Andy Walls [Wed, 3 Sep 2008 20:11:54 +0000 (17:11 -0300)]
V4L/DVB (8769): cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues()
cx18: Simplify queue flush logic to prevent oops in cx18_flush_queues().
If accounting of a queue is in error, logic borrowed from ivtv will cause
an oops when flushing the queues for a stream. This change greatly
simplifies the queue flush logic, and sets the queue back to sane
defaults on a flush.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (8751): vivi: Fix some issues at vivi register routine
This patch fixes several small issues at vivi register routines:
1) minor and n_devs should be unsigned;
2) n_devs = 0 were not properly handled;
3) if n_devs specify a high number, the driver would just roll back and
won't register any device. The proper behaviour is to keep all succeded
devices registered;
4) both n_devs and minor were using 0 as permissions. Better to have
them with 0444.
With the current patch, if n_devs specify a very large value, it will
register all possible devices. For example, on a machine without any
other V4L drivers loaded, with this patch, we will have something like:
vivi: V4L2 device registered as /dev/video0
vivi: V4L2 device registered as /dev/video1
vivi: V4L2 device registered as /dev/video2
...
vivi: V4L2 device registered as /dev/video31
video_register_device_index: get_index failed
Video Technology Magazine Virtual Video Capture Board ver 0.5.0 successfully loaded.
5) The number of allocated devices on success is now kept at n_devs:
$ cat /sys/module/vivi/parameters/n_devs
32
Thanks to Henne <henne@nachtwindheim.de> for pointing that there were
some issues at vivi.
Cc: Henne <henne@nachtwindheim.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On 10-08-08 23:37, Alan Cox wrote:
>
> Would probably make the printk "pms: not enabled, use pms.enable=1 to
> probe"
>
> So you know
> a) What is wittering about not being probed
> b) How to undo it.
>
> But thats trivia really.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rene Herman [Wed, 3 Sep 2008 19:48:21 +0000 (16:48 -0300)]
V4L/DVB (8727): V4L1: make PMS not autoprobe when builtin.
The old Mediavision Pro Movie Studio legacy ISA V4L1 driver was found to
hang the boot during Ingo Molnar's testing of randconfig kernels. Have it
require a "pms.enable=1" kernel parameter to enable the driver when
builtin which avoids such problems.
This is a deprecated and, very likely, unused driver. Nothing changes
modular behaviour moreover.
Signed-off-by: Rene Herman <rene.herman@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Simon Arlott [Wed, 3 Sep 2008 19:48:20 +0000 (16:48 -0300)]
V4L/DVB (8726): link tuner before saa7134
If saa7134_init is run before v4l2_i2c_drv_init (tuner), then
saa7134_board_init2 will try to set the tuner type for devices that don't
exist yet. This moves tuner to before all of the device-specific drivers
so that it's loaded early enough on boot.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans de Goede [Wed, 3 Sep 2008 19:48:16 +0000 (16:48 -0300)]
V4L/DVB (8720): gspca: V4L2_CAP_SENSOR_UPSIDE_DOWN added as a cap for some webcams.
This patch adds a V4L2_CAP_SENSOR_UPSIDE_DOWN flag to the capabilities flags,
and sets this flag for the Philips SPC200NC cam (which has its sensor installed
upside down). The same flag is also needed and added for the Philips SPC300NC.
Together with a patch to libv4l which adds flipping the image in software this
fixes the upside down display with the SPC200NC cam.
Signed-of-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 3 Sep 2008 19:47:50 +0000 (16:47 -0300)]
V4L/DVB (8701): cx18: Add missing lock for when the irq handler manipulates the queues
cx18: Add missing lock for when the irq handler manipulates the queues. This
was a potential source of stream queue corruption. Also changed the name of
cx18_queue_find_buf() to cx18_queue_get_buf_irq().
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG frames generated by the Pixart 73xx have:
- special markers 'ff ff ff xx' every 1024/512 bytes,
- unused 8 bits at end of JPEG blocks,
and then ask for a new pixel format.
Bug register/value inversions in USB exchanges.
Exposure and gain controls added for rev 12a.
Separate the functions and controls of the revisions 12a and 72a.
Hans de Goede [Wed, 3 Sep 2008 19:47:28 +0000 (16:47 -0300)]
V4L/DVB (8667): gspca: Bad probe of Z-Star/Vimicro webcams with pas106 sensor.
This patch moves the detection of the 2wr SIF pas106b sensor to before
detecting other sensors.
Patch change by jfm: Check SIF for identified webcams only.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Wed, 3 Sep 2008 19:47:14 +0000 (16:47 -0300)]
V4L/DVB (8648): ivtv: improve CC support
- change the work-queue to a single threaded high prio workqueue
- use DMA instead of PIO for the sliced VBI data.
- remove some incorrect tests
- increase the internal VBI capture queue size for sliced VBI packets
- ignore duplicate VBI lines
With these changes it should finally be possible to get reliable closed
captions.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Wed, 3 Sep 2008 19:46:58 +0000 (16:46 -0300)]
V4L/DVB (8633): ivtv: update ivtv version number
Since for 2.6.27 ivtvfb uses DMA for write it is important that
you can identify which ivtv version supports this and which doesn't.
Increase the version number so we can tell the difference.
Thanks to Ian Armstrong for pointing this out to me.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Linus Torvalds [Sat, 30 Aug 2008 03:18:31 +0000 (20:18 -0700)]
Resource handling: add 'insert_resource_expand_to_fit()' function
Not used anywhere yet, but this complements the existing plain
'insert_resource()' functionality with a version that can expand the
resource we are adding in order to fix up any conflicts it has with
existing resources.
Andi Kleen [Fri, 29 Aug 2008 18:06:23 +0000 (20:06 +0200)]
Don't trigger softlockup detector on network fs blocked tasks
Pulling the ethernet cable on a 2.6.27-rc system with NFS mounts
currently leads to an ongoing flood of soft lockup detector backtraces
for all tasks blocked on the NFS mounts when the hickup takes
longer than 120s.
I don't think NFS problems should be all that noisy.
Luckily there's a reasonably easy way to distingush this case.
Don't report task softlockup warnings for tasks in TASK_KILLABLE
state, which is used by the network file systems.
It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.
Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Yinghai Lu <yhlu.kernel@gmail.com> Cc: David Witbrodt <dawitbro@sbcglobal.net> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clemens Ladisch [Fri, 29 Aug 2008 11:08:34 +0000 (13:08 +0200)]
ALSA: oxygen: fix distorted output on AK4396-based cards
When changing the sample rate, the CMI8788's master clock output becomes
unstable for a short time. The AK4396 needs the master clock to do SPI
writes, so writing to an AK4396 control register directly after a sample
rate change will garble the value. In our case, this leads to the DACs
being misconfigured to I2S sample format, which results in a wrong
output level and horrible distortions on samples louder than -6 dB.
To fix this, we need to wait until the new master clock signal has
become stable before doing SPI writes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Thu, 28 Aug 2008 19:34:01 +0000 (12:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: Fix PM building on BF52x: No ROTWE on BF52x, add USBWE
Blackfin arch: sram: use 'unsigned long' for irqflags
Blackfin arch: let PCI depend on BROKEN
Blackfin arch: move include/asm-blackfin header files to arch/blackfin
Blackfin arch: fix bug - MPU crashes under stress
Blackfin arch: Fix bug - when to rmmod the L1_module, it stucks and then reboot the board.
Blackfin arch: dont actually need to muck with EMAC_SYSTAT for BF52x for demuxing
Blackfin arch: Add MTD Partitions for MTD_DATAFLASH, increase max SPI SCLK
In accordance with commit f42ac38c59e0a03d6da0c24a63fb211393f484b0
("ftrace: disable tracing for suspend to ram"), disable tracing
around the suspend code in hibernation code paths.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Zijlstra [Tue, 19 Aug 2008 10:33:03 +0000 (12:33 +0200)]
sched: rt-bandwidth accounting fix
It fixes an accounting bug where we would continue accumulating runtime
even though the bandwidth control is disabled. This would lead to very long
throttle periods once bandwidth control gets turned on again.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Vegard Nossum [Thu, 28 Aug 2008 09:28:46 +0000 (17:28 +0800)]
Blackfin arch: sram: use 'unsigned long' for irqflags
Using just 'unsigned' will make flags an unsigned int. While this is
arguably not an error on blackfin where sizeof(int) == sizeof(long),
the patch is still justified on the grounds of principle.
The patch was generated using the Coccinelle semantic patch framework.
Cc: Julia Lawall <julia@diku.dk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
John Blackwood [Tue, 26 Aug 2008 19:09:43 +0000 (15:09 -0400)]
sched: fix sched_rt_rq_enqueue() resched idle
When sysctl_sched_rt_runtime is set to something other than -1 and the
CONFIG_RT_GROUP_SCHED kernel parameter is NOT enabled, we get into a state
where we see one or more CPUs idling forvever even though there are
real-time
tasks in their rt runqueue that are able to run (no longer throttled).
The sequence is:
- A real-time task is running when the timer sets the rt runqueue
to throttled, and the rt task is resched_task()ed and switched
out, and idle is switched in since there are no non-rt tasks to
run on that cpu.
- Eventually the do_sched_rt_period_timer() runs and un-throttles
the rt runqueue, but we just exit the timer interrupt and go back
to executing the idle task in the idle loop forever.
If we change the sched_rt_rq_enqueue() routine to use some of the code
from the CONFIG_RT_GROUP_SCHED enabled version of this same routine and
resched_task() the currently executing task (idle in our case) if it is
a lower priority task than the higher rt task in the now un-throttled
runqueue, the problem is no longer observed.
Signed-off-by: John Blackwood <john.blackwood@ccur.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jean Delvare [Thu, 28 Aug 2008 06:33:23 +0000 (08:33 +0200)]
i2c: Prevent log spam on some DVB adapters
Some DVB adapters do not support the special I2C transaction that we
use for probing purposes. There's no point in logging this event, as
there's nothing the user can do and in general there is no actual
problem. So, degrade one of these messages to a debug message, and
move the other one around so that it is only printed on bogus drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Vlad Yasevich [Wed, 27 Aug 2008 23:09:49 +0000 (16:09 -0700)]
sctp: fix random memory dereference with SCTP_HMAC_IDENT option.
The number of identifiers needs to be checked against the option
length. Also, the identifier index provided needs to be verified
to make sure that it doesn't exceed the bounds of the array.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
IB/mlx4: Actually return L_Key and R_Key for fast register MRs
Initialize the L_Key and R_Key for memory regions returned from
mlx4_ib_alloc_fast_reg_mr(). Otherwise callers just get garbage for
the memory keys and can't do anything useful with these MRs.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Tue, 26 Aug 2008 18:55:58 +0000 (19:55 +0100)]
tty: Fix termios tty window resize race with pty/tty pair
Kanru Chen posted a patch versus the old code which deals with the case
where you resize the pty side of a pty/tty pair. In that situation the
termios data is updated for both pty and tty but the locks are not held
for the right side.
This implements the fix differently against the updated tty code. Patch
by self but the hard bit (noticing and fixing the bug) is thanks to Kanru
Chen.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 27 Aug 2008 21:31:44 +0000 (14:31 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] deal with the first call of ->show() generating no output
[PATCH] fix ->llseek() for a bunch of directories
[PATCH] fix regular readdir() and friends
[PATCH] fix hpux_getdents()
[PATCH] fix osf_getdirents()
[PATCH] ntfs: use d_add_ci
[PATCH] change d_add_ci argument ordering
[PATCH] fix efs_lookup()
[PATCH] proc: inode number fixlet
Linus Torvalds [Wed, 27 Aug 2008 21:28:45 +0000 (14:28 -0700)]
Merge branch 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: don't set the signal blocker on the master process.
drm: don't call the vblank tasklet with irqs disabled.
r300: Fix cliprect emit
drm/radeon: r300_cmdbuf: Always emit INDX_BUFFER immediately after DRAW_INDEX
radeon: fix some hard lockups on r3/4/500s
Jeff Layton [Wed, 27 Aug 2008 17:53:30 +0000 (17:53 +0000)]
[CIFS] Add destroy routine for dns_resolver
Otherwise, we're leaking the payload memory.
CC: Stable Kernel <stable@vger.kernel.org> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Wed, 27 Aug 2008 08:14:46 +0000 (01:14 -0700)]
e1000: fix stack size
Here's the patch. It shrinks the stack from 1152 bytes to 192 bytes (the
first version, that only did the e1000_option part, got it down to 600
bytes). About half comes from not using multiple "e1000_option"
structures, the other half comes from turning the "e1000_opt_list[]"
arrays into "static const" instead, so that gcc doesn't copy them onto the
stack.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Reveiewed-by: Auke Kok <auke-jan.h.kok@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 27 Aug 2008 20:55:35 +0000 (13:55 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove blk_queue_tag_depth() and blk_queue_tag_queue()
block: remove unused ->busy part of the block queue tag map
bio: fix __bio_copy_iov() handling of bio->bv_len
bio: fix bio_copy_kern() handling of bio->bv_len
block: submit_bh() inadvertently discards barrier flag on a sync write
block: clean up cmdfilter sysfs interface
block: rename blk_scsi_cmd_filter to blk_cmd_filter
sg: restore command permission for TYPE_SCANNER
block: move cmdfilter from gendisk to request_queue
Linus Torvalds [Wed, 27 Aug 2008 20:54:55 +0000 (13:54 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Increment the reference count of an already-active stack.
[PATCH] configfs: Consolidate locking around configfs_detach_prep() in configfs_rmdir()
ocfs2: correctly set i_blocks after inline dir gets expanded
ocfs2: Jump to correct label in ocfs2_expand_inline_dir()
ocfs2: Fix sleep-with-spinlock recovery regression
[PATCH] ocfs2/cluster/netdebug.c: fix warning
[PATCH] ocfs2/cluster/tcp.c: make some functions static
Steven Rostedt [Wed, 27 Aug 2008 13:14:40 +0000 (09:14 -0400)]
ftrace: disable tracing for suspend to ram
I've been painstakingly debugging the issue with suspend to ram and
ftraced. The 2.6.28 code does not have this issue, but since the mcount
recording is not going to be in 27, this must be solved for the ftrace
daemon version.
The resume from suspend to ram would reboot because it was triple
faulting. Debugging further, I found that calling the mcount function
itself was not an issue, but it would fault when it incremented
preempt_count. preempt_count is on the tasks info structure that is on the
low memory address of the task's stack. For some reason, it could not
write to it. Resuming out of suspend to ram does quite a lot of funny
tricks to get to work, so it is not surprising at all that simply doing a
preempt_disable() would cause a fault.
Thanks to Rafael for suggesting to add a "while (1);" to find the place in
resuming that is causing the fault. I would place the loop somewhere in
the code, compile and reboot and see if it would either reboot (hit the
fault) or simply hang (hit the loop). Doing this over and over again, I
narrowed it down that it was happening in enable_nonboot_cpus.
At this point, I found that it is easier to simply disable tracing around
the suspend code, instead of searching for the particular function that
can not handle doing a preempt_disable.
This patch disables the tracer as it suspends and reenables it on resume.
I tested this patch on my Laptop, and it can resume fine with the patch.
Signed-off-by: Steven Rostedt <srostedt@redhat.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In particular, the "struct file *" and the "struct inode *" arguments do
not necessarily match, which means that the unlocked version of the
ioctl (that only gets a "struct file *") isn't actually able to handle
the cases it needs to handle.
This fixes bugzilla
http://bugzilla.kernel.org/show_bug.cgi?id=11401
Reported-and-bisected-by: Laurent Riffard <laurent.riffard@free.fr> Acked-by: Peter Osterlund <petero2@telia.com> Cc: Alan Cox <alan@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 14 Aug 2008 10:10:14 +0000 (11:10 +0100)]
[ARM] Skip memory holes in FLATMEM when reading /proc/pagetypeinfo
Ordinarily, memory holes in flatmem still have a valid memmap and is safe
to use. However, an architecture (ARM) frees up the memmap backing memory
holes on the assumption it is never used. /proc/pagetypeinfo reads the
whole range of pages in a zone believing that the memmap is valid and that
pfn_valid will return false if it is not. On ARM, freeing the memmap breaks
the page->zone linkages even though pfn_valid() returns true and the kernel
can oops shortly afterwards due to accessing a bogus struct zone *.
This patch lets architectures say when FLATMEM can have holes in the
memmap. Rather than an expensive check for valid memory, /proc/pagetypeinfo
will confirm that the page linkages are still valid by checking page->zone
is still the expected zone. The lookup of page_zone is safe as there is a
limited range of memory that is accessed when calling page_zone. Even if
page_zone happens to return the correct zone, the impact is that the counters
in /proc/pagetypeinfo are slightly off but fragmentation monitoring is
unlikely to be relevant on an embedded system.
Reported-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Mel Gorman <mel@csn.ul.ie> Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6-omap-h63xx.git / log