and caused crashes. Don't give any advice as 'no irq' is not
consistent across all architectures yet and it is not needed internally
by the i2c-core.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
The matching process described for new style clients in
Documentation/i2c/writing-clients is classed as out-of-date
as it requires the presence of an .id_table entry in the
driver's i2c_driver entry.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ben Hutchings [Tue, 1 Jul 2008 16:18:17 +0000 (17:18 +0100)]
PCI: Restrict VPD read permission to root
Some PCI devices will lock up if we attempt to read from VPD addresses
beyond some device-dependent limit. Until we can identify these
devices and adjust the file size accordingly, only let root read VPD
through sysfs to prevent a DoS by normal users.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ben Dooks [Tue, 1 Jul 2008 10:59:41 +0000 (11:59 +0100)]
I2C: S3C2410: Check ACK on byte transmission
We should check for the reception of an ACK after transmitting each
data byte. The address send has been correctly checking this, but the
data write byte state should have also been checking for these failures.
As part of the same fix, we remove the ACK checking from the receive
path where it should not have been checking for an ACK which our hardware
was sending.
Gautham R Shenoy [Fri, 27 Jun 2008 04:47:38 +0000 (10:17 +0530)]
rcu: fix hotplug vs rcu race
Dhaval Giani reported this warning during cpu hotplug stress-tests:
| On running kernel compiles in parallel with cpu hotplug:
|
| WARNING: at arch/x86/kernel/smp.c:118
| native_smp_send_reschedule+0x21/0x36()
| Modules linked in:
| Pid: 27483, comm: cc1 Not tainted 2.6.26-rc7 #1
| [...]
| [<c0110355>] native_smp_send_reschedule+0x21/0x36
| [<c014fe8f>] force_quiescent_state+0x47/0x57
| [<c014fef0>] call_rcu+0x51/0x6d
| [<c01713b3>] __fput+0x130/0x158
| [<c0171231>] fput+0x17/0x19
| [<c016fd99>] filp_close+0x4d/0x57
| [<c016fdff>] sys_close+0x5c/0x97
IMHO the warning is a spurious one.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
However, a cpu might have been offlined _just_ before we disabled irqs
while entering force_quiescent_state(). And rcu subsystem might not yet
have handled the CPU_DEAD notification, leading to the offlined cpu's
bit being set in the rcp->cpumask.
Hence cpumask = (rcp->cpumask & cpu_online_map) to prevent sending
smp_reschedule() to an offlined CPU.
Here's the timeline:
CPU_A CPU_B
--------------------------------------------------------------
cpu_down(): .
. .
. .
stop_machine(): /* disables preemption, .
* and irqs */ .
. .
. .
take_cpu_down(); .
. .
. .
. .
cpu_disable(); /*this removes cpu .
*from cpu_online_map .
*/ .
. .
. .
restart_machine(); /* enables irqs */ .
------WINDOW DURING WHICH rcp->cpumask is stale ---------------
. call_rcu();
. /* disables irqs here */
. .force_quiescent_state();
.CPU_DEAD: .for_each_cpu(rcp->cpumask)
. . smp_send_reschedule();
. .
. . WARN_ON() for offlined CPU!
.
.
.
rcu_cpu_notify:
.
-------- WINDOW ENDS ------------------------------------------
rcu_offline_cpu() /* Which calls cpu_quiet()
* which removes
* cpu from rcp->cpumask.
*/
If a new batch was started just before calling stop_machine_run(), the
"tobe-offlined" cpu is still present in rcp-cpumask.
During a cpu-offline, from take_cpu_down(), we queue an rt-prio idle
task as the next task to be picked by the scheduler. We also call
cpu_disable() which will disable any further interrupts and remove the
cpu's bit from the cpu_online_map.
Once the stop_machine_run() successfully calls take_cpu_down(), it calls
schedule(). That's the last time a schedule is called on the offlined
cpu, and hence the last time when rdp->passed_quiesc will be set to 1
through rcu_qsctr_inc().
But the cpu_quiet() will be on this cpu will be called only when the
next RCU_SOFTIRQ occurs on this CPU. So at this time, the offlined CPU
is still set in rcp->cpumask.
Now coming back to the idle_task which truely offlines the CPU, it does
check for a pending RCU and raises the softirq, since it will find
rdp->passed_quiesc to be 0 in this case. However, since the cpu is
offline I am not sure if the softirq will trigger on the CPU.
Even if it doesn't the rcu_offline_cpu() will find that rcp->completed
is not the same as rcp->cur, which means that our cpu could be holding
up the grace period progression. Hence we call cpu_quiet() and move
ahead.
But because of the window explained in the timeline, we could still have
a call_rcu() before the RCU subsystem executes it's CPU_DEAD
notification, and we send smp_send_reschedule() to offlined cpu while
trying to force the quiescent states. The appended patch adds comments
and prevents checking for offlined cpu everytime.
cpu_online_map is updated by the _cpu_down() using stop_machine_run().
Since force_quiescent_state is invoked from irqs disabled section,
stop_machine_run() won't be executing while a cpu is executing
force_quiescent_state(). Hence the cpu_online_map is stable while we're
in the irq disabled section.
fsync_buffers_list() and sync_dirty_buffer() both issue async writes and
then immediately wait on them. Conceptually, that makes them sync writes
and we should treat them as such so that the IO schedulers can handle
them appropriately.
This patch fixes a write starvation issue that Lin Ming reported, where
xx is stuck for more than 2 minutes because of a large number of
synchronous IO in the system:
Lin Ming confirms that this patch fixes the issue. I've run tests with
it for the past week and no ill effects have been observed, so I'm
proposing it for inclusion into 2.6.26.
Divyesh Shah [Mon, 16 Jun 2008 16:37:08 +0000 (18:37 +0200)]
block: Fix the starving writes bug in the anticipatory IO scheduler
AS scheduler alternates between issuing read and write batches. It does
the batch switch only after all requests from the previous batch are
completed.
When switching to a write batch, if there is an on-going read request,
it waits for its completion and indicates its intention of switching by
setting ad->changed_batch and the new direction but does not update the
batch_expire_time for the new write batch which it does in the case of
no previous pending requests.
On completion of the read request, it sees that we were waiting for the
switch and schedules work for kblockd right away and resets the
ad->changed_data flag.
Now when kblockd enters dispatch_request where it is expected to pick
up a write request, it in turn ends the write batch because the
batch_expire_timer was not updated and shows the expire timestamp for
the previous batch.
This results in the write starvation for all the cases where there is
the intention for switching to a write batch, but there is a previous
in-flight read request and the batch gets reverted to a read_batch
right away.
This also holds true in the reverse case (switching from a write batch
to a read batch with an in-flight write request).
I've checked that this bug exists on 2.6.11, 2.6.18, 2.6.24 and
linux-2.6-block git HEAD. I've tested the fix on x86 platforms with
SCSI drives where the driver asks for the next request while a current
request is in-flight.
This patch is based off linux-2.6-block git HEAD.
Bug reproduction:
A simple scenario which reproduces this bug is:
- dd if=/dev/hda3 of=/dev/null &
- lilo
The lilo takes forever to complete.
This can also be reproduced fairly easily with the earlier dd and
another test
program doing msync().
The example test program below should print out a message after every
iteration
but it simply hangs forever. With this bugfix it makes forward progress.
====
Example test program using msync() (thanks to suleiman AT google DOT
com)
I'm checking as soon as possible for the period not being zero since, if
it is, going ahead is useless. This way we also save a mutex_lock() and
a read_lock() wrt doing it inside tg_set_bandwidth() or
__rt_schedulable().
Tony Luck [Mon, 30 Jun 2008 22:03:14 +0000 (15:03 -0700)]
[IA64] Bugfix for system with 32 cpus
On a system where there are no hot pluggable cpus "additional_cpus"
is still set to -1 at the point where we call per_cpu_scan_finalize().
If we didn't find an SRAT table and so pick the default "32" for the
number of cpus, when we get to:
high_cpu = min(high_cpu + reserve_cpus, NR_CPUS);
we will end up initializing for just 31 cpus ... and so we will
die horribly when bringing up cpu#32.
Laurent Pinchart [Mon, 30 Jun 2008 18:04:50 +0000 (15:04 -0300)]
V4L/DVB (8145a): USB Video Class driver
This driver supports video input devices compliant with the USB Video Class
specification. This means lots of currently manufactured webcams, and probably
most of the future ones.
mac80211: don't accept WEP keys other than WEP40 and WEP104
This patch makes mac80211 refuse a WEP key whose length is not WEP40 nor
WEP104.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Fri, 27 Jun 2008 20:19:58 +0000 (16:19 -0400)]
hostap: fix sparse warnings
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joonwoo Park [Mon, 30 Jun 2008 19:42:23 +0000 (12:42 -0700)]
textsearch: fix Boyer-Moore text search bug
The current logic has a bug which cannot find matching pattern, if the
pattern is matched from the first character of target string.
for example:
pattern=abc, string=abcdefg
pattern=a, string=abcdefg
Searching algorithm should return 0 for those things.
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jozsef Kadlecsik [Mon, 30 Jun 2008 19:41:30 +0000 (12:41 -0700)]
netfilter: nf_conntrack_tcp: fixing to check the lower bound of valid ACK
Lost connections was reported by Thomas Bätzler (running 2.6.25 kernel) on
the netfilter mailing list (see the thread "Weird nat/conntrack Problem
with PASV FTP upload"). He provided tcpdump recordings which helped to
find a long lingering bug in conntrack.
In TCP connection tracking, checking the lower bound of valid ACK could
lead to mark valid packets as INVALID because:
- We have got a "higher or equal" inequality, but the test checked
the "higher" condition only; fixed.
- If the packet contains a SACK option, it could occur that the ACK
value was before the left edge of our (S)ACK "window": if a previous
packet from the other party intersected the right edge of the window
of the receiver, we could move forward the window parameters beyond
accepting a valid ack. Therefore in this patch we check the rightmost
SACK edge instead of the ACK value in the lower bound of valid (S)ACK
test.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Catalin Marinas [Fri, 27 Jun 2008 14:15:12 +0000 (15:15 +0100)]
[ARM] 5131/1: Annotate platform_secondary_init with trace_hardirqs_off
This patch annotates the platform_secondary_init function in
arch/arm/mach-realview/platsmp.c with trace_hardirqs_off to avoid a
warning when LOCKDEP and TRACE_IRQFLAGS are enabled.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds [Mon, 30 Jun 2008 15:56:57 +0000 (08:56 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ptrace GET/SET FPXREGS broken
x86: fix cpu hotplug crash
x86: section/warning fixes
x86: shift bits the right way in native_read_tscp
Dmitry Torokhov [Thu, 26 Jun 2008 15:30:02 +0000 (11:30 -0400)]
Input: fix locking in force-feedback core
The newly added event_lock spinlock in the input core disallows sleeping
and therefore using mutexes in event handlers. Convert force-feedback
core to rely on event_lock instead of mutex to protect slots allocated
for fore-feedback effects. The original mutex is still used to serialize
uploading and erasing of effects.
struct user_fxsr_struct {
unsigned short cwd;
unsigned short swd;
unsigned short twd;
unsigned short fop;
long fip;
long fcs;
long foo;
long fos;
long mxcsr;
long reserved;
long st_space[32]; /* 8*16 bytes for each FP-reg = 128 bytes */
long xmm_space[32]; /* 8*16 bytes for each XMM-reg = 128 bytes */
long padding[56];
};
int main(void)
{
pid_t pid;
pid = fork();
switch(pid){
case -1:/* error */
break;
case 0:/* child */
child();
break;
default:
parent(pid);
break;
}
return 0;
}
int child(void)
{
ptrace(PTRACE_TRACEME);
kill(getpid(), SIGSTOP);
sleep(10);
return 0;
}
int parent(pid_t pid)
{
int ret;
struct user_fxsr_struct fpxregs;
In function _cpu_up, the panic happens when calling
__raw_notifier_call_chain at the second time. Kernel doesn't panic when
calling it at the first time. If just say because of nr_cpu_ids, that's
not right.
By checking the source code, I found that function do_boot_cpu is the culprit.
Consider below call chain:
_cpu_up=>__cpu_up=>smp_ops.cpu_up=>native_cpu_up=>do_boot_cpu.
So do_boot_cpu is called in the end. In do_boot_cpu, if
boot_error==true, cpu_clear(cpu, cpu_possible_map) is executed. So later
on, when _cpu_up calls __raw_notifier_call_chain at the second time to
report CPU_UP_CANCELED, because this cpu is already cleared from
cpu_possible_map, get_cpu_sysdev returns NULL.
Many resources are related to cpu_possible_map, so it's better not to
change it.
Below patch against 2.6.26-rc7 fixes it by removing the bit clearing in
cpu_possible_map.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (42 commits)
V4L/DVB (8108): Fix open/close race in saa7134
V4L/DVB (8100): V4L/vivi: fix possible memory leak in vivi_fillbuff
V4L/DVB (8097): xc5000: check device hardware state to determine if firmware download is needed
V4L/DVB (8096): au8522: prevent false-positive lock status
V4L/DVB (8092): videodev: simplify and fix standard enumeration
V4L/DVB (8075): stv0299: Uncorrected block count and bit error rate fixed
V4L/DVB (8074): av7110: OSD transfers should not be interrupted
V4L/DVB (8073): av7110: Catch another type of ARM crash
V4L/DVB (8071): tda10023: Fix possible kernel oops during initialisation
V4L/DVB (8069): cx18: Fix S-Video and Compsite inputs for the Yuan MPC718 and enable card entry
V4L/DVB (8068): cx18: Add I2C slave reset via GPIO upon initialization
V4L/DVB (8067): cx18: Fix firmware load for case when digital capture happens first
V4L/DVB (8066): cx18: Fix audio mux input definitions for HVR-1600 Line In 2 and FM radio
V4L/DVB (8063): cx18: Fix unintended auto configurations in cx18-av-core
V4L/DVB (8061): cx18: only select tuner / frontend modules if !DVB_FE_CUSTOMISE
V4L/DVB (8048): saa7134: Fix entries for Avermedia A16d and Avermedia E506
V4L/DVB (8044): au8522: tuning optimizations
V4L/DVB (8043): au0828: add support for additional USB device id's
V4L/DVB (8042): DVB-USB UMT-010 channel scan oops
V4L/DVB (8040): soc-camera: remove soc_camera_host_class class
...
Linus Torvalds [Sun, 29 Jun 2008 19:22:30 +0000 (12:22 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
dock: bay: Don't call acpi_walk_namespace() when ACPI is disabled.
ACPI: don't walk tables if ACPI was disabled
thermal: Create CONFIG_THERMAL_HWMON=n
Removed vmlinux* rule because it matches too many useful files, replacing
it with rules matching filetype by filename (e.g. *.gz). Also unignored
.mailmap from the top directory. Added a comment telling the user how to
check for tracked files being ignored.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 29 Jun 2008 19:15:10 +0000 (12:15 -0700)]
Merge branch 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current
* 'audit.b52' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] remove useless argument type in audit_filter_user()
[PATCH] audit: fix kernel-doc parameter notation
[PATCH] kernel/audit.c: nlh->nlmsg_type is gotten more than once
Dmitry Adamushko [Sat, 28 Jun 2008 22:16:56 +0000 (00:16 +0200)]
sched: fix cpu hotplug
the CPU hotplug problems (crashes under high-volume unplug+replug
tests) seem to be related to migrate_dead_tasks().
Firstly I added traces to see all tasks being migrated with
migrate_live_tasks() and migrate_dead_tasks(). On my setup the problem
pops up (the one with "se == NULL" in the loop of
pick_next_task_fair()) shortly after the traces indicate that some has
been migrated with migrate_dead_tasks()). btw., I can reproduce it
much faster now with just a plain cpu down/up loop.
[disclaimer] Well, unless I'm really missing something important in
this late hour [/desclaimer] pick_next_task() is not something
appropriate for migrate_dead_tasks() :-)
the following change seems to eliminate the problem on my setup
(although, I kept it running only for a few minutes to get a few
messages indicating migrate_dead_tasks() does move tasks and the
system is still ok)
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
The commit 77d16f450ae0452d7d4b009f78debb1294fb435c ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Sat, 28 Jun 2008 03:12:32 +0000 (20:12 -0700)]
netlabel: Fix a problem when dumping the default IPv6 static labels
There is a missing "!" in a conditional statement which is causing entries to
be skipped when dumping the default IPv6 static label entries. This can be
demonstrated by running the following:
... you will notice that the entry for the IPv6 localhost address is not
displayed but does exist (works correctly, causes collisions when attempting
to add duplicate entries, etc.).
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Sat, 28 Jun 2008 03:09:00 +0000 (20:09 -0700)]
net/inet_lro: remove setting skb->ip_summed when not LRO-able
When an SKB cannot be chained to a session, the current code attempts
to "restore" its ip_summed field from lro_mgr->ip_summed. However,
lro_mgr->ip_summed does not hold the original value; in fact, we'd
better not touch skb->ip_summed since it is not modified by the code
in the path leading to a failure to chain it. Also use a cleaer
comment to the describe the ip_summed field of struct net_lro_mgr.
Issue raised by Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sat, 28 Jun 2008 03:06:08 +0000 (20:06 -0700)]
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
The problem is that while we work w/o the inet_frags.lock even
read-locked the secret rebuild timer may occur (on another CPU, since
BHs are still disabled in the inet_frag_find) and change the rnd seed
for ipv4/6 fragments.
It was caused by my patch fd9e63544cac30a34c951f0ec958038f0529e244
([INET]: Omit double hash calculations in xxx_frag_intern) late
in the 2.6.24 kernel, so this should probably be queued to -stable.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Zefan [Sat, 28 Jun 2008 03:03:24 +0000 (20:03 -0700)]
CONNECTOR: add a proc entry to list connectors
I got a problem when I wanted to check if the kernel supports process
event connector, and It seems there's no way to do this check.
At best I can check if the kernel supports connector or not, by looking
into /proc/net/netlink, or maybe checking the return value of bind() to
see if it's ENOENT.
So it would be useful to add /proc/net/connector to list all supported
connectors:
# cat /proc/net/connector
Name ID
connector 4294967295:4294967295
cn_proc 1:1
w1 3:1
Changelog:
- fix memory leak: s/seq_release/single_release
- use spin_lock_bh instead of spin_lock_irqsave
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Sat, 28 Jun 2008 02:54:05 +0000 (19:54 -0700)]
pkt_sched: Remove CONFIG_NET_SCH_RR
Commit d62733c8e437fdb58325617c4b3331769ba82d70
([SCHED]: Qdisc changes and sch_rr added for multiqueue)
added a NET_SCH_RR option that was unused since the code
went unconditionally into sch_prio.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Sat, 28 Jun 2008 02:34:18 +0000 (19:34 -0700)]
af_unix: fix 'poll for write'/connected DGRAM sockets
For n:1 'datagram connections' (eg /dev/log), the unix_dgram_sendmsg
routine implements a form of receiver-imposed flow control by
comparing the length of the receive queue of the 'peer socket' with
the max_ack_backlog value stored in the corresponding sock structure,
either blocking the thread which caused the send-routine to be called
or returning EAGAIN. This routine is used by both SOCK_DGRAM and
SOCK_SEQPACKET sockets. The poll-implementation for these socket types
is datagram_poll from core/datagram.c. A socket is deemed to be
writeable by this routine when the memory presently consumed by
datagrams owned by it is less than the configured socket send buffer
size. This is always wrong for PF_UNIX non-stream sockets connected to
server sockets dealing with (potentially) multiple clients if the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an (usual)
application to 'poll for writeability by repeated send request with
O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_recvmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Octavian Purdila [Sat, 28 Jun 2008 00:27:21 +0000 (17:27 -0700)]
tcp: fix for splice receive when used with software LRO
If an skb has nr_frags set to zero but its frag_list is not empty (as
it can happen if software LRO is enabled), and a previous
tcp_read_sock has consumed the linear part of the skb, then
__skb_splice_bits:
(a) incorrectly reports an error and
(b) forgets to update the offset to account for the linear part
Any of the two problems will cause the subsequent __skb_splice_bits
call (the one that handles the frag_list skbs) to either skip data,
or, if the unadjusted offset is greater then the size of the next skb
in the frag_list, make tcp_splice_read loop forever.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: calculate tcp_mem based on low memory instead of all memory
The tcp_mem array which contains limits on the total amount of memory
used by TCP sockets is calculated based on nr_all_pages. On a 32 bits
x86 system, we should base this on the number of lowmem pages.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6-omap-h63xx.git / log