Some machines don't have the pullup/down on their reset
pin, so configuring the reset generating pin as input makes
them reset immediately. Fix that by making reset pin direction
configurable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Tue, 7 Oct 2008 19:44:07 +0000 (20:44 +0100)]
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
Fix two warnings when compiling for the KS8695 processor.
arch/arm/include/asm/dma-mapping.h: In function 'dma_to_virt':
arch/arm/include/asm/dma-mapping.h:40: warning: return makes pointer
from integer without a cast
Section mismatch in reference from the function pcibios_fixup_bus() to
the (unknown reference) .devinit.text:(unknown)
The function pcibios_fixup_bus() references
the (unknown reference) __devinit (unknown).
This is often because pcibios_fixup_bus lacks a __devinit
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Sat, 4 Oct 2008 04:45:39 +0000 (12:45 +0800)]
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Fri, 3 Oct 2008 14:37:21 +0000 (22:37 +0800)]
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
Depending on the order of how resource is defined in the platform
device is not good, use platform_get_{irq,resource} for the IRQ
and memory resources.
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Sat, 27 Sep 2008 07:49:57 +0000 (15:49 +0800)]
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Mon, 8 Sep 2008 07:37:50 +0000 (15:37 +0800)]
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
Signed-off-by: Eric Miao <eric.miao@marvell.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:30:42 +0000 (10:30 +0100)]
[ARM] 5285/1: pxa: update xm_x2xx_defconfig
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:29:59 +0000 (10:29 +0100)]
[ARM] 5284/1: pxa: cm-x255: add NOR and NAND flash support
This patch adds support for NOR and NAND flashes on CM-X255.
The NAND flash support uses not yet merged GPIO NAND driver.
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:27:22 +0000 (10:27 +0100)]
[ARM] 5283/1: pxa: add CM-X255 pcmcia support
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:26:55 +0000 (10:26 +0100)]
[ARM] 5282/1: pxa: add CM-X255 support
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:26:10 +0000 (10:26 +0100)]
[ARM] 5281/1: pxa: split cm-x2xx.c to cm-x2xx.c and cm-x270.c
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Sun, 5 Oct 2008 09:25:44 +0000 (10:25 +0100)]
[ARM] 5280/1: pxa: prepare cm-x2xx.c and cm-x2xx-pci.[ch] for addition of CM-X255
- Change CM-X255 and CM-X270 common function prefix from cmx270 to cmx2xx
- Split cmx2xx_init to common and CM-X270-specific parts
- Use dynamic assignement for DM9000 resources and led GPIOs.
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mike Rapoport [Tue, 7 Oct 2008 10:58:25 +0000 (11:58 +0100)]
[ARM] 5286/2: pxa: rename cm-x270* to cm-x2xx* to allow addition of cm-x255 support
Signed-off-by: Russ Dill <russ.dill@gmail.com> Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hartley Sweeten [Mon, 6 Oct 2008 21:43:02 +0000 (22:43 +0100)]
[ARM] 5293/1: ep93xx: add defines for external chipselects
This patch adds defines for the external chipselect physical base
addresses available with the EP93xx. These are meant to be used
in the platform init code.
In addition, documentation about the synchronous/asynchronous boot
modes for the EP93xx and a reference to errata about issues with
synchronous booting has been added.
Signed-off-by: <H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hartley Sweeten [Sat, 4 Oct 2008 19:01:49 +0000 (20:01 +0100)]
[ARM] 5273/2: ep93xx: move ethernet support into core.c
All EP93xx based systems can support Ethernet. This patch moves
the platform_device setup from the various board support files
into the core support file. The Ethernet driver data still remains
in the individual platform setup files to allow specific platform
configuration.
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Fri, 3 Oct 2008 10:09:10 +0000 (11:09 +0100)]
[ARM] 5229/3: Replace some ARMv7 opcodes with the instruction name
These instructions were placed in the code directly as opcodes because
early compilers didn't support them. Toolchains supporting ARMv7
understand these instructions and the patch puts the mnemonics back.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hartley Sweeten [Thu, 2 Oct 2008 16:13:02 +0000 (17:13 +0100)]
[ARM] 5276/1: ep93xx: allow selecting UART for early kernel messages
Currently on the EP93xx platform early kernel messages go to UART1.
Since this UART is the only one that has modem control signals it
might be used for another purpose and it is undesirable for those
messages to appear. This patch allows one of the other UARTs to be
selected in the kernel configuration. It is assumed that the
bootloader has configured and initialized the UART since this was the
previous assumption.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Marek Vašut [Thu, 11 Sep 2008 18:37:32 +0000 (19:37 +0100)]
[ARM] 5248/1: wm97xx generic battery driver
This patch adds generic battery driver for wm97xx chips.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Anton Vorontsov <cbouatmailru@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point converting memory bank addresses from physical to
virtual just to convert them back to physical addresses. Furthermore
this isn't "right" for highmem even if in this case the end result is
the correct one.
Signed-off-by: Nicolas Pitre <nico@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dick Hollenbeck [Tue, 16 Sep 2008 17:30:27 +0000 (18:30 +0100)]
[ARM] 5250/1: unbalanced enable_irq() for serial_ks8695.c fix
The function ks8695uart_set_termios() would cause an unbalanced
enable_irq() generated message to be printk()ed. This is because
there was no book keeping support to remember if the calls to
enable_irq() and disable_irq() were balanced for the modem
control irq.
Signed-off-by: Dick Hollenbeck <dick@softplc.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jürgen Schindele [Tue, 16 Sep 2008 20:36:30 +0000 (21:36 +0100)]
[ARM] 5251/1: remove old LED support for Trizeps4 SOM
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jürgen Schindele [Mon, 18 Aug 2008 20:45:03 +0000 (21:45 +0100)]
[ARM] 5204/1: Trizeps4 SOM update
- use MFP-API for GPIO
- support TRIZEPS4WL module
- cleanups
Signed-off-by: Jrgen Schindele <linux@schindele.name> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the jornada default
config (which was made for 2.6.12). Plenty
of development has happend since then, most
importantly the SSP driver and kbd/touchscr.
This config has been tested to compile
and bootup properly.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 1 Oct 2008 15:58:32 +0000 (16:58 +0100)]
[ARM] mm: finish ARM sparsemem support
... including some comments about the ordering required to bring
sparsemem up. You have to repeatedly guess, test, reguess, try
again and again to work out what the right ordering is. Many
hours later...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 1 Oct 2008 15:56:15 +0000 (16:56 +0100)]
[ARM] mm: provide helpers for accessing membanks
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 7 Sep 2008 16:16:54 +0000 (17:16 +0100)]
[ARM] Improve non-executable support
Add support for detecting non-executable stack binaries, and adjust
permissions to prevent execution from data and stack areas. Also,
ensure that READ_IMPLIES_EXEC is enabled for older CPUs where that
is true, and for any executable-stack binary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 7 Sep 2008 11:42:51 +0000 (12:42 +0100)]
[ARM] Remove MT_DEVICE_IXP2000 and associated definitions
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 6 Sep 2008 19:04:59 +0000 (20:04 +0100)]
[ARM] Introduce new PTE memory type bits
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 30 Sep 2008 18:31:44 +0000 (19:31 +0100)]
[ARM] mm: move vmalloc= parsing to arch/arm/mm/mmu.c
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 30 Sep 2008 18:29:25 +0000 (19:29 +0100)]
[ARM] mm: move validation of membanks to one place
The newly introduced sanity_check_meminfo() function should be
used to collect all validation of the meminfo array, which we
have in bootmem_init(). Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 29 Sep 2008 18:50:59 +0000 (19:50 +0100)]
[ARM] dma: don't touch cache on dma_*_for_cpu()
As per the dma_unmap_* calls, we don't touch the cache when a DMA
buffer transitions from device to CPU ownership. Presently, no
problems have been identified with speculative cache prefetching
which in itself is a new feature in later architectures. We may
have to revisit the DMA API later for these architectures anyway.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Wed, 24 Sep 2008 21:03:52 +0000 (22:03 +0100)]
[ARM] 5267/1: [AT91] Name conflict in mach-at91/leds.c
The name of the platform device 'at91_pwm_leds' conflicts with the
function at91_pwm_leds().
So rename the device 'at91_pwm_leds_device' to be more specific.
Similarly rename 'at91_gpio_leds_device' for consistency.
Signed-off-by: Andrew Victor <linux@maxim.org.za> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Mon, 29 Sep 2008 12:48:17 +0000 (13:48 +0100)]
[ARM] dma: add validation of DMA params
Validate the direction argument like x86 does. In addition,
validate the dma_unmap_* parameters against those passed to
dma_map_* when using the DMA bounce code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The dmabounce dma_sync_xxx() implementation have been broken for
quite some time; they all copy data between the DMA buffer and
the CPU visible buffer no irrespective of the change of ownership.
(IOW, a DMA_FROM_DEVICE mapping copies data from the DMA buffer
to the CPU buffer during a call to dma_sync_single_for_device().)
Fix it by getting rid of sync_single(), moving the contents into
the recently created dmabounce_sync_for_xxx() functions and adjusting
appropriately.
This also makes it possible to properly support the DMA range sync
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Fri, 12 Sep 2008 02:45:41 +0000 (10:45 +0800)]
[ARM] pxa/pcm027: convert to use new MFP API
Signed-off-by: Eric Miao <eric.miao@marvell.com> Acked-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao [Fri, 8 Aug 2008 06:33:29 +0000 (14:33 +0800)]
[ARM] pxa/idp: remove the unnecessary idp_init_irq()
TOUCH_PANEL_IRQ is never referenced, and set_irq_type() shouldn't
be called in this way, remove it, as well as the idp_init_irq(),
and use pxa25x_init_irq() instead.
Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Cliff Brake <cliff.brake@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
projects / linux-2.6-omap-h63xx.git / log